Test report 2

FCC ID: PANBT0330

Test Report

Download: PDF
FCCID_459638

FCC ID: PANBT0330 4.7.3 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meters semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10 dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10 dB margin would be re- tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 1 MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 10 Hz for Average detection (AV) at frequency above 1GHz. 4.7.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF920815R01 51 Issued: July 20, 2004

FCC ID: PANBT0330 4.7.5 TEST SETUP For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. Report No.: RF920815R01 52 Issued: July 20, 2004

FCC ID: PANBT0330 4.7.6 TEST RESULTS EUT Bluetooth USB Adapter MODEL BT-0330 FREQUENCY CHANNEL 78 Below 1 GHz RANGE INPUT POWER DETECTOR 120 Vac, 60 Hz Quasi-Peak (SYSTEM) FUNCTION ENVIRONMENTAL 25 deg. C, 65% RH, TESTED BY Long Chen CONDITIONS 991 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 455.71 33.89 QP 46.00 -12.11 2.00 H 226 15.71 18.18 2 601.50 31.95 QP 46.00 -14.05 1.00 H 154 10.68 21.27 3 735.63 38.43 QP 46.00 -7.57 1.00 H 106 15.09 23.34 4 801.72 35.20 QP 46.00 -10.80 1.00 H 67 11.42 23.79 5 867.82 39.14 QP 46.00 -6.86 1.00 H 70 14.54 24.60 6 912.53 36.05 QP 46.00 -9.95 1.50 H 313 10.67 25.39 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 455.71 34.91 QP 46.00 -11.09 2.00 V 190 16.74 18.18 2 601.50 34.35 QP 46.00 -11.65 1.00 V 79 13.08 21.27 3 669.54 32.30 QP 46.00 -13.70 1.00 V 7 10.14 22.16 4 735.63 34.85 QP 46.00 -11.15 1.00 V 106 11.51 23.34 5 801.72 31.52 QP 46.00 -14.48 1.50 V 97 7.73 23.79 6 867.82 33.45 QP 46.00 -12.55 1.50 V 88 8.85 24.60 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. Report No.: RF920815R01 53 Issued: July 20, 2004

FCC ID: PANBT0330 EUT Bluetooth USB Adapter MODEL BT-0330 FREQUENCY CHANNEL 0 1 ~25 GHz RANGE INPUT POWER DETECTOR Peak(PK) 120 Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 25 deg. C, 70% RH, TESTED BY Long Chen CONDITIONS 991 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1602.00 42.23 PK 74.00 -31.77 1.35 H 215 13.66 28.57 2 *2402.00 100.37 PK 1.46 H 261 69.21 31.16 2 *2402.00 65.83 AV 1.46 H 261 34.67 31.16 3 4804.00 51.34 PK 74.00 -22.66 1.08 H 224 13.51 37.83 3 4804.00 16.80 AV 54.00 -37.20 1.08 H 224 -21.03 37.83 4 7206.00 54.38 PK 74.00 -19.62 1.64 H 225 11.00 43.38 4 7206.00 19.84 AV 54.00 -34.16 1.64 H 225 -23.54 43.38 5 9608.00 59.36 PK 74.00 -14.64 1.67 H 57 12.93 46.43 5 9608.00 24.82 AV 54.00 -29.18 1.67 H 57 -21.61 46.43 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1602.00 41.29 PK 74.00 -32.71 1.65 V 107 12.72 28.57 2 *2402.00 95.70 PK 1.70 V 122 64.54 31.16 2 *2402.00 61.16 AV 1.70 V 122 30.00 31.16 3 4804.00 53.25 PK 74.00 -20.75 1.00 V 296 15.42 37.83 3 4804.00 18.71 AV 54.00 -35.29 1.00 V 296 -19.02 37.83 4 7206.00 53.12 PK 74.00 -20.88 1.36 V 75 9.74 43.38 4 7206.00 18.58 AV 54.00 -35.42 1.36 V 75 -24.80 43.38 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The DH3 packet was the worse case duty cycle for a transmit dwell time on a channel, based upon bluetooth theory the transmitter is on 0.625*3 per 197.5 ms per channel. Therefore, the duty cycle be equal to: 20log(1.875/100)= -34.54dB 7. Average value = peak reading –20log(duty cycle) Report No.: RF920815R01 54 Issued: July 20, 2004

FCC ID: PANBT0330 EUT Bluetooth USB Adapter MODEL BT-0330 FREQUENCY CHANNEL 39 1 ~25 GHz RANGE INPUT POWER DETECTOR Peak(PK) 120 Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 25 deg. C, 70% RH, TESTED BY Long Chen CONDITIONS 991 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1628.00 41.30 PK 74.00 -32.70 1.35 H 215 12.71 28.59 2 *2441.00 101.06 PK 1.39 H 79 69.71 31.36 2 *2441.00 66.52 AV 1.39 H 79 35.16 31.36 3 4882.00 50.80 PK 74.00 -23.20 1.07 H 20 12.79 38.01 3 4882.00 16.26 AV 54.00 -37.71 1.07 H 20 -21.75 38.01 4 9764.00 59.08 PK 74.00 -14.92 1.49 H 52 12.70 46.38 4 9764.00 24.54 AV 54.00 -29.46 1.49 H 52 -21.84 46.38 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1628.00 41.82 PK 74.00 -32.18 1.32 V 120 13.23 28.59 2 *2441.00 96.40 PK 1.69 V 195 65.04 31.36 2 *2441.00 61.86 AV 1.69 V 195 30.50 31.36 3 4882.00 53.66 PK 74.00 -20.34 1.02 V 337 15.65 38.01 3 4882.00 19.12 AV 54.00 -34.88 1.02 V 337 -18.89 38.01 4 9764.00 65.56 PK 74.00 -8.44 1.37 V 255 19.18 46.38 4 9764.00 31.02 AV 54.00 -22.98 1.37 V 255 -15.36 46.38 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The DH3 packet was the worse case duty cycle for a transmit dwell time on a channel, based upon bluetooth theory the transmitter is on 0.625*3 per 197.5 ms per channel. Therefore, the duty cycle be equal to: 20log(1.875/100)= -34.54dB 7. Average value = peak reading –20log(duty cycle) Report No.: RF920815R01 55 Issued: July 20, 2004

FCC ID: PANBT0330 EUT Bluetooth USB Adapter MODEL BT-0330 FREQUENCY CHANNEL 78 1 ~25 GHz RANGE INPUT POWER DETECTOR Peak(PK) 120 Vac, 60 Hz (SYSTEM) FUNCTION Average (AV) ENVIRONMENTAL 25 deg. C, 70% RH, TESTED BY Long Chen CONDITIONS 991 hPa ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1653.00 43.83 PK 74.00 -30.17 1.00 H 158 15.23 28.60 2 *2480.00 99.88 PK 1.42 H 258 68.33 31.55 2 *2480.00 65.34 AV 1.42 H 258 33.79 31.55 3 4960.00 50.93 PK 74.00 -23.07 1.58 H 89 12.73 38.20 3 4960.00 16.39 AV 54.00 -37.61 1.58 H 89 -21.80 38.20 4 9920.00 57.97 PK 74.00 -16.03 1.32 H 72 11.37 46.60 4 9920.00 23.43 AV 54.00 -30.57 1.32 H 72 -23.17 46.60 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3M Emission Antenna Table Raw Correction Freq. Limit Margin No. Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1654.00 42.02 PK 74.00 -31.98 1.83 V 252 13.41 28.60 2 *2480.00 95.43 PK 1.69 V 127 63.88 31.55 2 *2480.00 60.89 AV 1.69 V 127 29.34 31.55 3 4960.00 53.88 PK 74.00 -20.12 1.00 V 337 15.68 38.20 3 4960.00 19.34 AV 54.00 -34.66 1.00 V 337 -18.86 38.20 4 9920.00 56.42 PK 74.00 -17.58 1.00 V 343 9.82 46.60 4 9920.00 21.88 AV 54.00 -32.12 1.00 V 343 -24.72 46.60 REMARKS: 1. Emission level(dBuV/m)=Raw Value(dBuV) + Correction Factor(dB) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. “ * “ : Fundamental frequency 6. The DH3 packet was the worse case duty cycle for a transmit dwell time on a channel, based upon bluetooth theory the transmitter is on 0.625*3 per 197.5 ms per channel. Therefore, the duty cycle be equal to: 20log(1.875/100)= -34.54dB 7. Average value = peak reading –20log(duty cycle) Report No.: RF920815R01 56 Issued: July 20, 2004

FCC ID: PANBT0330 4.8 BAND EDGES MEASUREMENT 4.8.1 LIMITS OF BAND EDGES MEASUREMENT Below –20dB of the highest emission level of operating band (in 100kHz RBW). 4.8.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until SPECTRUM ANALYZER FSEK30 100049 Aug. 12, 2004 NOTE: The calibration interval of the above test instruments is 12 months. And the calibrations are traceable to NML/ROC and NIST/USA. 4.8.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz with suitable frequency span including 100 MHz bandwidth from band edge. The band edges was measured and recorded. 4.8.4 DEVIATION FROM TEST STANDARD No deviation Report No.: RF920815R01 57 Issued: July 20, 2004

FCC ID: PANBT0330 4.8.5 EUT OPERATING CONDITION The software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel frequencies individually. 4.8.6 TEST RESULTS The spectrum plots are attached on the following 4 pages. D2 line indicates the highest level, D1 line indicates the 20dB offset below D2. It shows compliance with the requirement in part 15.247(C). NOTE1: The band edge emission plot on the following 1 ~ 2 pages show 48.01dB delta between carrier maximum power and local maximum emission in restrict band (2.3780GHz). The emission of carrier strength list in the test result of channel 0 at the item 4.7.6 is 65.83dBuV/m, so the maximum field strength in restrict band is 65.83- 48.01=17.82dBuV/m which is under 54 dBuV/m limit. NOTE2: The band edge emission plot on the following 3 ~ 4 pages show 48.14dB delta between carrier maximum power and local maximum emission in restrict band (2.4845GHz). The emission of carrier strength list in the test result of channel 78 at the item 4.7.6 is 65.34dBuV/m, so the maximum field strength in restrict band is 65.34-48.14=17.20dBuV/m which is under 54 dBuV/m limit. Report No.: RF920815R01 58 Issued: July 20, 2004

LoxsLsoze—x on modey OEE018N¥Vd ‘CI 004 *RBW 100 kHz Marker 1 [TLl ] *VBW 100 kHz 2.40 dBm Ref 20 dBm *Att 30 dB SWT 10 ms 2.402200000 GHz 20 Marker| 2 [FL 45. 80 <lBm Fio 2l 2eehonhoo «B Marker| 3 [TL 1 D1 2.4 Bm —48l 87 —0 . SYUDUUDUU h Marker]) 4 [Tl 10 145 61. qr |~C 2.378booboo ddE D2 —[17.6 dBin ——20 69 ——30 ——40 4 2 h |——60 ——70 roor ‘oz Ainp :penss; F2 F1 —80 . Center 2.354 GHz 10 MHz/ Span 100 MHz

Loxsigozesx on uodey OEE0ISNYd ‘UI 004 *RBW 100 kHz Marker 1 [Tl ] *VBW 100 kHz —42.30 dBm Ref 20 dBm *Att 30 dB SWT 2.25 s 25.000000000 <Hz 20 EtS DL 2.4 dBm 17.6 dBin 09 rooz ‘oz Ainp ‘penss) 4??L 59‘ 43 Ja Y Start 2.5 GlHz 2.25 GHz/ Stop 25 GHz

LOGL80ze—da on uoder OEEOL8NYd ‘UI 004 *RBW 100 kHz Marker 1 [Tl ] *VBW 100 kHz 1.52 dBm Ref 20 dBm *Att 30 dB SWT 10 ms 2.480000000 GHz 20 Marker| 2 [Tl —46. 62 dBm —1o arasoohao cH x Marker| 3 [Tl ¥ D1 1.52 abm —Bi82 dia —0 —Sovudopte— en Marker| 4 [Tl llo —45,58 dBm 2. 504000p00 GHz D2 —18.48 dém —Pp L9 —BP —l4de 2 4 —s0 l ioib tne ts ——60 ——70 pooz ‘oz Ainp :panss) F2 F1 wuoo 1av —80 Center 2.527 GHz 10 MHz/ Span 100 MHz l5p>

Loxsigozesx on uodey OEE0ISNYd ‘UI 004 *RBW 100 kHz Marker 1 [Tl ] *vBW 100 kHKz —42.72 dBm Ref 20 dEBm *Att 30 dB sSWP 2.25 s 20.365000000 GHz 20 D1 1.52) dBm —0 D2 —[1L8.48 d Bm fas) |——30 ——40 rooz ‘oz Ainp ‘penss) ——70 F2 <— E. —80 Ja Y Start 2.5 CHz 2.25 oHz2/ Stop 25 GHz

FCC ID: PANBT0330 4.9 ANTENNA REQUIREMENT 4.9.1 STANDARD APPLICABLE For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (b), if transmitting antennas of directional gain greater than 6 dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. 4.9.2 ANTENNA CONNECTED CONSTRUCTION The antenna used in this product is chip antenna without antenna connector. The maximum gain of this antenna is 0dBi. Report No.: RF920815R01 63 Issued: July 20, 2004

FCC ID: PANBT0330 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: RF920815R01 64 Issued: July 20, 2004

FCC ID: PANBT0330 RADIATED EMISSION TEST Report No.: RF920815R01 65 Issued: July 20, 2004

FCC ID: PANBT0330 6 INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025, Guide 25 or EN 45001: USA FCC, NVLAP, UL Germany TUV Rheinland Japan VCCI Norway NEMKO Canada INDUSTRY CANADA , CSA R.O.C. CNLA, BSMI, DGT Netherlands Telefication Singapore PSB , GOST-ASIA(MOU) Russia CERTIS(MOU) Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26052943 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety/Telecom Lab: Linko RF Lab. Tel: 886-3-3183232 Tel: 886-3-3270910 Fax: 886-3-3185050 Fax: 886-3-3270892 Email: service@mail.adt.com.tw Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report Format Version 1.0 Report No.: RF920815R01 66 Issued: July 20, 2004


Document Created: 2004-08-06 19:02:32
Document Modified: 2004-08-06 19:02:32
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC