Test Report

FCC ID: OUK-VSLZ9931

Test Report

Download: PDF
FCCID_84775

Partial reproduction of this document is prohibited without prior written consent of Acme Testing Inc. ACME TESTING INC., 2002 VALLEY HWY, P.O. BOX 3, ACME, WASHINGTON 98220-0003 888-226-3837. REPORT OF MEASUREMENTS PART 15C (15.249) - INTENTIONAL RADIATOR DEVICE: TRANSMITTER FOR 3D POSITION SENSOR MODEL: TXM-900-HP-II MANUFACTURER: PHOENIX TECHNOLOGIES INC. ADDRESS: 550 – 655 WEST KENT AVENUE NORTH VANCOUVER BRITISH COLUMBIA CANADA V6P 6T7 THE DATA CONTAINED IN THIS REPORT WAS COLLECTED ON 2 NOVEMBER 1999 AND COMPILED BY: PAUL G. SLAVENS LEONARD G. BELISLE CHIEF EMC ENGINEER EMC TECHNICIAN WORK ORDER: 2012 DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 1 OF 13

1. GENERAL....................................................................................................................................................................... 3 1.1 PURPOSE .................................................................................................................................................................... 3 1.2 MANUFACTURER ....................................................................................................................................................... 3 1.3 TEST LOCATION ......................................................................................................................................................... 3 1.4 TEST PERSONNEL....................................................................................................................................................... 3 2. TEST RESULTS SUMMARY....................................................................................................................................... 4 3. DESCRIPTION OF EQUIPMENT AND PERIPHERALS ........................................................................................ 5 3.1 EQUIPMENT UNDER TEST (EUT) ............................................................................................................................... 5 3.2 MODE OF OPERATION DURING TESTS ........................................................................................................................ 5 3.3 MODIFICATIONS REQUIRED FOR COMPLIANCE ........................................................................................................... 5 3.4 EUT PERIPHERALS .................................................................................................................................................... 5 3.5 DESCRIPTION OF INTERFACE CABLES......................................................................................................................... 6 4. ANTENNA REQUIREMENT ....................................................................................................................................... 7 4.1 REGULATION.............................................................................................................................................................. 7 4.2 RESULT ...................................................................................................................................................................... 7 5. CONDUCTED EMISSIONS TESTS ............................................................................................................................ 8 5.1 TEST EQUIPMENT....................................................................................................................................................... 8 5.2 PURPOSE .................................................................................................................................................................... 8 5.3 TEST PROCEDURES .................................................................................................................................................... 8 5.4 TEST RESULTS ........................................................................................................................................................... 9 6. RADIATED EMISSIONS ............................................................................................................................................ 10 6.1 REGULATION............................................................................................................................................................ 10 6.2 TEST EQUIPMENT..................................................................................................................................................... 11 6.3 TEST PROCEDURES .................................................................................................................................................. 12 6.4 TEST RESULTS ......................................................................................................................................................... 12 7. MISCELLANEOUS COMMENTS AND NOTES..................................................................................................... 13 DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 2 OF 13

1. General 1.1 Purpose The purpose of this report is to show compliance to the FCC regulations for unlicensed devices operating under section 15.249 of the Code of Federal Regulations title 47. 1.2 Manufacturer Company Name: Phoenix Technologies Inc. Contact: Chris Cheung Street Address: 550 – 655 West Kent Avenue North City/Province: Vancouver British Columbia Country/Postal Code: Canada V6P 6T7 Telephone: 604 321-3238 Fax: 604 321-3286 1.3 Test location Company: Acme Testing Inc. Street Address: 2002 Valley Highway Mailing Address: PO Box 3 City/State/Zip: Acme WA 98220-0003 Laboratory: Test Site 2 Telephone: 888 226-3837 Fax: 360 595-2722 E-mail: acmetest@acmetesting.com Web: www.acmetesting.com Receipt of EUT: 2 November 1999 1.4 Test Personnel Paul G. Slavens Leonard G. Belisle DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 3 OF 13

2. Test Results Summary Summary of Test Results Transmitter for 3D Position Sensor, model TXM-900-HP-II Requirement CFR Section Test Result Antenna Requirement 15.203 PASS Conducted Emissions < 48.0 dBuV 15.207 PASS Field Strength Limits 15.249 PASS The signed original of this report, supplied to the client, represents the only “official” copy. Retention of any additional copies (electronic or non-electronic media) is at Acme Testing’s discretion to meet internal requirements only. The client has made the determination that EUT Condition, Characterization, and Mode of Operation are representative of production units, and meet the requirements of the specifications referenced herein. Consistent with Industry practice, measurement and test equipment not directly involved in obtaining measurement results but having an impact on measurements (such as cable loss, antenna factors, etc.) are factored into the “Correction Factor” documented in certain test results. Instrumentation employed for testing meets tolerances consistent with known Industry Standards and Regulations. The measurements contained in this report were made in accordance with the referenced standards and all applicable Public Notices received prior to the date of testing. Acme Testing assumes responsibility only for the accuracy and completeness of this data as it pertains to the sample tested. ____________________________ Paul G. Slavens Date of Issuance Chief EMC Engineer DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 4 OF 13

3. Description of Equipment and Peripherals 3.1 Equipment Under Test (EUT) Device: Transmitter for 3D Position Sensor Model Number: TXM-900-HP-II Serial Number: None FCC ID*: OUK-VSLZ9931 Power: 120 V/ 60 Hz Grounding: Local Antenna Distance: 3 meters 3.2 Mode of Operation During Tests The EUT was exercised in its normal mode of operation. 3.3 Modifications Required for Compliance 1. None. 3.4 EUT Peripherals Device Manufacturer Model Number FCC ID Serial Number Power Supply for Visualeyez GlobTek, Inc. TR9CM3000N00-A None 261708 Target Control Module Phoenix Technologies Inc. #3 None TCM99090811 Power Supply for TCM Importé par: MCI M500R None None Personal Computer for TCM USTR Bootleg None None Monitor ViewSonic VCDTS21366 GSS17019 JP72701267 Keyboard Fugitsu FKB4725 C9SKB4725 L8051746 Mouse Logitech M-S38 DZL211107 LZA82356141 DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 5 OF 13

3.5 Description of Interface Cables EUT/Power Supply (GlobTek) Shielded Unshielded Flat Round Length Ferrite Yes No No Yes 2m No EUT/Target Control Module Shielded Unshielded Flat Round Length Ferrite Yes No No Yes 3m No EUT/Personal Computer Shielded Unshielded Flat Round Length Ferrite Yes No No Yes 3m Yes (PC End) Personal Computer/Monitor Shielded Unshielded Flat Round Length Ferrite Yes No No Yes 1m Yes Personal Computer/Keyboard Shielded Unshielded Flat Round Length Ferrite Yes No No Yes 1m Yes Personal Computer/Mouse Shielded Unshielded Flat Round Length Ferrite Yes No No Yes 1.5 m No ARRANGEMENT OF INTERFACE CABLES: All interface cables were positioned for worst case maximum emissions within the manner assumed to be a typical operation condition (please reference photographs). DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 6 OF 13

4. Antenna requirement 4.1 Regulation 15.203 An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of Part 15C. The manufacturer may design the unit so that the user can replace a broken antenna, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with Section 15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this Part are not exceeded. 4.2 Result The intentional radiator uses a wire soldered directly to the PCB. DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 7 OF 13

5. Conducted Emissions Tests Test Requirement: FCC CFR47, Part 15C Test Procedure: ANSI C63.4:1992 5.1 Test Equipment Spectrum Analyzer: Hewlett-Packard 8566B, Serial Number 2410A-00168, Calibrated: 12 March 1999, Calibration due Date: 12 March 2000 RF Preselector: Hewlett-Packard 85685, Serial Number 2648A-00519, Calibrated: 12 March 1999, Calibration due Date: 12 March 2000 Quasi Peak Adapter: Hewlett-Packard 85650A, Serial Number 2043A-00327, Calibrated: 17 March 1999, Calibration due Date: 17 March 2000 Line Impedance Stabilization Network: Rhode & Schwarz ESH2-Z5, Serial Number ACMERS1, Calibrated: 1 September 1999, Calibration due Date: 1 September 2000 5.2 Purpose The purpose of this test is to evaluate the level of conducted noise the EUT imposes on the AC mains. 5.3 Test Procedures For tabletop equipment, the EUT is placed on a 1 meter by 1.5 meters wide and 0.8 meter high nonconductive table that is placed above the groundplane. Floor standing equipment is placed directly on the groundplane. Any supplemental grounding mechanisms are connected, if appropriate. The EUT is connected to its associated peripherals, with any excess I/O cabling bundled to approximately 1 meter. The EUT is connected to a dedicated LISN and all peripherals are connected to a second separate LISN circuit. The LISNs are bonded to the groundplane. Preview tests are performed to determine the “worst case” mode of operation. With the EUT operating in “worst case” mode, final conducted measurements are taken. Conducted measurements are made on each current carrying conductor with respect to ground. Conducted Emissions Test Characteristics Frequency range 0.45 MHz - 30.0 MHz Test instrumentation resolution bandwidth 9 kHz Lines Tested Line 1/Line 2 DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 8 OF 13

5.4 Test Results A summary of the highest amplitude emissions is listed below. For detailed plots of all emissions from 0.15 MHz - 30 MHz, please refer to the accompanying data in the list of attachments. LINE 1 PEAK # FREQ. (MHz) AMPL (dBuV) 1 2.207 35.0 2 4.877 34.7 3 7.451 40.9 4 8.775 38.6 5 14.04 37.9 6 21.54 34.7 LINE 2 PEAK # FREQ. (MHz) AMPL (dBuV) 1 1.415 34.6 2 1.745 35.3 3 1.89 34.6 4 4.857 35.2 5 7.451 39.5 6 8.344 38.5 7 13.29 40.3 DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 9 OF 13

6. Radiated Emissions 6.1 Regulation (a) The field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following: Fundamental Field Strength Field Strength Frequency of Fundamental of Harmonics (millivolts/meter) (microvolts/meter) 902 - 928 MHz 50 500 2400 - 2483.5 MHz 50 500 5725 - 5875 MHz 50 500 24.0 - 24.25 GHz 250 2500 (b) Field strength limits are specified at a distance of 3 meters. (c) Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209, whichever is the lesser attenuation. (d) As shown in Section 15.35(b), for frequencies above 1000 MHz, the above field strength limits are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 10 OF 13

6.2 Test Equipment Spectrum Analyzer: Hewlett-Packard 8566B, Serial Number 2410A-00168, Calibrated: 12 March 1999, Calibration due Date: 12 March 2000 RF Preselector: Hewlett-Packard 85685, Serial Number 2648A-00519, Calibrated: 12 March 1999, Calibration due Date: 12 March 2000 Quasi Peak Adapter: Hewlett-Packard 85650A, Serial Number 2043A-00327, Calibrated: 17 March 1999, Calibration due Date: 17 March 2000 Line Impedance Stabilization Network: Rhode & Schwarz ESH2-Z5, Serial Number ACMERS1, Calibrated: 1 September 1999, Calibration due Date: 1 September 2000 Broadband Biconical Antenna (20 MHz to 200 MHz): EMCO 3110, Serial Number 1115, Calibrated: 28 September 1999, Calibration due Date: 28 September 2000 Broadband Log Periodic Antenna (200 MHz to 1000 MHz): EMCO 3146, Serial Number 2853, Calibrated: 10 October 1999, Calibration due Date: 10 October 2000 EUT Turntable Position Controller: EMCO 1061-3M, Serial Number 9003-1441, No Calibration Required Antenna Mast: EMCO 1051, Serial Number 9002-1457, No Calibration Required 2 GHz to 10 GHz Low Noise Preamplifier: Milliwave 593-2898, Serial Number 2494, Calibrated: 22 January 1999, Calibration due Date: 22 January 2000 Double Ridge Guide Horn Antenna: EMCO 3115, Serial Number 9807-5534, Calibrated: 28 December 1998, Calibration due Date: 28 December 1999 DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 11 OF 13

6.3 Test Procedures For tabletop equipment, the EUT is placed on a 1 meter by 1.5 meters wide and 0.8 meter high nonconductive table that sits on a flush mounted metal turntable. Floor standing equipment is placed directly on the flush mounted metal turntable. The EUT is connected to its associated peripherals with any excess I/O cabling bundled to approximately 1 meter. Preview tests are performed to determine the “worst case” mode of operation. With the EUT operating in “worst case” mode, emissions from the unit are maximized by adjusting the polarization and height of the receive antenna and rotating the EUT on the turntable. Manipulating the system cables also maximizes EUT emissions. Radiated Emissions Test Characteristics Frequency range 30 MHz – 10,000 MHz Test distance 3m Test instrumentation resolution bandwidth 120 kHz (30 MHz – 1,000 MHz) 1 MHz (1,000 MHz – 10,000 MHz) Receive antenna scan height 1m-4m Receive antenna polarization Vertical/Horizontal 6.4 Test Results PRODUCT EMISSIONS AVERAGE DATA EMISSION SPEC MEASUREMENTS SITE No FREQUENCY LIMIT ABS dLIM MODE POL HGT AZM MHz dBuV/m dB cm deg 1 1806.53 54.0 43.2 -10.8 AVG H 127 95 2 2710.00 54.0 33.7 -20.3 AVG H 100 87 PEAK DATA* EMISSION SPEC MEASUREMENTS SITE No FREQUENCY LIMIT ABS dLIM MODE POL HGT AZM MHz dBuV/m dB cm deg 1 903.278 94.0 73.7 -20.4 PK H 100 71 2 1806.60 54.0 49.5 -4.5 PK H 127 95 3 2709.5 54.0 43.1 -10.9 PK H 100 87 * To show 15.35 compliance for average measurements over 1,000 MHz. DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 12 OF 13

7. Miscellaneous Comments and Notes 1. None. DATE OF ISSUANCE: 18 NOVEMBER 1999 REPORT NUMBER: 990286 FCC ID: OUK-VSLZ9931 PAGE 13 OF 13


Document Created: 2001-04-12 09:11:17
Document Modified: 2001-04-12 09:11:17
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC