Modular Request Letter

FCC ID: OWS-MIL51

Cover Letter(s)

Download: PDF
FCCID_3244864

  Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Company name: Silver Spring Networks FCC ID: OWS-MIL51 Gentlemen,     In   accordance   with   47CFR   15.212   Modular   Transmitters   and   KDB   996369   D01   ‘Module   Certification   Guide   v01r04’.   FCC   ID:   OWS-­MIL51   has   been   examined   against   the   following   requirements.   Requirement  per  15.212  and  KDB  996369  D01     Explanation  from  Grantee     ‘Modular  Certification  Guide  v01r04   (do  not  write  yes/no,  but  explain  why  product   complies/how  it  is  achieved)   The  radio  elements  must  have  the  radio  frequency  circuitry   shielded.  Physical  components  and  tuning  capacitor(s)  may  be   A  stainless  steel  shield  completely  covers   the  module  including  radio  elements.   located  external  to  the  shield,  but  must  be  on  the  module   assembly   The  module  must  have  buffered  modulation/data  inputs  to  ensure   The  Milli  5  does  not  have  any  external   that  the  device  will  comply  with  Part  15  requirements  with  any   modulation  inputs.     type  of  input  signal   Power  supply  regulation  must  be  supplied   The  module  must  contain  power  supply  regulation  on  the  module   by  host  device  and  must  follow  guidelines   specified  in  User  Manual.   The  module  must  contain  a  permanently  attached  antenna,  or   The  module  does  not  contain  a  permanently   contain  a  unique  antenna  connector,  and  be  marketed  and   attached  antenna,  nor  a  unique  antenna   operated  only  with  specific  antenna(s),  per  Sections  15.203,   connector.    50  ohm  PCB  Design  guidelines   15.204(b),  15.204(c),  15.212(a),  2.929(b)   are  provided  within  the  User  Manual.   The  module  was  tested  on  HDK  (Hardware   Development  Kit,  SSN  PN  174-­0768-­00)   that  provides  circuitry  representative  of  a   The  module  must  demonstrate  compliance  in  a  stand-­alone   typical  host  system.    HDK  includes   configuration   regulated  power,  buffered  data  inputs,  a  50   ohm  co-­planar  waveguide  and  external   antenna  connector.   The  module  must  be  labelled  with  its  permanently  affixed  FCC  ID   FCC  ID  label  is  present  on  the  module.   label,  or  use  an  electronic  display  (See  KDB  Publication  784748   about  labelling  requirements)   The  module  complies  with  all  the   The  module  must  comply  with  all  specific  rules  applicable  to  the   requirements  of  §15.212(a)(1)  modular  rules   transmitter  including  all  the  conditions  provided  in  the  integration   only  when  constrained  to  specific  operating   instructions  by  the  grantee   host(s)  as  specified  in  the  User  Manual.   Please  refer  to  the  MPE  test  report.    Max   The  module  must  comply  with  RF  exposure  requirements   gain  antenna  allowed  on  this  device  is  3  dBi.   Silver Spring Networks, Inc. • 230 West Tasman Drive • San Jose, California 95134 • T +1 669 770 4000 • ssni.com

  Name:  Asim  Tirmizi         Date:  December  16,  2016     Title:   Manager  HWQA             Signature  of  applicant   Silver Spring Networks, Inc. • 230 West Tasman Drive • San Jose, California 95134 • T +1 669 770 4000 • ssni.com


Document Created: 0640-07-10 00:00:00
Document Modified: 0640-07-10 00:00:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC