RF Exposure SAR Report 2

FCC ID: PD98265D2

RF Exposure Info

Download: PDF
FCCID_3893563

DASY5 Validation Report for Head TSL Date: 10.08.2015 Test Laboratory: SPEAG, Zurich, Switzerland _ DUT : Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 881 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 1.87 S$/m; & = 38.1; p = 1000 kg/m? Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: ES3DV3 — SN3205; ConvF(4.54, 4.54, 4.54); Calibrated: 30.12.2014; Sensor—Surface: 3mm (Mechanical Surface Detection) Electronics: DAF4 Sn601; Calibrated: 18.08.2014 Phantom: Flat Phantom 5.0 (front); Type: QDOOOP50A¥AA; Serial: 1001 DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 101.8 V/m; Power Drift = 0.02 dB Peak SAR (extrapolated) = 28.0 W/kg SAR(1 g) = 13.7 W/kg; SAR(10 g) = 6.43 W/kg Maximum value of SAR (measured) = 18.1 W/kg —10.00 —15.00 —20.00 —25.00 0 dB = 18.1 W/kg = 12.58 dBW/kg Certificate No: D2450V2—881_Aug15 Page 5 of 8

Impedance Measurement Plot for Head TSL 18 Aug 2015 15:18:07 EHM sii 4 uU ors 1154469 e RA4355 e 158.277 pH 2 450.000 @B@ MHz .e —. Del C& fi'u‘-a 16 H1 d CH2 Oe 1 Ca Ast :I.GEl H1d START 2 250.000 000 MHz STOFP 2 650,.000 0090 MHz Certificate No: D2450V2—881_Aug15 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 10.08.2015 Test Laboratory: SPEAG, Zurich, Switzerland _ DUT : Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 881 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 2.03 S/m; s = 50.6; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: ES3DV3 — SN3205; ConvF(4.32, 4.32, 4.32); Calibrated: 30.12.2014; Sensor—Surface: 3mm (Mechanical Surface Detection) Electronics: DAFA4 S$n601; Calibrated: 18.08.2014 Phantom: Flat Phantom 5.0 (back); Type: QDOOOP50AA; Serial: 1002 DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 96.26 V/m; Power Drift = —0.05 dB Peak SAR (extrapolated) = 27.7 W/kg A*% SAR(1 g) = 13.4 W/kg; SAR(10 g) = 6.27 W/kg Maximum value of SAR (measured) = 17.7 W/kg — —5.00 —10.00 —15.00 —20.00 —25.00 0 dB = 17.7 W/kg = 12.48 dBW/kg Certificate No: D2450V2—881_Aug15 Page 7 of 8

Impedance Measurement Plot for Body TSL | 10 fAug 2015 1§5:17:39 CHL s1ii 1 D FS 1: 50.879 2 4.4199 a 287.12 pH 2 450.000 000 MHz ——+——— De1 C& A*s 16 H1 d CH2Z Oe 1 Ca Aw 159 omm H1 d START 2 250.000 ado MHz STOP 2 6590.000 00o MHz Certificate No: D2450V2—881_Aug15 Page 8 of 8

9y a a \\\\u|u/,,, Callbl_'atlon Laboratory of i\“&////z} S Schweizerischer Kalibrierdienst Schmid & Partner ;'afi&% c Service suisse d‘étalonnage Englneerlng AG Tz //_-% > Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland > ///\\\ CS S swiss Calibration Service T Ahaluts® ® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client RF Exposure Lab Certificate No: D5GHzV2—1119_Aug15 CALIBRATION CERTIFICATE | Object DSGHzV2 — SN: 1119 Calibration procedure(s) QA CAL—22.v2 Calibration procedure for dipole validation kits between 3—6 GHz Calibration date: August 11, 2015 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (St1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration} Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter EPM—442A GB37480704 07—Oct—14 (No. 217—02020) Oct—15 Power sensor HP 8481A US37292783 07—Oct—14 (No. 217—02020) Oct—15 Power sensor HP 8481A MY41092317 07—Oct—14 (No. 217—02021) Oct—15 Reference 20 dB Attenuator SN: 5058 (20k) 01—Apr—15 (No. 217—02131) Mar—16 Type—N mismatch combination SN: 5047.2 / 06327 01—Apr—15 (No. 217—02134) Mar—16 Reference Probe EX3DV4 SN: 3503 30—Dec—14 (No. EX3—3503_Dec14) Dec—15 DAE4 SN: 601 18—Aug—14 (No. DAE4—601_Aug14) Aug—15 Secondary Standards ID # Check Date (in house) Scheduled Check RF generator R&S SMT—06 100005 04—Aug—99 (in house check Oct—13) In house check: Oct—16 Network Analyzer HP 8753E US37390585 $4206 18—Oct—01 (in house check Oct—14) In house check: Oct—15 Name Function Signature Calibrated by: Israe Elnaouq Laboratory Technician /)m WM Approved by: Katjia Pokovic Technical Manager issued: August 11, 2015 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: DSGHzV2—1119_Aug15 Page 1 of 16

Ca"b'_'atlon Laboratory of W7 i\\\\\fi—//@ S Schweizerischer Kalibrierdienst SChm!d & Eartner iia\es—/m’é C Service suisse d‘étalonnage Englneenng AG g. y y Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ~7 ///\\\ CS S gwiss Calibration Service * Abiluts® * Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,2z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) 1EC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 c) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1119_Aug15 Page 2 of 16

Measurement Conditions DASY system configuration, as far as not iven on page 1. DASY Version DASYS5 V52.8.8 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5200 MHz + 1 MHz 5300 MHz + 1 MHz Frequency 5500 MHz + 1 MHz 5600 MHz + 1 MHz 5800 MHz + 1 MHz Head TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.0 4.66 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.5 + 6 % 4.53 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.11 W/kg SAR for nominal Head TSL parameters normalized to 1W 80.8 W/ikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.32 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.1 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1119_Aug15 Page 3 of 16

Head TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.76 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.4 +6 % 4.63 mho/m + 6 % Head TSL temperature change during test <0.5 °C _——— ———— SAR result with Head TSL at 5300 MHz SAR averaged over 1 ecm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.46 W/kg SAR for nominal Head TSL parameters normalized to 1W 84.3 W / kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.42 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.1 Wikg + 19.5 % (k=2) Head TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.6 4.96 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 35.1 +6 % 4.82 mho/m + 6 % Head TSL temperature change during test <0.5 °C ———— SAR result with Head TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.50 W/kg SAR for nominal Head TSL parameters normalized to 1W 84.6 Wi/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.42 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.1 Wi/kg + 19.5 % (k=2) Certificate No: D5GHzV2—1119_Aug15 Page 4 of 16

Head TSL parameters at 5600 MHz The following parameters and calculations were applied. | Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 34.9 +6 % 4.93 mho/m + 6 % Head TSL temperature change during test <0.5 °C SAR result with Head) TSL at 5600 MHz SAR averaged over 1\em* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.46 Wikg SAR for nominal Head|TSL parameters normalized to 1W 84.2 Wi/ikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.41 Wikg SAR for nominal Head [TSL parameters normalized to 1W 24.0 Wikg + 19.5 % (k=2) Head TSL parameters) at 5800 MHz The following parameters| and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.3 5.27 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 34.7 +6 % 5.14 mho/m +6 % Head TSL temperature change during test <0.5 °C ———— SAR result with Head TSL at 5800 MHz SAR averaged over 1 ¢m* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.10 W/kg SAR for nominal Head TSL parameters normalized to 1W 80.6 W/kg + 19.9 % (k=2) SAR averaged over 10|cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.31 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.0 W/ikg + 19.5 % (k=2) Certificate No: DS5GHzV2—11 19_f\ug1 5 Page 5 of 16

Body TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 49.0 5.30 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 47.9 +6 % 5.43 mho/m +6 % Body TSL temperature change during test <0.5 °C ———— ———— SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.77 Wikg SAR for nominal Body TSL parameters normalized to 1W 77.4 Wikg x 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.17 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.6 W/kg + 19.5 % (k=2) Body TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.42 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 47.7 £ 6 % 5.56 mho/m +6 % Body TSL temperature change during test <0.5 °C SAR result with Body TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.79 W/kg SAR for nominal Body TSL parameters normalized to 1W 77.6 Wikg * 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.17 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.6 W/kg + 19.5 % (k=2) Certificate No: D5GHzV2—1119_Aug15 Page 6 of 16

Body TSL parameters at 5500 MHz The followingparameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.6 5.65 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 47.3 £6 % 5.82 mho/m + 6 % Body TSL temperature change during test <0.5 °C ———— ———— SAR result with Body TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 8.30 W/kGg SAR for nominal Body TSL parameters normalized to 1W 82.6 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.30 W/kg SAR for nominal Body TSL parameters normalized to 1W 22.9 Wikg + 19.5 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 47.2 £ 6 % 5.95 mho/m + 6 % Body TSL temperature change during test <0.5 °C ———— =——— SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 8.10 W/kg SAR for nominal Body TSL parameters normalized to 1W 80.7 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.25 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.4 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1119_Aug15 Page 7 of 16

Body TSL parameters at 5800 MHz The followingparameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.9 +6 % 6.23 mho/m +6 % Body TSL temperature change during test <0.5 °C a——— =——— SAR result with Body TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.91 W/kg SAR for nominal Body TSL parameters normalized to 1W 78.8 Wikg + 19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 100 mW input power 219 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.8 Wikg + 19.5 % (k=2) Extended Calibration Usage of SAR dipoles calibrated less than 3 years ago but more thaq 1 year ago were confirmed in maintaining return loss (< —20 dB, within 20% of prior calibration) d and impedance (within 5 ohm from prior calibration) requirements per extende calibrations in KDB Publication 865664 DO1 v01r04. D5GHzV2 SN: 1119 — Head Date Return Loss Impedance Frequency A% Measurement dB a 5200 MHz 5300 MHz 5500 MHz 5600 MHz 5800 MHz D5GHzV2 SN: 1119 — Body Return Loss Impedance Impedance Date A% Frequency I Measurement dB Real (Q 5200 MHz 5300 MHz 5500 MHz 5600 MHz 5800 MHz Certificate No DSGHzV2—1119 Auat5 Page 8 of 16

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 51.6 Q — 8.4 jQ Return Loss —21.5 dB Antenna Parameters with Head TSL at 5300 MHz Impedance, transformed to feed point 51.4 0 — 3.9jQ Return Loss — 27.8 dB Antenna Parameters with Head TSL at 5500 MHz Impedance, transformed to feed point 54.2 Q — 3.4 jQ Return Loss — 25.8 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 56.3 Q — 1.5 |Q Return Loss — 24.3 dB Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point 56.6 Q — 2.8 |Q Return Loss — 23.4 dB Antenna Parameters with Body TSL at 5200 MHz Impedance, transformed to feed point 51.6 Q — 7.2 jQ Return Loss — 22.8 dB Antenna Parameters with Body TSL at 5300 MHz Impedance, transformed to feed point 51.1 Q — 2.7 jQ Return Loss — 30.8 dB Antenna Parameters with Body TSL at 5500 MHz Impedance, transformed to feed point 54.3 Q — 1.3 jQ Return Loss — 27.4 dB Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 56.4 Q — 0.1 jQ Return Loss — 24.4 dB Certificate No: D5GHzV2—1119_Aug15 Page 9 of 16

Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point 57.5 Q — 0.9 jQ Return Loss — 23.1 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.206 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on September 08, 2011 Certificate No: D5GHzV2—1119_Aug15 Page 10 of 16

DASY5 Validation Report for Head TSL Date: 10.08.2015 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 5GHz; Type: D5GHzV2; Serial: DSGHzV2 — SN: 1119 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: £ = 5200 MHz; 0 = 4.53 S/m; &, = 35.5; p = 1000 kg/m" , Medium parameters used: f = 5300 MHz; 0 = 4.63 S/m;8, 35.4; p = 1000 kg/m* , Medium parameters used: f = 5500 MHz; 0 = 4.82 S/m; ar = 35.1; p = 1000 kg/m Medium parameters used: f = 5600 MHz; 0 = 4.93 S$/m; sr = 34.9; p = 1000 kg/m* , Medium parameters used: £ = 5800 MHz; 0 = 5.14 S/m; £; = 34.7; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(5.51, 5.51, 5.51); Calibrated: 30.12.2014, ConvF(5.21, 5.21, 5.21); Calibrated: 30.12.2014, ConvF(5.12, 5.12, 5.12); Calibrated: 30.12.2014, ConvF(4.92, 4.92, 4.92); Calibrated: 30.12.2014, ConvF(4.9, 4.9, 4.9); Calibrated: 30.12.2014; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAF4 Sn601; Calibrated: 18.08.2014 e Phantom: Flat Phantom 5.0 (front); Type: QDOOOP5OAA; Serial: 1001 e DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 66.84 V/m; Power Drift = —0.00 dB Peak SAR (extrapolated) = 29.5 W/kg SAR(1 g) =8.11 W/kg; SAR(10 g) = 2.32 W/kg Maximum value of SAR (measured) = 18.6 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.35 V/m; Power Drift = —0.03 dB Peak SAR (extrapolated) = 32.1 W/kg SAR(1 g) = 8.46 W/kg; SAR(10 g) = 2.42 W/kg Maximum value of SAR (measured) = 19.8 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1 4mm Reference Value = 66.30 V/m; Power Drift = —0.00 dB Peak SAR (extrapolated) = 33.6 W/kg SAR(1 g) = 8.5 W/kg; SAR(10 g) = 2.42 W/kg Maximum value of SAR (measured) = 20.2 W/kg Certificate No: D5GHzV2—1119_Aug15 Page 11 of 16

Dipole Calibration for Head Tissue/Pin=100mwW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4 , dz=1.4mm Reference Value = 65.73 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 33.5 W/kg SAR(I g) = 8.46 W/kg; SAR(10 g) = 2.41 W/kg ‘ Maximum value of SAR (measured) = 20.0 W/kg Dipole Calibration for Head Tissue/Pin=100mwW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4imm, dz=1.4mm Reference Value = 63.40 V/m; Power Drift = —0.00 dB Peak SAR (extrapolated) = 33.5 W/kg SAR(I g) = 8.1 W/kg; SAR(10 g) = 2.31 W/kg Maximum value of SAR (measured) = 19.7 W/kg —12.00 —18.00 —24.00 —30.00 0 dB = 18.6 W/kg = 12.70 dBW/kg Certificate No: D5GHzV2—1119_Aug15 Page 12 of 16

Impedance Measurement Plot for Head TSL 10 fAug 2015 14144108 CHI s1100 i uors 1: 51.607 o —B41i60 a 3.6367 pF 5 200.000 BM MH=z a e | CH1 Markers Del # §1.441 0 M ~2,8633 0 Cor ; * ‘ ‘ | foscse M odhuse "_3 4. o x ?.4 1 [/)| 3: $4,199 0 —3.397 4 & 4 * x & fi’o’g 16 ~ | | H1d | cH2 s41 Log _5 dB/REF —20 dB o 1:—21.510 dB_| _5 2@9.@9@}5@@ MHz _ Sgp, fL———4 + 4 cmeiiadese drommlhlilf sc 4 | CH2 Mark ers i — .4‘ .y,_‘._., ——_—_—__—_—g._.. .“ A..~~~z~llk + f + g/ Cor | | | [ | 5 a—27,.822 dB 530000 GHz _i fose...ccsesomennafpuesnsasronssmsfuiraounnssinsavuftisssinsnsnsisonsalfeosessssmnomrornofuecmmmmemmmemerofemcces | 4, wmmbdleldfecomtaifionce | ,,...4'...._.._...-...-4 | l 3—25.7 51 dB 5.50000 GHz } + | (\\ 1 4 | ~——37 | sfeas——4| o_A | l | | | m | | | 41—24.294 dB MEH Lrnmcsmmmmifprmmmmcmmmcihhs iesernnnlge 7 } i 4 P 5.60000 GHz . ,* n + gustics ukss Guiffereemmarecmmssmenifiiese rothisamms 4“..‘_.____1 S:—23.440 dB 5.850000 GHz H1d || + 4| +j 4{ +| + 4 4| || START 5 008.000adeMH= CC sToP 6 0ab.008 on MHz Certificate No: D5GHzV2—1119_Aug15 Page 13 of 16

DASY5 Validation Report for Body TSL Date: 11.08.2015 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 5GHz; Type: D5GHzV2; Serial: D5SGHzV2 — SN: 1119 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 0 = 5.43 S/m; &, = 47.9; p = 1000 kg/m" , Medium parameters used: £ = 5300 MHz; 0 = 5.56 S/m; & = 47.7; p = 1000 kg/m" , Medium parameters used: f = 5500 MHz; 0 = 5.82 S/m; sr 47.3; p = 1000 kg/m" , Medium parameters used: f = 5600 MHz; 5 = 5.95 S/m:; sr =47.2, p= 1000 kg/m* , Medium parameters used: f = 5800 MHz; 0 = 6.23 $/m; s, = 46.9; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(4.95, 4.95, 4.95); Calibrated: 30.12.2014, ConvF(4.78, 4.78, 4.78); Calibrated: 30.12.2014, ConvF(4.45, 4.45, 4.45); Calibrated: 30.12.2014, ConvF(4.35, 4.35, 4.35);, Calibrated: 30.12.2014, ConvF(4.32, 4.32, 4.32); Calibrated: 30.12.2014; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAEA4 Sn601; Calibrated: 18.08.2014 e Phantom: Flat Phantom 5.0 (back); Type: QDOOOP5OAA; Serial: 1002 e DASY52 52.8.8(1222); SEMCAD X 14.6.10(7331) Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 60.11 V/m;, Power Drift = 0.01 dB Peak SAR (extrapolated) = 30.4 W/kg SAR(I1 g) =7.77 W/kg; SAR(10 g) = 2.17 W/kg Maximum value of SAR (measured) = 18.1 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.89 V/m; Power Drift = —0.01 dB Peak SAR (extrapolated) = 31.4 W/kg SAR(1 g) =7.79 W/kg; SAR(10 g) = 2.17 W/kg Maximum value of SAR (measured) = 18.3 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 60.26 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 35.5 W/kg SAR(1 g) = 8.3 W/kg; SAR(10 g) = 2.3 W/kg Maximum value of SAR (measured) = 19.9 W/kg Certificate No: D5GHzV2—1119_Aug15 Page 14 of 16

Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 59.24 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 35.5 W/kg SAR(1 g) = 8.1 W/kg; SAR(10 g) = 2.25 W/ikg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 57.15 V/m; Power Drift = 0.02 dB Peak SAR (extrapolated) = 36.5 W/kg SAR(I g) =7.91 W/kg; SAR(10 g) = 2.19 W/kg Maximum value of SAR (measured) = 19.6 W/kg —6.00 ~12.00 —18.00 —24.00 —30.00 0 dB = 18.1 W/kg = 12.58 dBW/kg Certificate No: D5GHzV2—1119_Aug15 Page 15 of 16

Impedance Measurement Plot for Body TSL zo 11 fAug 2015 11i:14:37 [CH1I) sii 1 4J FS 11 51.588 a —7A816 a 4.23618 pF 5 200,.000 000 MHz £ is CH1 Markers De l 2: 51.984 & % 2.r031 0 Cor * s 5.30000 GHz 3: 54.264 a C —4 * ‘ ~1.20827 & 5.50000 GHz 4 56.379 a P —140.63 m 155 5.60000 GHz 31 97.9510 a —3056.2 2 fi: 5.80000 GHz H1d ; CH2 Si1i LOG __3dBAREF —20dR _ _ 11—22,.827 dB S 200.000 900 MHz ... ... _@ wtigrmes + ces 4 ,, + ——4f.... 4 — es cmrmcmmmmmuccke alke.. od i 4 % L 4 | CHZ2 Markers Com _ | | | | | 2:—30,.805 dB f«.. 4 + FX 4 + 4 4 4 5.30000 GHz _emak.... 1 | | w y .fl;:: 4:—27.383 dB —} C | I _ f—/ | | 5.50000 GHz L + nc k 4 . uoCCA+ ; 3 pnecnc e h «4 4—24.441 dB fi"-"B + 4 4 4 4 k. d 5.60000 GHz 16 [ 7 | i—.. + | x’ L———+ 4 4 | + | 4 | j —23.9052 4B 5.80000 GHz Hid l————+ + + + + + 4 | START 5aab.008ase MHz _ ~~STOP6B0b.oosbopMHz Certificate No: D5GHzV2—1119_Aug15 Page 16 of 16

Report Number: SAR.20180604 Appendix F – Phantom Calibration Data Sheets © 2018 RF Exposure Lab, LLC Page 125 of 127 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC.

Schmid & Partner Engineering AG e _2 Zeughausstrasse 43, 8004 Zurich, Switzerland Phone +41 44 245 9700, Fax +41 44 245 9779 info@speag.com, http. //www.speag.com Certificate of Conformity / First Article Inspection Item Oval Flat Phantom ELI 4.0 Type No QD OVA 001 B Series No 1003 and higher Manufacturer Untersee Composites Knebelstrasse 8 CH—8268 Mannenbach, Switzerland Tests Complete tests were made on the prototype units QD OVA 001 AA 1001, QD OVA 001 AB 1002, pre—series units QD OVA 001 BA 1003—1005 as weil as on the series units QD OVA 001 BB, 1006 ff. Test Requirement Details Units tested Material Compliant with the standard Bottom plate: all thickness requirements 2.0mm +/— 0.2mm Material Dielectric parameters for required < 6 GHz: Rel. permittivity = 4 Material parameters frequencies +/—1, Loss tangent < 0.05 sample Material The material has been tested to be DGBE based simulating Equivalent resistivity compatible with the liquids defined in liquids. phantoms, the standards if handled and cleaned Observe Technical Note for Material according to the instructions. material compatibility. sample Shape Thickness of botom material, Bottom elliptical 600 x 400 mm Prototypes, Internal dimensions, Depth 190 mm, Sample Sagging Shape is within tolerance for testing compatible with standards from filling height up to 155 mm, minimum frequency Eventual sagging is reduced or eliminated by support via DUT Standards [1] CENELEC EN 50361—2001, « Basic standard for the measurement of the Specific Absorption Rate related to human exposure to electromagnetic fields from mobile phones (300 MHz — 3 GHz) », July 2001 [2] IEEE 1528—2003, "Recommended Practice for Determining the Peak Spatial—Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques, December 2003 [3] IEC 62209 — 1, "Specific Absorption Rate (SAR) in the frequency range of 300 MHz to 3 GHz — Measurement Procedure, Part 1: Hand—held mobile wireless communication devices", February 2005 [4] IEC 62209 —— 2, Draft, "Human Exposure to Radio Frequency Fields from Handheld and Body— Mounted Wireless Communication Devices — Human models, Instrumentation and Procedures — Part 2: Procedure to determing the Specific Absorption Rate (SAR) in the head and body for 30 MHz to 6 GHz Handheld and Body—Mounted Devices used in close proximity to the Body.", February 2005 [8] OET Bulletin 65, Supplement C, "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields", Edition January 2001 Based on the tests above, we certify that this item is in compliance with the standards [1] to [5] if operated according to the specific requirements and considering the thickness. The dimensions are fully compliant with [4] from 30 MHz to 6 GHz. For the other standards, the minimum lower frequency limit is limited due to the dimensional requirements ([1]: 450 MHz, [2]: 300 MHz, [3]: 800 MHz, [5]:; 375 MHz) and possibly further by the dimensions of the DUT. § P 8 @ Schmid&&Partner Engineering AG Date 28.4.2008 Signature / Stamp Zeughaugétrasse 43,8004 Zurich, Switzectand Phone 441 44 245 9700, Fax +41,44,245 9779 info@gbeag.com; hitp//wwww.speag.com Doc No 881 —QD OVA 001 B— D Page 1 (1)

Report Number: SAR.20180604 Appendix G – Validation Summary Per FCC KDB 865664 D02 v01r02, SAR system validation status should be documented to confirm measurement accuracy. The SAR systems (including SAR probes, system components and software versions) used for this device were validated against its performance specifications prior to the SAR measurements. Reference dipoles were used with the required tissue equivalent media for system validation according to the procedures outlined in FCC KDB 865664 D01 v01r04 and IEEE 1528-2013. Since SAR probe calibrations are frequency dependent, each probe calibration point was validated at a frequency within the valid frequency range of the probe calibration point using the system that normally operates with the probe for routine SAR measurements and according to the required tissue equivalent media. A tabulated summary of the system validation status including the validation date(s), measurement frequencies, SAR probes and tissue dielectric parameters has been included. Table G-1 SAR System Validation Summary SAR CW Validation Modulation Valildation Freq. Probe Probe Probe Cal. Cond. Perm. System Date Sens- Probe Probe Modulation Duty (MHz) S/N Type Point (σ) (ɛr) PAR # itivity Linearity Isotropy Type Factor 2 2450 1/22/2015 3833 EX3DV4 2450 Body 1.97 52.53 Pass Pass Pass OFDM/TDD Pass Pass 2 5200 1/23/2015 3833 EX3DV4 5200 Body 5.32 48.94 Pass Pass Pass OFDM N/A Pass 2 5300 1/23/2015 3833 EX3DV4 5300 Body 5.45 48.74 Pass Pass Pass OFDM N/A Pass 2 5500 1/23/2015 3833 EX3DV4 5500 Body 5.68 48.29 Pass Pass Pass OFDM N/A Pass 2 5600 1/24/2015 3833 EX3DV4 5600 Body 5.79 48.33 Pass Pass Pass OFDM N/A Pass 2 5800 1/24/2015 3833 EX3DV4 5800 Body 6.03 48.14 Pass Pass Pass OFDM N/A Pass © 2018 RF Exposure Lab, LLC Page 127 of 127 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC.


Document Created: 2018-06-13 15:43:41
Document Modified: 2018-06-13 15:43:41
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC