Mod Req Letter

FCC ID: PBR-SZMDLBR1

Cover Letter(s)

Download: PDF
FCCID_1825330

Date: 10/03/2012 The Kroger Co. 11450 Grooms Rd Blue Ash, OH 45242 Applicant/Grantee DBion Perkins R&D Manager The Kroger Co., 11450 Grooms Rd. Blue Ash, OH 45242 United States FCC 1D: PBR—SZMDRLBR1 Section 15.212 Modular Transmitters Request for Single Modular Request for Limited Single Approval Modular approval 51. No Requirements EUT Conditions Comply {(Y/N) The radio slements of the modular transmitter must have their own The Module has RF shield 01 Shielding. The physical crystal and mounted on it Refer Appendix ¥ tuning capacitors may be located 2_EUT External Photos external to the shielded radio elements . All inputs are processed as data bufferedmodulatiordetainputeisuch bY the on—chip microcontrolier inputs are provided) to ensure that the The outside user‘has ho di?ect 02 mod;sie will comply with Part 15 control of transmit modulation. Y¥ l * thia, The Module caninterface to requirements under conditions of codraemr.? 1. excessive data rates or over—modulation External world using GP1Os, CCC " ~ SPVUART interface. The RF IC on module contains its own voltage regulation ciroult. o3 The modular transmitter must have its in case of supply voltage y ~ Own power supply requlation. variation, the voltage will be stabilized. Refer Appendix 5_Block Diagram The modular transmifter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a "unique" antenna coupler {at 04 all connections between the module and T e ji;he Module has Integral PCB— race Antenna. ¥ The antenna, including the cable}. The "professional installation" provision of Section 15.203 is not applicable to modules but can apply to limited Modular approvails under paragraph (b) of this section. The modular transmitter must be tested in a stand—alone configuration, Le., the , bakss . 22 4 The Module is tested in module must not be inside ancother a hh / — — . standalone condition. 05 device during testing for compliance ¥ Refer Appendix 1.Test setup With Part 15 requirements. Uniess the Photos transmitter module will be battery powered, it must comply with the AC

Date: 10/03/2012 The Kroger Co. 11450 Grooms Rd Blue Ash, OH 45242 fine conducted requirements found in Section 15.207. AC or DC power lines and data input/output fines connected to the module must not contain ferrites, untess they will be marketed with the Module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting Equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be Unmodified and commercially available ({see Section 15.31(1p. The modular transmitter must be equipped with sither a permanently affixed label or must be capable of electronically displaying its FCC Identification number. {(A) If using a permanentfly affixed label, the modular transmifter must be labeled with its own FCC identiffication number, and, If the FCC identffication number is not visible when the module is installed inside ancother device, then the oulside of the device into which the module is Installed must also display a label referring to The enclosed module. This exterior label can use wording such as the following: "Confains Transmilter Module FCC ID: XYZMODEL1" or "Contains FCC The Module will be labeled with IFs: FCC 1D number. When module XYZMODELT." Any similar wording is installed inside the End That expresses the same meaning may be Product and label is not visible, Y¥ used. Labeling instruction is provided The Grantes may either provide such a in User Manual for OEM. Refer label, an example of which must be Appendix 4_Label Diagram included in the application for equipment authorization, or, must provide adequate Instructions along with the module which explain This requirement. In the latter case, a copy of these instructions must be included in the Application for equipment authorization. (B) If the modular transmitter uses an efectronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmilter or on the Device in which it is instailed. If the module is instailed inside another device, then the cutside of the device into which the module

Date: 10/03/2012 The Kroger Co. 11450 floms Rd Blue Ash, OH 45242 is installed must display a label referring to the enclosed Module. This exterior label can use wording such as the following: "Contains FCC certified fransmitter module(s}." Any similar wording that expresses the same Meaning may be used. The user manual must include instructions on how to access the Electronic display. A copy of these instructions Must be included in the application for equipment authorization. The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a The Module is compftant with complete transmitter and the manufacturer applicable FCC Rules. 07 must provide adequate instructions along Instructions are provided in User with the module to explain any such Manual. Refer Appendix 9_User Requirements. A copy of these Manual Instructions must be included in the application for equipment authorization. The unit is compliant with the RF The modular transmitter must comply ixpesure requsrements{cef Paris . & 5.247 and 21091. Refer 08 with any applicable RF exposure Appendix 10)Maximurm requirements in its final configuration permissible exposure information. A limited modular approval may be granted for single or spift modular transmifters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the fransmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is dernonstrated only for particular product configurations. The applicant for certification must state how contrel of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured Sincerely, %u;m é@w(m Gion Perkins R&D Manager The Kroger €o.


Document Created: 2012-10-04 15:18:16
Document Modified: 2012-10-04 15:18:16
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC