Test report for JBP

FCC ID: OP5PL5561

Test Report

Download: PDF
FCCID_1688532

SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw FCC EMC TEST REPORT Applicant’s company Eleven Engineering Inc. Applicant Address 10150-100 Street, Suite 900, Edmonton, Alberta, Canada T5J OP6 Manufacturer’s company Eleven Engineering Inc. Manufacturer Address 10150-100 Street, Suite 900, Edmonton, Alberta, Canada T5J OP6 Product Name SKAA USB TX Brand Name SKAA Model Name PL5561 Test Standard 47 CFR FCC Part 15 Subpart B Classification of ITE Class B Received Date Mar. 01, 2012 Final Test Date Mar. 12, 2012 Submission Type Original Equipment Statement The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.4-2009 and 47 CFR FCC Part 15 Subpart B. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Report Format Version: 01

Report No.: FD0D2902-01 Table of Contents 1. CERTIFICATE OF COMPLIANCE ......................................................................................................................... 1 2. SUMMARY OF THE TEST RESULT .......................................................................................................................... 2 3. GENERAL INFORMATION .................................................................................................................................. 3 3.1. Product Details....................................................................................................................................................................................3 3.2. Accessories.........................................................................................................................................................................................3 3.3. Table for Filed Antenna.......................................................................................................................................................................4 3.4. Table for Carrier Frequenciess............................................................................................................................................................5 3.5. Table for Test Modes ...........................................................................................................................................................................5 3.6. Table for Testing Locations..................................................................................................................................................................5 3.7. Table for Supporting Units ...................................................................................................................................................................5 3.8. EUT Operation during Test ...................................................................................................................................................................6 3.9. Test Configurations .............................................................................................................................................................................7 4. TEST RESULT ..................................................................................................................................................... 9 4.1. AC Power Line Conducted Emissions Measurement...........................................................................................................................9 4.2. Radiated Emissions Measurement ....................................................................................................................................................13 5. LIST OF MEASURING EQUIPMENTS ................................................................................................................... 18 6. TEST LOCATION.............................................................................................................................................. 20 7. TAF CERTIFICATE OF ACCREDITATION ............................................................................................................. 21 APPENDIX A. PHOTOGRAPHS OF EUT.......................................................................................................... A1 ~ A6 APPENDIX B. TEST PHOTOS.......................................................................................................................... B1 ~ B5 Report Format Version: 01 Page No. : i of ii Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 History of This Test Report REPORT NO. VERSION DESCRIPTION ISSUED DATE FD0D2902-01 Rev. 01 Initial issue of report Apr. 20, 2012 Receiver Frequency 2412~2462MHz 30~88 40 88~216 43.5 216~960 5th harmonic of highest frequency. 46 Above 960 54 3 Report Format Version: 01 Page No. : ii of ii Issued Date : Apr. 20, 2012

sronvom cam. Report No.: FDOD2202—01 1. CERTIFICATE OF COMPLIANCE Product Name SKAA USB TX Brand Name : SKAA Model Name PL&541 Applicant : Eleven Engineering Inc. Test Standard 47 CFR FCC Part 15 Subpart B Sporton International as requested by the applicant to evaluate the EMI performance of the product sample received on Mar. 01, 2012 would like to declare that the tested sample has been evaluated and found to be in compliance with the tested rule parts. The data recorded as well as the test configuration specified is frue and accurate for showing the sample‘s EMI nature. Jordan Hsiao SPORTON INTERNATIONAL INC. Report Format Version: 01 Page No. : 1 of 21 Isued Date : Apr. 20, 2012

Report No.: FD0D2902-01 2. SUMMARY OF THE TEST RESULT Applied Standard: 47 CFR FCC Part 15 Subpart B Part Rule Section Description of Test Result Under Limit 4.1 15.107 AC Power Line Conducted Emissions Complies 17.55 dB 4.2 15.109 Radiated Emissions Complies 8.38 dB Test Items Uncertainty Remark AC Power Line Conducted Emissions ±2.3dB Confidence levels of 95% Radiated Emissions ±1.9dB Confidence levels of 95% Report Format Version: 01 Page No. : 2 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 3. GENERAL INFORMATION 3.1. Product Details Items Description Power Type From Host System Modulation FHSS (FSK) Frequency Range 2400 ~ 2483.5MHz Channel Number 49 Channel Spacing 1.536 MHz Channel Band Width (99%) 2228.65 kHz Output Power 14.17 dBm Carrier Frequencies Please refer to section 3.4 Antenna Please refer to section 3.3 Remark: A channel palette of 49 channels, which are spaced by 1.536 MHz starting at 2403.585 MHz. From this palette, 20 channels are used by the system at any given moment. Upon startup the system beings to hop on 20 random channels. The hopping sequence is a pseudo random ordered list of the 20 channels, and is 20 elements long. 20 hopping channels are always used at any given point in time. The system has a regular hopping rate of ranging from 100 hops per second to 1000 hops per second, and has a dwell time ranging between 1 ms to 10 ms. During normal operation all channels are used equally and transmissions never span more than 1 hop time. Every hop cycle contains a single transmission from the transmitter and receiver and no channels in the current list of 20 are skipped. This guarantees that all 20 channels are used equally on average, and that the total dwell time on any channel within the hop set is less than 0.4 s in any 8 s period. 3.2. Accessories N/A Report Format Version: 01 Page No. : 3 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 3.3. Table for Filed Antenna Ant. Brand Model Name Antenna Type Connector Gain (dBi) 1 - - PCB Antenna NA 2.01 Report Format Version: 01 Page No. : 4 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 3.4. Table for Carrier Frequenciess Frequency Band Channel No. Frequency 1 2403.585 MHz 2 2405.121 MHz 3 2406.657 MHz : : 23 2483.913 MHz 2400~2483.5MHz 24 2440.449 MHz 25 2441.985 MHz : : 47 2474.241 MHz 48 2475.777 MHz 49 2477.313 MHz 3.5. Table for Test Modes Investigation has been done on all the possible configurations for searching the worst cases. The following table is a list of the test modes shown in this test report. Test Items Mode Antenna AC Power Line Conducted Emissions Normal Use - Radiated Emissions Normal Use - 3.6. Table for Testing Locations Test Site No. Site Category Location FCC Reg. No. IC File No. VCCI Reg. No 03CH0-CB SAC Hsin Chu 262045 IC 4086D - CO01-CB Conduction Hsin Chu 262045 IC 4086D - Open Area Test Site (OATS); Semi Anechoic Chamber (SAC); Fully Anechoic Chamber (FAC). Please refer section 6 for Test Site Address. 3.7. Table for Supporting Units Support Unit Brand Model FCC ID Notebook DELL D400 QDS-BRCM1005-D Mouse First Price FP-M02 DoC Ear phone SHYARO CHI MIC-04 N/A Speaker - - N/A Speaker fixture - - N/A Speaker fixture power - - N/A Report Format Version: 01 Page No. : 5 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 3.8. EUT Operation during Test An executive program, EMCTEST.EXE and Media player under WIN XP, which generates a complete line of continuously repeating “ H “ pattern was used as the test software. The program was executed as follows: a. Turn on the power of all equipment. b. The NB sends “ H“ messages to the panel, and the panel displays “ H “ patterns on the screen. At the same time, the following programs were executed: Executed "Media player" to play audio and video. Repeat the steps from b. Report Format Version: 01 Page No. : 6 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 3.9. Test Configurations 3.9.1. Radiation Emissions Test Configuration AC Main 1 1 EUT DC RS232 VGA LPT RJ-45 RJ-11 USB x 2 Adapter Notebook AUDIO 2 3 Ear phone Mouse Speaker Speaker 4 fixture fixture power Item Connection Shield Length 1 Power cable No 2.6M 2 USB cable Yes 1.8M 3 Ear phone cable No 0.72 M 4 Speaker fixture power 0.11 M No cable Report Format Version: 01 Page No. : 7 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 3.9.2. AC Power Line Conduction Emissions Test Configuration AC Main 1 1 EUT DC RS232 VGA LPT RJ-45 RJ-11 USB x 2 Adapter Notebook AUDIO 2 3 Ear phone Mouse Speaker Speaker 4 fixture fixture power Item Connection Shield Length 1 Power cable No 2.6M 2 USB cable Yes 1.8M 3 Ear phone cable No 0.72 M 4 Speaker fixture power 0.11 M No cable Report Format Version: 01 Page No. : 8 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 4. TEST RESULT 4.1. AC Power Line Conducted Emissions Measurement 4.1.1. Limit For this product which is designed to be connected to the AC power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed below limits table. Frequency (MHz) QP Limit (dBuV) AV Limit (dBuV) 0.15~0.5 66~56 56~46 0.5~5 56 46 5~30 60 50 4.1.2. Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the receiver. Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 KHz 4.1.3. Test Procedures 1. The EUT or host of EUT has to be placed 0.4 meter far from the conducting wall of the shielding room and at least 80 centimeters from any other grounded conducting surface. 2. Connect EUT or host of EUT to the power mains through a line impedance stabilization network (LISN). 3. All the support units are connected to the other LISNs. The LISN should provide 50uH/50ohms coupling impedance. 4. The frequency range from 150 KHz to 30 MHz was searched. 5. Set the test-receiver system to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. 6. The measurement has to be done between each power line and ground at the power terminal. Report Format Version: 01 Page No. : 9 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 4.1.4. Test Setup Layout LEGEND: (1) Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. (2) I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. (3) EUT connected to one LISN. Unused LISN measuring port connectors shall be terminated in 50 Ω. LISN can be placed on top of, or immediately beneath, reference ground plane. (3.1) All other equipment powered from additional LISN(s). (3.2) Multiple outlet strip can be used for multiple power cords of non-EUT equipment. (3.3) LISN at least 80 cm from nearest part of EUT chassis. (4) Cables of hand-operated devices, such as keyboards, mice, etc., shall be placed as for normal use. (5) Non-EUT components of EUT system being tested. (6) Rear of EUT, including peripherals, shall all be aligned and flush with rear of tabletop. (7) Rear of tabletop shall be 40 cm removed from a vertical conducting plane that is bonded to the ground plane. Report Format Version: 01 Page No. : 10 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 4.1.5. Test Deviation There is no deviation with the original standard. 4.1.6. Results of AC Power Line Conducted Emissions Measurement Temperature 20℃ Humidity 50% Test Engineer Sin Chang Phase Line Configuration Normal Link Report Format Version: 01 Page No. : 11 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 Temperature 20℃ Humidity 50% Test Engineer Sin Chang Phase Neutral Configuration Normal Link Note: Level = Read Level + LISN Factor + Cable Loss. Report Format Version: 01 Page No. : 12 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 4.2. Radiated Emissions Measurement 4.2.1. Limit Measurements shall be made with a quasi-peak measuring receiver in the frequency range 30 MHz to 5th harmonic of highest frequency. The quasi-peak measuring receiver shall be in accordance with clause 2 of CISPR 16-1. Receivers with peak detectors shall be in accordance with clause 3 of CISPR 16-1, and shall have a 6 dB bandwidth in accordance with clause 2 of CISPR 16-1. Frequency of Emission (MHz) Field Strength QP Limit (dBuV/m) at 3m 30~88 40 88~216 43.5 216~960 46 Above 960 54 4.2.2. Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of spectrum analyzer and receiver. Receiver Parameter Setting Attenuation Auto Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP Spectrum Parameter Setting Start Frequency 1000 MHz Stop Frequency 5th harmonic of highest frequency RB / VB 1 MHz / 1MHz for Peak 4.2.3. Test Procedures 1. The EUT was placed on the top of the turntable 0.8 meter above ground. The phase center of the receiving antenna mounted on the top of a height-variable antenna tower was placed 3 meters far away from the turntable. 2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. The height of the broadband receiving antenna was varied between one meter and four meters above ground to find the maximum emissions field strength of both horizontal and vertical polarization. 4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was rotated (from 0 degree to 360 degrees) to find the maximum reading. 5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with specified bandwidth under Maximum Hold Mode. Report Format Version: 01 Page No. : 13 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 4.2.4. Test Setup Layout 3m 4.2.5. Test Deviation There is no deviation with the original standard. Report Format Version: 01 Page No. : 14 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 4.2.6. Results of Radiated Emissions (30MHz~1GHz) Temperature 20℃ Humidity 59% Test Engineer Wen Chao Configurations Normal Link Horizontal Report Format Version: 01 Page No. : 15 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 Vertical Note: The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. Emission level (dBuV/m) = 20 log Emission level (uV/m). Corrected Reading: Antenna Factor + Cable Loss + Read Level - Preamp Factor = Level. Report Format Version: 01 Page No. : 16 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 4.2.7. Results for Radiated Emissions (1GHz~5th harmonic of highest frequency) Temperature 20℃ Humidity 59% Test Engineer Wen Chao Configurations Normal Link Horizontal Vertical Note: The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. Corrected Reading: Antenna Factor + Cable Loss + Read Level - Preamp Factor = Level. Report Format Version: 01 Page No. : 17 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 5. LIST OF MEASURING EQUIPMENTS Calibration Instrument Manufacturer Model No. Serial No. Characteristics Remark Date Conduction EMI Test Receiver R&S ESCS 30 100377 9kHz ~ 2.75GHz Sep. 01, 2011 (CO01-CB) Conduction LISN F.C.C. FCC-LISN-50-16-2 04083 150kHz ~ 100MHz Oct. 28, 2011 (CO01-CB) Conduction V- LISN Schwarzbeck NSLK 8127 8127-478 9K ~ 30MHz Nov. 16, 2011 (CO01-CB) Conduction PULSE LIMITER R&S ESH3-Z2 100430 9K~30MHz Jan. 04, 2012 (CO01-CB) Conduction COND Cable - Cable - 0.15MHz~30MHz Dec. 04, 2011 (CO01-CB) Pre-Amplifier WM TF-130N-R1 923365 26.5GHz ~ 40GHz Nov. 17, 2011 Radiation (03CH01-CB) Radiation RF Cable-high Woken High Cable-3 - 1 GHz - 40 GHz Nov. 17, 2011 (03CH01-CB) Radiation RF Cable-high Woken High Cable-4 - 1 GHz - 40 GHz Nov. 17, 2011 (03CH01-CB) BILOG ANTENNA Schaffner CBL6112D 22021 20MHz ~ 2GHz Oct. 17, 2011 Radiation (03CH01-CB) Horn Antenna EMCO 3115 00075790 750MHz~18GHz Nov. 22, 2011 Radiation (03CH01-CB) Radiation Horn Antenna SCHWARZBEAK BBHA 9170 BBHA9170252 15GHz ~ 40GHz Oct. 08, 2011 (03CH01-CB) Pre-Amplifier Agilent 8447D 2944A10991 0.1MHz ~ 1.3GHz Nov. 17, 2011 Radiation (03CH01-CB) Pre-Amplifier Agilent 8449B 3008A02310 1GHz ~ 26.5GHz Nov. 23, 2011 Radiation (03CH01-CB) Pre-Amplifier WM TF-130N-R1 923365 26.5GHz ~ 40GHz Nov. 17, 2011 Radiation (03CH01-CB) Spectrum analyzer R&S FSP 100304 9kHz ~ 40GHz Nov. 22, 2011 Radiation (03CH01-CB) EMI Test Receiver R&S ESCS 30 100355 9KHz ~ 2.75GHz Mar. 06, 2012 Radiation (03CH01-CB) Radiation Loop Antenna Teseq HLA 6120 24155 9 kHz - 30 MHz Sep. 09, 2011 (03CH01-CB) Radiation Turn Table INN CO CO 2000 N/A 0  360 degree N/A (03CH01-CB) Radiation Antenna Mast INN CO CO2000 N/A 1m-4m N/A (03CH01-CB) Radiation RF Cable-low Woken Low Cable-1 N/A 30 MHz - 1 GHz Nov. 17, 2011 (03CH01-CB) Radiation RF Cable-high Woken High Cable-1 N/A 1 GHz – 26.5 GHz Nov. 17, 2011 (03CH01-CB) Radiation RF Cable-high Woken High Cable-2 N/A 1 GHz – 26.5 GHz Nov. 17, 2011 (03CH01-CB) Report Format Version: 01 Page No. : 18 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 Calibration Instrument Manufacturer Model No. Serial No. Characteristics Remark Date Radiation RF Cable-high Woken High Cable-3 N/A 1 GHz - 40 GHz Nov. 17, 2011 (03CH01-CB) Radiation RF Cable-high Woken High Cable-4 N/A 1 GHz - 40 GHz Nov. 17, 2011 (03CH01-CB) Note: Calibration Interval of instruments listed above is one year. Note: * Calibration Interval of instruments listed above is two year. Report Format Version: 01 Page No. : 19 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 6. TEST LOCATION SHIJR ADD : 6Fl., No. 106, Sec. 1, Shintai 5th Rd., Shijr City, Taipei, Taiwan 221, R.O.C. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 HWA YA ADD : No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. TEL : 886-3-327-3456 FAX : 886-3-318-0055 LINKOU ADD : No. 30-2, Dingfu Tsuen, Linkou Shiang, Taipei, Taiwan 244, R.O.C TEL : 886-2-2601-1640 FAX : 886-2-2601-1695 DUNGHU ADD : No. 3, Lane 238, Kangle St., Neihu Chiu, Taipei, Taiwan 114, R.O.C. TEL : 886-2-2631-4739 FAX : 886-2-2631-9740 JUNGHE ADD : 7Fl., No. 758, Jungjeng Rd., Junghe City, Taipei, Taiwan 235, R.O.C. TEL : 886-2-8227-2020 FAX : 886-2-8227-2626 NEIHU ADD : 4Fl., No. 339, Hsin Hu 2nd Rd., Taipei 114, Taiwan, R.O.C. TEL : 886-2-2794-8886 FAX : 886-2-2794-9777 JHUBEI ADD : No.8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C. TEL : 886-3-656-9065 FAX : 886-3-656-9085 Report Format Version: 01 Page No. : 20 of 21 Issued Date : Apr. 20, 2012

Report No.: FD0D2902-01 7. TAF CERTIFICATE OF ACCREDITATION Report Format Version: 01 Page No. : 21 of 21 Issued Date : Apr. 20, 2012


Document Created: 2019-09-05 14:30:15
Document Modified: 2019-09-05 14:30:15
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC