Test Report

FCC ID: PJIL21C0FAL0

Test Report

Download: PDF
FCCID_1970278

www.etl.re.kt @—Testing Laboratory Electromagnetic Emission FCC ME ASUREMENT REP ORT CERTIFICATION OF COMPLIANCE FCC Part 15 Certification Measurement PRODUCT LCD MONITOR MODELITYPE NO L21COFALO / NONE FCC ID PJIL21COFALO MULTIPLE MODEL P227D, P227DS, P227DL, P227DT, P227DU, P227DV BRAND NAME +HYUNDAI APPLICANT HYUNDAI IBT CORP 106, Apogongdan—gil, Gimcheon—si, Gyeongsangbuk—do, 740—862, Korea Attn.: Yoon Suk Lee / Manager MANUFACTURER HYUNDAI IBT CORP 106, Apogongdan—gil, Gimcheon—si, Gyeongsangbuk—do, 740—862, Korea FCC CLASSIFICATION Class B Personal computers and peripherals RULE PART(S) FCC Part 15 Subpart B & ICES—003 Issue 4 TEST PROCEDURE ANSI C63.4—2003 TEST REPORT No. ETLE130417.0397 DATES OF TEST May 02, 2013 to May 03, 2013 REPORT ISSUE DATE May 16, 2013 TEST LABORATORY ETL Inc. (FCC Designation Number: KROO22, IC OATS Number: 6473B—1) This LCD MONITOR, Model L21COFALO has been tested in accordance with the measurement procedures specified in ANSI €63.4—2003 at the ETL/EMC Test Laboratory and has been shown to be complied with the electromagnetic radiated emission limits specified in FCC Rule Part15 Subpart B & ICES—003 Issue 4: 1 attest to the accuracy of data. All measurement herein was performed by me or was made under my supervision and is correct to the best of my knowledge and belief. | assume full responsibilty for the completeness of these measurements and vouch for the qualifications of all persons taking them. The results of testing in this report apply to the product/system which was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties Prepared by:%? Reviewed by: U# Jeong Hwan, Pyo (Test Engineer) Hyung Min, Choi (Chief Engineer) May 16, 2013 May 16, 2013 ETL Inc. #371—51, Gasan—dong, Geumcheon—gu, Seoul, 153—803, Korea Tel: 82—2—858—0786 Fax: 82—2—858—0788 The test report merely corresponds to the test sample(s) This report shall not be reproduced, in whole or in part without the written approval of ETL Inc.

FCC TEST REPORT FCC ID: PJIL21C0FAL0 Table of Contents FCC Measurement Report 1. Introduction 2. Product Information 3. Description of Tests 4. Test Condition 5. Test Results 5.1 Summary of Test Results 5.2 Conducted Emissions Measurement 5.3 Radiated Emissions Measurement 6. Sample Calculation 7. List of test Equipment used for Measurement Appendix B. Test Setup Photographs Appendix C. External Photographs Appendix D. Internal Photographs Report no. ETLE130417.0397, Page 2 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 FCC MEASUREMENT REPORT Scope – Measurement and determination of electromagnetic emission(EME) of radio frequency devices including intentional radiators and/or unintentional radiators for compliance with the technical rules and regulations of the U.S Federal Communications Commission(FCC) General Information Applicant Name : HYUNDAI IBT CORP. Address : 106, Apogongdan-gil, Gimcheon-si, Gyeongsangbuk-do, 740-862, Korea Attention : Yoon Suk Lee / Manager  EUT Type : LCD MONITOR  Model Number : L21C0FAL0  S/N : -  Frequency Range : X-tal  14.318 MHz; F/MEMORY clock  85 kHz; LVDS clock  74.250 MHz  Rule Part(s) : FCC Part 15 Subpart B & ICES-003 Issue 4  Test Procedure : ANSI C63.4-2003  FCC Classification : Class B Personal computers and peripherals  Dates of Tests : May 02, 2013 to May 03, 2013  Place of Tests : ETL Inc. Testing Lab. (FCC Designation Number : KR0022) Radiated Emission test; #499-1, Sagot-ri, Seosin-myeon, Hwaseong-si, Gyeonggi-do, 445-882, Korea Conducted Emission test; ETL Inc. Testing Lab. (FCC Designation Number : KR0022) 371-51, Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea  Test Report No. : ETLE130417.0397 Report no. ETLE130417.0397, Page 3 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 1. INTRODUCTION The measurement tests for radiated and conducted emission test were conducted at the ETL Inc. The site is constructed in conformance with the requirements of the ANSI C63.4-2003 and CISPR Publication 16. The ETL has site descriptions on file with the FCC for 3 m and 10 m site configurations. Detailed description of test facility was found to be in compliance with the requirements of Section 2.948 FCC Rules according to the ANSI C63.4-2003 and registered to the Federal Communications Commission (FCC Designation Number : KR0022). The measurement procedure described in American National Standard for Method of Measurement of Radio- Noise Emission from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz (ANSI C63.4-2003) was used in determining radiated and conducted emissions from the HYUNDAI IBT CORP., Model: L21C0FAL0. Report no. ETLE130417.0397, Page 4 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 2. PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LCD MONITOR (model: L21C0FAL0). The model L21C0FAL0 is basic model that was tested. The model differences are same with below table; Model name DVI VGA Speaker USB Lift stand Tilt stand L21C0FAL0 O O O O O O P227D O O X X X O P227DS O O O X X O P227DL O O X X O X P227DT O O O X O X P227DU O O O O O X P227DV O O X O O X * O: Existence, X: Non-existence Report no. ETLE130417.0397, Page 5 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 2.2 General Specification Item Specification Visible Screen Area 476.64 mm (H) x 268.11 mm (V) (21.5 Inch) Pixel Pitch 0.248 mm (H) x 0.248 mm (V) Recommended Resolution 1 920 x 1 080 @ 60 Hz Maximum Visible Angle 170°/170° (H/V) LCD Displayed Color 16.7 M Brightness 250 cd/m2 Contrast Ratio 1 000:1 Response Time 5 msec Horizontal Frequency 30 kHz – 80 kHz Vertical Frequency 60 kHz – 75 kHz Input Signal Video Signal Analog VGA, DVI Connector DVI-I, AUDIO, USB Power Consumption < 25 W (Typ.) Power Stand by Power < 0.5 W Input Power AC 100 V – 240 V; 50 Hz/60 Hz; 2.0 A Multimedia Speakers 1Wx2 Temperature: (25 ± 15) ℃ Operation Operating Humidity: (50 ± 30) % (non-condensing) Environment Temperature: (20 ± 30) ℃ Storage Humidity: (50 ± 40) % (non-condensing) Report no. ETLE130417.0397, Page 6 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 3. DESCRIPTION OF TESTS 3.1 Conducted Emission Measurement Conducted emissions measurements were made in accordance with section 11, "Measurement of Information Technology Equipment" of ANSI C63.4-2003. The measurements were performed over the frequency range of 0.15 MHz to 30 MHz using a 50 Ω/50 μH LISN as the input transducer to a Spectrum Analyzer or a Test Receiver. The measurements were made with the detector set for "Peak" amplitude within a bandwidth of 9 kHz or for "quasi-peak" within a bandwidth of 9 kHz. The line-conducted emission test is conducted inside a shielded anechoic chamber room with 1 m x 1.5 m x 0.8 m wooden table which is placed 40 cm away from the vertical wall and 1.5 m away from the side wall of the chamber room. Two LISN are bonded to the shielded room. The EUT is powered from the LISN and the support equipment is powered from the other LISN. Power to the LISNs are filtered by a noise cut power line filters. All electrical cables are shielded by braided tinned steel tubing with inner  1.2 cm. If the EUT is a DC-powered device, power will be derived from the source power supply it normally will be powered from and these supply lines will be connected to the LISN. Non-inductive bundling to a 1 m length shortened all interconnecting cables more than 1 m. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The RF output of the LISN was connected to the EMI Test Receiver to determine the frequency producing the maximum emission from the EUT. The frequency producing the maximum level was reexamined using to set Quasi-Peak mode by manual, after scanned by automatic Peak mode from 0.15 MHz to 30 MHz. The bandwidth of the spectrum analyzer was set to 9 kHz. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Photographs of the worst-case emission can be seen in photographs of conducted emission test setup in Appendix B. Report no. ETLE130417.0397, Page 7 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 3.2 Radiated Emission Measurement Radiated emission measurements were made in accordance with section 11, "Measurement of Information Technology Equipment" of ANSI C63.4-2003. The measurements were performed over the frequency range of 30 MHz to 40 GHz (or 5th harmonic of the highest frequency) in using antenna as the input transducer to a spectrum analyzer or a field intensity meter. The measurements below 1 GHz were made with the detector set for "Quasi-peak" within a bandwidth of 120 kHz. The measurements above 1 GHz were made with the detector set for "Peak and Average" within a bandwidth of 1 MHz. Preliminary measurements were made at 3 m using broadband antennas, and spectrum analyzer to determined the frequency producing the maximum emission in shielded room. Appropriate precaution was taken to ensure that all emission from the EUT were maximized and investigated. The system configuration, mode of operation, turntable azimuth and height with respect to the antenna were noted for each frequency found. The spectrum was scanned from 30 MHz to 1 000 MHz using Log-Bicon antenna. Above 1 GHz, linearly polarized double ridge horn antennas were used. Final measurements were made open site at 3 m. The test equipment was placed on a wooden turn-table. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. Each frequency found during pre-scan measurements was re-examined by manual. The detector function was set to CISPR Quasi-peak mode and the bandwidth of the receiver was set to 120 kHz or 1 MHz depending on the frequency of type of signal. The EUT, support equipment and interconnecting cables were re-configured to the set-up producing the maximum emission for the frequency and were placed on top of a 0.8 m high nonmetallic 1 m x 1.5 m table. The EUT, support equipment, and interconnecting cables were re-arranged and manipulated to maximize each emission. The turntable containing the system was rotated; the antenna height was varied 1 m to 4 m and stopped at the azimuth or height producing the maximum emission. Each emission was maximized by: varying the mode of operation to the EUT and/or support equipment and changing the polarity of the antenna, whichever determined the worst-case emission. Photographs of the worst-case emission can be seen in Photographs of the worst-case emission test setup can be seen in Appendix B. Report no. ETLE130417.0397, Page 8 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 4. TEST CONDITION 4.1 Test Configuration The device was configured for testing in a typical fashion (as a customer would normally use it). During the tests, the EUT and the supported equipments were installed to meet FCC requirement and operated in a manner and which tends to maximize its emission level in a typical application. 4.2 EUT operation The equipment under test was operated during the measurement under following conditions: Conditions Remark  Standby mode The EUT was connected as user’s guide. And during the executed test  VGA mode & USB mode * program for EMI program with "H" pattern display on monitor. The EUT was connected as user’s guide. And during the executed test  DVI mode & USB mode program for EMI program with "H" pattern display on monitor. * The worst case was investigated for emission test. 4.3 Support Equipment Used Description Model Name Serial No. Manufacturer FCC PC D08M 6GPJXBX Dell Inc. DoC Shenzhen Jiayewang Keyboard IGK-5300 NONE - Technology Co.,Ltd. Tonzo Industrial Co., Mouse MO-2100 NONE DoC Ltd. USB Drive (4 GB) SUM-BSY4G NONE Samsung Electronics - Report no. ETLE130417.0397, Page 9 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 4.4 Type of Cables Used Used Device from Device to Type of I/O port Length[m] Type of shield ferrite core EUT PC VGA 1.5 Shielded O EUT PC DVI 1.5 Shielded O EUT PC PC Audio In 1.5 Shielded O EUT PC USB 1.2 Shielded X EUT USB Drive USB - - - EUT Power socket AC Input 1.2 Unshielded X PC Keyboard USB 1.2 Shielded X PC Mouse USB 1.2 Shielded X PC Power socket AC Input 1.2 Unshielded X Report no. ETLE130417.0397, Page 10 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 4.5 The setup drawing(s) USB Drive EUT PC Keyboard Mouse : Signal line : Power line : Adapter Report no. ETLE130417.0397, Page 11 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 5. TEST RESULTS 5.1 Summary of Test Results The measurement results were obtained with the EUT tested in the conditions described in this report. Detailed measurement data and plots showing the maximum emission of the EUT are reported. FCC Rule Measurement Required Result 15.107(a) Conducted Emission Measurement Passed by 6.60 dB 15.109(a) Radiated Emission Measurement (Below 1 GHz) Passed by 9.30 dB 15.109(a) Radiated Emission Measurement (Above 1 GHz) N/A * * The highest frequency of the internal sources of the EUT is less than 108 MHz. This test was measurement made up to 1 GHz according to the section 15.33 of FCC Part 15. The data collected shows that the HYUNDAI IBT CORP. / LCD MONITOR / L21C0FAL0 complied with technical requirements of above rules part 15.107(a) and 15.109(a) Class B Limits. The equipment is not modified anything, mechanical or circuits to improve EMI status during a measurement. No EMI suppression device(s) was added and/or modified during testing. Report no. ETLE130417.0397, Page 12 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 5.2 Conducted Emissions Measurement 5.2.1 Conducted Emissions Data EUT LCD MONITOR / L21C0FAL0 (S/N: N/A) Limit apply to FCC Part 15.107(a) Class B Test Date May 03, 2013 The EUT was connected as user’s guide. And during the executed test Operating Condition program for EMI program with "H" pattern display on monitor. (Worst case: VGA mode & USB mode) Result Passed by 6.60 dB Conducted Emission Test Data The following data and graph shows the highest levels of conducted emissions on both polarizations of hot and neutral line. Detector mode: CISPR Quasi-Peak mode (6 dB Bandwidth: 9 kHz) NOTES: 1. Please see the measured data and graph in next page. 2. The c.f value was included the antenna factor and cable loss. 3. Result value = Reading + c.f 4. Margin = Limit - Result 5. Measurement were performed at the AC Power Inlet in the frequency band of 150 kHz ~ 30 MHz according to the FCC Part 15.107(a) Class B. 6. If the average limit is met when using a Quasi-peak detector receiver, the EUT shall be deemed to meet both limits and measurement with the average detector receiver is unnecessary. Report no. ETLE130417.0397, Page 13 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 Line: HOT Report no. ETLE130417.0397, Page 14 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 Line: Neutral Report no. ETLE130417.0397, Page 15 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 5.3 Radiated Emissions Measurement 5.3.1 Radiated Emissions Data - Below 1 GHz EUT LCD MONITOR / L21C0FAL0 (S/N: N/A) Limit apply to FCC Part 15.109(a) Class B Test Date May 02, 2013 The EUT was connected as user’s guide. And during the executed test Operating Condition program for EMI program with "H" pattern display on monitor. (Worst case: VGA mode & USB mode) Result Passed by 9.30 dB Radiated Emission Test Data The following table shows the highest levels of radiated emissions on both polarizations of horizontal and vertical. Detector mode: CISPR Quasi-Peak mode (6 dB Bandwidth: 120 kHz) Frequency Reading Polarization Ant. Factor Cable Loss Result Limit Margin [MHz] [dB(μV)] (*H/**V) [dB/m] [dB(μV)] [dB(μV/m)] [dB(μV/m)] [dB] 40.90 17.01 V 11.91 1.38 30.30 40.00 9.70 53.18 17.06 V 12.21 1.43 30.70 40.00 9.30 120.67 18.24 V 11.30 1.86 31.40 43.50 12.10 177.94 13.85 V 11.69 2.16 27.70 43.50 15.80 296.53 11.51 H 13.21 2.68 27.40 46.00 18.60 NOTES: 1. * H : Horizontal polarization , ** V : Vertical polarization 2. Result = Reading + Antenna factor + Cable loss 3. Margin value = Limit - Result 4. The measurement was performed for the frequency range 30 MHz ~ 1 000 MHz according to the FCC Part 15.109(a) Class B. 5. The highest frequency of the internal sources of the EUT is less than 108 MHz. This test was measurement made up to 1 GHz according to the section 15.33 of FCC Part 15. Report no. ETLE130417.0397, Page 16 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 : Limit Quasi-peak Report no. ETLE130417.0397, Page 17 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 6. SAMPLE CALCULATION Sample Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor. The basic equation with a sample calculation is as follows: FS = RA + AF + CF - PA Where FS = Field Strength RA = Receiver Amplitude AF = Antenna Factor CF = Cable Attenuation Factor PA* = Preamplifier Factor * PA is only be used for the measuring frequency above 1 GHz. dB(μV) = 20 log10 (μV) : Equation dB(μV) = dBm + 107 Example : @ 53.18 MHz Class B Limit = 40.00 dB(μV/m) Reading = 17.06 dB(μV) Antenna Factor + Cable Loss = 12.21 + 1.43 = 13.64 dB(μV/m) Total = 30.70 dB(μV/m) Margin = 40.00 – 30.70 = 9.30 dB = 9.30 dB below Limit Report no. ETLE130417.0397, Page 18 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0

FCC TEST REPORT FCC ID: PJIL21C0FAL0 7. List of test equipments used for measurements Cal. Due Test Equipment Model Mfg. Serial No. Cal. Date Date EMI Test Receiver ESVS 10 R&S 835165/001 13.03.18 14.03.18 EMI Test Receiver ESPI3 R&S 100478 12.09.05 13.09.05 Two-Line V-Network ENV216 R&S 958599/106 13.03.19 14.03.19 LISN 3816-2 EMCO 1002 12.09.05 13.09.05 LogBicon Antenna VULB9160 Schwarzbeck 3128 12.02.22 14.02.22 Turn-Table TT 1.35 SI SES - N/A N/A Antenna Master AM 4.5 SES - N/A N/A Report no. ETLE130417.0397, Page 19 of 19 Head Office: # 371-51 Gasan-dong, Geumcheon-gu, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 ETLQP-21-F22-0


Document Created: 2019-11-11 05:45:21
Document Modified: 2019-11-11 05:45:21
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC