Test Report

FCC ID: PJIL17C0D081

Test Report

Download: PDF
FCCID_453424

HYUNDAI CALIBRATION & CERTIFICATION TECH. CO., LTD. Product Compliance Division, EMC Team SAN 136-1, AMI-RI , BUBAL-EUP, ICHEON-SI, KYOUNKI-DO, 467-701, KOREA TEL : +82 31 639 8518 FAX : +82 31 639 8525 CERTIFICATION (Permissive change class ) Manufacture; Date of Issue : July 16, 2004 HYUNDAI IMAGEQUEST CO., LTD. Test Report No.: HCT-F04-0715 SAN 136-1, AMI-RI , BUBAL-EUP, ICHEON-SI, KYOUNKI-DO, 467-701,KOREA Test Site: HYUNDAI CALIBRATION & CERTIFICATION TECHNOLOGIES CO., LTD. HYUNDAI IMAGEQUEST FRN : 0005-8664-39 HCT FRN : 0005-8664-21 FCC ID : PJIL17C0D081 MODEL / TYPE : Q17/L17C0D081 Rule Part(s): Part 15 & 2; ET Docket 95-19 Equipment Class: FCC Class B Peripheral Device (JBP) Standard(s): FCC Class B: (CISPR 22) EUT Type: 17” LCD Monitor Max. Resolution(s): Analog:1280 X 1024(@80.0KHz/75Hz), Digital: 1280 X 1024(@63.9KHz/60Hz) Model(s): Q17 Port/Connector(s) 15-pin D-sub VGA, 20-pin DVI-D (Digital RGB) connector, AUDIO IN/OUT, USB Upload/Download. LCD Panel Samsung Electronics (LTM170EU-L11) This equipment has been shown to be in compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.4-2001. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Report prepared by : Ki-Soo Kim Manager of EMC Tech. Part HYUNDAI CALIBRATION & CERTIFICATION TECH. CO., LTD. 1/19

FCC ID : PJIL17C0D081 TABLE OF CONTENTS PAGE REPORT COVER 1 TABLE OF CONTENTS 2 1.1 SCOPE 3 2.1 INTRODUCTION (SITE DESCRIPTION) 4 3.1 PRODUCTION INFORMATION 5-6 4.1 DESCRIPTION OF TESTS (CONDUCTED) 7 4.3 DESCRIPTION OF TESTS (RADIATED) 8 5.1 LIST OF SUPPORT EQUIPMENT 9-10 6.1 TEST DATA (CONDUCTED) 11-15 7.1 TEST DATA (RADIATED) 16 8.1 SAMPLE CALCULATIONS 17 9.1 TEST EQUIPMENT 18 10.1 TEST SOFTWARE USED 19 11.1 CONCLUSION 20 ATTACHMENT A: FCC ID LABEL & LOCATION ATTACHMENT B: EXTERNAL PHOTOGRAPHS ATTACHMENT C: BLOCK DIAGRAM(S) ATTACHMENT D: TEST SETUP PHOTOGRAPHS ATTACHMENT E: USER’S MANUAL ATTACHMENT F-1: INTERNAL PHOTOGRAPHS ATTACHMENT F-2: INTERNAL PHOTOGRAPHS REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 2/20

FCC ID : PJIL17C0D081 MEASUREMENT REPORT 1.1 Scope Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission. Applicant Name: HYUNDAI IMAGEQUEST Address: SAN 136-1, AMI-RI , BUBAL-EUP, ICHEON-SI, KYOUNKI-DO, 467-701,KOREA • FCC ID : PJIL17COD081 • Equipment Class: FCC Class B Peripheral Device (JBP) • EUT Type: 17” LCD MONITOR • Model(s): Q17 • LCD Panel: Samsung Electronics (LTM170EU-L11) • Max. Resolution: Analog:1280 X 1024(@80.0KHz/75Hz), Digital: 1280 X 1024(@63.9KHz/60Hz) • Frequency Range: V-Sync: 56Hz – 75Hz , H-Sync: 31KHz – 80KHz • Cable(s): Shielded D-Sub (with ferrite on both ends), Shielded DVI-D (with ferrite on both ends) Shielded USB (with ferrite on both ends), Shielded AUDIO (with ferrite on both ends) • Power Cord: Unshielded • Rule Part(s): FCC Part 15 Subpart B • Test Procedure(s): ANSI C63.4 (2001) • Dates of Tests: June 21, 2004 ~ June 28, 2004 • Place of Tests: 254-1,MAEKOK-RI, HOBUP-MYUN, ICHON-SI,KYOUNGKI-DO,467-701,KOREA REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 3/20

FCC ID : PJIL17C0D081 2.1 INTRODUCTION The measurement procedure described in American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9kHz to 40GHz (ANSIC63.4-2001) was used in determining radiated and conducted emissions emanating from HYUNDAI IMAGEQUEST CO.,LTD. 17-inch LCD Monitor FCC ID: PJIL17COD081 The open area test site and conducted measurement facility used to collect the radiated data are located at the 254-1, MAEKOK-RI,HOBUP-MYUN,ICHON-SI,KYOUNGKI-DO, 467-701,KOREA. The site is constructed in conformance with the requirements of ANSI C63.4and CISPR Publication 22. Detailed description of test facility was submitted to the Commission and accepted dated July 23, 2003 (Confirmation Number: EA90661) REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 4/20

FCC ID : PJIL17C0D081 3.1 PRODUCT INFORMATION 3.2 Equipment Description Equipment Under Test (EUT) is the HYUNDAI IMAGEQUEST CO.,Ltd. ( Model : Q17 ) 17-inch LCD Monitor FCC ID: : PJIL17COD081 Maximum Resolution(s): Analog:1280 X 1024(@80.0KHz/75Hz), Digital: 1280 X 1024(@63.9KHz/60Hz) Frequency Range(s): H-Sync: 31KHz – 80KHz V-Sync: 56Hz – 75 Hz Pixel Pitch: 0.264mm Power Supply: AC 100-240V 50/ 60Hz 1.0A Power Cord: Unshielded AC power cord Port(s)/Input Connector(s): 15-pin D-sub VGA connector, 20-pin DVI-D connector, AUDIO IN/OUT, USB Upload/Download. Cable(s): Shielded D-Sub (with ferrite on both ends), Shielded DVI-D (with ferrite on both ends) Shielded USB (with ferrite on both ends), Shielded AUDIO (with ferrite on both ends) Dimensions (W×H×D): 396×414×200mm(W×H×D) Weight (Net): 4.8Kg unpacked EMI Suppression Devices: Please refer to next page of the photographs for Solution for EMI REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 5/20

FCC ID : PJIL17C0D081 1. Apply a ferrite Core to the Power Cable 2. Attach a aluminum foil between Main Frame and LCD panel 3. Attach a gasket to stand connector REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 6/20

FCC ID : PJIL17C0D081 4.1 Description of Tests(Conducted) 4.2 Powerline Conducted RFI (150kHz- 30MHz) The power line conducted RFI measurements were performed according to CISPR 22. The EUT was placed on a non-conducting 1.0 by 1.5 meter table which is 0.8 meters in height and 0.40 meters away from the vertical wall of the shielded enclosure. Power to the EUT is provided through a Rohde & Schwarz 50 Ω / 50 uH Line Impedance Stabilization Network (LISN) and the support equipment through a separate Solar 50 Ω / 50 uH Line- Conducted Test Facility LISN. Sufficient time for the EUT, support equipment, and test equipment were allowed in order for them to warm up to their normal operating condition. The RF output of the LISN was connected to the spectrum analyzer to determine the frequency producing the maximum EME. The spectrum was scanned from 150kHz to 30 MHz. Each maximum EME was remeasured using an EMI receiver. The detector function of the receiver was set to CISPR quasi- peak and average mode with the bandwidth set to 9 kHz. Each emission was maximized consistent with the typical applications by varying the configuration of the test sample. Interface cables were connected to the available interface ports of the test unit. The effect of varying the position of cables was investigated to find the configuration that produces maximum Diagram emission. Excess cable lengths were bundled at the centre with 30- 40cm. in length. The worst-case configuration is noted in the test report and the photographs are attached. Each EME reported was calibrated using the Rohde & Schwarz SMX signal generator and are listed on Table 1. RFI Conducted FCC Class B FCC CLASS B CISPR 22 CLASS B RFI CONDUCTED Limits dB(uV/m) Limits dB(uV/m) FCC Class B CISPR 22 CISPR 22 Freq. Range Quasi-Peak Quasi-Peak Average 150kHz - 0.5MHz 48* 66-56** 56-46** 0.5MHz - 5MHz 48 56 46 5MHz - 30MHz 48 60 50 *FCC Class B limits starts from 450kHz **Limits decreases linearly with the logarithm of frequency Table 1. RFI Conducted Limits REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 7/20

FCC ID : PJIL17C0D081 4.3 Description of Tests(Radiated) Radiated Emissions Preliminary measurements were made indoors at 1 meter using broadband antennas, broadband amplifier, and spectrum analyzer to determine the frequency producing the maximum EME. Appropriate precaution was taken to ensure that all EME from the EUT were maximized and investigated. The spectrum was scanned from 30 to 300 MHz using biconical antenna, 300 to 1000 MHz using log- periodic antenna, and above 1 GHz using linearly polarized horn antennas. Final measurements were made outdoors at 10-meter test range using Dipole antennas and EMI receiver. For frequencies above 1 GHz, horn antennas were used. Sufficient time for the EUT, support equipment, and test equipment were allowed in order for them to warm up to their normal operating condition. The EMI receiver detector function was set to CISPR quasi-peak mode and the bandwidth of the receiver was set to 120 kHz. The EUT, support equipment, and interconnecting cables were arranged to the configuration that produces the maximum EME emission found during preliminary scan. The turntable containing the system was rotated; the antenna height was varied 1 to 4 meters and stopped at the azimuth or height producing the maximum emission. Horizontal and vertical antenna polarizations were checked. Each emission was maximized by: varying the mode of operation or resolution; clock or data exchange speed; scrolling H pattern to the EUT and/ or support equipment, and powering the monitor the computer aux AC outlet, if applicable; and changing the polarity of the antenna, whichever determined the worst-case emission. ITE Radiated Limits Frequency FCC Limit @ FCC Limit @ CISPR Limit @ (MHz) 3m. Quasi- 10m.* Quasi – 10m. Quasi-Peak Peak dB[µV/m] Peak dB [µV/m] dB [µV/m] 30-88 40.0 29.5 30.0 88-216 43.5 33.0 30.0 216-230 46.0 35.6 30.0 230-960 46.0 35.6 37.0 960-1000 54.0 43.5 37.0 > 1000 54.0 43.5 No Specified Limit * Limit extrapolated 20 dB/decade Table 2. Radiated Class B limits @ 10-meters REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 8/20

FCC ID : PJIL17C0D081 5.1 Support Equipment Used DEVICE TYPE MANUFACTURER MODEL NUMBER FCC ID / DoC CONNECTED TO HYUNDAI MONITOR (EUT) IMAGEQUEST Q17 PJIL17COD081 P.C CO., LTD. P.C H.P HP Pavilion 8921 DoC N/A KEY BOARD H.P 5181 DoC P.C MOUSE Microsoft IntelliMouse(PS/2) DoC P.C PRINTER H/P C4569A DoC P.C SERIAL MOUSE LOGITECH M-M28 DoC P.C USB MOUSE Microsoft IntelliMouse(USB) DoC EUT HEADSET T-SOUND CAS08 DoC EUT REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 9/20

FCC ID : PJIL17C0D081 5.2 Cable Description Power Cord I/O Cable Shielded Length (M) Shielded (Y/N) (Y/N) MONITOR(EUT) N Y 1.8(P), 1.8(D) PC(HOST) N N/A 1.8(P) KEY BOARD N/A Y 1.8(D) MOUSE N/A Y 1.8(D) PRINTER N Y 1.8(P),1.8(D) SERIAL MOUSE N/A Y 1.8(D) USB UPLOAD N/A Y 1.8(D) USB MOUSE N/A Y 1.8(D) AUDIO IN N/A Y 1.8(D) HEADSET N/A Y 1.8(D) The marked "(D)" means the Data Cable and "(P)" means the Power Cable. 5.3 Noise Suppression Parts on Cable. (I/O CABLE) Ferrite Bead Metal Hood Location Location (Y/N) (Y/N) MONITOR(EUT) Y BOTH END Y BOTH END KEY BOARD N N/A Y P.C END MOUSE Y P.C END Y P.C END PRINTER N N/A Y BOTH END SERIAL MOUSE N N/A Y EUT END USB UPLOAD Y BOTH END Y BOTH END USB MOUSE Y EUT END Y EUT END AUDIO IN Y BOTH END N N/A HEADSET N N/A N N/A REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 10/20

HCT Citaton Tenoogecontrion ca us: \ Bcz EMC TESTING Laboratory onr Manufacturer: ayumbat rmaceourst co., L. Operating Condition: 1280 X1024 75iz Test Site: Shield Room Operator: ks, tm Test Specification: CISPR 22 CLASS B Comment: a SCAN TABLE: "CISPR 22 Voltage ' Short Description: CiSPR 22 Voltage Start Stop Step Detector Meas. re Transducer Frequency Frequency Width Time Bandw. 150.0 kitr 500.0 kiz 5.0 khz MaxPeak 10.0 ms 9 kiz None Average 00.0 kiz 5.0 iz 5.0 kiz MaxPeak 10.0 ms 9 kHiz None Average 5.0 mite 30.0 vite 5.0 kiz MaxPeak 10.0 ms 9 kHiz None Average tevel. [amyv) so ; 10 so 7 so «0 ao z0 ak. rook some nook in rrequency. (ne] somes ol fin or +o ces CLCEin Ay wes G17 pre o mes ot? pro Y ——une cropa 2s v ge Volsage 9P Lings raw crapn v av Yolzage A¥ Lintz MEASUREMENT RESULT: "Q17_fin QP" 6/24/04 21:03mm — Frequency Level Transd Linit Margin Line PE w dBay ds aBay an 0205000 46.00 10.1 63 7k a 0.310000 38.50 10.1 60 2115 1 0410000 31.70 10.1 se 2s.0 1 3.615000 34.90 10.2 56 $11 4 4.025000 35.40 10.3 56 20.6 1 4130000 36.20 10.3 56 19.8 1 6.400000 35.70 10.3 so 24.3 1 6.505000 36.60 10.3 s0 a3.4 1 7.020000 35.70 10.3 eo 24.3 1 Rage 1/2 6/24/04 11:03mM 017

MEASUREMENT RESULT: "O17_fin AV" 6/24/04 ogam ~ Frequency bimit margin Milz dBpy de 0205000 53 17.9 eeeeenene e 0. 310000 18.7 0. 110000 212 3.510000 13.3 4.025000 13.7 4.130000 13.3 s.400000 17.1 6.505000 17.0 7.020000 17.5 Page 272 6/24/04

HCT Citaton contrion feovomiece Hcr EMC TESTING Laboratory sur: o17 HManufacturer: yuwbar rmmceoumst co., uro. Operating Condition: 1280 x1024 75%z Test Site: Shield Room Operator: xs, krm Test Specification: cisrr 22 cuass s Conment : n SCAN TABLE: "CISPR 22 Voltage" Short Description: C1SPR 22 voltage Start Stop Step Detector teas. tr Transducer Frequency Frequency Width Time Bandw. 150.0 kiz 500.0 kiz 5.0 kiz MaxPeak 10.0 ms 9 kiz None Average 00.0 knz 5.0 mz 5.0 kite MaxPeak 10.0 ms 9 kiz None Average 5.0 Mitz 30.0 Mz 5.0 kiz MaxPeak 10.0 ms 9 kitz None Average tever. aspy) o 150% 5oo aoox sook aoo% a an m zon rrequency (1e) sues qrz_cin or o120rin ay 917pro t 7 pre ay exsen 23 v oo vorrage of tinte cxSex 25 v ay voitage Ay timit MEASI T RESULT: "Q17 fin QP" 6/24/04 11:i3am — Prequency Level Transd Limit Margin Line PR wiz dBuy an aBpv as «205000 a4.00 10.1 63 r0.4 a 310000 34. 40 10.1 so w58 1 375000 30.20 10.1 se 26.10 1 130000 32.90 10.3 56 B4 i w235000 33. 40 10.3 56 22.6 1 «250000 34.80 10.3 56 ane a «655000 40.30 10.5 so 19.7 i .865000 39. 90 20.5 60 20.10 1 . 070000 39. 80 10.5 so 20.2 1 Page 1/2 6/24/04 11:13MM Q17

MERSUREMENT RESULT: "O17_fin AV" 6/24/04 11:13am — Frequency Level ‘transd Limit Margin Line PB e dBny ds dbuy as 0.205000 32. 60 10.1 s3 20.8 1 0.310000 22.70 10.1 so ML4 i 0. 415000 2 10.1 a8 215 1 a.235000 10.3 16 18.5 1 4.150000 10.3 46 1940 d 4.855000 10.3 16 18.0 1 24.680000 10.6 so 8270 a 24.925000 10.6 so i7.s0 a 25.195000 10.6 so 18.5 1 Page 2/2 6/24/04 ri:l3n 017

FCC ID : PJIL17C0D081 NOTES: 1. All modes of operation were investigated and the worst-case emissions are reported. 2. The CISPR RFI conducted limits are listed on Table 1 (Page7). 3. Line H = Hot, Line N = Neutral ** Measurements using CISPR quasi-peak mode. REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 15/20

FCC ID : PJIL17C0D081 7.1 RADIATED TEST DATA Frequency Reading Ant. Factor Cable Loss ANT POL Total Limit Margin MHz dBuV dB dB (H/V) dBuV/m dBuV/m dB 40.5 6.1 15.0 1.3 V 22.4 30 -7.6 94.6 11.6 9.3 2.2 H 23.1 30 -6.9 114.5 8.9 12.2 2.4 H 23.5 30 -6.5 152.9 6.8 15.1 2.7 V 24.6 30 -5.4 162.2 5.7 15.5 2.9 V 24.1 30 -5.9 199.7 4.9 16.2 3.2 V 24.3 30 -5.7 270.4 11.4 18.0 3.8 V 33.2 37 -3.8 298.1 8.8 19.6 4.0 V 32.4 37 -4.6 363.6 11.2 16.6 4.4 V 32.2 37 -4.8 397.6 11.9 16.9 4.6 H 33.4 37 -3.6 457.9 10.2 18.5 4.9 H 33.6 37 -3.4 Radiated Measurements at 10-meters. Analog mode: 1280 X 1024 (@80.0KHz/ 75Hz) NOTES: 1. All modes of operation were investigated, and the worst-case emissions are reported. 2. The radiated limits are listed on Table 2 (Page 8). ** AFCL = Antenna Factor (Roberts dipole) and Cable Loss . *** Measurements using CISPR quasi-peak mode. Above 1GHz, peak detector function mode is used using a resolution bandwidth of 1MHz and a video bandwidth of 1MHz. The peak level complies with the average limit. Peak mode is used with linearly polarized horn antenna and low-loss microwave cable. REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 16/20

FCC ID : PJIL17C0D081 8.1 Sample Calculations dB = 20 log 10 (mV/m) 8.2 Example 1: @ 0.205 MHz Class B limit = 63.4 dBµV Reading = 46.0 dBµV (calibrated level) Margin = 46.0 – 63.4= - 17.4 = 17.4 dB below limit 8.3 Example 2: @ 457.9 MHz Class B limit = 37.0 dBµV/m Reading = 10.2 dBµV/m (calibrated level) Antenna Factor + Cable Loss = 23.4 dB Total = 33.6dBµV/m Margin = 33.6- 37.0 = - 3.4 = 3.4 dB below limit REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 17/20

FCC ID : PJIL17C0D081 9.1 Test Equipment Type Manufacture Model Number CAL Date EMI Test Receiver Rohde & Schwarz ESI40 2003.11.16 EMI Test Receiver Rohde & Schwarz ESVS30 2003.07.15 LISN Rohde & Schwarz ESH2-Z5 2003.08.21 LISN EMCO ESH3-Z5 2003.11.12 Amplifier Hewlett-Packard 8447E 2004.04.26 Dipole Antennas Schwarzbeck VHAP 2004.04.08 Dipole Antennas Schwarzbeck UHAP 2004.04.08 TRILOG Antenna Schwarzbeck 9160 2004.04.06 Antenna Position Tower HD MA240 N/A Turn Table EMCO 1050 N/A Power Analyzer Voltech PM 3300 2004.04.02 Reference Network Impedance Voltech IEC 555 N/A AC Power Source PACIFIC Magnetic Module N/A AC Power Source PACIFIC 360-AMX 2003.12.10 Controller HD GmbH HD 100 N/A SlideBar HD GmbH KMS 560 N/A REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 18/20

FCC ID : PJIL17C0D081 10.1 Test Software Used The EUT exercise program used during radiated and conducted testing was designed to exercise the various system components in a manner similar to a typical use. The software, contained on a 3-1/2 inch disc, was inserted into drive A and is auto starting on power-up. Once loaded, the program sequentially exercises each system component in turn. The sequence used is :(1) Display test, (2) RS 232 test (3) Key board test,(4) Printer test,(5) FDD test,(6) HDD test. The complete cycle takes about 20 seconds and is repeated continuously. As the keyboard and mouse are strictly input devices, no data is transmitted to them during test. They are however, continuously scanned for data input activity. The video resolution modes setup and change program was used during the radiated and conducted emission testing. NOTE: This is a sample of the basic program used during the test. However, during testing, a different software program may be used; whichever determines the worst-case condition. In addition, the program used also depends on the number and type of devices being tested. Actual program used is the “H” pattern in Notepad under Windows environment. All resolution modes (1280×1024, 1152×870, 1024×768, 832×624, 800×600, 640x480, 720x400 ) were investigated and tested REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 19/20

FCC ID : PJIL17C0D081 11.1 Conclusion The data collected shows that the HYUNDAI IMAGEQUEST CO., LTD. 17-inch LCD Monitor FCC ID: PJIL17COD081 complies with §15.107 and §15.109 of the FCC Rules. REPORT NO. : HCT-F04-0715 HYUNDAI C–TECH 20/20


Document Created: 2004-07-26 19:47:15
Document Modified: 2004-07-26 19:47:15
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC