RF Exposure SAR Report 3

FCC ID: PD9AX200D2L

RF Exposure Info

Download: PDF
FCCID_4251325

Report Number: SAR.20190415 Appendix F – Phantom Calibration Data Sheets © 2019 RF Exposure Lab, LLC Page 241 of 243 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC.

Schmid & Partner Engineering AG e _2 Zeughausstrasse 43, 8004 Zurich, Switzerland Phone +41 44 245 9700, Fax +41 44 245 9779 info@speag.com, http. //www.speag.com Certificate of Conformity / First Article Inspection Item Oval Flat Phantom ELI 4.0 Type No QD OVA 001 B Series No 1003 and higher Manufacturer Untersee Composites Knebelstrasse 8 CH—8268 Mannenbach, Switzerland Tests Complete tests were made on the prototype units QD OVA 001 AA 1001, QD OVA 001 AB 1002, pre—series units QD OVA 001 BA 1003—1005 as weil as on the series units QD OVA 001 BB, 1006 ff. Test Requirement Details Units tested Material Compliant with the standard Bottom plate: all thickness requirements 2.0mm +/— 0.2mm Material Dielectric parameters for required < 6 GHz: Rel. permittivity = 4 Material parameters frequencies +/—1, Loss tangent < 0.05 sample Material The material has been tested to be DGBE based simulating Equivalent resistivity compatible with the liquids defined in liquids. phantoms, the standards if handled and cleaned Observe Technical Note for Material according to the instructions. material compatibility. sample Shape Thickness of botom material, Bottom elliptical 600 x 400 mm Prototypes, Internal dimensions, Depth 190 mm, Sample Sagging Shape is within tolerance for testing compatible with standards from filling height up to 155 mm, minimum frequency Eventual sagging is reduced or eliminated by support via DUT Standards [1] CENELEC EN 50361—2001, « Basic standard for the measurement of the Specific Absorption Rate related to human exposure to electromagnetic fields from mobile phones (300 MHz — 3 GHz) », July 2001 [2] IEEE 1528—2003, "Recommended Practice for Determining the Peak Spatial—Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques, December 2003 [3] IEC 62209 — 1, "Specific Absorption Rate (SAR) in the frequency range of 300 MHz to 3 GHz — Measurement Procedure, Part 1: Hand—held mobile wireless communication devices", February 2005 [4] IEC 62209 —— 2, Draft, "Human Exposure to Radio Frequency Fields from Handheld and Body— Mounted Wireless Communication Devices — Human models, Instrumentation and Procedures — Part 2: Procedure to determing the Specific Absorption Rate (SAR) in the head and body for 30 MHz to 6 GHz Handheld and Body—Mounted Devices used in close proximity to the Body.", February 2005 [8] OET Bulletin 65, Supplement C, "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields", Edition January 2001 Based on the tests above, we certify that this item is in compliance with the standards [1] to [5] if operated according to the specific requirements and considering the thickness. The dimensions are fully compliant with [4] from 30 MHz to 6 GHz. For the other standards, the minimum lower frequency limit is limited due to the dimensional requirements ([1]: 450 MHz, [2]: 300 MHz, [3]: 800 MHz, [5]:; 375 MHz) and possibly further by the dimensions of the DUT. § P 8 @ Schmid&&Partner Engineering AG Date 28.4.2008 Signature / Stamp Zeughaugétrasse 43,8004 Zurich, Switzectand Phone 441 44 245 9700, Fax +41,44,245 9779 info@gbeag.com; hitp//wwww.speag.com Doc No 881 —QD OVA 001 B— D Page 1 (1)

Report Number: SAR.20190415 Appendix G – Validation Summary Per FCC KDB 865664 D02 v01r02, SAR system validation status should be documented to confirm measurement accuracy. The SAR systems (including SAR probes, system components and software versions) used for this device were validated against its performance specifications prior to the SAR measurements. Reference dipoles were used with the required tissue equivalent media for system validation according to the procedures outlined in FCC KDB 865664 D01 v01r04 and IEEE 1528-2013. Since SAR probe calibrations are frequency dependent, each probe calibration point was validated at a frequency within the valid frequency range of the probe calibration point using the system that normally operates with the probe for routine SAR measurements and according to the required tissue equivalent media. A tabulated summary of the system validation status including the validation date(s), measurement frequencies, SAR probes and tissue dielectric parameters has been included. Table G-1 SAR System Validation Summary SAR CW Validation Modulation Validation Freq. Probe Probe Probe Cal. Cond. Perm. System Date Sens- Probe Probe Modulation Duty (MHz) S/N Type Point (σ) (ɛr) PAR # itivity Linearity Isotropy Type Factor 2 2450 5/03/2018 3693 EX3DV4 2450 Body 1.98 52.59 Pass Pass Pass OFDM/TDD Pass Pass 2 5250 5/02/2018 3693 EX3DV4 5200 Body 5.33 48.88 Pass Pass Pass OFDM N/A Pass 2 5600 5/02/2018 3693 EX3DV4 5600 Body 5.75 48.31 Pass Pass Pass OFDM N/A Pass 2 5750 5/02/2018 3693 EX3DV4 5800 Body 5.96 48.16 Pass Pass Pass OFDM N/A Pass 3 2450 1/28/2019 3833 EX3DV4 2450 Body 1.97 52.53 Pass Pass Pass OFDM/TDD Pass Pass 3 5250 1/28/2019 3833 EX3DV4 5200 Body 5.30 48.93 Pass Pass Pass OFDM N/A Pass 3 5600 1/29/2019 3833 EX3DV4 5600 Body 5.79 48.33 Pass Pass Pass OFDM N/A Pass 3 5750 1/29/2019 3833 EX3DV4 5800 Body 5.97 48.13 Pass Pass Pass OFDM N/A Pass 3 2450 4/12/2019 7530 EX3DV4 2450 Body 1.96 52.64 Pass Pass Pass OFDM/TDD Pass Pass 3 5250 4/11/2019 7530 EX3DV4 5200 Body 5.40 48.88 Pass Pass Pass OFDM N/A Pass 3 5600 4/11/2019 7530 EX3DV4 5600 Body 5.80 48.36 Pass Pass Pass OFDM N/A Pass 3 5750 4/11/2019 7530 EX3DV4 5800 Body 5.99 48.14 Pass Pass Pass OFDM N/A Pass © 2019 RF Exposure Lab, LLC Page 243 of 243 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC.


Document Created: 2019-04-25 17:53:59
Document Modified: 2019-04-25 17:53:59
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC