Test Report WLAN Conducted Part 3

FCC ID: P5IC1K01

Test Report

Download: PDF
FCCID_1081513

5.5 POWER SPECTRAL DENSITY MEASUREMENT 5.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT The Maximum of Power Spectral Density Measurement is 8dBm. 5.5.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until R&S SPECTRUM ANALYZER FSP40 100037 Aug. 15, 2007 NOTE: 1.The measurement uncertainty is less than +/- 2.6dB, which is calculated as per the NAMAS document NIS81. 2.The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. Report No.: RF951124L01 110 Report Format Version 2.0.5

5.5.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer through an attenuator, the bandwidth of the fundamental frequency was measured with the spectrum analyzer using 3 kHz RBW and 30 kHz VBW, set sweep time = span/3 kHz. The power spectral density was measured and recorded. The sweep time is allowed to be longer than span/3 kHz for a full response of the mixer in the spectrum analyzer. 5.5.4 DEVIATION FROM TEST STANDARD No deviation 5.5.5 TEST SETUP EUT SPECTRUM ANALYZER 5.5.6 EUT OPERATING CONDITION Same as Item 4.3.6 Report No.: RF951124L01 111 Report Format Version 2.0.5

5.5.7 TEST RESULTS - ANTENNA A 802.11a OFDM modulation MODULATION BPSK TRANSFER RATE 6Mbps TYPE INPUT POWER ENVIRONMENTAL 27deg. C, 53%RH, 120Vac, 60 Hz (SYSTEM) CONDITIONS 965hPa TESTED BY Sky Liao CHANNEL RF POWER LEVEL MAXIMUM CHANNEL FREQUENCY IN 3 kHz BW LIMIT PASS/FAIL (MHz ) (dBm) (dBm) 1 5745 -5.62 8 PASS 3 5785 -5.88 8 PASS 5 5825 -5.42 8 PASS CH1 Report No.: RF951124L01 112 Report Format Version 2.0.5

CH3 CH5 Report No.: RF951124L01 113 Report Format Version 2.0.5

802.11a Turbo OFDM modulation MODULATION BPSK TRANSFER RATE 12Mbps TYPE INPUT POWER ENVIRONMENTAL 27deg. C, 53%RH, 120Vac, 60 Hz (SYSTEM) CONDITIONS 965hPa TESTED BY Sky Liao CHANNEL RF POWER LEVEL MAXIMUM CHANNEL FREQUENCY IN 3 kHz BW LIMIT PASS/FAIL (MHz ) (dBm) (dBm) 1 5760 -9.22 8 PASS 2 5800 -9.04 8 PASS Report No.: RF951124L01 114 Report Format Version 2.0.5

CH1 CH2 Report No.: RF951124L01 115 Report Format Version 2.0.5

5.5.8 TEST RESULTS - ANTENNA C 802.11a OFDM modulation MODULATION BPSK TRANSFER RATE 6Mbps TYPE INPUT POWER ENVIRONMENTAL 27deg. C, 53%RH, 120Vac, 60 Hz (SYSTEM) CONDITIONS 965hPa TESTED BY Sky Liao CHANNEL RF POWER LEVEL MAXIMUM CHANNEL FREQUENCY IN 3 kHz BW LIMIT PASS/FAIL (MHz ) (dBm) (dBm) 1 5745 -6.73 8 PASS 3 5785 -5.88 8 PASS 5 5825 -5.42 8 PASS CH1 Report No.: RF951124L01 116 Report Format Version 2.0.5

CH3 CH5 Report No.: RF951124L01 117 Report Format Version 2.0.5

802.11a Turbo OFDM modulation MODULATION BPSK TRANSFER RATE 12Mbps TYPE INPUT POWER ENVIRONMENTAL 27deg. C, 53%RH, 120Vac, 60 Hz (SYSTEM) CONDITIONS 965hPa TESTED BY Sky Liao CHANNEL RF POWER LEVEL MAXIMUM CHANNEL FREQUENCY IN 3 kHz BW LIMIT PASS/FAIL (MHz ) (dBm) (dBm) 1 5760 -9.22 8 PASS 2 5800 -9.04 8 PASS Report No.: RF951124L01 118 Report Format Version 2.0.5

CH1 CH2 Report No.: RF951124L01 119 Report Format Version 2.0.5

5.6 BAND EDGES MEASUREMENT 5.6.1 LIMITS OF BAND EDGES MEASUREMENT Below –20dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth). 5.6.2 TEST INSTRUMENTS Description & Manufacturer Model No. Serial No. Calibrated Until R&S SPECTRUM ANALYZER FSP40 100037 Aug. 15, 2007 NOTE: 1.The measurement uncertainty is less than +/- 2.6dB, which is calculated as per the NAMAS document NIS81. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. 2.The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. Report No.: RF951124L01 120 Report Format Version 2.0.5

5.6.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz with suitable frequency span including 100 MHz bandwidth from band edge. The band edges was measured and recorded. 5.6.4 DEVIATION FROM TEST STANDARD No deviation 5.6.5 EUT OPERATING CONDITION Same as Item 4.3.6 Report No.: RF951124L01 121 Report Format Version 2.0.5

5.6.6 TEST RESULTS -ANTENNA A The spectrum plots are attached on the following pages. D2 line indicates the highest level, D1 line indicates the 20dB offset below D2. It shows compliance with the requirement in part 15.247(d). Report No.: RF951124L01 122 Report Format Version 2.0.5

802.11a OFDM modulation Report No.: RF951124L01 123 Report Format Version 2.0.5

CH 1 CH 5 Report No.: RF951124L01 124 Report Format Version 2.0.5

802.11a Turbo OFDM modulation Report No.: RF951124L01 125 Report Format Version 2.0.5

Turbo CH 1 Turbo CH 2 Report No.: RF951124L01 126 Report Format Version 2.0.5

5.6.7 TEST RESULTS -ANTENNA C The spectrum plots are attached on the following pages. D2 line indicates the highest level, D1 line indicates the 20dB offset below D2. It shows compliance with the requirement in part 15.247(d). Report No.: RF951124L01 127 Report Format Version 2.0.5

802.11a OFDM modulation Report No.: RF951124L01 128 Report Format Version 2.0.5

CH 1 CH 5 Report No.: RF951124L01 129 Report Format Version 2.0.5

802.11a Turbo OFDM modulation Report No.: RF951124L01 130 Report Format Version 2.0.5

Turbo CH 1 Turbo CH 2 Report No.: RF951124L01 131 Report Format Version 2.0.5

5.7 ANTENNA REQUIREMENT 5.7.1 STANDARD APPLICABLE For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247(a), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 5.7.2 ANTENNA CONNECTED CONSTRUCTION The antennas used in this product are as following: Cable Net Gain Antenna No. Brand Name Model No. Gain (dBi) Connector Loss (dB) (dB) Type Wistron A DBA-SSMA-01 2.06 0.9 1.16 dipole RSMA Neweb Corp. B CUSHCRUFT SRSM5150MRA 2 0.9 1.1 dipole RSMA HUBER+ C SPA 5500/40/14/O/V_C 13.5 0.9 12.6 panel SMA SUHNER Report No.: RF951124L01 132 Report Format Version 2.0.5

6. INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025. USA FCC, UL, A2LA Germany TUV Rheinland Japan VCCI Norway NEMKO Canada INDUSTRY CANADA , CSA R.O.C. CNLA, BSMI, NCC Netherlands Telefication Singapore PSB , GOST-ASIA(MOU) Russia CERTIS(MOU) Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26052943 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3185050 Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also Report No.: RF951124L01 133 Report Format Version 2.0.5

APPENDIX-A MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No any modifications are made to the EUT by the lab during the test. Report No.: RF951124L01 A-1 Report Format Version 2.0.5


Document Created: 2007-02-14 12:37:16
Document Modified: 2007-02-14 12:37:16
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC