Test Report DFS

FCC ID: PD9622ANHU

Test Report

Download: PDF
FCCID_1173388

TEST REPORT Covering the DYNAMIC FREQUENCY SELECTION (DFS) REQUIREMENTS OF FCC Part 15 Subpart E (UNII) & RSS210 Issue 7 Intel Corporation Intel® Centrino® Advanced-N 6200 Model: 622ANHMW FCC ID: PD9622ANH IC UPN: 1000M-622ANH COMPANY: Intel Corporation 2111 N.E. 25th Avenue JF3-3-G14 Hillsborough, OR, 97124-5961 TEST SITE: Elliott Laboratories 684 W. Maude Ave Sunnyvale, CA 94085 REPORT DATE: August 27, 2009 FINAL TEST DATE: August 27, 2009 TEST ENGINEER: Wayne Fisher AUTHORIZED SIGNATORY: ______________________________ David W. Bare Chief Engineer Testing Cert #2016-01 Elliott Laboratories is accredited by the A2LA, certificate number 2016-01, to perform the test(s) listed in this report. This report shall not be reproduced, except in its entirety, without the written approval of Elliott Laboratories File: R76613 Page 1 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 REVISION HISTORY Rev # Date Comments Modified By - September 1, 2009 First Release - File: R76613 Page 2 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 TABLE OF CONTENTS COVER PAGE.............................................................................................................................................................1 REVISION HISTORY................................................................................................................................................2 TABLE OF CONTENTS ............................................................................................................................................3 LIST OF TABLES.......................................................................................................................................................3 LIST OF FIGURES.....................................................................................................................................................4 SCOPE..........................................................................................................................................................................5 OBJECTIVE ................................................................................................................................................................5 STATEMENT OF COMPLIANCE...........................................................................................................................5 DEVIATIONS FROM THE STANDARD ................................................................................................................5 EQUIPMENT UNDER TEST (EUT) DETAILS......................................................................................................6 GENERAL................................................................................................................................................................6 ENCLOSURE...........................................................................................................................................................6 MODIFICATIONS...................................................................................................................................................6 SUPPORT EQUIPMENT.........................................................................................................................................7 EUT INTERFACE PORTS ......................................................................................................................................7 EUT OPERATION ...................................................................................................................................................7 RADAR WAVEFORMS.............................................................................................................................................8 TEST RESULTS..........................................................................................................................................................9 TEST RESULTS SUMMARY – FCC PART 15, CLIENT DEVICE .......................................................................9 MEASUREMENT UNCERTAINTIES....................................................................................................................9 DFS TEST METHODS .............................................................................................................................................10 RADIATED TEST METHOD ...............................................................................................................................10 DFS MEASUREMENT INSTRUMENTATION....................................................................................................12 RADAR GENERATION SYSTEM .......................................................................................................................12 CHANNEL MONITORING SYSTEM ..................................................................................................................13 DFS MEASUREMENT METHODS .......................................................................................................................14 DFS – CHANNEL CLOSING TRANSMISSION TIME AND CHANNEL MOVE TIME ..................................14 DFS – CHANNEL NON-OCCUPANCY AND VERIFICATION OF PASSIVE SCANNING............................14 DFS CHANNEL AVAILABILITY CHECK TIME...............................................................................................15 TRANSMIT POWER CONTROL (TPC) ..............................................................................................................15 SAMPLE CALCULATIONS ...................................................................................................................................16 DETECTION PROBABILITY / SUCCESS RATE ...............................................................................................16 THRESHOLD LEVEL ...........................................................................................................................................16 APPENDIX A TEST EQUIPMENT CALIBRATION DATA ..............................................................................17 APPENDIX B TEST DATA TABLES AND PLOTS FOR CHANNEL CLOSING ...........................................18 FCC PART 15 SUBPART E CHANNEL CLOSING MEASUREMENTS .................................................................18 APPENDIX C ANTENNA SPECIFICATION SHEET.........................................................................................25 APPENDIX D TEST CONFIGURATION PHOTOGRAPHS..............................................................................29 LIST OF TABLES Table 1 FCC Short Pulse Radar Test Waveforms......................................................................................... 8 Table 2 FCC Long Pulse Radar Test Waveforms......................................................................................... 8 Table 3 FCC Frequency Hopping Radar Test Waveforms ........................................................................... 8 Table 4 FCC Part 15 Subpart E Client Device Test Result Summary .......................................................... 9 Table 5 FCC Part 15 Subpart E Channel Closing Test Results .................................................................. 18 File: R76613 Page 3 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 LIST OF FIGURES Figure 1 Test Configuration for radiated Measurement Method ................................................................ 10 Figure 2 Channel Closing Time and Channel Move Time – 40 second plot .............................................. 19 Figure 3 Close-Up of Transmissions Occurring More Than 200ms After The End of Radar .................... 20 Figure 4 Channel Closing Time and Channel Move Time – 40 second plot .............................................. 21 Figure 5 Close-Up of Transmissions Occurring More Than 200ms After The End of Radar .................... 22 Figure 6 Radar Channel Non-Occupancy Plot, n20 mode.......................................................................... 23 Figure 7 Radar Channel Non-Occupancy Plot , n40 mode......................................................................... 24 File: R76613 Page 4 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 SCOPE The Federal Communications Commission publishes standards regarding Radio spectrum matters for radio-communications devices. Tests have been performed on the Intel Corporation Intel® Centrino® Advanced-N 6200 model 622ANHMW in accordance with one of these standards. Test data has been taken pursuant to the relevant DFS requirements of the following standard(s). In the cases of ETSI (EN) standards, testing was limited to those aspects covering essential requirements under article 3.2 of the R&TTE Directive pertaining to DFS: • FCC Part 15 Subpart E Unlicensed National Information Infrastructure (U-NII) Devices Tests were performed in accordance with these standards together with the current published versions of the basic standards referenced therein as outlined in Elliott Laboratories test procedures. The test results recorded herein are based on a single type test of the Intel Corporation Intel® Centrino® Advanced-N 6200 model 622ANHMW and therefore apply only to the tested sample. The sample was selected and prepared by Steve Hackett of Intel Corporation. OBJECTIVE The objective of the manufacturer is to comply with the standards identified in the previous section. In order to demonstrate compliance, the manufacturer or a contracted laboratory makes measurements and takes the necessary steps to ensure that the equipment complies with the appropriate technical standards. Compliance with some DFS features is covered through a manufacturer statement or through observation of the device. STATEMENT OF COMPLIANCE The tested sample of Intel Corporation Intel® Centrino® Advanced-N 6200 model 622ANHMW complied with the DFS requirements of: FCC Part 15.407(h)(2) Maintenance of compliance is the responsibility of the manufacturer. Any modifications to the product should be assessed to determine their potential impact on the compliance status of the device with respect to the standards detailed in this test report. DEVIATIONS FROM THE STANDARD No deviations were made from the test methods and requirements covered by the scope of this report. File: R76613 Page 5 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 EQUIPMENT UNDER TEST (EUT) DETAILS GENERAL The Intel Corporation Intel® Centrino® Advanced-N 6200 model 622ANHMW is a half- mini 2x2 agn wifi radio for use in computers. The sample was received on August 26, 2009 and tested on August 27, 2009. The EUT consisted of the following component(s): Manufacturer Model Description Mac Number Intel 622ANHMW 2x2 agn radio 0015005A7040 The manufacturer declared values for the EUT operational characteristics that affect DFS are as follows: Operating Modes (5250 – 5350 MHz, 5470 – 5725 MHz) Master Device Client Device (no In Service Monitoring, no Ad-Hoc mode) Client Device with In-Service Monitoring Antenna Gains / EIRP (5250 – 5350 MHz, 5470 – 5725 MHz) 5250 – 5350 MHz 5470 – 5725 MHz Lowest Antenna Gain (dBi) 2.57 4.43 Highest Antenna Gain (dBi) 3.73 4.76 Power can exceed 200mW eirp Channel Protocol IP Based Frame Based OTHER _____________________ ENCLOSURE The EUT has no enclosure. It is designed to be installed within the enclosure of a host computer. MODIFICATIONS The EUT did not require modifications during testing in order to comply with the requirements of the standard(s) referenced in this test report. File: R76613 Page 6 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 SUPPORT EQUIPMENT The following equipment was used as local support equipment for testing: Manufacturer Model Description Serial Number FCC ID Toshiba PSA G8U- Laptop computer 49290792Q DoC 0400 1W Cisco Air 1252 Wireless Access Point FTX1209906V LDK 102 061 AG-AK9 The italicized device was the master device. EUT INTERFACE PORTS The I/O cabling configuration during testing was as follows: Cable(s) Port Connected To Description Shielded or Unshielded Length (m) None - - - - EUT OPERATION The EUT was operating with the following software. The software is secured by encryption to prevent the user from disabling the DFS function. Client Device: 13.0.0.91 During the channel moving tests the system was configured with a streaming video file from the master device (sourced by the PC connected to the master device via an Ethernet interface) to the client device. The streamed file was the “FCC” test file and the client device was using Windows Media Player Classic as required by FCC Part 15 Subpart E File: R76613 Page 7 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 RADAR WAVEFORMS Table 1 FCC Short Pulse Radar Test Waveforms Minimum Minimum Pulse Width PRI Pulses / Radar Type Detection Number of (µsec) (µsec) burst Percentage Trials 1 1 1428 18 60% 30 2 1-5 150-230 23-29 60% 30 3 6-10 200-500 16-18 60% 30 4 11-20 200-500 12-16 60% 30 Aggregate (Radar Types 1-4) 80% 120 Table 2 FCC Long Pulse Radar Test Waveforms Pulse Chirp Minimum Minimum Radar PRI Pulses / Number Width Width Detection Number of Type (µsec) burst of Bursts (µsec) (MHz) Percentage Trials 5 50-100 5-20 1000- 1-3 8-20 80% 30 2000 Table 3 FCC Frequency Hopping Radar Test Waveforms Hopping Pulse Hopping Minimum Minimum Radar PRI Pulses / Sequence Width Rate Detection Number of Type (µsec) hop Length (µsec) (kHz) Percentage Trials (msec) 6 1 333 9 0.333 300 70% 30 File: R76613 Page 8 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 TEST RESULTS TEST RESULTS SUMMARY – FCC Part 15, CLIENT DEVICE Table 4 FCC Part 15 Subpart E Client Device Test Result Summary Radar Radar Measured Description Requirement Test Data Status Type Frequency Value Channel closing transmission time Type 1 5260MHz 1ms 60ms Appendix B Complied (n40 mode) Channel move Type 1 5260MHz 504ms 10s Appendix B Complied time (n40 mode) Channel closing transmission time Type 1 5280MHz 1.18ms 60ms Appendix B Complied (n20 mode) Channel move Type 1 5280MHz 2.1s 10s Appendix B Complied time (n20 mode) Non-occupancy period – Type 1 5260 MHz > 30 minutes > 30 minutes Appendix B Complied associated (n40 mode) Non-occupancy period – Type 1 5280MHz > 30 minutes > 30 minutes Appendix B Complied associated (n20 mode) Notes: 1) Tests were performed using the radiated test method. 2) Channel availability check, detection threshold and non-occupancy period are not applicable to client devices. MEASUREMENT UNCERTAINTIES ISO/IEC 17025 requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level, with a coverage factor (k=2) and were calculated in accordance with UKAS document LAB 34. Measurement Measurement Unit Expanded Uncertainty Timing Timing resolution +/- (Channel move time, aggregate ms 0.24% transmission time) Timing seconds 5 seconds (non occupancy period) DFS Threshold (radiated) dBm 1.6 DFS Threshold (conducted) dBm 1.2 File: R76613 Page 9 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 DFS TEST METHODS RADIATED TEST METHOD The combination of master and slave devices is located in an anechoic chamber. The simulated radar waveform is transmitted from a directional horn antenna (typically an EMCO 3115) toward the unit performing the radar detection (radar detection device, RDD). Every effort is made to ensure that the main beam of the EUT’s antenna is aligned with the radar-generating antenna. Anechoic Chamber Master Device Radar ~3m Antenna Monitoring Antenna Traffic Monitoring Radar Generation System System Figure 1 Test Configuration for radiated Measurement Method File: R76613 Page 10 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 The signal level of the simulated waveform is set to a reference level equal to the threshold level (plus 1dB if testing against FCC requirements). Lower levels may also be applied on request of the manufacturer. The level reported is the level at the RDD antenna and so it is not corrected for the RDD’s antenna gain. The RDD is configured with the lowest gain antenna assembly intended for use with the device. The signal level is verified by measuring the CW signal level from the radar generation system using a reference antenna of gain G (dBi). The radar signal level is calculated from the measured level, R (dBm), and any cable loss, L (dB), between the reference antenna and the measuring instrument: Applied level (dBm) = R – GREF + L If both master and client devices have radar detection capability then the device not under test is positioned with absorbing material between its antenna and the radar generating antenna, and the radar level at the non RDD is verified to be at least 20dB below the threshold level to ensure that any responses are due to the RDD detecting radar. The antenna connected to the channel monitoring subsystem is positioned to allow both master and client transmissions to be observed, with the level of the EUT’s transmissions between 6 and 10dB higher than those from the other device. File: R76613 Page 11 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 DFS MEASUREMENT INSTRUMENTATION RADAR GENERATION SYSTEM An Agilent PSG is used as the radar-generating source. The integral arbitrary waveform generators are programmed using Agilent’s “Pulse Building” software and Elliott custom software to produce the required waveforms, with the capability to produce both un- modulated and modulated (FM Chirp) pulses. Where there are multiple values for a specific radar parameter then the software selects a value at random and, for FCC tests, the software verifies that the resulting waveform is truly unique. With the exception of the hopping waveforms required by the FCC’s rules (see below), the radar generator is set to a single frequency within the radar detection bandwidth of the EUT. The frequency is varied from trial to trial by stepping in 5MHz steps. Frequency hopping radar waveforms are simulated using a time domain model. A randomly hopping sequence algorithm (which uses each channel in the hopping radar’s range once in a hopping sequence) generates a hop sequence. A segment of the first 100 elements of the hop sequence are then examined to determine if it contains one or more frequencies within the radar detection bandwidth of the EUT. If it does not then the first element of the segment is discarded and the next frequency in the sequence is added. The process repeats until a valid segment is produced. The radar system is then programmed to produce bursts at time slots coincident with the frequencies within the segment that fall in the detection bandwidth. The frequency of the generator is stepped in 1 MHz increments across the EUT’s detection range. The radar signal level is verified during testing using a CW signal with the AGC function switched on. Correction factors to account for the fact that pulses are generated with the AGC functions switched off are measured annually and an offset is used to account for this in the software. The generator output is connected to the coupling port of the conducted set-up or to the radar-generating antenna. File: R76613 Page 12 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 CHANNEL MONITORING SYSTEM Channel monitoring is achieved using a spectrum analyzer and digital storage oscilloscope. The analyzer is configured in a zero-span mode, center frequency set to the radar waveform’s frequency or the center frequency of the EUT’s operating channel. The IF output of the analyzer is connected to one input of the oscilloscope. A signal generator output is set to send either the modulating signal directly or a pulse gate with an output pulse co-incident with each radar pulse. This output is connected to a second input on the oscilloscope and the oscilloscope displays both the channel traffic (via the if input) and the radar pulses on its display. For in service monitoring tests the analyzer sweep time is set to > 20 seconds and the oscilloscope is configured with a data record length of 10 seconds for the short duration and frequency hopping waveforms, 20 seconds for the long duration waveforms. Both instruments are set for a single acquisition sequence. The analyzer is triggered 500ms before the start of the waveform and the oscilloscope is triggered directly by the modulating pulse train. Timing measurements for aggregate channel transmission time and channel move time are made from the oscilloscope data, with the end of the waveform clearly identified by the pulse train on one trace. The analyzer trace data is used to confirm that the last transmission occurred within the 10-second record of the oscilloscope. If necessary the record length of the oscilloscope is expanded to capture the last transmission on the channel prior to the channel move. Channel availability check time timing plots are made using the analyzer. The analyzer is triggered at start of the EUT’s channel availability check and used to verify that the EUT does not transmit when radar is applied during the check time. The analyzer detector and oscilloscope sampling mode is set to peak detect for all plots. File: R76613 Page 13 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 DFS MEASUREMENT METHODS DFS – CHANNEL CLOSING TRANSMISSION TIME AND CHANNEL MOVE TIME Channel clearing and closing times are measured by applying a burst of radar with the device configured to change channel and by observing the channel for transmissions. The time between the end of the applied radar waveform and the final transmission on the channel is the channel move time. The aggregate transmission closing time is measured in one of two ways: FCC – the total time of all individual transmissions from the EUT that are observed starting 200ms at the end of the last radar pulse in the waveform. This value is required to be less than 60ms. ETSI1 – the total time of all individual transmissions from the EUT that are observed from the end of the last radar pulse in the waveform. This value is required to be less than 260ms. DFS – CHANNEL NON-OCCUPANCY AND VERIFICATION OF PASSIVE SCANNING The channel that was in use prior to radar detection by the master is additionally monitored for 30 minutes to ensure no transmissions on the vacated channel over the required non-occupancy period. This is achieved by tuning the spectrum analyzer to the vacated channel in zero-span mode and connecting the IF output to an oscilloscope. The oscilloscope is triggered by the radar pulse and set to provide a single sweep (in peak detect mode) that lasts for at least 30 minutes after the end of the channel move time. For devices with a client-mode that are being evaluated against FCC rules the manufacturer must supply an attestation letter stating that the client device does not employ any active scanning techniques (i.e. does not transmit in the DFS bands without authorization from a Master device). 1 This measurement method is used for MIC Table No. 45. File: R76613 Page 14 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 DFS CHANNEL AVAILABILITY CHECK TIME It is preferred that the EUT report when it starts the radar channel availability check. If the EUT does not report the start of the check time, then the time to start transmitting on a channel after switching the device on is measured to approximate the time from power- on to the end of the channel availability check. The start of the channel availability check is assumed to be 60 seconds prior to the first transmission on the channel. To evaluate the channel availability check, a single burst of one radar type is applied within the first 2 seconds of the start of the channel availability check and it is verified that the device does not use the channel by continuing to monitor the channel for a period of at least 60 seconds. The test is repeated by applying a burst of radar in the last 2 seconds (i.e. between 58 and 60 seconds after the start of CAC when evaluating a 60- second CAC) of the channel availability check. TRANSMIT POWER CONTROL (TPC) Compliance with the transmit power control requirements for devices is demonstrated through measurements showing multiple power levels and manufacturer statements explaining how the power control is implemented. File: R76613 Page 15 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 SAMPLE CALCULATIONS DETECTION PROBABILITY / SUCCESS RATE The detection probability, or success rate, for any one radar waveform equals the number of successful trials divided by the total number of trials for that waveform. THRESHOLD LEVEL The threshold level is the level of the simulated radar waveform at the EUT’s antenna. If the test is performed in a conducted fashion then the level at the rf input equals the level at the antenna plus the gain of the antenna assembly, in dBi. The gain of the antenna assembly equals the gain of the antenna minus the loss of the cabling between the rf input and the antenna. The lowest gain value for all antenna assemblies intended for use with the device is used when making this calculation. If the test is performed using the radiated method then the threshold level is the level at the antenna. File: R76613 Page 16 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 Appendix A Test Equipment Calibration Data Manufacturer Description Model # Asset # Cal Due EMC Spectrum Analyzer, 9 KHz-26.5 Hewlett Packard 8593EM 1141 29-Dec-09 GHz EMCO Antenna, Horn, 1-18 GHz 3115 1561 10-Jun-10 EMCO Antenna, Horn, 1-18 GHz 3117 1662 11-Apr-10 PSG Vector Signal Generator (250kHz Agilent E8267C 1877 15-Feb-10 - 20GHz) Tektronix 500MHz, 2CH, 5GS/s Scope TDS5052B 2118 N/A File: R76613 Page 17 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 Appendix B Test Data Tables and Plots for Channel Closing FCC PART 15 SUBPART E Channel Closing Measurements Table 5 FCC Part 15 Subpart E Channel Closing Test Results Channel Closing Channel Move Waveform Type Transmission Time 1 Time Result Measured Limit Measured Limit Radar Type 1 5520MHz 1 ms 60 ms 504 ms 10 s Complied n40 mode Radar Type 1 5280MHz 1.18 ms 60 ms 2.1 s 10 s Complied n20 mode After the final channel closing test the channel was monitored for a further 30 minutes. No transmissions occurred on the channel. 1 Channel closing time for FCC measurements is the aggregate transmission time starting from 200ms after the end of the radar signal to the completion of the channel move. File: R76613 Page 18 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 Figure 2 Channel Closing Time and Channel Move Time – 40 second plot File: R76613 Page 19 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 Figure 3 Close-Up of Transmissions Occurring More Than 200ms After The End of Radar File: R76613 Page 20 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 Figure 4 Channel Closing Time and Channel Move Time – 40 second plot File: R76613 Page 21 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 Figure 5 Close-Up of Transmissions Occurring More Than 200ms After The End of Radar File: R76613 Page 22 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 Figure 6 Radar Channel Non-Occupancy Plot, n20 mode The non-occupancy plot was made over a 30-minute time period following the channel move time with the analyzer IF output connected to the scope and tuned to the vacated channel. No transmissions were observed after the channel move had been completed. After the channel move the client re-associated with the master device on the new channel. After the channel move the client device stopped transmitting on the original channel. File: R76613 Page 23 of 29

Elliott Laboratories -- EMC Department Test Report Report Date: August 27, 2009 Figure 7 Radar Channel Non-Occupancy Plot , n40 mode The non-occupancy plot was made over a 30-minute time period following the channel move time with the analyzer IF output connected to the scope and tuned to the vacated channel. No transmissions were observed after the channel move had been completed. After the channel move the client re-associated with the master device on the new channel. After the channel move the client device stopped transmitting on the original channel. File: R76613 Page 24 of 29

54 (GHz) Band 5is 535 535 545 575 5g5 MAX Gain 164 257 3.73 47 443 497 caBn Efficiency (00) 61.74 g0.1 78.92 85.58 7831 69.99 Likzkiamki4f4 mRA d ” Tl Y -;5 = Shanghal Universe Communication Electronics Co. Ltd WHVERAE uns repmnmnns d1 36# ow c 20LI0E 4+ c 021—645t 5 Loaon. RF Chamber Dats: 2007340 Tone: 110700 Tenoerslan { ) 2200 pumidny 0) Gsan Approiad ay Total view o Freqeney (Viis) sxmam TR cBm Posk ERP (Bm) 20 257 Effeincy (%) Mex Poses (B) in 257 NHPR® t 45 (iBed Nin. Power(iBn) 2n asae NHPRP u30 (dBed Ara Pover (3Bt a2 asr Dieetiny sn hx / Min. Rato i) are irai Gain uen Max / Aug Rato i) 257 se ArerageGain(48) Nin. /Arg Ratio (E) 22 aasr 5.25GHz

J ikese io s m t —f s TRA S ” JJ WeR5e ShopghaiUniverse Communication Electronics Co. Ltd HEVEROE w aepmimemen o54644 ww oiice w: ol—ces s Lecaton. RE Chamber ous. morsse Inc: tz Tenssniert 3. zom rurimy c esn Appondoy Toatview Frepnsy tity seam necen beaie com aee an Eifvaney 0) Ns Pone(CBn) mese 5 wePho ue as ate) t Pover td an aaas mmone u 2 utm ho. 2oror cem as ae Oreainy an t hi. raio 5) an ie can um tee (m05 Rais 5 an sis Anoce Out Ni/A Rai C as men 535GHz

_c.38.—50 B S t 8 4A ThA S JJ W 2@5 g.— ShonghaiUniverse Communication Blectronics o Ltd HBTTEMADE uiss rompmenmmeem ds 4 6e esw 201108# : 21—Gtatant s Lecaion: RE Chamber ou. ause Ts nare Tensouss( ) zen umc . osa0 Armeirs Toview Fmserey Wttd seam ec Posere com as an Eneunsy 09 t Sovecom) sns a7n mnppo w as uted Nn Pove n is on wePro u2 td AuPorer(Bm) as aw Oresiny usn t in cato ue) sa Be can um trom Raio ud) «n fa Acoge Gain ut Nn (Au Rare C am aen 545GHz

_850 B s m t 4# ThA a] JJ We@5 & Shonghai Universe Communication Blectronics Co. Ltd HBTYERAOE ons onpmenmmeem ast 3 6 e sn c o0li0h wc otl—Goatast s Secato: RE Chamber bue auam Tre arman Tepsomer( ): zen ce m csan Appondoy Tout w Fomeney Wt smam ne com raame com ase «a Eneunsy 09 ts Por com) ma i5 mpne se as utm Mn Pover uted ase moce wrme um utm A,Porer (Bm) ais aa Dresiny usn t he. tu) zis 1us can um t Je ruis 5 i5 h Acoce Cl um Ni (An Raio@ s as 575GHz



Document Created: 2009-09-01 14:48:07
Document Modified: 2009-09-01 14:48:07
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC