Antenna Specifications

FCC ID: PADWF110

Cover Letter(s)

Download: PDF
FCCID_2663660

mm DATA SHEET XxEFRABRUOAIRAH 5220 Chip antenna For Bluetooth / WLAN Applications 5.20 + 0.10 2.12 + 0.10 1.05 + 0.10

1. Electrical Specification Part Number WAN5S220D245M04 Central Frequency 2450 MHz Bandwidth 100 (Min.) MHz Return Loss —10 (Max) dB Peak Gain 1.57 dBi Impedance 50 Ohm Operating Temperature —40~+85 °C Maximum Power 4 W Resistance to Soldering Heats 10 ( @ 260°C ) sec. Polarization Linear Azimuth Beamwidth Omni—directional Termination Ni / Sn (Leadless) Remark : Bandwidth & Peak Gain was measured under evaluation board of page2 e Part Number Information WAN 5220 D 245 M 04 A B C D E F A Product Series Antenna B Dimension L x W 5.2X2.0mm (+—0.2mm) C Material High K material D Working Frequency 2.4 ~ 2.5GHz E Feeding mode Monopole & Single Feeding F Antenna type Type 04 . XERIKESHEIRAt) WinWave Electronic Co., Ltd | ." "l in "l AVE 952 No.82, Sec. 3, Beisin Rd, Sindian District, New Taipei City 23143, Taiwan(R.0.C.) (TEL]+886 2 8911—0266 [Fax])+886 2 8911—0883 RoHS lead—free compliant

2. Recommended PCB Pattern e Evaluation Board Dimension £ * * —A Unit : mm Feed Line TOP Copper VIA e Suggested Matching Circuit 1.,0nH Feeding 4414 I— EFREHEOHEIRKA~t) WinWave Electronic Co., Ltd & "l i A "l AVE 952 No.82, Sec. 3, Beisin Rd, Sindian District, New Taipei City 23143, Taiwan(R.0.C.) (TEL]+886 2 8911—0266 (Fax])+886 2 8911—0883 ROHS lead—free compliant

e Layout Dimensions in Clearance area( Size=7.0*5.0mm) 50 ohm Matching Circuit FootPrint (Unit : mm) 3 2.4 4.2 > 1 XERIKESHEIRAt) WinWave Electronic Co., Ltd T w in "l AVE 9F—2 No082, Sec. 3, Beisin Rd, Sindian District, New Taipei City 23143, Taiwan(R.0.C.) &L & (TEL}+886 2 8911—0266 (Fax])+886 2 8911—0883 RoHS lead—free compliant

3. Measurement Results + Return Loss FI@ 522 Log Mag 10.00dE,/ Ref 0.000dE [F1] 50.00 »1 2.400000000 4Hz —10.859 dB 2 2.450000000 4Hz —19.104 dB 40 .00 3 2,500000000 @Hz —11.30% dB 30,00 20 .00 10.00 0000 K Cc —10,00 —20,00 —30,00 =40 .00 —50 .00 <a~ [2 Start 1 GHz IFBW 70 kHz Stop 3 GHz m( XERIKESHEIRAt) WinWave Electronic Co., Ltd N "l in "l AVE 952 No.82, Sec. 3, Beisin Rd, Sindian District, New Taipei City 23143, Taiwan(R.0.C.) l @ (TEL]+886 2 8911—0266 [Fax])+886 2 8911—0883 RoH lead—free compliant

e Radiation Pattern Power (dBm) L 10 A2 80 Unit : mm Efficiency Peak Gain Directivity 2400MHz 55.56 % 0.57 dBi 4.13 dBi 2450MHz 70.58 % 1.79 dBi 4.03 dBi 2500MHz 57.13 % 1.26 dBi 4.11 dBi Chamber Coordinate System SGH y DUT C_| z7 _é X Turning Support <—— XERIKESHEIRAt) WinWave Electronic Co., Ltd C "l i A "l AVE 952 No.82, Sec. 3, Beisin Rd, Sindian District, New Taipei City 23143, Taiwan(R.0.C.) &L (TEL]+886 2 8911—0266 [Fax])+886 2 8911—0883 RoHS lead—free compliant

4. Reliability and Test Condictions ITEM REQUIREMENTS TEST CONDITION Solderability 1. Wetting shall exceed 90% coverage ¥ Pre—heating 2. No visible mechanical damage temperature:150°C /&0sec. TEMP / :230+5%C Solder temperature:230+5 4+1 sec. ¥ Duration:4+1sec. Pm ¥ Solder:Sn—Ag3.0—Cu0.5 150° ¥ Flux for lead free: rosin "6Us" Solder heat 1. No visible mechanical damage ¥ Pre—heating Resistance 2. Central Freq. change :within + 6% temperature:150°C /&0sec. TEMP (C) ¥ Solder temperature:260+5°C $ 1005 sec. ¥ Duration:10+0.5sec. ¥ Solder:Sn—Ag3.0—Cu0.5 1509T ¥ Flux for lead free: rosin Cosec Component 1. No visible mechanical damage The device should be reflow Adhesion soldered(230+5°C. for 10sec.) to (Push test) a tinned copper substrate A dynometer force gauge should be applied the side of the component. The device must with—ST—F 0.5 Kg without failure of the termination attached to component. Component 1. No visible mechanical damage ¥ Insert 10cm wire into the Adhesion remaining open eye (Pull test) bend ,the ends of even wire lengths upward and wind together. ¥ Terminal shall not be remarkably damaged. XERIKESHEIRAt) WinWave Electronic Co., Ltd "l i A "l AVE 952 No.82, Sec. 3, Beisin Rd, Sindian District, New Taipei City 23143, Taiwan(R.0.C.) (TEL]+886 2 8911—0266 [Fax])+886 2 8911—0883 4 RdHS lead—free compliant

Thermal 1. No visible mechanical damage ¥ 4+85°C=>30+3min shock 2. Central Freq. change :within +6% —40°C =>30+3min Phase Temperature(°C ) Time(min) _ Test cycle:10 cycles 1 +85+5°C 30+3 ¥ The chip shall be stabilized 2 Room Temperature Within 3sec at normal condition for 3 —40+2°C 30+3 2~3 hours before measuring. 4 Room Temperature Within 3sec Resistance 1. No visible mechanical damage ¥ Temperature: 85+5°C to High 2. Central Freq. change :within +6% ¥ Duration: 1000+12hrs Temperature 3. No disconnection or short circuit. ¥ The chip shall be stabilized at normal condition for 2~3 hours before measuring. Resistance 1. No visible mechanical damage ¥ Temperature:—40+5°C to Low 2. Central Freq. change :within +6% ¥ Duration: 1000+12hrs Temperature 3. No disconnection or short circuit. ¥ The chip shall be stabilized at normal condition for 2~3 hours before measuring. Humidity 1. No visible mechanical damage ¥ Temperature: 40+2°C 2. Central Freq. change :within +6% ¥ Humidity: 90% to 95% RH 3. No disconnection or short circuit. ¥ Duration: 1000+12hrs ¥ The chip shall be stabilized at normal condition for 2~3 hours before measuring. XERIKESHEIRAt) WinWave Electronic Co., Ltd &\ w i n w nve 9F—2, No.82, Sec. 3, Beisin Rd., Sindian District, New Taipei City 23143, Taiwan([R.O0.C.] (TEL]+886 2 8911—0266 [Fax])+886 2 8911—0883 RdHS lead—free compliant

5. Soldering and Mounting Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. The terminations are suitable for all wave and re—flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. Iron S oldering Retiow Soxering PaDEESTING 20001 No amas, reg.uesnes sc.o5nne natusey Ed cne s wmin s COoung 105 max : 5o [Earae nn www rannsnens 5 o [so t [Bto o & E 1zo > 3 1s0 mm ;: [180_ ______ & & s= E Eo~120 s 30605 E Over 605 Gradual coolin E 1 TMEiSec) TM Ejec) Recommended temperature profiles for re—flow soldering in Figure 1. Products attachment with a soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. + Preheat circuit and products to 150°C + Never contact the ceramic with the iron tip + Use a 20 watt soldering iron with tip diameter of 1.0mm + 280°C tip temperature (max) + 1.0mm tip diameter (max) +« Limit soldering time to 3 sec. XERIKESHEIRAt) WinWave Electronic Co., Ltd T "l in "l AVE 952 No.82, Sec. 3, Beisin Rd, Sindian District, New Taipei City 23143, Taiwan(R.0.C.) &\ @ (TEL}+886 2 8911—0266 (Fax)+886 2 8911—0883 RoHS lead—free compliant

6. Packaging Information + Tape Specification: 4,00 +0 .10 2.00 +. OS 4 .00 +0. 10 ® 1.50 +.10 [1,75 +0 . 10 —£ 1 12.00 +.30 5.50 +.05 ® 1.50 +0.25 .229 +0.02 + RBDMAX 1 \—/‘\7“MAX —»| ==|— T —»| |L&— 2.28 #+0. 10 1 .58 +0. 10 5.70 +0. 10 PA iC Cc + Reel Specification: (7", 180 mm) Tape Width(mm) A(mm) B(mm) C({(mm) D{(mm) |Chip/Reel(pcs) 12 12+1.0 60+2 |13.5+0.5| 178+2 2000 s XERIKESHEIRAt) WinWave Electronic Co., Ltd T "l in "l AVE 952 No.82, Sec. 3, Beisin Rd, Sindian District, New Taipei City 23143, Taiwan(R.0.C.) & (TEL}+886 2 8911—0266 (Fax)+886 2 8911—0883 RoHS lead—free compliant

7. Storage and Transportation Information + Storage Conditions To maintain the solderability of terminal electrodes: 1. Temperature and humidity conditions: —10~ 40°C and 30~70% RH. 2. Recommended products should be used within 6 months from the time of delivery. 3. The packaging material should be kept where no chlorine or sulfur exists in the air. + Transportation Conditions 1. Products should be handled with care to avoid damage or contamination from perspiration and skin oils. 2. The use of tweezers or vacuum pick up is strongly recommended for individual components. 3. Bulk handling should ensure that abrasion and mechanical shock are minimized. XERIKESHEIRAt) WinWave Electronic Co., Ltd T "l in "l AVE 952 No.82, Sec. 3, Beisin Rd, Sindian District, New Taipei City 23143, Taiwan(R.0.C.) & @ (TEL}+886 2 8911—0266 (Fax)+886 2 8911—0883 RoHS lead—free compliant

8. Revision Table Revision Date Content Remark V1 9°" Dec, 2013 New issued XERIKESHEIRAt) WinWave Electronic Co., Ltd Bfi\ @ w I n w nve 9F—2, No.82, Sec. 3, Beisin Rd., Sindian District, New Taipei City 23143, Taiwan([R.O0.C.) (TEL])+886 2 8911—0266 (Fax])+886 2 8911—0883 RdHS lead—free compliant


Document Created: 2013-12-10 10:17:47
Document Modified: 2013-12-10 10:17:47
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC