User manual

FCC ID: OKP1936A

Users Manual

Download: PDF
FCCID_130356

ITEM NO.1936 1) ON / OFF SWITCH — i 2) ON / OFF SWITCH — BIKE: HAND CONTROLLER: The Race Masters Bike uses a 3 6 ME sie The On / Off switch on the hand position switch — Automatic Gear OND controller, is a little knob on the Shift / Off / Manual Gear Shift. The O 0 gght f'\land side of the Hand switch is located at the rear of the ontroller (see diagram). Pull bike, between the twin exhausts , down, and look for the small LED (see diagram) and must be switched /‘ & i |'9h:_ at ufl:e c!:)Otlt?le of the unit to to the correct channel before you ) confirm the Controlier is on. can operate. Listen for the ‘beep‘ to confirm the vehicle is on. RACE MASTERS BIKE CONTROL: 1) MANUAL AND AUTOMATIC GEAR SHIFT: Racemasters Bikes can be operated in two modes — Manual Gear Shift and Automatic Gear Shift. In Automatic Gear Shift mode the bike operates the gears by itself. Playing in Manual Gear Shift mode allows you to take full control of all the gear changes! 1.1) AUTOMATIC GEAR SHIFT MODE : To control the Racemaster Bike in Automatic Gear Shift Mode, first select the required channel (see section 1 above).As previously stated, in Automatic Gear Shift the bike operates the gears by itself, shifting to the correct gear when needed and automatically slowing down at comers. This is the easiest mode for learner drivers. The acceleration / deceleration control can be found on the left hand side of the Hand Controller (see diagram). This control has three settings: Neutral, Acceleration and Braking. Pressing the switch upwards will increase the vehicles acceleration, propelling the Bike forwards. Pulling down on the switch will apply the brakes, rapid!?( decelerating bike. The button is spring loaded and will always retum to the neutral position (standstill). In Automatic Gear Shift mode the acceleration / braking functions are digital proportional, and will increase / decrease depending on the pressure applied to the controller. 1.2) MANUAL GEAR SHIFT MODE: To control the Racemaster Bike in Manual Gear Shift Mode, first select the required channel (see section 1 above). As explained above, playing in Manual Gear Shift mode allows you to take full control of all the gear changes. You decide when to speed up and slow down. Remember sometimes you need to slow down to take corners, or you may lose control of your Bike! Gear Shifting in Manual mode operates by shifting through the 3 available gears — up (faster), and down (slower). Click the Acceleration switch upwards once and release, to move into 1st Gear (see diagram) — the bike will now accelerate forward at it‘s slowest speed. Clicking the Acceleration switch upwards once more moves the Bike into 2nd gear, with the Bike speeding up. Finally clicking the acceleration switch up again, shifts it into 3rd gear — top speed! To Gear Shift down (slow down) simply reverse the procedure. Click the Acceleration switch down once and release, to change from 3rd gear to 2nd gear (slowing the Bike down). Repeat the action again to shift gear down from 3rd to 2nd gear, and once more from 2nd to 1st gear. Finally shifting down from 1st gear automatically brakes the Racemasters Bike, bringing it to a standstill. Click down the gears in rapid succession to bring the Bike to a fast stop! Note: the Acceleration button is spring loaded and will always return to the neutral position (standstill). Wl 2) STEERING : The Racemasters Bike Controller is designed to simulate a realistic driving experience. Turning the handlebars left and right controls the vehicle just like a real Bike! Let go of the handlebars and the Bike will automatically center itself, returning to drive in a straight line! When steering in Automatic Gear Shift mode the Racemasters Bike will adjust it‘s own speed and slow down slightly, when turming comers in order to prevent it ffrom keeling T Warning : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. —

ITEM NO.1936 RACE BIKE 3) LIGHTS AND SOUND : Racemasters Bike features realistic brake lights and braking sound. When decelerating / braking the brake lights and braking sound will automatically be activated. Engine Rev. — press button ‘C‘ for realistic Engine Rev. sound and watch as the bike tries to accelerate forward. Headlights — press button ‘D‘ to activate front headlights, now Racemasters Bike can drive safely in the dark. 4) WIRE ANTENNA: For increased performance and greater Radio Control distance of your Racemaster Bike, unwind the antenna cable wound around the back of the controlier. 5) ADJUSTABLE TRACKING SYSTEM: Please note: Occasionally the sensitive steering system on the Racemasters Bike may need adjusting (possibly due to collisions). To realign the tracking system that controls the steering, first remove the front windshield (see diagram) then slightly adjust the screw located in front of the steering column (see diagram). Ensure the front wheel is pointing directly forwards for accurate readjustment. BATTERY & ON / OFF SWITCH DIAGRAM ~~~B /TD BATTERY INSTALLATION 4 ulng 2eomndiiver on lent cover To repuace satremes unscrew IMPORTANT BATTERY INFORMATION nsert correct as shown in diagram semoue achew on sattEny COvER AS SHOWN w *Do not mix old and new batteries. *Do not mix alkaline, standard (Carbon zinc) or rechargeable (nickel—cadmium) batteries. *Rechargeable batteries not recommended. *Batteries should be replaced by adulits because of small parts. Batteries are to be Inserted with correct polarity. Non—rechargeable batteries are not to be recharged. Only batteries of the same or equivalent type as recommended are to be used. Exhausted batteries are to be removed from the toy. The supply terminals are not to be short—circuited. This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1)This device may not cause harmful interference,and (2)This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been test and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radic frequency energy and, if not instailed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio 0i television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of following measures: Manufactured and Distributed by: [_] Reorient or relocate the receiving antenna. © 2000 Wow—Wee inc.4480 Cote—de—Liesse T.M.R. Quebec HA4N 2R1 [] Increase the separation between the equipment and receiver. Ail rights reserved. {] Connect one equipment into an outlet on a circuit different from that to Made in china. which the receiver is needed. Wow—Wee int‘l., Unit 301 C, 92 Granville Rd. T.9.T. East, Kowloon,H.K. [[] Consult the dealer or an experienced radio/TV technician for help. http://www.wowwee.com


Document Created: 2000-08-10 10:47:49
Document Modified: 2000-08-10 10:47:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC