Test Report 1

FCC ID: PIYP3494-09A2T

Test Report

Download: PDF
FCCID_1099415

TEST REPORT Report No. : AL010174-001 Date : 2009-04-21 Application No. : LL202500(9) Applicant : Mattel Asia Pacific Sourcing Ltd. 1301, South Tower, World Finance Center, Harbour City, Tsim Sha Tsui, Hong Kong. Sample Description : One (1) submitted sample(s) stated to be Barbie® Corvette® & Doll of Model No. P3494 Radio Frequency : 27.145MHz Transmitter Rating : 1 x 9V size battery No. of submitted sample : Three (3) piece(s) Date Received : 2009-03-13. Test Period : 2009-03-14 to 2009-03-23. Test Requested : FCC Part 15 Certification. Test Method : 47 CFR Part 15 (10-1-08 Edition) ANSI C63.4 – 2003 Test Result : See attached sheet(s) from page 2 to 11. Conclusion : The submitted sample was found to comply with requirement of FCC Part 15 Subpart C. For and on behalf of CMA Industrial Development Foundation Limited Authorized Signature : ____________________________________________________ Mr. Wong Lap-pong, Andrew Assistant Manager Electrical Division Page 1 of 11 FCC ID: PIYP3494-09A2T This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AL010174-001 Date : 2009-04-21 Table of Contents 1 General Information.............................................................................................................................3 1.1 General Description .....................................................................................................................3 1.2 Location of the test site................................................................................................................4 1.3 List of measuring equipment .......................................................................................................5 2 Description of the radiated emission test.............................................................................................6 2.1 Test Procedure .............................................................................................................................6 2.2 Test Result ...................................................................................................................................6 2.3 Radiated Emission Measurement Data........................................................................................7 3 Description of the Line-conducted Test ..............................................................................................8 3.1 Test Procedure .............................................................................................................................8 3.2 Test Result ...................................................................................................................................8 3.3 Graph and Table of Conducted Emission Measurement Data ....................................................8 4 Photograph...........................................................................................................................................9 4.1 Photographs of the Test Setup for Radiated Emission and Conducted Emission .......................9 4.2 Photographs of the External and Internal Configurations of the EUT ........................................9 5 Supplementary document ..................................................................................................................10 5.1 Bandwidth..................................................................................................................................10 5.2 Duty cycle ..................................................................................................................................10 5.3 Transmission time......................................................................................................................10 6 Appendices ........................................................................................................................................11 Page 2 of 11 FCC ID: PIYP3494-09A2T This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AL010174-001 Date : 2009-04-21 1 General Information 1.1 General Description The equipment under test (EUT) is a transmitter for Barbie® Corvette® & Doll. It operates at 27.145MHz and the oscillation of radio control is generated by a crystal. The EUT is powered by 1 x 9V size battery. There are two buttons on the EUT. When the forward or backward button is pressed, it will transmit different radio control signal to the receiver. The antenna is permanently attached in EUT and the radio output power is unable to adjust. The brief circuit description is listed as follows: - Q1, Q2 and associated circuit act as an encoder. - Q3, Y1 and associated circuit act as an oscillator. Page 3 of 11 FCC ID: PIYP3494-09A2T This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AL010174-001 Date : 2009-04-21 1.2 Location of the test site Radiated emissions measurements are investigated and taken pursuant to the procedures of ANSI C63.4 – 2003. A Semi-Anechoic Chamber Testing Site is set up for investigation and located at: Ground Floor, Yan Hing Centre, 9 – 13 Wong Chuk Yeung Street, Fo Tan, Shatin, New Territories, Hong Kong. Conducted emissions measurements are investigated and also taken pursuant to the procedures of ANSI C63.4 – 2003. A shielded room is located at : Ground Floor, Yan Hing Centre, 9 – 13 Wong Chuk Yeung Street, Fo Tan, Shatin, New Territories, Hong Kong. Page 4 of 11 FCC ID: PIYP3494-09A2T This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AL010174-001 Date : 2009-04-21 1.3 List of measuring equipment Equipment Manufacturer Model No. Serial No. Calibration Due Date EMI Test Receiver R&S ESCI 100152 2009 December 02 Bilog Antenna Schaffner CBL6112B 2718 2010 August 04 Loop Antenna EMCO 6502 00056620 2009 July 18 Page 5 of 11 FCC ID: PIYP3494-09A2T This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AL010174-001 Date : 2009-04-21 2 Description of the radiated emission test 2.1 Test Procedure Radiated emissions measurements are investigated and taken pursuant to the procedures of ANSI C63.4 – 2003. The equipment under test (EUT) was placed on a non-conductive turntable with dimensions of 1.5m x 1m and 0.8m high above the ground. 3m from the EUT, a broadband antenna mounting on the mast received the signal strength. The turntable was rotated to maximize the emission level. The antenna was then moving along the mast from 1m up to 4m until no more higher value was found. Both horizontal and vertical polarization of the antenna were placed and investigated. For below 30MHz, a loop antenna with its vertical plane is placed 3m from the EUT and rotated about its vertical axis for maximum response at each azimuth about the EUT. And the centre of the loop shall be 1 m above the ground. The device was rotated through three orthogonal axes to determine which attitude and configuration produce the highest emission during measurement. 2.2 Test Result Peak Detector data was measured unless otherwise stated. “#” means emissions appearing within the restricted bands shall follow the requirement of section 15.205. The frequencies from fundamental up to the tenth harmonics were investigated, and emissions more 20dB below limit were not reported. Thus, those highest emissions were presented in next page (section 2.3) It was found that the EUT meet the FCC requirement. Page 6 of 11 FCC ID: PIYP3494-09A2T This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AL010174-001 Date : 2009-04-21 2.3 Radiated Emission Measurement Data Radiated emission pursuant to the requirement of FCC Part 15 subpart C Frequency Polarity Reading at Antenna and Average Field Limit at 3m Margin (MHz) (H/V) 3m Cable factor Factor Strength (dBµV/m) (dB) (dBµV/m) (dB) (dB) (dBµV/m) 27.145 V 66.2 9.2 -5.4 70.0 80.0 -10.0 #135.713 H 14.8 12.6 - 27.4 43.5 -16.1 #244.236 H 18.4 10.3 - 28.7 46.0 -17.3 #271.356 H 15.3 14.1 - 29.4 46.0 -16.6 298.482 H 15.7 14.1 - 29.8 46.0 -16.2 #325.611 H 17.4 15.9 - 33.3 46.0 -12.7 352.735 H 19.8 15.9 - 35.7 46.0 -10.3 379.872 H 20.2 15.9 - 36.1 46.0 -9.9 434.244 H 14.7 19.4 - 34.1 46.0 -11.9 461.376 H 13.5 19.4 - 32.9 46.0 -13.1 Page 7 of 11 FCC ID: PIYP3494-09A2T This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AL010174-001 Date : 2009-04-21 3 Description of the Line-conducted Test 3.1 Test Procedure Conducted emissions measurements are investigated and also taken pursuant to the procedures of ANSI C63.4 – 2003. The EUT was setup as described in the procedures, and both lines were measured. 3.2 Test Result No measurement is required as the EUT is a battery-operated product. 3.3 Graph and Table of Conducted Emission Measurement Data Not Applicable Page 8 of 11 FCC ID: PIYP3494-09A2T This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AL010174-001 Date : 2009-04-21 4 Photograph 4.1 Photographs of the Test Setup for Radiated Emission and Conducted Emission For electronic filing, the photos are saved with filename TSup1.jpg to TSup2.jpg. 4.2 Photographs of the External and Internal Configurations of the EUT For electronic filing, the photos are saved with filename ExPho1.jpg to ExPho2.jpg and InPho1.jpg to InPho2.jpg. Page 9 of 11 FCC ID: PIYP3494-09A2T This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AL010174-001 Date : 2009-04-21 5 Supplementary document The following document were submitted by applicant, and for electronic filing, the document are saved with the following filenames: Document Filename ID Label/Location LabelSmp.jpg Block Diagram BlkDia.pdf Schematic Diagram Schem.pdf Users Manual UserMan.pdf Operational Description OpDes.pdf 5.1 Bandwidth The plot on saved in TestRpt2.pdf shows the fundamental emission is confined in the specified band. It also shows that the band edge met the 15.209 requirement at 26.9599 and 27.2801 MHz. 5.2 Duty cycle The duty cycle is simply the on-time divided by the period: The duration of one cycle = 1.13ms Effective period of the cycle = 0.61ms Duty Cycle = 0.61ms / 1.13ms = 0.54 Therefore, the average factor is found by 20 log10 0.54 = -5.4dB 5.3 Transmission time Not Applicable Page 10 of 11 FCC ID: PIYP3494-09A2T This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com

TEST REPORT Report No. : AL010174-001 Date : 2009-04-21 6 Appendices A1. Photos of the set-up of Radiated Emissions 1 page A2. Photos of External Configurations 1 page A3. Photos of Internal Configurations 1 page A4. ID Label/Location 1 page A5. Bandwidth Plot 1 page A6. Average Factor 1 page A7. Block Diagram 1 page A8. Schematics Diagram 1 page A9. User Manual 3 pages A10. Operation Description 1 page ***** End of Report ***** Page 11 of 11 FCC ID: PIYP3494-09A2T This document is issued subject to CMA Testing standard TEARMS AND CONDITIONS, and shall not be reproduced except in full or with written approval by CMA Testing. CMA Industrial Development Foundation Limited Room 1302, Yan Hing Centre, 9-13 Wong Chuk Yeung St.., Fo Tan, Shatin, Hong Kong. Tel: (852) 2698 8198 Fax: (852) 2695 4177 E-mail: info@cmatcl.com Web Site: http://www.cmatcl.com


Document Created: 2009-04-21 12:31:50
Document Modified: 2009-04-21 12:31:50
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC