Test Report

FCC ID: PH3DJ-500

Test Report

Download: PDF
FCCID_2247354

Report No.: AGC00589131103FE08 Page 1 of 27 FCC Part 15 Rules &RSS­215 Test Report Report No.: AGC00589131103FE08 FCC ID : PH3DJ‐500 IC : 3070C‐DJ500 TYPE OF AUTHORIZATION : Certification APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : VHF/UHF FM HANDHELD TRANSCEIVER BRAND NAME : ALINCO TEST MODEL : DJ‐500T CLIENT : Alinco Incorporated, Electronics Division DATE OF ISSUE : Nov.14, 2013 STANDARD(S) : FCC Part 15 Rules&RSS‐215 REPORT VERSION : V 1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context.

Report No.: AGC00589131103FE08 Page 2 of 27 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Nov.14, 2013 Valid Original Report

Report No.: AGC00589131103FE08 Page 3 of 27 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE .................................................................................................4 2. PRODUCT INFORMATION ............................................................................................................5 3. TEST FACILITY ............................................................................................................................6 4. SUPPORT EQUIPMENT LIST ........................................................................................................7 5. SYSTEM DESCRIPTION................................................................................................................7 6 SUMMARY OF TEST RESULTS ......................................................................................................8 7. FCC LINE CONDUCTED EMISSION TEST ......................................................................................9 7.1. TEST EQUIPMENT OF LINE CONDUCTED EMISSION TEST .......................................................... 9 7.2 .LIMITS OF LINE CONDUCTED EMISSION TEST .............................................................................. 9 7.3. BLOCK DIAGRAM OF LINE CONDUCTED EMISSION TEST ............................................................ 9 7.4. PROCEDURE OF LINE CONDUCTED EMISSION TEST ................................................................. 10 7.5 TEST RESULT OF LINE CONDUCTED EMISSION TEST ................................................................ 11 8. FCC RADIATED EMISSION TEST ................................................................................................13 8.1. TEST EQUIPMENT OF RADIATED EMISSION ................................................................................ 13 8.2. LIMITS OF RADIATED EMISSION TEST .......................................................................................... 13 8.3 BLOCK DIAGRAM OF RADIATED EMISSION TEST......................................................................... 13 8.4 PROCEDURE OF RADIATED EMISSION TEST................................................................................ 14 8.5 TEST RESULT OF RADIATED EMISSION TEST .............................................................................. 15 APPENDIX 1..................................................................................................................................19 PHOTOGRAPHS OF TEST SETUP ..................................................................................................19 APPENDIX 2..................................................................................................................................20 PHOTOGRAPHS OF EUT ...............................................................................................................20

Report No.: AGC00589131103FE08 Page 4 of 27 1. VERIFICATION OF COMPLIANCE Applicant Alinco Incorporated, Electronics Division Address Yodoyabashi Dai-Bldg 13F, 4-4-9 Koraibashi, Chuo-Ku, Osaka 541-0043, Japan Manufacturer Alinco Incorporated, Electronics Division Address Yodoyabashi Dai-Bldg 13F, 4-4-9 Koraibashi, Chuo-Ku, Osaka 541-0043, Japan Product Designation VHF/UHF FM HANDHELD TRANSCEIVER Brand name: ALINCO Test Model DJ-500T Hardware Version: V1.0 Software Version: V2.02 Measurement Procedure ANSI C63.4: 2003 Date of test: Nov.11, 2013 to Nov.13, 2013 Deviation: None Condition of Test Sample Normal The above equipment was tested by Attestation Of Global Compliance (Shenzhen) Co., Ltd. for compliance with the requirements set forth in the FCC Rules and Regulations Part 15, the measurement procedure according to ANSI C63.4:2003. This said equipment in the configuration described in this report shows the maximum emission levels emanating from equipment are within the compliance requirements. The test results of this report relate only to the tested sample identified in this report. Tested by Wall Huang Nov.14, 2013 Checked By Kidd Yang Nov.14, 2013 Authorized By Solger Zhang Nov.14, 2013

Report No.: AGC00589131103FE08 Page 5 of 27 2. PRODUCT INFORMATION The EUT is a VHF/UHF FM HANDHELD TRANSCEIVER designed for voice communication. It is designed by way of utilizing the FM modulation achieves the system operating. A major technical description of EUT is described as following: Communication Type Voice / Tone only Modulation FM 144MHz-148MHz&420MHz-450 MHz RX Frequency Range 136MHz-174MHz &400MHz-480MHz Channel step 12.5KHz Antenna Designation Detachable Power Supply DC 7.4V by battery Input: 100-240V, 50/60HZ, 0.3A Adapter Parameter Output: 12V, 0.5A I/O Port Information ( Applicable Not Applicable) I/O Port of EUT I/O Port Type Q’TY Cable Tested with DC Input Port 1 1.5m, Unshielded Antenna Connect Port 1 0 1 Hand-Operated Microphone 1 0.5m, Unshielded 1 Connect Port

Report No.: AGC00589131103FE08 Page 6 of 27 3. TEST FACILITY Facility Attestation of Global Compliance (Shenzhen) Co., Ltd 2/F., Building 2, No.1-No.4, Chaxi Sanwei Technical Industrial Park, Gushu, Location: Xixiang, Bao'an District, Shenzhen, Guangdong, China The test site is constructed and calibrated to meet the FCC requirements in Description: documents ANSI C63.4:2003. Site Filing: The FCC Registration Number is 259865 All measuring equipment is in accord with ANSI C63.4 requirements that meet Instrument Tolerance: industry regulatory agency and accreditation agency requirement.

Report No.: AGC00589131103FE08 Page 7 of 27 4. SUPPORT EQUIPMENT LIST Device Type Manufacturer Model Name Serial No. Data Cable Power Cable -- -- -- -- -- -- 5. SYSTEM DESCRIPTION EUT test procedure: 1. Connect EUT and peripheral devices. 2. Power on the EUT, the EUT begins to work. 3. Running data transmission and make sure the EUT normal working. EMC TEST MODES No. TEST MODES 1 Scanning mode + Receiving mode Note: Only the result of the worst case was recorded in the report.

Report No.: AGC00589131103FE08 Page 8 of 27 6. SUMMARY OF TEST RESULTS FCC Rules RSS-215 Description Of Test Result §15.107 RSS-Gen Conduction Emission Compliant §15.109 RSS-Gen Radiated Emission Compliant Scanning receivers and frequency §15.121 §4.1 converters used with scanning receivers. Compliant

Report No.: AGC00589131103FE08 Page 9 of 27 7. FCC&RSS-215 LINE CONDUCTED EMISSION TEST 7.1. TEST EQUIPMENT OF LINE CONDUCTED EMISSION TEST Description Manufacturer Model Identifier Cal. Date Cal. Due Spectrum Analyzer Agilent E4440A US41421290 07/17/2013 07/16/2014 EMI Test Receiver Rohde & Schwarz ESCI 100694 07/17/2013 07/16/2014 LISN Rohde & Schwarz ESH2-Z5 862060/020 07/17/2013 07/16/2014 7.2 .LIMITS OF LINE CONDUCTED EMISSION TEST Maximum RF Line Voltage Frequency Q.P.( dBuV) Average( dBuV) 150kHz~500kHz 66-56 56-46 500kHz~5MHz 56 46 5MHz~30MHz 60 50 **Note: 1. The lower limit shall apply at the transition frequency. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50 MHz 7.3. BLOCK DIAGRAM OF LINE CONDUCTED EMISSION TEST S h ield ed R o o m F i lt e r 0 .4 m E U T To M e a s u r in g E q u ip m e n t 0 .8 m LIS N P o w er A : P ow er ed t h r o u g h f ilt e r

Report No.: AGC00589131103FE08 Page 10 of 27 7.4. PROCEDURE OF LINE CONDUCTED EMISSION TEST 1) The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.4 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. 2) Support equipment, if needed, was placed as per ANSI C63.4. 3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4. The EUT received power through a Line Impedance Stabilization Network (LISN) that was grounded to the protect earth. 4) The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 5) Analyzer / Receiver scanned from 150 kHz to 30MHz for emissions in each of the test modes. 6) During the above scans, the emissions were maximized by cable manipulation. 7) A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions. 8) Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. If EUT emission level was less –2dB to the A.V. limit in Peak mode, then the emission signal was re-checked using Q.P and Average detector. The test data of the worst case condition (mode 1) was reported on the following Data page.

Report No.: AGC00589131103FE08 Page 11 of 27 7.5 TEST RESULT OF LINE CONDUCTED EMISSION TEST Line Conducted Emission Test Line 1-L

Report No.: AGC00589131103FE08 Page 12 of 27 Line Conducted Emission Test Line 2-N

Report No.: AGC00589131103FE08 Page 13 of 27 8. FCC&RSS-215 RADIATED EMISSION TEST 8.1. TEST EQUIPMENT OF RADIATED EMISSION Description Manufacturer Model Identifier Cal. Date Cal. Due PSA SERIES AGILENT E4440A US41421290 07/17/2013 07/16/2014 SPECTRUM ANALYZER ANTENNA A.H. SAS-521-4 26 07/17/2013 07/16/2014 HORN ANTENNA EM EM-AH-10180 67 04/20/2013 04/19/2014 AMPLIFIER EM EM30180 0607030 07/18/2013 07/17/2014 POSITIONING MF MF-7802 MF780208147 07/17/2013 07/16/2014 CONTROLLER 8.2. LIMITS OF RADIATED EMISSION TEST PROVISIONS APPLICABLE FCC Part 15 Subpart B Section 15.109 RSS-215 Section 5.1 Frequency Distance Maximum Field Strength Limit (MHz) (m) (dBuV/m/ Q.P.) 30~88 3 40.0 88~216 3 43.5 216~960 3 46.0 Above 960 3 54.0 **Note: The lower limit shall apply at the transition frequency. 8.3 BLOCK DIAGRAM OF RADIATED EMISSION TEST 1-4m EUT 3m Amplifier 0.8 m Spectrum Analyzer

Report No.: AGC00589131103FE08 Page 14 of 27 8.4 PROCEDURE OF RADIATED EMISSION TEST 1) The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden turntable with a height of 0.8 meters is used which is placed on the ground plane as per ANSI C63.4 (see Test Facility for the dimensions of the ground plane used). When the EUT is floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. 2) Support equipment, if needed, was placed as per ANSI C63.4. 3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4. 4) The EUT received DC 7.4V by DC source. All support equipments received AC 120V/60Hz power from socket under the turntable, if any. 5) The antenna was placed at 3 meter away from the EUT as stated in FCC Part 15. The antenna connected to the Analyzer via a cable and at times a pre-amplifier would be used. 6) The Analyzer / Receiver quickly scanned from 30MHz to 1000MHz. The EUT test program was started. Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4 meters above the ground plane, in both the vertical and the horizontal polarization, to maximize the emission reading level. 7) The test mode(s) were scanned during the test: 8) Recorded at least the six highest emissions. Emission frequency, amplitude, antenna position, polarization and turntable position were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit and Q.P./Peak reading is presented. The test data of the worst case condition(mode 1) was reported on the following Data page

Report No.: AGC00589131103FE08 Page 15 of 27 8.5 TEST RESULT OF RADIATED EMISSION TEST Radiated Emission Test –Horizontal -3m Below 1G

Report No.: AGC00589131103FE08 Page 16 of 27 Radiated Emission Test –Vertical -3m Below 1G

Report No.: AGC00589131103FE08 Page 17 of 27 Radiated Emission Test –Horizontal -3m Above 1G

Report No.: AGC00589131103FE08 Page 18 of 27 Radiated Emission Test –Vertical -3m Above 1G

Report No.: AGC00589131103FE08 Page 19 of 27 APPENDIX 1 PHOTOGRAPHS OF TEST SETUP RADIATED TEST SETUP CONDUCTED EMISSION

Report No.: AGC00589131103FE08 Page 20 of 27 APPENDIX 2 PHOTOGRAPHS OF EUT WHOLE VIEW OF EUT TOP VIEW OF EUT

Report No.: AGC00589131103FE08 Page 21 of 27 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

Report No.: AGC00589131103FE08 Page 22 of 27 BACK VIEW OF EUT LEFT VIEW OF EUT

Report No.: AGC00589131103FE08 Page 23 of 27 RIGHT VIEW OF EUT OPEN VIEW-1 OF EUT

Report No.: AGC00589131103FE08 Page 24 of 27 OPEN VIEW-2 OF EUT INTERNAL VIEW-1 OF EUT

Report No.: AGC00589131103FE08 Page 25 of 27 INTERNAL VIEW-2 OF EUT INTERNAL VIEW-3 OF EUT

Report No.: AGC00589131103FE08 Page 26 of 27 INTERNAL VIEW-4 OF EUT INTERNAL VIEW-5 OF EUT

Report No.: AGC00589131103FE08 Page 27 of 27 INTERNAL VIEW-6 OF EUT INTERNAL VIEW-7 OF EUT ----END OF REPORT----


Document Created: 2014-04-22 11:40:44
Document Modified: 2014-04-22 11:40:44
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC