Test Report 2-2

FCC ID: OKUCAB9H680

Test Report

Download: PDF
FCCID_4390765

Report No.: AGC03329190702FE03 Page 53 of 77 TEST PLOT OF MIDDLE CHANNEL

Report No.: AGC03329190702FE03 Page 54 of 77 TEST PLOT OF HIGH CHANNEL

Report No.: AGC03329190702FE03 Page 55 of 77 13. FREQUENCY SEPARATION 13.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: Wide enough to capture the peaks of two adjacent channels. 2. RBW: Start with the RBW set to approximately 30% of the channel spacing; adjust as necessary to best identify the center of each individual channel. 3. Video (or average) bandwidth (VBW) ≥ RBW. 4. Sweep: Auto. e) Detector function: Peak. f) Trace: Max hold. g) Allow the trace to stabilize. Use the marker-delta function to determine the separation between the peaks of the adjacent channels. 13.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 6.2 13.3. MEASUREMENT EQUIPMENT USED The same as described in section 6.3 13.4. LIMITS AND MEASUREMENT RESULT CHANNEL LIMIT RESULT CHANNEL SEPARATION KHz KHz Pass CH01-CH02 1001 >=25 KHz or 2/3 20 dB BW TEST PLOT FOR FREQUENCY SEPARATION Note: The 8-DPSK modulation is the worst case and recorded in the report.

Report No.: AGC03329190702FE03 Page 56 of 77 14. FCC LINE CONDUCTED EMISSION TEST 14.1. LIMITS OF LINE CONDUCTED EMISSION TEST Maximum RF Line Voltage Frequency Q.P.( dBuV) Average( dBuV) 150kHz~500kHz 66-56 56-46 500kHz~5MHz 56 46 5MHz~30MHz 60 50 Note: 1. The lower limit shall apply at the transition frequency. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50 MHz. 14.2. BLOCK DIAGRAM OF LINE CONDUCTED EMISSION TEST EUT & Support Units

Report No.: AGC03329190702FE03 Page 57 of 77 14.3. PRELIMINARY PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. 2. Support equipment, if needed, was placed as per ANSI C63.10. 3. All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4. All support equipments received AC120V/60Hz power from a LISN, if any. 5. The EUT received DC 5V power from adapter which received AC120V/60Hz power from a LISN. 6. The test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7. Analyzer / Receiver scanned from 150 kHz to 30MHz for emissions in each of the test modes. 8. During the above scans, the emissions were maximized by cable manipulation. 9. The test mode(s) were scanned during the preliminary test. Then, the EUT configuration and cable configuration of the above highest emission level were recorded for reference of final testing. 14.4. FINAL PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. EUT and support equipment was set up on the test bench as per step 2 of the preliminary test. 2. A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions. Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. If EUT emission level was less –2dB to the A.V. limit in Peak mode, then the emission signal was re-checked using Q.P and Average detector. 3. The test data of the worst case condition(s) was reported on the Summary Data page.

Report No.: AGC03329190702FE03 Page 58 of 77 14.5. TEST RESULT OF LINE CONDUCTED EMISSION TEST Line Conducted Emission Test Line 1-L

Report No.: AGC03329190702FE03 Page 59 of 77 Line Conducted Emission Test Line 2-N RESULT: PASS Note: All the test modes had been tested, the mode 1 was the worst case. Only the data of the worst case would be record in this test report.

Report No.: AGC03329190702FE03 Page 60 of 77 APPENDIX A: PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION TEST SETUP BELOW 1GHZ RADIATED EMISSION TEST SETUP ABOVE 1GHZ

Report No.: AGC03329190702FE03 Page 61 of 77 CONDUCTED EMISSION TEST SETUP

Report No.: AGC03329190702FE03 Page 62 of 77 APPENDIX B: PHOTOGRAPHS OF EUT Test model: TT1145 TOP VIEW OF EUT BOTTOM VIEW OF EUT

Report No.: AGC03329190702FE03 Page 63 of 77 FRONT VIEW OF EUT BACK VIEW OF EUT

Report No.: AGC03329190702FE03 Page 64 of 77 LEFT VIEW OF EUT RIGHT VIEW OF EUT

Report No.: AGC03329190702FE03 Page 65 of 77 VIEW OF EUT(PORT) OPEN VIEW OF EUT-1

Report No.: AGC03329190702FE03 Page 66 of 77 OPEN VIEW OF EUT-2 VIEW OF BATTERY

Report No.: AGC03329190702FE03 Page 67 of 77 INTERNAL VIEW OF EUT-1 INTERNAL VIEW OF EUT-2

Report No.: AGC03329190702FE03 Page 68 of 77 INTERNAL VIEW OF EUT-3 Antenna INTERNAL VIEW OF EUT-4

Report No.: AGC03329190702FE03 Page 69 of 77 INTERNAL VIEW OF EUT-5 INTERNAL VIEW OF EUT-6

Report No.: AGC03329190702FE03 Page 70 of 77 Series model: CAB-9H680 ALL VIEW OF EUT TOP VIEW OF EUT

Report No.: AGC03329190702FE03 Page 71 of 77 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

Report No.: AGC03329190702FE03 Page 72 of 77 BACK VIEW OF EUT LEFT VIEW OF EUT

Report No.: AGC03329190702FE03 Page 73 of 77 RIGHT VIEW OF EUT VIEW OF EUT(PORT)

Report No.: AGC03329190702FE03 Page 74 of 77 OPEN VIEW OF EUT VIEW OF BATTERY

Report No.: AGC03329190702FE03 Page 75 of 77 INTERNAL VIEW OF EUT-1 INTERNAL VIEW OF EUT-2

Report No.: AGC03329190702FE03 Page 76 of 77 INTERNAL VIEW OF EUT-3 Antenna INTERNAL VIEW OF EUT-4

Report No.: AGC03329190702FE03 Page 77 of 77 INTERNAL VIEW OF EUT-5 INTERNAL VIEW OF EUT-6 ----END OF REPORT----


Document Created: 2019-08-07 15:47:56
Document Modified: 2019-08-07 15:47:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC