report

FCC ID: PAXPMV107M

Test Report

Download: PDF
FCCID_612872

A-014-05-C Page 1 of 18 FCC ID: PAXPMV107M KANSAI ELECTRONIC INDUSTRY DEVELOPMENT CENTER HEAD OFFICE IKOMA TESTING LABORATORY 6-8-7 NISHITENMA 12128 TAKAYAMA-CHO KITA-KU OSAKA 530-0047 JAPAN IKOMA-CITY NARA 630-0101 JAPAN Corporate Juridical Person TEST REPORT Report No.A-014-05-C Date: 4 October 2005 This test report is to certify that the tested device properly complies with the requirements of: FCC Rules and Regulations Part 15 Subpart C Intentional Radiators. All the tests necessary to show compliance to the requirements were performed and these results met the specifications of requirement. The results of this report should not be construed to imply compliance of equipment other than that, which was tested. Unless the laboratory permission, this report should not be copied in part. 1. Applicant Company Name : Pacific Industrial Co., Ltd. TPMS DEPT. Mailing Address : Godo-cho, Ampachi, GIFU, 503-2397 2. Identification of Tested Device Type of Device : Transmitter Kind of Equipment Authorization : : DoC : Certification : Verification FCC ID : PAXPMV107M Device Name : Tire Pressure Monitoring System Transmitter Trade Name : PACIFIC Model Number : PMV-107M Serial Number : No.1 : Production : Pre-production : Prototype Date of Manufacture : September 2005 3. Test Items and Procedure : AC Power Line Conducted Emission Measurement : Radiated Emission Measurement : Emission Bandwidth Measurement Above all tests were performed under: ANSI C63.4 – 2003 : without deviation, : with deviation (details are found inside of this report) 4. Date of Test Receipt of Test Sample : 27 September 2005 Condition of Test Sample : : Damage is not found on the set. : Damage is found on the set. (Details are described in this report) Test Completed on : 30 September 2005 Seiichi Izumi General Manager / Ikoma Testing Laboratory KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 2 of 18 FCC ID: PAXPMV107M Table of Contents 0. LABORATORY ACCREDITATION AND MEASUREMENT UNCERTAINTY .........................3 0.1. Laboratory Accreditation................................................................................................................3 0.2. Measurement Uncertainty ..............................................................................................................3 1. CERTIFICATION OF THE COMPLIANCE ...................................................................................3 2. GENERAL INFORMATION ..............................................................................................................4 2.1. Product Description........................................................................................................................4 2.2. Description for Equipment Authorization ......................................................................................5 2.3. Test Facility ....................................................................................................................................5 3. TESTED SYSTEM...............................................................................................................................6 3.1. Test Mode.......................................................................................................................................6 3.2. Characteristics of transmitting train ...............................................................................................6 3.3. Characterization and condition of EUT System .............................................................................8 4. RADIATED EMISSION MEASUREMENT .....................................................................................9 4.1. Test Procedure ................................................................................................................................9 4.2. Test Results ..................................................................................................................................10 5. EMISSION BANDWIDTH MEASUREMENT...............................................................................16 5.1. Test Configuration........................................................................................................................16 5.2. Test Results ..................................................................................................................................16 6. USED TEST EQUIPMENTS AND CALIBRATION STATUS......................................................18 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 3 of 18 FCC ID: PAXPMV107M 0. LABORATORY ACCREDITATION AND MEASUREMENT UNCERTAINTY 0.1. Laboratory Accreditation KEC is accredited by the National Voluntary Laboratory Accreditation Program (NVLAP) for the specific scope of accreditation under Lab Code: 200207-0. When the test report concerns with the NVLAP accreditation test, the first page of the test report is signed by NVLAP Approved Signatory accompanied by the NVLAP logo. The report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. 0.2. Measurement Uncertainty The result of a measurement is only an approximation or estimate of the value of a specific quantity. And thus the measured is complete only when a statement of uncertainty is given. KEC quotes Measurement Uncertainty (U) of +/- 4.9dB for Radiated Emissions of +/- 2.2dB for Conducted Emissions 1. CERTIFICATION OF THE COMPLIANCE This test report is to certify that the tested device properly complies with the requirements of FCC Rules and Regulations Part 15 Subpart C Intentional Radiators. KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 4 of 18 FCC ID: PAXPMV107M 2. GENERAL INFORMATION 2.1. Product Description The PACIFIC Model No.: PMV-107M (referred to as the EUT in this report) is a Tire Pressure Monitoring System Transmitter for cars. 1) Technical Specifications Operating frequency range : 314.98MHz Type of antenna : Internal Antenna Type of Emission : F2D (FSK) Frequency deviation : 40kHz (Nominal) 2) Contained Oscillators SAW : 314.68MHz 3) Rated Power Supply : DC3V (Lithium battery) KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 5 of 18 FCC ID: PAXPMV107M 2.2. Description for Equipment Authorization (1) Type of device : Intentional Radiators (2) Reference Rule and Specification : FCC Rule Part 15 Subpart C, Section 15.231 Periodic operation in the band 40.66 – 40.70MHz and above 70MHz Section 15.207 Section 15.209 Section 15.231 (c) Section 15.231 (e) (3) Kind of Equipment Authorization : DoC Certification Verification (4) Procedure of Application : Original Equipment Modification (5) Highest Frequency used in the Device : 314.98MHz (6) Upper Frequency of Radiated Emission Measurement Range : 1000MHz 2000MHz 5000MHz Tenth harmonics of the highest fundamental frequency 2.3. Test Facility All tests described in this report were performed by: Name: KANSAI ELECTRONIC INDUSTRY DEVELOPMENT CENTER (KEC) IKOMA TESTING LABORATORY Open Area Test Site No.1 No.4 Anechoic Chamber No.1 No.3 Shielded Room No.1 No.2 No.4 No.6 Address: 12128, Takayama-cho Ikoma-city, Nara, 630-0101 Japan These test facilities have been filed with the FCC under the criteria of ANSI C63.4-2003. The KEC has been accredited by the NVLAP (Lab. Code: 200207-0) based on ISO/IEC 17025. Also the laboratory has been authorized by TUV Product Service (GER) and TUV Rheinland (GER) based on their criteria for testing laboratory (ISO/IEC 17025). EMC M.C. Anechoic Chamber No.3 has been filed with the Industry Canada under the criteria of RSS212, issue 1. (File number : IC4149-3) KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 6 of 18 FCC ID: PAXPMV107M 3. TESTED SYSTEM 3.1. Test Mode Continuously transmitted mode. [Note] The EUT was operated continuously in measurement. In the measurement of radiated emission. The EUT was placed horizontally or vertically on the test table. The data of operation modes that produce the maximum emission were reported at each frequency. 3.2. Characteristics of transmitting train The transmission of EUT is less than 1.0 second and the intervals are greater than 10 seconds. See plot figure 1 to 4. Figure 1. normal transmission KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 7 of 18 FCC ID: PAXPMV107M - Continued - Figure 2. Alert status transmission 1 Figure 3. Alert status transmission 1 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 8 of 18 FCC ID: PAXPMV107M - Continued - Figure 4. Transmission interval [Note] (1) In figure 3, the duration of each transmission is not greater than one second. (2) In figure 4, the silent period between transmissions shall be at least 30 times the duration of the transmission but in no case less than 10 seconds. 3.3. Characterization and condition of EUT System : normal, : not normal (that is ) KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 9 of 18 FCC ID: PAXPMV107M 4. RADIATED EMISSION MEASUREMENT 4.1. Test Procedure (1) Configure the EUT System in accordance with ANSI C63.4-2003 section 8. : without deviation, : with deviation (details are found below) See also the block diagram and the photographs of EUT System configuration in this report. (2) If the EUT system is connected to a public power network, all power cords for the EUT System are connected the receptacle on the turntable. (3) Warm up the EUT System. (4) Activate the EUT System and run the prepared software for the test, if necessary. (5) To find out the emissions of the EUT System, preliminary radiated measurement are performed at a closer distance than that specified for final radiated measurement using the spectrum analyzer (*1) and the broad band antenna. In the frequency above 1GHz, it is performed using the spectrum analyzer (*2) and the horn antenna. (6) To find out an EUT System condition, which produces the maximum emission, the configuration of EUT System, the position of the cables, and the operation mode, are changed under normal usage of the EUT. (7) The spectrums are scanned from 30MHz to the upper frequency of measurement range, and collect the six highest emissions minimum on the spectrum analyzer relative to the limits in the whole range. (8) In final compliance test, the six highest emissions minimum, recorded above, are measured at the specified distance using the broad band antenna or the tuned dipole antenna and the test receiver (*3). In the frequency above 1GHz, the measurements are performed by the horn antenna and the test receiver (*4). the spectrum analyzer (*2) with pre-amplifier. [Note] (*1) Spectrum Analyzer Set Up Conditions Frequency range : 30 – 1000MHz Resolution bandwidth : 100kHz Detector function : Peak mode (*2) Spectrum Analyzer Set Up Conditions Frequency range : 1GHz – Upper frequency of measurement range Resolution bandwidth : 1MHz Video bandwidth : 1MHz Attenuator : 10dB Detector function : Peak mode (*3) Test Receiver Set Up Conditions Detector function : Quasi – Peak or Peak IF bandwidth : 120kHz (*4) Test Receiver Set Up Conditions Detector function : Average IF bandwidth : 1MHz KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 10 of 18 FCC ID: PAXPMV107M 4.2. Test Results Measurement Distance : 3m : 10m Antenna Conversion Meter Reading Maximum Limit Margin Measured Factor Factor Horizontal Vertical Field Peak Average for Frequency (*1) (*2) Polarization Polarization Strength Limit (MHz) (dB/m) (dB) (dBµV) (dBµV) (dBµV/m) (dBµV/m) (dBµV/m) (dB) [ Peak Detector Measurement ] [ Fundamental ] 314.94 20.9 - 60.4 54.1 81.3 87.7 67.7 6.4 [ Harmonics ] 629.89 26.9 - 22.9 22.6 49.8 67.7 47.7 17.9 945.00 31.3 - 11.7 9.0 43.0 67.7 47.7 24.7 [ Average Detector Measurement ] [ Fundamental ] 314.94 20.9 -16.7 60.4 54.1 64.6 - 67.7 3.1 [ Harmonics ] 629.89 26.9 -16.7 22.9 22.6 33.1 - 47.7 14.6 945.00 31.3 -16.7 11.7 9.0 26.3 - 47.7 21.4 [Note] The restrict band data below 1GHz, see the figure 5. 30 – 1000MHz spectrum chart. KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 11 of 18 FCC ID: PAXPMV107M - Continued - Restricted Band Above 1GHz Measured Antenna Conversion Meter Reading Maximum Limit Margin Frequency Factor Factor Horizontal Vertical Field Peak Average for (*1) (*2) Polarization Polarization Limit ( MHz ) ( dB/m ) (dB) (dBµV) (dBµV) (dBµV/m) (dBµV/m) (dBµV/m) ( dB ) [ Peak Detector Measurement ] [ Harmonics ] 1259.75 -12.6 - 64.2 61.7 51.6 74.0 54.0 22.4 1574.76 -12.2 - 65.8 61.0 53.6 74.0 54.0 20.4 1889.55 -10.7 - 60.2 55.5 49.5 74.0 54.0 24.5 2204.06 -10.4 - 59.7 57.8 49.3 74.0 54.0 24.7 2519.63 -9.9 - 53.4 49.4 43.5 74.0 54.0 30.5 2834.57 -9.3 - 50.3 49.4 41.0 74.0 54.0 33.0 3149.71 -8.6 - <46.0 <46.0 <37.4 74.0 54.0 >36.6 [ Average Detector Measurement ] [ Harmonics ] 1259.75 -12.6 64.2 61.7 51.6 - 54.0 2.4 1574.76 -12.2 -16.7 65.8 61.0 36.9 - 54.0 17.1 1889.55 -10.7 -16.7 60.2 55.5 32.8 - 54.0 21.2 2204.06 -10.4 -16.7 59.7 57.8 32.6 - 54.0 21.4 2519.63 -9.9 -16.7 53.4 49.4 26.8 - 54.0 27.2 2834.57 -9.3 -16.7 50.3 49.4 24.3 - 54.0 29.7 3149.71 -8.6 -16.7 <46.0 <46.0 <20.7 - 54.0 >33.3 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 12 of 18 FCC ID: PAXPMV107M Test data in Graph Figure 5. 30 – 1000MHz spectrum chart [Note] This spectrum chart is the result of Exploratory radiated emission measurement by using the spectrum analyzer. The result of Final radiated emission measurement is shown in the table of previous page. KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 13 of 18 FCC ID: PAXPMV107M - Continued - [Remark] (*1) : Antenna Factor includes the cable loss, above 1GHz, antenna factor includes both of the cable loss and pre-amplifier gain. (*2) : Conversion Factor, See figure 6 and 7 (the picture of spectrum analyzer) and See Page 14, Calculation of Conversion Factor (Peak detector to Average). (*3) : If the measurement value with the peak detector meets the average limits, the measurement with average detector is omitted. In FCC rule, the limit of measurement of radiated emission above 1GHz is regulated on the average value. Therefore, the average value above 1GHz was determined by using a reduced the video bandwidth of spectrum analyzer to obtain the average value in this case spectrum analyzer set up condition. Resolution Bandwidth : 1MHz Video Bandwidth : 30Hz Detector function : Peak detector [Note] (1) * mark in Measured Frequency : Measured with the tuned dipole antenna. No mark in Measured Frequency : Measured with the broadband antenna. (2) All emission not reported were less than 10dBµV at meter reading. [Calculation method] Maximum Field Strength (dBµV/m) = Meter Reading (at maximum level of Horizontal or Vertical) (dBµV) + Antenna Factor (dB/m) [Calculation of Limit (Average detector)] Fundamental L = 20log (16.667 × F – 2833.333) Where, L: Limit [dBµV/m], F: Frequency [MHz] L = 67.7 [dBµV/m] at F=314.95[MHz] Spurious Emission L = 67.7 – 20 = 47.7 [dBµV/m] Above 1000 MHz, the limit is replaced at 54 dBµV/m. [Environment] Temperature: 23 °C Humidity: 60 % [Tested Date / Tester] 29 September 2005 Signature Hironobu Matsuyama KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 14 of 18 FCC ID: PAXPMV107M - Continued - [Calculation of Conversion Factor (Peak detector to Average)] In accordance with ANSI C63.4-2003 section 13.1.4.2, The EUT's transmitting pulse modulated emissions, therefore the average level of emissions are found by measuring peak level of the emission and correcting them with the duty cycle. From Figure 6. The value of the sum of the pulse widths in one period : 14.5 [msec] The length of the period : 100.0 [msec] As the EUT pulse train exceeds 100ms, calculate the duty cycle by averaging the sum of the pulse widths over the width with the highest average value. Then, Conversion Factor PEAK to AVERAGE is calculated as follows. Conversion Factor 14.5 [msec] (dB) = 20 Log ( Duty cycle ) = 20 Log PEAK to AVERAGE 100.0 [msec] = -16.7 (dB) n The value of the sum of the pulse widths in one period ∑t n =1 n Duty cycle = The length of period (T) [Sample Calculation at conversion Peak to Average] Field Strength (dBµV/m) = Meter Reading (at Maximum level of horizontal or vertical) (dBµV) + Antenna Factor (dB/m) + Conversion Factor (dB) KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 15 of 18 FCC ID: PAXPMV107M - Continued - Figure 6 Figure 7 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 16 of 18 FCC ID: PAXPMV107M 5. EMISSION BANDWIDTH MEASUREMENT 5.1. Test Configuration Receiving Antenna Spectrum EUT Analyzer GP- IB Recording Device(PC) 5.2. Test Results Measured emission bandwidth = 450kHz See next Figure 8 (the picture of spectrum analyzer) [Note] Emission Bandwidth was determined at the points 20dB down from the modulated carrier. Spectrum Analyzer Setting: Center Frequency = 315.00MHz Frequency Span = 200kHz/div. Resolution Bandwidth = 100kHz Video Bandwidth = 100kHz Sweep Time = 5m sec Trace Mode : MAX. HOLD [Environment] Temperature: 25°C Humidity: 54% [Calculation of Limit] Limit of Emission bandwidth = 315.00 MHz × 0.25% = 787.50kHz [Tested Date / Tester] 30 September 2005 Signature Hironobu Matsuyama KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 17 of 18 FCC ID: PAXPMV107M - Continued - Figure 8 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan

A-014-05-C Page 18 of 18 FCC ID: PAXPMV107M 6. USED TEST EQUIPMENTS AND CALIBRATION STATUS KEC Test Last Next Equipment Manufacturer Model No. Specifications Control Item Cal. Cal. No. (*) Test Rohde & ESHS10 Frequency Range FS-83 N/A 2005/2 2006/2 Receiver Schwarz 9kHz – 30MHz ESVS10 Frequency Range FS-66 2 2005/3 2006/3 20MHz – 1.0GHz Spectrum Hewlett 8564E Frequency Range SA-39 2,3 2005/4 2006/4 Analyzer Packard 30Hz – 40GHz Pre-amplifier Hewlett 8449B Frequency Range AM-52 2 2005/2 2006/2 Packard 1GHz – 26.5GHz Biconical Schwarzbeck BBA9106 Frequency Range AN-180 2 2005/2 2006/2 Antenna 30MHz – 300MHz Log- Schwarzbeck UHALP9108A Frequency Range AN-215 2 2005/2 2006/2 Periodic 300MHz – 1GHz Antenna Tuned Kyoritsu KBA-511AS Frequency Range AN-135 2 2005/2 2007/2 Dipole 25MHz – 500MHz Antenna KBA-611S Frequency Range AN-137 2 2005/2 2007/2 500MHz – 1GHz Horn Raven 92888-2 Frequency Range AN-211 2 2003/9 2005/9 Antenna 1GHz – 2GHz 91889-2 Frequency Range AN-212 2 2003/9 2005/9 2GHz – 5GHz LISN Kyoritsu KNW-407 Frequency Range FL-107 N/A 2005/7 2006/7 for EUT 150kHz – 30MHz LISN for Kyoritsu KNW-242 Frequency Range FL-110 N/A 2005/7 2006/7 Peripheral 10kHz – 30MHz [Note] Test Item (*): 1: Conducted Emission Measurement 2: Radiated Emission Measurement 3: Bandwidth Measurement N/A: Not Applicable The overall program of calibration and verification of equipment is designed and operated so as to ensure that measurements made by KEC are traceable to national standards of measurement or equivalent abroad. KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan


Document Created: 2005-10-11 15:59:57
Document Modified: 2005-10-11 15:59:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC