User Manual

FCC ID: PANCM8822CU

Users Manual

Download: PDF

FCCID_4353244

(OEM) Integrator has to assure compliance of the entire end-product incl. the integrated RF Module.
For 15 B (§15.107 and if applicable §15.107) compliance, the host manufacturer is required to
show compliance with 15 while the module is installed and operating.

Furthermore the module should be transmitting and the evaluation should confirm that the module's
intentional emissions (15C) are compliant (fundamental / out-of-band). Finally the integrator has
to apply the appropriate equipment authorization (e.g. Verification) for the new host device per
definition in §15.101.

Integrator is reminded to assure that these installation instructions
will not be made available to the end user of the final host device.

- Module isintegrated" hasto be labelled
The final host device, into which this RF
with an auxilliary lable stating the FCC IDofthe RF Module,
such as "Contains FCC ID:

"This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1)this devicemay not cause harmful interference, and
(2)this devicemust accept any interference received, including
interference thatmay cause undesired operation."

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
--Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

Module statement
The single-modular transmitter is a self-contained, physically delineated, component
for which compliance can be demonstrated independent of the host operating
conditions, and which complies with all eight requirements of § 15.212(a)(1) as
summarized below.
1) The radio elements have the radio frequency circuitry shielded.
2) The module has buffered modulation/data inputs to ensure that the device will
comply with Part 15 requirements with any type of input signal.
3) The module contains power supply regulation on the module.
4) The module contains a permanently attached antenna.
5) The module demonstrates compliance in a stand-alone configuration.
6) The module is labeled with its permanently affixed FCC ID label
7) The module complies with all specific rules applicable to the transmitter, including
all the conditions provided in the integration instructions by the grantee.
8) The module complies with RF exposure requirements.

This transmitter/module must not be collocated or operating in conjunction with any
other antenna or transmitter.

- List of applicable FCC rules FCC Part 15.407, KDB 789033 D02 v02r01; FCC Part 15.247
- Summarize the specific operational use conditions This transmitter/module and its antenna(s) must not be
co-located or operating in conjunction with any other
antenna or transmitter. This information also extends
to the host manufacturer’s instruction manual.

- Limited module procedures not applicable
- Trace antenna designs It is “not applicable” as trace antenna which is not used on the module.

- RF exposure considerations This equipment complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment. This compliance to FCC
radiation exposure limits for an uncontrolled environment, and
minimum of 20cm separation between antenna and body.
The host product manufacturer would provide the above information
to end users in their end-product manuals.

- Antennas The module only equipped with antenna connector, the dipole antennas will
be sold with this module.
ANT 1: -0.08dBi (2.412 GHz ~ 2.462 GHz), 3.77 dBi (5.15 GHz ~ 5.25 GHz; 5.725 GHz ~ 5.85 GHz)
ANT 2: -0.46dBi (2.412 GHz ~ 2.462 GHz), 3.3 dBi (5.15 GHz ~ 5.25 GHz; 5.725 GHz ~ 5.85 GHz)

- Label and compliance information The end product must carry a physical label or shall use e-labeling
followed KDB784748D01 and KDB 784748 stating “Contains Transmitter Module FCC ID: PANCM8822CU”.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.

- Additional testing, Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for
the specific rule parts (FCC Part15.407, 15.247)
listed on the grant, and that the host product
manufacturer is responsible for compliance to any
other FCC rules that apply to the host not covered
by the modular transmitter grant of certification.
The final host product still requires Part 15 Subpart
B compliance testing with the modular transmitter
installed when contains digital circuity.

Information on test modes and additional testing requirements.

Information on test modes:
The host manufacturer can use software for access to the test modes. Connected to the
device through the serial port of the host product and control the module. If it does not
work, then the host product manufacturer should coordinate with the module
manufacturer for access to test mode software.

The following provides guidance to host product when installing this module on
how they may verify the end product:
A. If the modular transmitter has been fully tested by the module grantee on the
required number of channels, modulation types, and modes, it should not be
necessary for the host installer to re‐test all the available transmitter modes or
settings. It is recommended that the host product manufacturer, installing the
modular transmitter, perform some investigative measurements to confirm that
the resulting composite system does not exceed the spurious emissions limits or
band edge limits (e.g., where a different antenna may be causing additional
emissions).
B. The testing should check for emissions that may occur due to the intermixing of
emissions with the other transmitters, digital circuitry, or due to physical
properties of the host product (enclosure). This investigation is especially
important when integrating multiple modular transmitters where the
certification is based on testing each of them in a stand‐alone configuration. It is
important to note that host product manufacturers should not assume that
because the modular transmitter is certified that they do not have any
responsibility for final product compliance.
C. If the investigation indicates a compliance concern the host product
manufacturer is obligated to mitigate the issue. Host products using a modular
transmitter are subject to all the applicable individual technical rules as well as
to the general conditions of operation in Sections 15.5, 15.15, and 15.29 to not
cause interference. The operator of the host product will be obligated to stop
operating the device until the interference has been corrected.

Document Created: 2019-07-12 10:06:14
Document Modified: 2019-07-12 10:06:14

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC