RF Exposure SAR Report Calibration 3

FCC ID: PD98260D2

RF Exposure Info

Download: PDF
FCCID_4161773

KCTL Inc. Report No.: 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea KR19-SPF0001 TEL: 82-31-285-0894 FAX: 82-505-299-8311 Page (85) of (115) www.kctl.co.kr Appendix A.2 Dipole Calibration certificate D2450V2 This test report shall not be reproduced, except in full, without the written approval KCTL-TIA002-004/1

Calibration t Laboratory of G Schweizerischer Kalibrierdienst Schmid & Partner c Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland S swiss Calibration Service Aceredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM xy,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessmentof Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Condiitions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input power. * SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2450V2—895_Jul18 Page 2 of 8

> e errrrnmnm n ies 0_ KCTL Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY3 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 2 0.2) °C 87.8 26 % 1.85 mho/m x 6 % Head TSL temperature change during test <0.5 °C —— —— SAR result with Head TSL SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 250 mW input power 13.1 Wkg SAR for nominal Head TSL parameters normalized to 1W 51.3 W/kg x 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 6.10 Wig SAR for nominal Head TSL parameters normalized to 1W 24.1 Wikg £ 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 £0.2) °C 51.9 26 % 2.02 mho/m 2 6 % Body TSL temperature change during test <0.5 °C ~— SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 12.9 Wikg SAR for nominal Body TSL parameters normalized to 1W 50.6 Wikg x 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 6.03 Wkg SAR for nominal Body TSL parameters normalized to 1W 23.8 Wikg # 16.5 % (k=2) Certificate No: D2450V2—895_Jul18 Page 3 of 8 nonmes ryrpevecs aernan naga c rrmwiaze wwon d

KCTL Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 53.8 0 +1.8 jQ Return Loss —27.9 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 49.2 Q + 5.0 jQ Return Loss ~25.9 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.156 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessiveforce must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on June 19, 2012 Certificate No: D2450V2—895_Jul18 Page 4 of 8

— se oo es KCTL DASY5 Validation Report for Head TSL Date: 24.07.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN:895 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f= 2450 MHz; a= 1.85 S/m; s;=37.8; p = 1000 kg/m? Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/EC/ANSI C63.19—201 1) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(7.88, 7.88, 7.88) @ 2450 MHz: Calibrated: 30.12.2017 * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 26.10.2017 & Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 + DASY32 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 115.0 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 26.1 W/kg SAR(I g) = 13.1 W/kg; SAR(10 g) = 6.1 W/kg Maximum value of SAR (measured) = 21.4 W/kg dB 0 ~4.40 —8.80 13.20 ~17.60 ~22.00 0 dB = 21.4 W/kg = 13.30 dBW/kg Certificate No: D2450V2—895_Ju18 Page 5 of 8

Impeclance Measurement Plot for Head TSL 2450000 GHz 53.813 O 115.00 pH 17703 0 | , 2450000 GHz 40.493 mU | 923.925° +| ChiAvg= 20 Ch1: Start 225000 GHe Stop 2.65000 GHz | —21.852 dB oo 00 0o oo oo & Chi: Star 2.25000 GHe —— 265000 GHe Certificate No: D2450V2—895_Jul18 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 24.07.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN:895 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f= 2450 MHz; 0 = 2.02 S$/m; &; = 51.9; p = 1000 kg/m] Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: Probe: EX3DV4 — SN7349; ConvF(8.01, 8.01, 8.01) @ 2450 MHz:; Calibrated: 30.12.2017 Sensor—Surface: 1.4mm (Mechanical Surface Detection) Electronics: DAE4 Sn601; Calibrated: 26.10.2017 Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA: Serial: 1002 DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=Smm Reference Value = 108.0 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 25.1 W/kg SAR(I g) = 12.9 W/kg; SAR(10 g) =6.03 W/kg Maximum value of SAR (measured) = 20.9 W/kg 200 1s.00 —21.00 0 dB = 20.9 W/kg = 13.20 dBW/kg Certificate No: D2450V2—895_Jul18 Page 7 of 8

KCTL Inc. Report No.: 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea KR19-SPF0001 TEL: 82-31-285-0894 FAX: 82-505-299-8311 Page (92) of (115) www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval KCTL-TIA002-004/1

KCTL Inc. Report No.: 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea KR19-SPF0001 TEL: 82-31-285-0894 FAX: 82-505-299-8311 Page (93) of (115) www.kctl.co.kr D5GHzV2 This test report shall not be reproduced, except in full, without the written approval KCTL-TIA002-004/1

Calibration Laboratory of G Schweizerischer Kalibrierdienst Schmid & Partner _ Service suisse d‘étalonnage Engineering AG Servizio svizzero dtaratura Zeughausstrasse 49, 8004 Zurich, Switzerland S swiss Calibration Service Acoredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 c) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: d) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. & SAR measured: SAR measured at the stated antenna input power. & SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. «_ SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1184_May17 Page 2 of 16

KCTL Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY3 V52.10.0 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy =4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5200 MHz # 1 MHz 5300 MHz + 1 MHz Frequency 5500 MHz + 1 MHz 5600 MHz a 1 MHz 5800 MHz + 1 MHz Head TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.0 4.66 mho/m Measured Head TSL parameters (22.0 2 0.2) °C 84.8 26 % 4.55 mho/m + 6 % Head TSL temperature change during test <0.5°C —— ~—— SAR result with Head TSL at 5200 MHz SAR averaged over 1 cm° (1 g) of Head TSL Condition SAR measured 100 mW input power 8.03 Wikg SAR for nominal Head TSL parameters normalized to 1W 79.7 Wikg £ 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.28 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.6 Wikg 2 19.5 % (k=2) Head TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.76 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 34.7 26 % 4.64 mho/m + 6 % Head TSL temperature change during test <0.5 °C —— ~— SAR result with Head TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.31 Wikg SAR for nominal Head TSL parameters normalized to 1W 82.5 W / kg £ 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.39 Wikg SAR for nominal Head TSL parameters normalized to 1W 28.7 Wikg # 19.5 % (k=2) Certificate No: D5GHzV2—1134_May17 Page 3 of 16

—_— Clz lc 1. e ao nc mm mm ww mm a \ — mm KCTL mm Head TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.6 4.96 mho/m Measured Head TSL parameters (22.0 0.2) °C 84.4 26 % 4.84 mho/m + 6 % Head TSL temperature change during test <0.5 °C «o «e SAR result with Head TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.52 Wig SAR for nominal Head TSL parameters normalized to 1W 84.5 Wikg x 19.9 % (k=2) SAR averaged over 10 cm° (10 g) of Head TSL condition SAR measured 100 mW input power 2.43 Whg SAR for nominal Head TSL parameters normalized to 1W 24.1 Wikg £ 19.5 % (k=2) Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 0.2) °C 34.2 26 % 4.95 mho/m 2 6 % Head TSL temperature change during test <0.5 °C —— SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.51 Wikg SAR for nominal Head TSL parameters normalized to 1W 84.4 Wikg 2 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.42 Wig SAR for nominal Head TSL parameters normalized to 1W 23.9 Wikg x 19.5 % (k=2) Certificate No: D5GHzV2—1134_May17 Page 4 of 16 omm m cce ee se w en e e ko pen n n n es

mec in 9y vn nz KCTL Head TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 85.3 5.27 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 34.0 26 % 5.16 mho/m x 6 % Head TSL temperature change during test <0.5 °C «. «e= SAR result with Head TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.11 Wikg SAR for nominal Head TSL parameters normalized to 1W 80.4 W/kg x 19.9 % (k=2) SAR averaged over 10 cm? (10 g) of Head TSL condition SAR measured 100 mW input power 2.31 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.9 Wikg 2 19.5 % (k=2) Certificate No: D5GHzV2—1134_May17 Page 5 of 16

mecnan / — |KCTL Body TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 49.0 5.30 mho/m Measured Body TSL parameters (22.0 2 0.2) °C 47.6 26 % 5.44 mho/m + 6 % Body TSL temperature change during test <0.5 °C —— —— SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.34 Wig SAR for nominal Body TSL parameters normalized to 1W 73.0 Wikg £ 19.9 % (k=2) SAR averaged over 10 cm° (10 g) of Body TSL condition SAR measured 100 mW input power 2.06 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.5 Wikg x 19.5 % (k=2) Body TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.42 mho/m Measured Body TSL parameters (22.0 x 0.2) °C 47.4 26 % 5.57 mho/m x 6 % Body TSL temperature change during test <0.5 °C ~~— SAR result with Body TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.80 Wikg SAR for nominal Body TSL parameters normalized to 1W 77.6 Wikg 2 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.20 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.9 Wikg 2 19.5 %(k=2) Certificate No: D5GHzV2—1134_May17 Page 6 of 16

mecn in 9y von nz KCTL Body TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.6 5.65 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 47.0 26 % 5.84 mho/m x 6 % Body TSL temperature change during test <0.5 °C —— SAR result with Body TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 8.12 Wig SAR for nominal Body TSL parameters normalized to 1W 80.8 W/kg x 19.9 % (k=2) SAR averaged over 10 cm° (10 g) of Body TSL condition SAR measured 100 mW input power 2.26 Wkg SAR for nominal Body TSL parameters normalized to 1W 22.4 Wikg £ 19.5 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 46.9 £6 % 5.98 mho/m 2 6 % Body TSL temperature change during test <0.5 °C ~~ SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 8.05 Wkg SAR for nominal Body TSL parameters normalized to 1W 80.1 Wikg # 19.9 % (k=2) SAR averaged over 10 cm(10 g) of Body TSL condition SAR measured 100 mW input power 2.27 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.5 Wikg £ 19.5 % (k=2) Certificate No: D5GHzV2—1134_May17 Page 7 of 16

mecn in n y von nz KCTL Body TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mho/m Measured Body TSL parameters (22.0 £0.2) °C 46.5 26 % 6.26 mho/m x 6 % Body TSL temperature change during test <0.5 °C —— SAR result with Body TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.76 Wikg SAR for nominal Body TSL parameters normalized to 1W 77.2 Wikg # 19.9 % (k=2) SAR averaged over 10 cm° (10 g) of Body TSL condition SAR measured 100 mW input power 2.16 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.4 Wikg 2 19.5 % (k=2) Certificate No: D5GHzV2—1134_May17 Page 8 of 16

KCTL Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 49.2 0 — 9.6 jQ Return Loss —20.3 dB Antenna Parameters with Head TSL at 5300 MHz Impedance, transformed to feed point 50.0 2 —7.2 jQ Return Loss —22.9 dB Antenna Parameters with Head TSL at 5500 MHz Impedance, transformed to feed point 52.0 Q — 4.5 jQ Return Loss —26.3 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 53.9 0 —3.2j0 Return Loss — 26.3 dB Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point 55.6 0 — 4.3 jQ Return Loss —23.5 dB Antenna Parameters with Body TSL at 5200 MHz Impedance, transformed to feed point 49.1 0 —8.3j0 Return Loss —21.5 dB Antenna Parameters with Body TSL at 5300 MHz Impedance, transformed to feed point 49.8 0 — 5.0 jQ Return Loss —26.1 dB Antenna Parameters with Body TSL at 5500 MHz Impedance, transformed to feed point 51.6 0 —1.6 jQ Return Loss —33.0 dB Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 55.4 0 — 0.8 jQ Return Loss —25.7 dB Certificate No: D5GHzV2—1134_May17 Page 9 of 16

Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point 56.5 0 — 3.5 jQ Return Loss —23.2 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.204 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole armsin order to improve matching when loaded according to the position as explained in the "Measurement Conditions® paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessiveforce must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on May 07, 2012 Certificate No: D5GHzV2—1134_May17 Page 10 of 16

moy pres ——— |KCTL DASY5 Validation Report for Head TSL Date: 24.05.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole D5GHzV2; Type: DSGHzV2; Serial: D5GHzV2 — SN:1134 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: {= 5200 MHz; 0 = 4.55 S/m; & = 34.8; p = 1000 kg/m‘ , Medium parameters used: f = 5300 MHz; 0 = 4.64 S/m; & = 34.7; p = 1000 kg/m© , Medium parameters used: £= 5500 MHz; 0 = 4.84 S/m; & = 34.4; p = 1000 kg/m3 , Medium parameters used: £= 5600 MHz; a = 4.95 S/m; & = 34.2; p = 1000 kg/m? , Medium parameters used: f= 5800 MHz; 0 = 5.16 $/m; &= 34; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: & Probe: EX3DV4 — SN3503; ConvF(5.76, 5.76, 5.76); Calibrated: 31.12.2016, ConvF(5.35, 5.35, 5.35); Calibrated: 31.12.2016, ConvF(5.2, 5.2,5.2); Calibrated: 31.12.2016, ConyF(5.09, 5.09, 5.09); Calibrated: 31.12.2016, ConvF(5.01, 5.01, 5.01); Calibrated: 31.12.2016; + Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 + DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, f=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 69.33 V/m; Power Drift = —0.06 dB Peak SAR (extrapolated) = 29.4 W/kg SAR(I g) = 8.03 W/kg; SAR(10 g) = 2.28 W/kg Maximum value of SAR (measured) = 18.6 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value =71.66 V/m; Power Drift =—0.02 dB Peak SAR (extrapolated) = 29.6 W/kg SAR(I g) = 8.31 W/kg; SAR(10 g) =2.39 W/kg Maximum value of SAR (measured) = 19.3 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1 4mm Reference Value = 70.01 V/m; Power Drift =—0.08 dB Peak SAR (extrapolated) = 33.1 W/kg SAR(I g) = 8.52 W/kg; SAR(10 g) = 2.43 W/kg Maximum value of SAR (measured) = 20.1 W/kg Certificate No: D5GHzV2—1134_May17 Page 11 of 16

mO e KCTL Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, f=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 70.02 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) = 33.2 W/kg SAR(I g) = 8.51 W/kg; SAR(10 g) = 242 W/kg Maximum value of SAR (measured) = 20.3 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Mcasurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 68.71 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 32.7 W/kg SAR(I g) = 8.11 W/kg:; SAR(1O g) =2.31 W/kg Maximum value of SAR (measured) = 19.8 W/kg dB 0 —5.00 —10.00 —15.00 ~20.00 —25.00 0 dB = 18.6 W/kg = 12.70 dBW/g Certificate No: D5GHzV2—1184_May17 Page 12 of 16

m ons e KCTL Impedance Measurement Plot for Head TSL 24 May reir igrssiss CH® sn 4 uo rs i49213 0 —960940 34854 pF 5 200.000 000 MHz e s¥ > CHA Markers te1 s 2: 50,025 a —74895 a tor { 5.30000 GHz I | — a 52007 a —— 7 ~4.918e a s.se000 oiz 4 4 4 53.922 a 31555 a 2\59 «L > 5.60000 GHz 95.548 a — # ~4.2935 A Hia s.eada0 GHz cH2 sir _Los _5 ds/rer —20 ge e 11=20.292 ds _5 200.000 000 Miz, ko ul ineh sc h d ho ied ce | L. | | | CH2 Mankens h( ———4~ "I T=~+——1~ 22.980 do Sst iI m + deo0 ciz 26.273 aB s.se000 oz :—28.259 d8 Avg 5.60000 olz i6 (__L [200 _2 _OOUb IP .c 1—23.400 ds | | 1 | | s.ea000 GHz ma |— | |—— L LELLL _ EEL_L____] | I ~staRt5000.000ooo mz Certificate No: D5GHzV2—1134_May17 Page 13 of 16

moy pres ——— |KCTL DASY5 Validation Report for Body TSL Date: 26.05.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole D5GHzV2; Type: DSGHzV2; Serial: DSGHzV2 — SN:1205 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: £= 5200 MHz; 0 = 5.44 S/m; & = 47.6; p = 1000 kg/m‘ , Medium parameters used: f = 5300 MHz; 0 = 5.57 S/m; & = 47.4; p = 1000 kg/m, Medium parameters used: £= 5500 MHz; 0 = 5.84 $/m; & = 47; p = 1000 kg/m‘ , Medium parameters used: £ = 5600 MHz; 0 = 5.98 S/m; &; = 46.9; p = 1000 kg/m? , Medium parameters used: f = 5800 MHz; 0 = 6.26 $/m; s = 46.5; p = 1000 kg/m> Phantom section: Flat Section Measurement Standard: DASYS (IEEE/EC/ANST C63.19—2011) DASY52 Configuration: «_ Probe: EX3DV4 — SN3503; ConvF(5.29, 5.29, 5.29); Calibrated: 31.12.2016, ConvF(5.04, 5.04, 5.04); Calibrated: 31.12.2016, ConvF(4.62, 4.62, 4.62); Calibrated: 31.12.2016, ConvF(4.57, 4.57, 4.57); Calibrated: 31.12.2016, ConvF(4.48, 4.48, 4.48); Calibrated: 31.12.2016; «_ Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 + DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, f=5200MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 64.07 V/m; Power Drift = —0.01 dB Peak SAR (extrapolated) = 27.8 W/kg SAR(I g) =7.34 W/kg; SAR(10 g) = 2.06 W/kg Maximum value of SAR (measured) = 17.4 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 65.52 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 30.1 W/kg SAR(I g) =7.8 W/kg; SAR(10 g) =2.2 W/kg Maximum value of SAR (measured) = 18.5 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 66.06 V/m; Power Drift =—0.03 dB Peak SAR (extrapolated) = 33.1 W/kg SAR(I g) = 8.12 W/kg; SAR(10 g) = 2.26 W/kg Maximum value of SAR (measured) = 19.8 W/kg Certificate No: DBGHzV2—1134_May17 Page 14 of 16

eO es KCTL Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 65.36 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 33.3 W/kg SAR(I g) = 8.05 W/kg; SAR(10 g) = 2.27 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 63.60 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 34.0 W/kg SAR(I g) =7.76 W/kg; SAR(10 g) = 2.16 W/kg Maximum value of SAR (measured) = 19.3 W/kg dB 0 5.00 —10.00 —15.00 —20.00 ~25.00 0 dB = 17.4 W/kg = 12.41 dBW/kg Certificate No: D5GHzV2—1134_May17 Page 15 of 16

KCTL Inc. Report No.: 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea KR19-SPF0001 TEL: 82-31-285-0894 FAX: 82-505-299-8311 Page (108) of (115) www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval KCTL-TIA002-004/1


Document Created: 2019-03-25 00:09:17
Document Modified: 2019-03-25 00:09:17
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC