Test Report 2

FCC ID: O9C-SL3055

Test Report

Download: PDF
FCCID_828492

DFS TEST REPORT REPORT NO.: RF940413L11A MODEL NO.: SL-3055 RECEIVED: June 08, 2007 TESTED: July 17 to 18, 2007 ISSUED: July 19, 2007 APPLICANT: 3Com Corporation ADDRESS: 350 Campus Dirve, Marlborough, MA 10752-3064. U.S.A. ISSUED BY: Advance Data Technology Corporation TEST No. 81-1, Lu Liao Keng, 9 Ling, Wu Lung LOCATION: Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan, R.O.C. This test report consists of 19 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF, A2LA or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF940413L11A 1 Report Format Version 2.0.5 Reference No.: 960608H04

Table of Contents 1. LAB DECLARATION ....................................................................................3 2. EUT INFORMATION ....................................................................................4 2.1 OPERATING FREQUENCY BANDS AND MODE OF EUT ..........................4 2.2 EUT SOFTWARE AND FIRMWARE VERSION ...........................................4 2.3 DESCRIPTION OF AVAILABLE ANTENNAS TO THE EUT .........................4 2.4 EUT MAXIMUM AND MINIMUM CONDUCTED POWER ............................5 2.5 EUT MAXIMUM AND MINIMUM E.I.R.P. POWER .......................................5 2.6 STATEMENT OF MAUNFACTURER ...........................................................5 3. NII DFS RULE REQUIREMENTS ................................................................6 3.1 WORKING MODES AND REQUIRED TEST ITEMS....................................6 3.2 TEST LIMITS AND RADAR SIGNAL PARAMETERS...................................7 4. TEST & SUPPORT EQUIPMENT LIST........................................................9 4.1 TEST INSTRUMENTS .................................................................................9 4.2 DESCRIPTION OF SUPPORT UNITS.........................................................9 5. TEST PROCEDURE .................................................................................. 10 5.1 ADT DFS MEASUREMENT SYSTEM:....................................................... 10 5.2 CALIBRATION OF DFS DETECTION THRESHOLD LEVEL: .................... 11 5.3 DEVIATION FROM TEST STANDARD ...................................................... 12 5.4 CONDUCTED TEST SETUP CONFIGURATION ....................................... 12 5.4.1 CLIENT WITHOUT RADAR DETECTION MODE ...................................... 12 6. TEST RESULTS ........................................................................................ 13 6.1 SUMMARY OF TEST RESULT .................................................................. 13 6.2 DETELED TEST RESULTS ....................................................................... 14 6.2.1 TEST MODE: DEVICE OPERATING IN CLIENT WITHOUT RADAR DETECTION MODE. ................................................................................. 14 6.2.1.1 DFS DETECTION THRESHOLD .............................................................. 14 6.2.1.2 CHANNEL CLOSING TRANSMISSION AND CHANNEL MOVE TIME... 15 7. TESTING LABORATORIES INFORMATION.............................................. 18 8. APPENDIX-A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB........................................................ 19 Report No.: RF940413L11A 2 Report Format Version 2.0.5 Reference No.: 960608H04

1. LAB DECLARATION PRODUCT: 11a/b/g Wireless PCI Adapter BRAND NAME: 3Com MODEL NO.: SL-3055 TEST SAMPLE: ENGINEERING SAMPLE TESTED: July 17 to 18, 2007 APPLICANT: 3Com Corporation STANDARDS: FCC Part 15, Subpart E (Section 15.407) FCC 06-96 The above equipment (Model: SL-3055) has been tested by Advance Data Technology Corporation, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: July 19, 2007 ( Midoli Peng, Specialist ) TECHNICAL ACCEPTANCE : , DATE: July 19, 2007 Responsible for RF ( Hank Chung, Deputy Manager ) APPROVED BY : , DATE: July 19, 2007 ( May Chen, Deputy Manager ) Report No.: RF940413L11A 3 Report Format Version 2.0.5 Reference No.: 960608H04

2. EUT INFORMATION 2.1 OPERATING FREQUENCY BANDS AND MODE OF EUT Table 1: Operating frequency bands and mode of EUT. Operating Frequency Range Operational Mode 5250~5350MHz 5470~5725MHz Client without radar detection ü ü 2.2 EUT SOFTWARE AND FIRMWARE VERSION Table 2: The EUT software/firmware version. No. Product Model No. Software/Firmware Version Utility Version: 1.1.0.25 11a/b/g Wireless PCI 1 SL-3055 Driver Version: 5.3.0.45 Adapter Firmwave Version: 1.0.2.8 2.3 DESCRIPTION OF AVAILABLE ANTENNAS TO THE EUT Table 3: Antenna list. Operation Frequency Max. Ant NO. Antenna Type Range Gain(dBi) Dipole 1 3Com 5.15 – 5.85 GHz 2.5 Antenna Dipole 2 WSS003 Dual Band 5.15 – 5.85 GHz 2.02 Antenna Report No.: RF940413L11A 4 Report Format Version 2.0.5 Reference No.: 960608H04

2.4 EUT MAXIMUM AND MINIMUM CONDUCTED POWER Table 4: The measured conducted output power. MAX. Power MIN. Power Ant Frequency Band(MHz) NO. Output Output Output Output Power(dBm) Power(mW) Power(dBm) Power(mW) 1 5250~5350MHz 16.38 43.45102242 9.42 8.749837752 1 5470~5725MHz 13.74 23.65919697 4.57 2.86417797 2.5 EUT MAXIMUM AND MINIMUM E.I.R.P. POWER Table 5: The E.I.R.P output power list. MAX. Power MIN. Power Ant Frequency Band(MHz) NO. Output Output Output Output Power(dBm) Power(mW) Power(dBm) Power(mW) 1 5250~5350MHz 18.88 77.26805851 11.92 15.55965632 1 5470~5725MHz 16.24 42.07266284 7.07 5.093308711 2.6 STATEMENT OF MAUNFACTURER Manufacturer statement confirming that information regarding the parameters of the detected Radar Waveforms is not available to the end user. And the device doesn’t have Ad Hoc mode on DFS frequency band. Report No.: RF940413L11A 5 Report Format Version 2.0.5 Reference No.: 960608H04

3. NII DFS RULE REQUIREMENTS 3.1 WORKING MODES AND REQUIRED TEST ITEMS The manufacturer shall state whether the UUT is capable of operating as a Master and/or a Client. If the UUT is capable of operating in more than one operating mode then each operating mode shall be tested separately. See tables 1 and 2 for the applicability of DFS requirements for each of the operational modes. Table 6: Applicability of DFS requirements prior to use a channel Operational Mode Requirement Client without Client with radar Master radar detection detection Non-Occupancy Period ü Not required ü DFS Detection Threshold ü Not required ü Channel Availability Check Time ü Not required Not required Uniform Spreading ü Not required Not required U-NII Detection Bandwidth ü Not required ü Table 7: Applicability of DFS requirements during normal operation. Operational Mode Requirement Client without Client with radar Master radar detection detection DFS Detection Threshold ü Not required ü Channel Closing Transmission ü ü ü Time Channel Move Time ü ü ü U-NII Detection Bandwidth ü Not required ü Report No.: RF940413L11A 6 Report Format Version 2.0.5 Reference No.: 960608H04

3.2 TEST LIMITS AND RADAR SIGNAL PARAMETERS DETECTION THRESHOLD VALUES Table 8: DFS Detection Thresholds for Master Devices and Client Devices With Radar Detection. Value Maximum Transmit Power (See Notes 1 and 2) ≥ 200 milliwatt -64 dBm < 200 milliwatt -62 dBm Note 1: This is the level at the input of the receiver assuming a 0 dBi receive antenna. Note 2: Throughout these test procedures an additional 1 dB has been added to the amplitude of the test transmission waveforms to account for variations in measurement equipment. This will ensure that the test signal is at or above the detection threshold level to trigger a DFS response. Table 9: DFS Response Requirement Values Parameter Value Non-occupancy period Minimum 30 minutes Channel Availability Check Time 60 seconds Channel Move Time 10 seconds See Note 1. Channel Closing Transmission Time 200 milliseconds + an aggregate of 60 milliseconds over remaining 10 second period. See Notes 1 and 2. U-NII Detection Bandwidth Minimum 80% of the UNII 99% transmission power bandwidth. See Note 3. Note 1: The instant that the Channel Move Time and the Channel Closing Transmission Time begins is as follows: • For the Short Pulse Radar Test Signals this instant is the end of the Burst. • For the Frequency Hopping radar Test Signal, this instant is the end of the last radar Burst generated. • For the Long Pulse Radar Test Signal this instant is the end of the 12 second period defining the Radar Waveform. Note 2: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of the Channel Move Time plus any additional intermittent control signals required to facilitate a Channel move (an aggregate of 60 milliseconds) during the remainder of the 10 second period. The aggregate duration of control signals will not count quiet periods in between transmissions. Note 3: During the U-NII Detection Bandwidth detection test, radar type 1 is used and for each frequency step the minimum percentage of detection is 90 percent. Measurements are performed with no data traffic. Report No.: RF940413L11A 7 Report Format Version 2.0.5 Reference No.: 960608H04

PARAMETERS OF DFS TEST SIGNALS Step intervals of 0.1 microsecond for Pulse Width, 1 microsecond for PRI, 1 MHz for chirp width and 1 for the number of pulses will be utilized for the random determination of specific test waveforms. Table 10: Short Pulse Radar Test Waveforms. Minimum Minimum Pulse Width PRI Number Percentage of Radar Type Number of (µsec) (µsec) of Pulses Successful Trials Detection 1 1 1428 18 60% 30 2 1-5 150-230 23-29 60% 30 3 6-10 200-500 16-18 60% 30 4 11-20 200-500 12-16 60% 30 Aggregate (Radar Types 1-4) 80% 120 Table 11: Long Pulse Radar Test Waveform Minimum Pulse Chirp Number Minimum Radar PRI Number Percentage of Width Width of Pulses Number of Type (µsec) of Bursts Successful (µsec) (MHz) per Burst Trials Detection 5 50-100 5-20 1000-2000 1-3 8-20 80% 30 Table 12: Frequency Hopping Radar Test Waveform Hopping Minimum Pulse Pulses Hopping Minimum Radar PRI Sequence Percentage of Width per Rate Number of Type (µsec) Length Successful (µsec) Hop (kHz) Trials (msec) Detection 6 1 333 9 0.333 300 70% 30 Report No.: RF940413L11A 8 Report Format Version 2.0.5 Reference No.: 960608H04

4. TEST & SUPPORT EQUIPMENT LIST 4.1 TEST INSTRUMENTS Table 1: Test instruments list. CALIBRATED DESCRIPTION & MANUFACTURER MODEL NO. BRAND UNTIL R&S Spectrum analyzer FSP40 R&S Aug. 15, 2007 Signal generator 8645A Agilent May. 26, 2008 Oscilloscope TDS 5104 Tektronix Apr. 16. 2008 4.2 DESCRIPTION OF SUPPORT UNITS Table 2: Support Unit information. No. Product Brand Model No. ID Spec. The maximum AIR-AP1242AG-A- EIRP is 21.5 dBm, 1 802.11a/b/g Access Point Cisco LDK102056 K9 Antenna Gain is 3dBi Note: This device was functioned as a Master device during the DFS test. Table 3: Software/Firmware information. No. Product Model No. Software/Firmware Version 1. 802.11a/b/g Access Point AIR-AP1242AG-A-K9 C1240-K9W7-TAR.123-8.JEA Report No.: RF940413L11A 9 Report Format Version 2.0.5 Reference No.: 960608H04

5. TEST PROCEDURE 5.1 ADT DFS MEASUREMENT SYSTEM: A complete ADT DFS Measurement System consists of two subsystems: (1) the Radar Signal Generating Subsystem and (2) the Traffic Monitoring Subsystem. The control PC is necessary for generating the Radar waveforms in Table 6, 7 and 8. The traffic monitoring subsystem is specified to the type of unit under test (UUT). Conducted setup configuration of ADT DFS Measurement System Radar Signal Generating Control PC Subsystem Spectrum Oscilloscope Analyzer Attenuator C/S Attenuator Attenuator C/S Traffic Monitoring Support Unit Master / Client with DFS function The test transmission will always be from the Master Device to the Client Device. While the Client device is set up to associate with the Master device and play the MPEG file (6 y Magic Hours) from Master device, the designated MPEG test file and instructions are located at: http://ntiacsd.ntia.doc.gov/dfs/. Report No.: RF940413L11A 10 Report Format Version 2.0.5 Reference No.: 960608H04

5.2 CALIBRATION OF DFS DETECTION THRESHOLD LEVEL: The measured channel is 5500MHz. The radar signal was the same as transmitted channels, and injected into the antenna port of AP (master) or Client Device with Radar Detection, measured the channel closing transmission time and channel move time. The Master antenna gain is 3dBi and required detection threshold is -58dBm (= -62 +1+3)dBm. The calibrated conducted detection threshold level is set to -59dBm. The tested level is lower than required level hence it provides margin to the limit. Conducted setup configuration of Calibration of DFS Detection Threshold Level Control PC Spectrum Oscilloscope Radar Signal Generating Analyzer Subsystem 50Ω Load (Terminator) Attenuator C/S 50Ω Load Attenuator Attenuator C/S (Terminator) Report No.: RF940413L11A 11 Report Format Version 2.0.5 Reference No.: 960608H04

5.3 DEVIATION FROM TEST STANDARD No deviation. 5.4 CONDUCTED TEST SETUP CONFIGURATION 5.4.1 CLIENT WITHOUT RADAR DETECTION MODE Control PC Spectrum Oscilloscope Radar Signal Generating Analyzer Subsystem Attenuator C/S C/S Master Attenuator Attenuator Client (UUT) PC Notebook The UUT is a U-NII Device operating in Client mode without radar detection. The radar test signals are injected into the Master Device. Report No.: RF940413L11A 12 Report Format Version 2.0.5 Reference No.: 960608H04

6. TEST RESULTS 6.1 SUMMARY OF TEST RESULT Clause Test Parameter Remarks Pass/Fail 15.407 DFS Detection Threshold Not Applicable NA 15.407 Channel Availability Check Time Not Applicable NA 15.407 Channel Move Time Applicable Pass 15.407 Channel Closing Transmission Time Applicable Pass 15.407 Non- Occupancy Period Not Applicable NA 15.407 Uniform Spreading Not Applicable NA 15.407 U-NII Detection Bandwidth Not Applicable NA Report No.: RF940413L11A 13 Report Format Version 2.0.5 Reference No.: 960608H04

6.2 DETELED TEST RESULTS 6.2.1 TEST MODE: DEVICE OPERATING IN CLIENT WITHOUT RADAR DETECTION MODE. Client with injection at the Master . (The radar test signals are injected into the Master Device. 6.2.1.1 DFS DETECTION THRESHOLD For a detection threshold level of –62dBm and the Master antenna gain is 3dBi. The Required detection threshold is -58dBm (= -62 +1+3)dBm. The conducted radar burst level is set to -59dBm. The tested level is lower than required level hence it provides margin to the limit. Radar signal Noise Floor Radar Signal 1 Report No.: RF940413L11A 14 Report Format Version 2.0.5 Reference No.: 960608H04

6.2.1.2 CHANNEL CLOSING TRANSMISSION AND CHANNEL MOVE TIME WLAN Traffic Traffic Signal Noise Floor NOTE: T1 denotes the start of duty cycle period is 0.056442th second. T2 denotes the end of duty cycle period is 0.220859th second. T2 – T1= 0.164417 seconds. Duty Cycle = 12.152% Report No.: RF940413L11A 15 Report Format Version 2.0.5 Reference No.: 960608H04

Radar signal 1 Radar Signal Traffic Signal Noise Floor NOTE: T1 denotes the start of Channel Move Time upon the end of the last Radar burst. T2 denotes the data transmission time of 200ms from T1. T4 denotes the 10 second from T1 to observe the aggregate duration of transmissions. Radar Signal Traffic Signal Master’s beacon Noise Floor NOTE: An expanded plot for the device vacates the channel in the required 200ms. Report No.: RF940413L11A 16 Report Format Version 2.0.5 Reference No.: 960608H04

Type 1 Radar Statistical Performances Trial # Pulses per Pulse Width (s) PRI (s) Detection Burst 1 18 1.0u 1.428m Yes 2 18 1.0u 1.428m Yes 3 18 1.0u 1.428m Yes 4 18 1.0u 1.428m Yes 5 18 1.0u 1.428m Yes 6 18 1.0u 1.428m Yes 7 18 1.0u 1.428m Yes 8 18 1.0u 1.428m Yes 9 18 1.0u 1.428m Yes 10 18 1.0u 1.428m Yes 11 18 1.0u 1.428m Yes 12 18 1.0u 1.428m Yes 13 18 1.0u 1.428m Yes 14 18 1.0u 1.428m Yes 15 18 1.0u 1.428m Yes 16 18 1.0u 1.428m Yes 17 18 1.0u 1.428m Yes 18 18 1.0u 1.428m Yes 19 18 1.0u 1.428m Yes 20 18 1.0u 1.428m Yes 21 18 1.0u 1.428m Yes 22 18 1.0u 1.428m Yes 23 18 1.0u 1.428m Yes 24 18 1.0u 1.428m Yes 25 18 1.0u 1.428m Yes 26 18 1.0u 1.428m Yes 27 18 1.0u 1.428m Yes 28 18 1.0u 1.428m Yes 29 18 1.0u 1.428m Yes 30 18 1.0u 1.428m Yes Detection Rate: 100 % Report No.: RF940413L11A 17 Report Format Version 2.0.5 Reference No.: 960608H04

7. TESTING LABORATORIES INFORMATION We, ADT Corp., were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025. USA FCC, UL, A2LA Germany TUV Rheinland Japan VCCI Norway NEMKO Canada INDUSTRY CANADA , CSA R.O.C. TAF, BSMI, NCC Netherlands Telefication Singapore PSB , GOST-ASIA(MOU) Russia CERTIS(MOU) Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3185050 Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report No.: RF940413L11A 18 Report Format Version 2.0.5 Reference No.: 960608H04

8. APPENDIX-A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No any modifications are made to the EUT by the lab during the test. Report No.: RF940413L11A 19 Report Format Version 2.0.5 Reference No.: 960608H04


Document Created: 2007-08-13 11:30:02
Document Modified: 2007-08-13 11:30:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC