test report

FCC ID: PAGTR-026A

Test Report

Download: PDF
FCCID_4285969

TEST REPORT Reference No..................... : WTD19S04027070W FCC ID.............................. : PAGTR-026A Applicant.......................... : KAB Enterprise Co., Ltd. Address............................ : 21F, -1, No.33, Sec. 1, Minsheng Rd., Banqiao Dist., New Taipei City 220, Taiwan Manufacturer.................... : Verdant Electronics(Dong Guan) Co., Ltd. Address............................ : Langxie Administrative District, Qiaotou, Dongguan City, Guang Dong Sheng, China Product.............................. : Remote Controller Model(s)........................ : TR-026A Standards......................... : FCC CFR47 Part 15 Section 15.231:2019 Date of Receipt sample.... : 2019-04-26 Date of Test...................... : 2019-04-27 to 2019-05-15 Date of Issue.................... : 2019-05-16 Test Result....................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Test Site/Test Location: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Tel :+86-755-83551033 Fax:+86-755-83552400 Compiled by: Approved by: Robin Zhou /Test Engineer Philo Zhong / Manager Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Page 1 of 27

Reference No.: WTD19S04027070W Page 2 of 27 1 Laboratories Introduction Waltek Services (Shenzhen) Co., Ltd is a professional third-party testing and certification laboratory with multi-year product testing and certification experience, established strictly in accordance with ISO/IEC 17025 requirements, and accredited by ILAC (International Laboratory Accreditation Cooperation) member. A2LA (American Association for Laboratory Accreditation, the certification number is 4243.01) of USA, CNAS (China National Accreditation Service for Conformity Assessment, the registration number is L3110) of China.Meanwhile, Waltek has got recognition as registration and accreditation laboratory from EMSD (Electrical and Mechanical Services Department), and American Energy star, FCC(The Federal Communications Commission), CEC(California energy efficiency), ISED (Innovation, Science and Economic Development Canada). It’s the strategic partner and data recognition laboratory of international authoritative organizations, such as Intertek(ETL-SEMKO), TÜV Rheinland, TÜV SÜD, etc. Waltek Services (Shenzhen) Co., Ltd is one of the largest and the most comprehensive third party testing laboratory in China. Our test capability covered four large fields: safety test. ElectroMagnetic Compatibility(EMC), and energy performance, wireless radio. As a professional, comprehensive, justice international test organization, we still keep the scientific and rigorous work attitude to help each client satisfy the international standards and assist their product enter into globe market smoothly. Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 3 of 27 1.1 Test Facility A. Accreditations for Conformity Assessment (International) Country/Region Scope Covered By Scope Note USA FCC ID \ DOC \ VOC 1 Canada IC ID \ VOC 2 Japan MIC-T \ MIC-R - Europe EMCD \ RED - Taiwan NCC - ISO/IEC 17025 Hong Kong OFCA - Australia RCM - India WPC - Thailand NTC - Singapore IDA - Note: 1. FCC Designation No.: CN1201. Test Firm Registration No.: 523476. 2. ISED CAB identifier: CN0013 B.TCBs and Notify Bodies Recognized Testing Laboratory. Recognized Testing Laboratory of … Notify body number TUV Rheinland Intertek Optional. TUV SUD SGS Phoenix Testlab GmbH 0700 Element Materials Technology Warwick Ltd. 0891 Timco Engineering, Inc. 1177 Eurofins Product Service GmbH 0681 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 4 of 27 2 Contents Page 1 LABORATORIES INTRODUCTION 2 1.1 TEST FACILITY 3 2 CONTENTS 4 3 REVISION HISTORY 5 4 GENERAL INFORMATION 6 4.1 GENERAL DESCRIPTION OF E.U.T. 6 4.2 DETAILS OF E.U.T. 6 4.3 TEST MODE 6 5 EQUIPMENT USED DURING TEST 7 5.1 EQUIPMENTS LIST 7 5.2 MEASUREMENT UNCERTAINTY 8 5.3 SUBCONTRACTED 8 6 TEST SUMMARY 9 7 RADIATED SPURIOUS EMISSIONS 10 7.1 EUT OPERATION 10 7.2 TEST SETUP 11 7.3 SPECTRUM ANALYZER SETUP 12 7.4 TEST PROCEDURE 13 7.5 SUMMARY OF TEST RESULTS 14 8 PERIODIC OPERATION 15 9 EMISSION BANDWIDTH 19 9.1 TEST PROCEDURE 19 9.2 TEST RESULT 19 10 ANTENNA REQUIREMENT 20 11 PHOTOGRAPHS – MODEL TR-026A TEST SETUP PHOTOS 21 12 PHOTOGRAPHS - CONSTRUCTIONAL DETAILS 23 12.1 MODEL TR-026A - EXTERNAL PHOTOS 23 12.2 MODEL TR-026A - INTERNAL PHOTOS 26 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 5 of 27 3 Revision History Date of Date of Test report No. Receipt Date of Test Purpose Comment Approved Issue sample 2019-04-27 to WTD19S04027070W 2019-04-26 2019-05-16 original - Valid 2019-05-15 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 6 of 27 4 General Information 4.1 General Description of E.U.T. Product: Remote Controller Model(s): TR-026A Model Difference: N/A Type of Modulation: PCM Frequency Range: 433.99MHz Antenna installation: PCB Printed Antenna Antenna Gain: 0dBi 4.2 Details of E.U.T. Ratings: DC 3V by CR2032 LITHIUM BATTERY 4.3 Test Mode All test mode(s) and condition(s) mentioned were considered and evaluated respectively by performing full tests, the worst data were recorded and reported. Test mode Test channel Transmitting 433.99MHz Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 7 of 27 5 Equipment Used during Test 5.1 Equipments List 3m Semi-anechoic Chamber for Radiation Emissions Last Calibration Item Equipment Manufacturer Model No. Serial No. Calibration Due Date Date 1 Spectrum Analyzer R&S FSP30 100091 2019-04-07 2020-04-06 Broad-band Horn 2 SCHWARZBECK BBHA 9120 D 667 2018-05-18 2019-05-17 Antenna(1-18GHz) Broadband COMPLIANCE 3 PAP-1G18 2004 2019-04-07 2020-04-06 Preamplifier DIRECTION Coaxial Cable 4 Top 1GHz-18GHz EW02014-7 2019-04-07 2020-04-06 (above 1GHz) 5 Spectrum Analyzer R&S FSP40 100501 2018-10-20 2019-10-19 Broad-band Horn BBHA917065 6 SCHWARZBECK BBHA 9170 2018-10-25 2019-10-24 Antenna(18-40GHz) 1 Microwave Broadband 7 SCHWARZBECK BBV 9721 100472 2018-10-25 2019-10-24 Preamplifier (18-40GHz) 8 Cable Top 18-40GHz - 2018-10-25 2019-10-24 3m Semi-anechoic Chamber for Radiation Emissions Last Calibration Item Equipment Manufacturer Model No. Serial No Calibration Due Date Date 1 Test Receiver R&S ESCI 101296 2019-04-07 2020-04-06 Trilog Broadband 2 SCHWARZBECK VULB9160 9160-3325 2019-04-07 2020-04-06 Antenna 3 Active Loop Antenna Beijing Dazhi ZN30900A - 2019-04-07 2020-04-06 4 Amplifier ANRITSU MH648A M43381 2019-04-07 2020-04-06 5 Cable HUBER+SUHNER CBL2 525178 2019-04-07 2020-04-06 Coaxial Cable TYPE16 2018-09-12 2019-09-11 6 Top - (below 1GHz) (13M) Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 8 of 27 RF Conducted Testing Last Calibration Item Equipment Manufacturer Model No. Serial No. Calibration Due Date Date 1. Spectrum Analyzer R&S FSL6 100959 2018-09-12 2019-09-11 2 Coaxial Cable Top 10Hz-30GHz - 2018-09-12 2019-09-11 3 Antenna Connector* Realacc 45RSm - 2018-09-12 2019-09-11 GDCB-3G-N- 4 DC Block Gwave 140307001 2018-09-12 2019-09-11 SMA “*”: The temporary antenna connector is soldered on the PCB board in order to perform conducted tests and this temporary antenna connector is listed in the equipment list. 5.2 Measurement Uncertainty Parameter Uncertainty Radio Frequency ± 1 x 10-6 RF Power ± 1.0 dB RF Power Density ± 2.2 dB ± 5.03 dB (30M~1000MHz) Radiated Spurious Emissions test ± 5.47 dB (1000M~25000MHz) Confidence interval：95%. Confidence factor:k=2 5.3 Subcontracted Whether parts of tests for the product have been subcontracted to other labs: Yes No If Yes, list the related test items and lab information: Test Lab: N/A Lab address: N/A Test items: N/A Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 9 of 27 6 Test Summary Test Items Test Requirement Result Conducted Emissions 15.207 N/A* 15.205(a) Radiated Spurious Emissions 15.209 Pass 15.231(a) Periodic Operation 15.231(a) Pass Emission Bandwidth 15.231(c) Pass Antenna Requirement 15.203 Pass Note: Pass=Compliance; NC=Not Compliance; NT=Not Tested; N/A=Not Applicable *: The EUT is only powered by battery, no need to evaluate AC Power Conducted Emission. Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 10 of 27 7 Radiated Spurious Emissions Test Requirement: FCC Part15 Paragraph 15.231(a), 15.209, 15.205 Test Method: ANSI C63.10:2013 Test Result: PASS Measurement Distance: 3m Limit: Field Strength Field Strength Fundamental Field Strength Field Strength of Spurious of Spurious Frequency of Fundamental of Fundamental Emission Emission (MHz) (uV/m) (dBuV/m) (uV/m) (dBuV/m) 44.66-40.70 2250 67 225 47 70-130 1250 62 125 42 130-174 1250 to 3750* 62 to 71.48* 125 to 375* 42 to 51.48* 174-260 3750 71.48 375 51.48 260-470 3750 to 12500* 71.48 to 81.94* 375 to 1250* 51.48 to 61.94* Above 470 12500 81.94 1250 61.94 * linear interpolations 7.1 EUT Operation Operating Environment : Temperature: 23.5 C Humidity: 54.6% RH Atmospheric Pressure: 101.7kPa Test Voltage: DC 3V by Battery EUT Operation : The test was performed in Transmitting mode, the test data were shown in the report. Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 11 of 27 7.2 Test Setup The radiated emission tests were performed in the 3m Semi- Anechoic Chamber test site, using the setup accordance with the ANSI C63.10:2013. The test setup for emission measurement below 30MHz. Semi-anechoic 3m Chamber Turn Table From 0°to 360° 3m EUT Turn Table 0.8m PC Spectrum AMP Combining System Analyzer Network The test setup for emission measurement from 30 MHz to 1 GHz. Semi-anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0°to 360° 3m EUT 0.8m Turn Table PC Spectrum AMP Combining System Analyzer Network Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 12 of 27 The test setup for emission measurement above 1 GHz. Anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0°to 360° 3m EUT 1.5m Turn Table Absorbers PC Spectrum AMP Combining System Analyzer Network 7.3 Spectrum Analyzer Setup Below 30MHz Sweep Speed .............................................. Auto IF Bandwidth ................................................ 10kHz Video Bandwidth.......................................... 10kHz Resolution Bandwidth.................................. 10kHz 30MHz ~ 1GHz Sweep Speed .............................................. Auto Detector ..................................................... PK Resolution Bandwidth .................................. 100kHz Video Bandwidth.......................................... 300kHz Above 1GHz Sweep Speed .............................................. Auto Detector ..................................................... PK Resolution Bandwidth .................................. 1MHz Video Bandwidth.......................................... 3MHz Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 13 of 27 7.4 Test Procedure 1. The EUT is placed on a turntable. For below 1GHz, the EUT is 0.8m above ground plane; For above1GHz, the EUT is 1.5m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is moved from 1m to 4m to find out the maximum emissions. The spectrum was investigated from the lowest radio frequency signal generated in the device, without going below 9 kHz, up to the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Repeat above procedures until the measurements for all frequencies are complete. 7. The radiation measurements are tested under 3-axes(X, Y, Z) position(X denotes lying on the table, Y denotes side stand and Z denotes vertical stand), After pre-test, It was found that the worse radiation emission was get at the X position. So the data shown was the X position only. Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 14 of 27 7.5 Summary of Test Results Test Frequency: 9 kHz~30 MHz The measurements were more than 20 dB below the limit and not reported. Test Frequency: 30 MHz ~ 5 GHz Test Channel: 433.99MHz FCC Part Receiver Turn RX Antenna Corrected Corrected 15.231/15.209/205 Frequency Reading table Amplitude Factor (PK) Angle Height Polar (PK) Limit Margin (dBμV/ (MHz) (dBμV) Degree (m) (H/V) (dB/m) (dBμV/m) (dB) m) 433.99 85.41 310 1.8 H -7.08 78.33 100.83 -22.50 433.99 67.68 247 1.5 V -7.08 60.60 100.83 -40.23 867.98 32.80 187 1.9 H 2.63 35.43 80.83 -45.40 867.98 31.47 146 1.1 V 2.63 34.10 80.83 -46.73 1300.63 61.12 195 1.5 H -14.89 46.23 74.00 -27.77 1300.63 56.87 347 1.3 V -14.89 41.98 74.00 -32.02 1750.04 51.65 76 1.9 H -13.16 38.49 74.00 -35.51 1750.04 61.96 39 1.4 V -13.16 48.80 74.00 -25.20 AV = Peak +20Log10 (duty cycle) =PK+ (-11.79) [refer to section 8 for more detail] FCC Part 15.231/209/205 RX Duty cycle Calculated Frequency PK Antenna Factor AV Limit Margin Polar (MHz) (dBμV/m) (H/V) (dB) (dBμV/m) (dBμV/m) (dB) 433.99 78.33 H -11.79 66.54 80.83 -14.29 433.99 60.60 V -11.79 48.81 80.83 -32.02 867.98 35.43 H -11.79 23.64 60.83 -37.19 867.98 34.10 V -11.79 22.31 60.83 -38.52 1300.63 46.23 H -11.79 34.44 54.00 -19.56 1300.63 41.98 V -11.79 30.19 54.00 -23.81 1750.04 38.49 H -11.79 26.70 54.00 -27.30 1750.04 48.80 V -11.79 37.01 54.00 -16.99 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 15 of 27 8 Periodic Operation The duty cycle was determined by the following equation: To calculate the actual field intensity, The duty cycle correction factor in decibel is needed for later use and can be obtained from following conversion Duty Cycle(%)=Total On interval in a complete pulse train/ Length of a complete pulse train * % Duty Cycle Correction Factor(dB)=20 * Log10(Duty Cycle(%)) Total transmission time(ms) 0.18*47+(0.18*12+0.54*4)*4=25.74 Length of a complete transmission period(ms) 100.00* Duty Cycle(%) 25.74 Duty Cycle Correction Factor(dB) -11.79 (* Note: the transmitter operates for longer than 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum value. So the Length of a complete transmission period=100ms) Refer to the duty cycle plot (as below) Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 16 of 27 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 17 of 27 Pulse 1 Pulse 2 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 18 of 27 Pulse 3 FCC Part15.231 (a) (1) A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. (2)A transmitter activated automatically shall cease transmission within 5 seconds after activation. Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 19 of 27 9 Emission Bandwidth Test Requirement: FCC Part15.231(c) Test Method: FCC Part15.231(c) Limit The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900 MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the center frequency. 9.1 Test Procedure 1. The transmitter output (antenna port) was connected to the spectrum analyzer.EUT and its simulators are placed on a table, let EUT working in test mode, then test it. 2. The bandwidth of the fundamental frequency was measure by spectrum analyser with 10 kHz RBW and 30 kHz VBW. The 20 dB bandwidth was recorded. 9.2 Test Result Frequency 20dB Bandwidth 99% Bandwidth Limit Result (MHz) Emission(kHz) Emission(kHz) (kHz) 433.99 53.40 138.00 1084.98 Compliance Limit=Center Frequency*0.25% Test Plot Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 20 of 27 10 Antenna Requirement An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of §15.211, §15.213, §15.217, §15.219, or §15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with §15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this part are not exceeded. For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. Result: The EUT has one PCB Printed Antenna, the gain is 0 dBi. meets the requirements of FCC 15.203. PCB Printed Antenna Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 21 of 27 11 Photographs – Model TR-026A Test Setup Photos Below 30MHz From 30MHz to 1GHz Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 22 of 27 Above 1GHz Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 23 of 27 12 Photographs - Constructional Details 12.1 Model TR-026A - External Photos Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 24 of 27 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 25 of 27 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 26 of 27 12.2 Model TR-026A - Internal Photos PCB Printed Antenna Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

Reference No.: WTD19S04027070W Page 27 of 27 ======End of Report====== Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn


Document Created: 2019-05-21 10:07:36
Document Modified: 2019-05-21 10:07:36
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC