test report

FCC ID: PADWF120

Test Report

Download: PDF
FCCID_4446132

CTC Laboratories, Inc. 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel: +86-755- 27521059 Fax: +86-755- 27521011 Http://www.sz-ctc.com.cn TEST REPORT Report No. ····························: GTI20180934F-2 FCC ID··································: PADWF120 Applicant································: Wahoo Fitness LLC Address·································: 90 W. Wieuca Road #110 Atlanta Georgia 30342 United States East West Industries Vietnam LLC Manufacturer··························: NO.27, Street No.2, VSIP 2, Hoa Phu Ward, Thu Dau Mot City, Binh Address·································: Duong Province, Vietnam 84, Viet Nam Product Name························: SMART TRAINER Trade Mark·····························: N.A. Model/Type reference···············: WF120 Listed Model(s) ·······················: / Standard·······························: FCC Rules Part 15.249 ANSI C63.10-2013 Date of receipt of test sample…: 2018-10.20 Date of testing…………………..: 2018-10.21 to 2019-06.26 Date of issue…………………....: 2019.06.27 Result……………………………: PASS Compiled by: (Printed name+signature) Torny Fang Supervised by: ( Printed name+signature) Cary Luo Approved by: ( Printed name+signature) Walter Chen Testing Laboratory Name : CTC Laboratories, Inc. Address : 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China This test report may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CTC. The test results in the report only apply to the tested sample. The test report shall be invalid without all the signatures of testing engineers, reviewer and approver. Any objections must be raised to CTC within 15 days since the date when the report is received. It will not be taken into consideration beyond this limit. The test report merely correspond to the test sample.

Page 2 of 27 Report No.: GTI20180934F-2 Table of Contents Page 1. TEST SUMMARY.................................................................................................................................................... 3 1.1. TEST STANDARDS.......................................................................................................................................................... 3 1.2. REPORT VERSION .......................................................................................................................................................... 3 1.3. TEST DESCRIPTION ........................................................................................................................................................ 4 1.4. TEST FACILITY .............................................................................................................................................................. 5 1.5. MEASUREMENT UNCERTAINTY ........................................................................................................................................ 6 1.6. ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 6 2. GENERAL INFORMATION....................................................................................................................................... 7 2.1. CLIENT INFORMATION ................................................................................................................................................... 7 2.2. GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 7 3. DESCRIPTION OF TEST MODES .............................................................................................................................. 8 4. MEASUREMENT INSTRUMENTS LIST ..................................................................................................................... 9 5. TEST ITEM AND RESULTS ..................................................................................................................................... 11 5.1. AC POWER LINE CONDUCTED EMISSIONS ....................................................................................................................... 11 5.2. 20 DB OCCUPIED BANDWIDTH ..................................................................................................................................... 14 5.3. RADIATED FIELD STRENGTH OF THE FUNDAMENTAL SIGNAL .................................................................................................. 16 5.4. RADIATED SPURIOUS EMISSIONS AND BANDEDGE EMISSION ............................................................................................... 18 5.5. ANTENNA REQUIREMENT ............................................................................................................................................. 25 6. EUT TEST PHOTOS ............................................................................................................................................... 26 7. PHOTOGRAPHS OF EUT CONSTRUCTIONAL ......................................................................................................... 27 CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 3 of 27 Report No.: GTI20180934F-2 1. TEST SUMMARY 1.1. Test Standards The tests were performed according to following standards: FCC Rules Part 15.249: Operation within the bands 902-928 MHz, 2400-2483.5 MHz, 5725-5875 MHz, and 24.0-24.25 GHz. ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices. 1.2. Report version Version No. Date of issue Description 00 2019.06.27 Original CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 4 of 27 Report No.: GTI20180934F-2 1.3. Test Description RSS-210& Test Item Section in CFR 47 Result Test Engineer RSS-Gen AC Power Line Conducted 15.207 RSS-Gen N/A N/A Emissions 20dB Occupied Bandwidth 15.215/15.249 RSS-Gen PASS Young He Field strength of the RSS-210 15.249(a) PASS Young He Fundamental signal Annex B RSS-210 Spurious Emissions 15.209/15.249(a) PASS Young He Annex B RSS-210 Band edge Emissions 15.205/15.249(d) PASS Young He Annex B Antenna requirement 15.203 RSS-Gen PASS Young He Note: The measurement uncertainty is not included in the test result. CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 5 of 27 Report No.: GTI20180934F-2 1.4. Test Facility Address of the report laboratory CTC Laboratories, Inc. Add: 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Laboratory accreditation The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L5365 CTC Laboratories, Inc. has been assessed and proved to be in compliance with CNAS-CL01 Accreditation Criteria for Testing and Calibration Laboratories(identical to ISO/IEC17025: 2005 General Requirements) for the Competence of Testing and Calibration Laboratories. A2LA-Lab Cert. No.: CN1208 CTC Laboratories, Inc. EMC Laboratory has been accredited by A2LA for technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. IC Registration No.: 9783A The 3m alternate test site of CTC Laboratories, Inc. EMC Laboratory has been registered by Certification and Engineer Bureau of Industry Canada for the performance of with Registration NO.: CN0029 on Dec, 2018. FCC-Registration No.: 951311 CTC Laboratories, Inc. EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration 951311, Aug 26, 2017 CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 6 of 27 Report No.: GTI20180934F-2 1.5. Measurement Uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. to TR-100028-01” Electromagnetic compatibility and Radio spectrum Matters (ERM);Uncertainties in the measurement of mobile radio equipment characteristics; Part 1” and TR-100028-02 “Electromagnetic compatibility and Radio spectrum Matters (ERM);Uncertainties in the measurement of mobile radio equipment characteristics; Part 2 “ and is documented in the Shenzhen General Testing & Inspection Technology Co., Ltd. quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. Below is the best measurement capability for Shenzhen General Testing & Inspection Technology Co., Ltd. Test Items Measurement Uncertainty Notes Transmitter power conducted 0.42 dB (1) Transmitter power Radiated 2.14 dB (1) Conducted spurious emissions 9kHz~40GHz 1.60 dB (1) Radiated spurious emissions 9kHz~40GHz 2.20 dB (1) Conducted Emissions 9kHz~30MHz 3.20 dB (1) Radiated Emissions 30~1000MHz 4.70 dB (1) Radiated Emissions 1~18GHz 5.00 dB (1) Radiated Emissions 18~40GHz 5.54 dB (1) Occupied Bandwidth --------- (1) Note (1): This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=1.96. 1.6. Environmental conditions During the measurement the environmental conditions were within the listed ranges: Temperature: 15~35°C Relative Humidity: 30~60 % Air Pressure: 101kPa CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 7 of 27 Report No.: GTI20180934F-2 2. GENERAL INFORMATION 2.1. Client Information Applicant: Wahoo Fitness LLC Address: 90 W. Wieuca Road #110 Atlanta Georgia 30342 United States Manufacturer: East West Industries Vietnam LLC Address: NO.27, Street No.2, VSIP 2, Hoa Phu Ward, Thu Dau Mot City, Binh Duong Province, Vietnam 84, Viet Nam 2.2. General Description of EUT Product Name: SMART TRAINER Model/Type reference: WF120 Adding Model(s): / Model difference: / Power supply: Input: AC 100-240V 50-60Hz 2.5A Max Output: DC 48V 3A Hardware version: V1.0 Software version: V1.0 ANT+: Supported type: ANT+ Modulation: GFSK Operation frequency: 2457MHz Antenna type: Ceramic Antenna Antenna gain: 5.46dBi CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 8 of 27 Report No.: GTI20180934F-2 3. Description of Test Modes Peripherals Devices: OUTSIDE SUPPORT EQUIPMENT No. Equipment Model Serial No. Manufacture Trade name Remark N.A N.A N.A Note: All the above equipment /cable were placed in worse case position to maximize emission signals during emission test. Operation Frequency The Applicant provides communication tools software to control the EUT for staying in continuous transmitting (Duty Cycle more than 98%) mode for testing. ANT+ Channel Frequency (MHz) 00 2457 TEST MODE: For RF test items The engineering test program was provided and enabled to make EUT continuous transmit. For AC power line conducted emissions: The EUT was set to connect with large package sizes transmission. CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 9 of 27 Report No.: GTI20180934F-2 4. Measurement Instruments List Tonscend JS0806-2 Test system Calibrated Item Test Equipment Manufacturer Model No. Serial No. Calibrated until Date Spectrum Rohde & 1 FSU26 100105 Jan. 07, 2017 Dec. 28 2019 Analyzer Schwarz Spectrum Rohde & 2 FUV40-N 101331 Jan. 07, 2017 Dec. 28 2019 Analyzer Schwarz MXG Vector 3 Signal Agilent N5182A MY47420864 Jan. 07, 2017 Dec. 28 2019 Generator Signal 4 Agilent E8257D MY46521908 Jan. 07, 2017 Dec. 28 2019 Generator 5 Power Sensor Agilent U2021XA MY5365004 Jan. 07, 2017 Dec. 28 2019 6 Power Sensor Agilent U2021XA MY5365006 Jan. 07, 2017 Dec. 28 2019 Simultaneous 7 Agilent U2531A TW54493510 Jan. 07, 2017 Dec. 28 2019 Sampling DAQ Climate 8 TABAI PR-4G A8708055 Jan. 07, 2017 Dec. 28 2019 Chamber Wideband Radio Rohde & 9 Communication CMW500 116410 Jan. 06, 2018 Dec. 28 2019 Schwarz Tester Climate 10 ESPEC MT3065 / Jan. 04,2018 Dec. 28 2019 Chamber 300328 v2.1.1 11 TONSCEND v2.6 / / / test system Item Test Equipment Manufacturer Model No. Serial No. Calibrated until 1 EMI Test Receiver Rohde & Schwarz ESCI 100658 Dec. 28 2019 2 High pass filter micro-tranics HPM50111 142 Dec. 28 2019 3 Log-Bicon Antenna Schwarzbeck CBL6141A 4180 Dec. 28 2019 Ultra-Broadband 4 ShwarzBeck BBHA9170 25841 Dec. 28 2019 Antenna 5 Loop Antenna LAPLAC RF300 9138 Dec. 28 2019 6 Spectrum Analyzer Rohde & Schwarz FSU26 100105 Dec. 28 2019 7 Horn Antenna Schwarzbeck BBHA 9120D 647 Dec. 28 2019 8 Pre-Amplifier HP 8447D 1937A03050 Dec. 28 2019 9 Pre-Amplifier EMCI EMC051835 980075 Dec. 28 2019 10 Antenna Mast UC UC3000 N/A N/A 11 Turn Table UC UC3000 N/A N/A 12 Cable Below 1GHz Schwarzbeck AK9515E 33155 Dec. 28 2019 13 Cable Above 1GHz Hubersuhner SUCOFLEX102 DA1580 Dec. 28 2019 14 Splitter Mini-Circuit ZAPD-4 400059 Dec. 28 2019 RF Connection 15 HUBER+SUHNER RE-7-FL N/A Dec. 28 2019 Cable CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 10 of 27 Report No.: GTI20180934F-2 RF Connection Chengdu 16 --- --- Dec. 28 2019 Cable E-Microwave Compliance 17 High pass filter BSU-6 34202 Dec. 28 2019 Direction systems Chengdu EMCAXX-10R 18 Attenuator --- Dec. 28 2019 E-Microwave NZ-3 High and low 19 ESPEC MT3065 12114019 Dec. 28 2019 temperature box Note:1. The Cal. Interval was one year. 2. The cable loss has calculated in test result which connection between each test instruments. CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 11 of 27 Report No.: GTI20180934F-2 5. TEST ITEM AND RESULTS 5.1. AC Power Line Conducted Emissions Limit Conducted Emission Test Limit Maximum RF Line Voltage (dBV) Frequency Quasi-peak Level Average Level 150kHz~500kHz 66 ~ 56 * 56 ~ 46 * 500kHz~5MHz 56 46 5MHz~30MHz 60 50 Notes: (1) *Decreasing linearly with logarithm of the frequency. (2) The lower limit shall apply at the transition frequencies. (3) The limit decrease in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. Test Configuration Test Procedure 1. The EUT was setup according to ANSI C63.10:2013 requirements. 2. The EUT was placed on a platform of nominal size, 1 m by 1.5 m, raised 80 cm above the conducting ground plane. The vertical conducting plane was located 40 cm to the rear of the EUT. All other surfaces of EUT were at least 80 cm from any other grounded conducting surface. 3. The EUT and simulators are connected to the main power through a line impedances stabilization network (LISN). The LISN provides a 50ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN. (Please refer to the block diagram of the test setup and photographs) 4. Each current-carrying conductor of the EUT power cord, except the ground (safety) conductor, was individually connected through a LISN to the input power source. 5. The excess length of the power cord between the EUT and the LISN receptacle were folded back and forth at the center of the lead to form a bundle not exceeding 40 cm in length. 6. Conducted Emissions were investigated over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9 kHz. 7. During the above scans, the emissions were maximized by cable manipulation. CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 12 of 27 Report No.: GTI20180934F-2 Test Mode: Please refer to the clause 3 Test Results Test Voltage: AC 120V/60 Hz Terminal: Line Emission Level= Read Level+ Correct Factor CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 13 of 27 Report No.: GTI20180934F-2 Test Voltage: AC 120V/60 Hz Terminal: Neutral Emission Level= Read Level+ Correct Factor CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 14 of 27 Report No.: GTI20180934F-2 5.2. 20 dB Occupied Bandwidth Limit Operation frequency range 2400MHz~2483.5MHz. TEST CONFIGURATION TEST PROCEDURE 1. The transmitter output was connected to the spectrum analyzer through an attenuator, the path loss was compensated to the results for each measurement. 2. Set to the maximum power setting and enable the EUT transmit continuously 3. Use the following spectrum analyzer settings: Span = approximately 2 to 3 times the 20 dB bandwidth, centered on a hopping channel RBW ≥ 1% of the 20 dB bandwidth, VBW ≥ RBW Sweep = auto, Detector function = peak, Trace = max hold 4. Measure and record the results in the test report. TEST MODE: Please refer to the clause 3 TEST RESULTS 99% 20dB Bandwidth Type Channel Bandwidth Result (MHz) (MHz) GFSK 00 1.1114 0.9768 Pass CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 15 of 27 Report No.: GTI20180934F-2 20dB Bandwidth Date: 17.OCT.2018 11:29:51 99% Bandwidth Date: 17.OCT.2018 11:31:45 CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 16 of 27 Report No.: GTI20180934F-2 5.3. Radiated field strength of the fundamental signal LIMIT Field strength of fundamental Field strength of harmonics Fundamental frequency (millivolts/meter) (microvolts/meter) 902-928 MHz 50 (94dBuV/m @3m) 500 (54dBuV/m @3m) 2400-2483.5 MHz 50 (94dBuV/m @3m) 500 (54dBuV/m @3m) 5725-5875 MHz 50 (94dBuV/m @3m) 500 (54dBuV/m @3m) 24.0-24.25 GHz 250 (108dBuV/m @3m) 2500 (68dBuV/m @3m) Frequencies above 1000 MHz, the field strength limits are based on average limits TEST CONFIGURATION TEST PROCEDURE 1. The EUT was setup and tested according to ANSI C63.10:2013 requirements. 2. The EUT is placed on a turn table which is 1.5 meter above ground. The turn table is rotated 360 degrees to determine the position of the maximum emission level. 3. The EUT waspositioned such that the distance from antenna to the EUT was 3 meters. 4. The antenna is scanned from 1 meter to 4 meters to find out the maximum emission level. Thisis repeated for both horizontal and vertical polarization of the antenna. In order to find the maximum emission, all of the interface cables were manipulated according to ANSI C63.10:2013 on radiated measurement. 5. The receiver set as follow: RBW=1MHz, VBW=3MHz Peak detector for Peak value. RBW=1MHz, VBW=3MHz RMS detector for Average value. TEST MODE: Please refer to the clause 3 CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 17 of 27 Report No.: GTI20180934F-2 TEST RESULTS Read Correction Limit Margin Frequency Test Level Factor Level (dBuV/m) Line Polarization (MHz) (dB) value (dBuV) (dB/m) (dBuV/m) 2457 64.21 -5.63 58.58 114 -55.42 Vertical Peak 2457 65.32 -5.63 59.69 114 -54.31 Horizontal Peak Remark: 1. Emission level (dBuV/m) =Raw Value (dBuV)+Correction Factor (dB/m) 2. Correction Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 3. Margin value = Limit value- Emission level. 4. -- Mean the PK detector measured value is below average limit. 5. The other emission levels were very low against the limit. CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 18 of 27 Report No.: GTI20180934F-2 5.4. Radiated Spurious Emissions and Bandedge Emission LIMIT FCC CFR Title 47 Part 15 Subpart C Section 15.209/ RSS-210 Annex B Frequency Limit (dBuV/m @3m) Value 30MHz~88MHz 40.00 Quasi-peak 88MHz~216MHz 43.50 Quasi-peak 216MHz~960MHz 46.00 Quasi-peak 960MHz~1GHz 54.00 Quasi-peak 54.00 Average Above 1GHz 74.00 Peak TEST CONFIGURATION  9 kHz ~ 30 MHz  30 MHz ~ 1 GHz  Above 1 GHz CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 19 of 27 Report No.: GTI20180934F-2 TEST PROCEDURE 1. The EUT was setup and tested according to ANSI C63.10:2013 requirements. 2. The EUT is placed on a turn table which is 0.8 meter above ground for below 1 GHz, and 1.5 m for above 1 GHz. The turn table is rotated 360 degrees to determine the position of the maximum emission level. 3. The EUT was set 3 meters from the receiving antenna, which was mounted on the top of a variable height antenna tower. 4. For each suspected emission, the EUT was arranged to its worst case and then tune the Antenna tower (from 1 m to 4 m) and turntable (from 0 degree to 360 degrees) to find the maximum reading. A pre-amp and a high pass filter are used for the test in order to get better signal level to comply with the guidelines. 5. Set to the maximum power setting and enable the EUT transmit continuously. 6. Use the following spectrum analyzer settings (1) Span shall wide enough to fully capture the emission being measured; (2) Below 1 GHz: RBW=120 kHz, VBW=300 kHz, Sweep=auto, Detector function=peak, Trace=max hold; If the emission level of the EUT measured by the peak detector is 3 dB lower than the applicable limit, the peak emission level will be reported. Otherwise, the emission measurement will be repeated using the quasi-peak detector and reported. (3) From 1 GHz to 10th harmonic: RBW=1MHz, VBW=3MHz Peak detector for Peak value. RBW=1MHz, VBW=3MHz RMS detector for Average value. TEST MODE: Please refer to the clause 3 TEST RESULTS CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 20 of 27 Report No.: GTI20180934F-2 Radiated Spurious Emissions  9 kHz ~ 30 MHz The EUT was pre-scanned the frequency band (9 kHz ~ 30 MHz), found the radiated level lower than the limit, so don’t show on the report.  30 MHz ~ 1 GHz Polarization: Vertical CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 21 of 27 Report No.: GTI20180934F-2 Polarization: Horizontal Remark: 1. Emission level (dBuV/m) =Raw Value (dBuV)+Correction Factor (dB/m) 2. Correction Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 3. Margin value = Limit value- Emission level. 4. -- Mean the PK detector measured value is below average limit. 5. The other emission levels were very low against the limit. CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 22 of 27 Report No.: GTI20180934F-2  Above 1 GHz Read Correction Limit Margin Frequency Test Level Factor Level (dBuV/m) Line Polarization (MHz) (dB) value (dBuV) (dB/m) (dBuV/m) 4914 45.23 -4.29 40.94 74 -33.06 Vertical Peak 7371 44.78 1.05 45.83 74 -28.17 Vertical Peak 4914 43.26 -4.29 38.97 74 -35.03 Horizontal Peak 7371 40.39 1.05 41.44 74 -32.56 Horizontal Peak Remark: 1. Emission level (dBuV/m) =Raw Value (dBuV)+Correction Factor (dB/m) 2. Correction Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 3. Margin value = Limit value- Emission level. 4. -- Mean the PK detector measured value is below average limit. 5. The other emission levels were very low against the limit. CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 23 of 27 Report No.: GTI20180934F-2 Bandedge Emission Ant. Pol. Horizontal Test Mode: 2457MHz CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 24 of 27 Report No.: GTI20180934F-2 Ant. Pol. Vertical Test Mode: 2457MHz Remark: 1. Emission level (dBuV/m) =Raw Value (dBuV)+Correction Factor (dB/m) 2. Correction Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 3. Margin value = Limit value- Emission level. 4. -- Mean the PK detector measured value is below average limit. 5. The other emission levels were very low against the limit. CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 25 of 27 Report No.: GTI20180934F-2 5.5. Antenna requirement Requirement FCC CFR Title 47 Part 15 Subpart C Section 15.203: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of anantenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. FCC CFR Title 47 Part 15 Subpart C Section 15.247(c) (1)(i): (i) Systems operating in the 2400~2483.5 MHz band that is used exclusively for fixed. Point-to-point operations may employ transmitting antennas with directional gain greater than 6dBi provided the maximum conducted output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6dBi. Test Result The EUT's antenna is soldered to the PCB using a ceramic antenna. The gain of the antenna is 5.46 dBi. asdass ada Please reference to the annex: Internal Photographs CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 26 of 27 Report No.: GTI20180934F-2 6. EUT TEST PHOTOS Please reference to the annex: Test Photo CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn

Page 27 of 27 Report No.: GTI20180934F-2 7. PHOTOGRAPHS OF EUT CONSTRUCTIONAL Please reference to the annex: Extra EUT Photo and Internal EUT Photo **********************THE END********************** CTC Laboratories, Inc 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : yz.cnca.cn


Document Created: 2019-09-06 15:51:57
Document Modified: 2019-09-06 15:51:57
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC