1503RSU02004-FCC-15B Report

FCC ID: O9C-BJNGAFB0008

Test Report

Download: PDF
FCCID_2640959

MRT Technology (Suzhou) Co., Ltd Report No.: 1503RSU02004 Phone: +86-512-66308358 Report Version: V01 Fax: +86-512-66308368 Issue Date: 06-01-2015 Web: www.mrt-cert.com MEASUREMENT REPORT FCC Part 15B FCC ID: O9C-BJNGAFB0008 APPLICANT: Hewlett Packard Company Application Type: Certification Product: Wireless LAN Access Point Model No.: BJNGA-FB0008, JH306A Brand Name: HP FCC Classification: FCC Class B Digital Device (JBP) FCC Rule Part(s): FCC Part 15 Subpart B Test Procedure(s): ANSI C63.4: 2009 Test Date: Mar.16 ~ May. 29, 2015 Reviewed By : ( Robin Wu ) Approved By : ( Marlin Chen ) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.4-2009. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. FCC ID: O9C-BJNGAFB0008 Page Number: 1 of 31

Report No.: 1503RSU02004 Revision History Report No. Version Description Issue Date 1503RSU02004 Rev. 01 Initial report 06-01-2015 FCC ID: O9C-BJNGAFB0008 Page Number: 2 of 31

Report No.: 1503RSU02004 CONTENTS Description Page §2.1033 General Information ......................................................................................................... 4 1. INTRODUCTION ..................................................................................................................... 5 1.1. Scope ........................................................................................................................... 5 1.2. MRT Test Location ....................................................................................................... 5 2. PRODUCT INFORMATION ..................................................................................................... 6 2.1. Equipment Description.................................................................................................. 6 2.2. Description of Available Antennas ................................................................................ 7 2.3. Device Capabilities ....................................................................................................... 7 2.4. Test Configuration ........................................................................................................ 8 2.5. Test Software ............................................................................................................... 9 2.6. EMI Suppression Device(s)/Modifications ..................................................................... 9 2.7. Labeling Requirements ............................................................................................... 10 3. DESCRIPTION OF TEST .......................................................................................................11 3.1. Evaluation Procedure .................................................................................................. 11 3.2. AC Line Conducted Emissions .................................................................................... 11 3.3. Radiated Emissions .................................................................................................... 12 4. TEST EQUIPMENT CALIBRATION DATE ............................................................................ 13 5. MEASUREMENT UNCERTAINTY ......................................................................................... 14 6. TEST RESULT ...................................................................................................................... 15 6.1. Summary .................................................................................................................... 15 6.2. Conducted Emission Measurement ............................................................................ 16 6.2.1. Test Limit ................................................................................................................ 16 6.2.2. Test Setup............................................................................................................... 16 6.2.3. Test Result of Conducted Emissions ....................................................................... 17 6.3. Radiated Emission Measurement ............................................................................... 21 6.3.1. Test Limit ................................................................................................................ 21 6.3.2. Test Setup............................................................................................................... 21 6.3.3. Test Result of Radiated Emissions .......................................................................... 23 7. CONCLUSION....................................................................................................................... 31 FCC ID: O9C-BJNGAFB0008 Page Number: 3 of 31

Report No.: 1503RSU02004 §2.1033 General Information Applicant: Hewlett Packard Company Applicant Address: 153 Taylor Street Littleton Massachusetts, United States 01460-1407 Manufacturer: Hewlett Packard Company Manufacturer Address: 153 Taylor Street Littleton Massachusetts, United States 01460-1407 Test Site: MRT Technology (Suzhou) Co., Ltd Test Site Address: D8 Building, Youxin Industrial Park, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China MRT FCC Registration No.: 809388 Model No.: BJNGA-FB0008, JH306A FCC ID: O9C-BJNGAFB0008 Test Device Serial No.: N/A Production Pre-Production Engineering FCC Classification: FCC Class B Digital Device (JBP) Test Facility / Accreditations Measurements were performed at MRT Laboratory located in Tian’edang Rd., Suzhou, China.  MRT facility is a FCC registered (MRT Reg. No. 809388) test facility with the site description report on file and has met all the requirements specified in Section 2.948 of the FCC Rules.  MRT facility is an IC registered (MRT Reg. No. 11384A-1) test laboratory with the site description on file at Industry Canada.  MRT facility is a VCCI registered (R-4179, G-814, C-4664, T-2206) test laboratory with the site description on file at VCCI Council.  MRT Lab is accredited to ISO 17025 by the American Association for Laboratory Accreditation (A2LA) under the American Association for Laboratory Accreditation Program (A2LA Cert. No. 3628.01) in EMC, Telecommunications and Radio testing for FCC, Industry Canada, EU and TELEC Rules. FCC ID: O9C-BJNGAFB0008 Page Number: 4 of 31

Report No.: 1503RSU02004 1. INTRODUCTION 1.1. Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2. MRT Test Location The map below shows the location of the MRT LABORATORY, its proximity to the Taihu Lake. These measurement tests were conducted at the MRT Technology (Suzhou) Co., Ltd. Facility located at D8 Building, Youxin Industrial Park, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4-2009 on September 30, 2013. FCC ID: O9C-BJNGAFB0008 Page Number: 5 of 31

Report No.: 1503RSU02004 2. PRODUCT INFORMATION 2.1. Equipment Description Product Name Wireless LAN Access Point Model No. BJNGA-FB0008, JH306A Power Type POE input Frequency Range For 2.4GHz Band: 802.11b/g/n: 2412 ~ 2462 MHz For 5.0GHz Band: 802.11a/n/ac: 5150 ~ 5350MHz 5470 ~ 5725MHz 5725 ~ 5850MHz Type of Modulation 802.11b: DSSS 802.11g/a/n/ac: OFDM FCC ID: O9C-BJNGAFB0008 Page Number: 6 of 31

t NH IA Report No.: 1503RSU02004 2.2. Description of Available Antennas ‘ 2.4 Indoor 2 3.83 383 6.84 fi‘»’ JG696A 10 5 P—T—MP 2 5.69 569 8.70 2.4 Ouldoor 2 6.70 6.70 9m ces JL195A 3—8.1J * 5 P—T—MP o 10.70 —2.0 10.70 137 2.4 Outdoor 2 8.80 s.so 8.80 JL193A 5 P—T—MP 2 8.90 7.0 8.90 8.90 2.4 Outdoor 2 11.50 11.50 11.50 JL194A 5 P—T—P 2 15.60 15.60 15.60 2.3. Device Capabilities This device contains the following capabilities: 2 4GHz&5GHz (DTS/UNI!) FCC ID: O9C—BJNGAFBOOO8 Page Number: 7 of 31

Report No.: 1503RSU02004 2.4. Test Configuration The Wireless LAN Access Point FCC ID: O9C-BJNGAFB0008 was tested per the guidance FCC Part 15 Subpart B: 2014 and ANSI C63.4: 2009 was used to reference the appropriate EUT setup for radiated spurious emissions testing and AC line conducted testing. Connection Diagram (Mode 1: Communication by optical fiber cable) Connection Diagram (Mode 2: Communication by LAN cable) FCC ID: O9C-BJNGAFB0008 Page Number: 8 of 31

Report No.: 1503RSU02004 Signal Cable Type Signal cable Description A LAN cable Non-shielding, 1.0 m B Optical fiber cable Non-shielding, >10m C LAN cable Non-shielding, >10m Product Manufacturer Model No. Serial No. Power Cord 1 Notebook Lenovo X201 3626AM3 Non-Shielded, 1.8m 2 H3C Router H3C WX3010-PoEP N/A N/A PD-9001GR/AT/AC, 3 POE Adapter HP CN44GF60Y7 N/A J9867A RTXM191-400, 4 Optical Module H3C EA131200121282 N/A RTXM191-400-H3C Note 1: When we configured the EUT set-up, the console port didn’t connect some peripherals, which was used to do software upgrade for the professional installers. 2.5. Test Software 1 Setup the EUT and simulators as shown on above. 2 Make the EUT communicate with notebook by optical fiber cable or LAN cable. 2.6. EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. FCC ID: O9C-BJNGAFB0008 Page Number: 9 of 31

Report No.: 1503RSU02004 2.7. Labeling Requirements Per 2.1074 & 15.19; Docket 95-19 The label shall be permanently affixed at a conspicuous location on the device; instruction manual or pamphlet supplied to the user and be readily visible to the purchaser at the time of purchase. However, when the device is so small wherein placement of the label with specified statement is not practical, only the trade name and FCC ID must be displayed on the device per Section 15.19(a)(5). Please see attachment for FCC ID label and label location. FCC ID: O9C-BJNGAFB0008 Page Number: 10 of 31

Report No.: 1503RSU02004 3. DESCRIPTION OF TEST 3.1. Evaluation Procedure The measurement procedures described in the American National Standard for Methods of Measurement of Radio-Noise Emission from Low-Voltage Electrical Equipment in the Range of 9kHz to 40GHz (ANSI C63.4-2009) was used in the measurement of the Wireless LAN Access Point FCC ID: O9C-BJNGAFB0008. Deviation from measurement procedure…………………………….....................................None 3.2. AC Line Conducted Emissions The line-conducted facility is located inside an 8'x4'x4' shielded enclosure. A 1m x 2m wooden table 80cm high is placed 40cm away from the vertical wall and 80cm away from the sidewall of the shielded room. Two 10kHz-30MHz, 50Ω/50uH Line-Impedance Stabilization Networks (LISNs) are bonded to the shielded room floor. Power to the LISNs is filtered by external high-current high-insertion loss power line filters. These filters attenuate ambient signal noise from entering the measurement lines. These filters are also bonded to the shielded enclosure. The EUT is powered from one LISN and the support equipment is powered from the second LISN. If the EUT is a DC-powered device, power will be derived from the source power supply it normally will be powered from and this supply line(s) will be connected to the second LISN. All interconnecting cables more than 1 meter were shortened to a 1 meter length by non-inductive bundling (serpentine fashion) and draped over the back edge of the test table. All cables were at least 40cm above the horizontal reference ground-plane. Power cables for support equipment were routed down to the second LISN while ensuring that that cables were not draped over the second LISN. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The RF output of the LISN was connected to the receiver and exploratory measurements were made to determine the frequencies producing the maximum emission from the EUT. The receiver was scanned from 150 kHz to 30 MHz. The detector function was set to peak mode for exploratory measurements while the bandwidth of the analyzer was set to 9 kHz. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Each emission was also maximized by varying: power lines, the mode of operation or resolution, clock or data exchange speed, scrolling H pattern to the EUT and/or support equipment whichever determined the worst-case emission. Once the worst case emissions have been identified, the one EUT cable configuration/arrangement and mode of operation that produced these emissions are used for final measurements on the same test site. Line conducted emissions test results are shown in Section 6.2. FCC ID: O9C-BJNGAFB0008 Page Number: 11 of 31

Report No.: 1503RSU02004 3.3. Radiated Emissions The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. For measurements above 1GHz absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections. For measurements below 1GHz, the absorbers are removed. An MF Model 210SS turntable is used for radiated measurement. It is a continuously rotatable, remote controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. An 80cm high PVC support structure is placed on top of the turntable. For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive antenna height using a broadband antenna from 30 MHz up to the upper frequency shown in 15.33(b)(1) depending on the highest frequency generated or used in the device or on which the device operates or tunes. For frequencies above 1GHz, linearly polarized double ridge horn antennas were used. For frequencies below 30 MHz, a calibrated loop antenna was used. When exploratory measurements were necessary, they were performed at 1 meter test distance inside the semi-anechoic chamber using broadband antennas, broadband amplifiers, and spectrum analyzers to determine the frequencies and modes producing the maximum emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The test set-up was placed on top of the 0.8 meter high, 1 x 1.5 meter table. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and investigated. The system configuration, mode of operation, if applicable, turntable azimuth, and receive antenna height was noted for each frequency found. Final measurements were made in the semi-anechoic chamber using calibrated, linearly polarized broadband and horn antennas. The test setup was configured to the setup that produced the worst case emissions. The spectrum analyzer was set to investigate all frequencies required for testing to compare the highest radiated disturbances with respect to the specified limits. The turntable containing the EUT was rotated through 360 degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height producing the maximum emission. Each emission was maximized by changing the orientation of the EUT through three orthogonal planes and changing the polarity of the receive antenna, whichever produced the worst-case emissions. According to 3dB beam-width of horn antenna, the horn antenna should be always directed to the EUT when rising height. FCC ID: O9C-BJNGAFB0008 Page Number: 12 of 31

Report No.: 1503RSU02004 4. TEST EQUIPMENT CALIBRATION DATE Conducted Emissions Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date EMI Test Receiver R&S ESR7 MRTSUE06001 1 year 2015/11/07 Two-Line V-Network R&S ENV216 MRTSUE06002 1 year 2015/11/07 Two-Line V-Network R&S ENV216 MRTSUE06003 1 year 2015/11/07 Temperature/ Meter Humidity Anymetre TH101B MRTSUE06047 1 year 2015/11/14 Radiated Emission Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date Spectrum Analyzer Agilent E4447A MRTSUE06028 1 year 2015/10/09 EMI Test Receiver R&S ESR7 MRTSUE06001 1 year 2015/11/07 Preamplifier Agilent 83017A MRTSUE06019 1 year 2015/12/13 TRILOG Antenna Schwarzbeck VULB9162 MRTSUE06022 1 year 2015/11/08 Broad-Band Horn Antenna Schwarzbeck BBHA9120D MRTSUE06023 1 year 2015/11/08 Temperature/Humidity Meter Anymetre TH101B MRTSUE06048 1 year 2015/11/14 Software Version Function e3 V 8.3.5 EMI Test Software (CE & RE) FCC ID: O9C-BJNGAFB0008 Page Number: 13 of 31

Report No.: 1503RSU02004 5. MEASUREMENT UNCERTAINTY Where relevant, the following test uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. AC Conducted Emission Measurement Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 150kHz~30MHz: 3.5dB Radiated Emission Measurement Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): Horizontal: 30MHz~1GHz: 4.07dB 1GHz~18GHz: 4.16 dB Vertical: 30MHz~1GHz: 4.18 dB 1GHz~18GHz: 4.76 dB FCC ID: O9C-BJNGAFB0008 Page Number: 14 of 31

Report No.: 1503RSU02004 6. TEST RESULT 6.1. Summary Company Name: Hewlett Packard Company FCC ID: O9C-BJNGAFB0008 FCC Classification: FCC Class B Digital Device (JBP) Test Mode: Communication FCC Part Section(s) Test Description Test Result 15.107 Conducted Emissions Pass 15.109 Radiated Emissions Pass FCC ID: O9C-BJNGAFB0008 Page Number: 15 of 31

Report No.: 1503RSU02004 6.2. Conducted Emission Measurement 6.2.1. Test Limit FCC Part 15.107 Limits Frequency QP AV (MHz) (dBμV) (dBμV) 0.15 - 0.50 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30 60 50 Note 1: The lower limit shall apply at the transition frequencies. Note 2: The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.5MHz. 6.2.2. Test Setup FCC ID: O9C-BJNGAFB0008 Page Number: 16 of 31

Report No.: 1503RSU02004 6.2.3. Test Result of Conducted Emissions Site: SR2 Time: 2015/04/19 - 17:09 Limit: FCC_Part15.107_CE_AC Power_ClassB Engineer: Milo Li Probe: ENV216_101683_Filter On Polarity: Line EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV) (dB) (dBuV) (dBuV) 1 0.166 42.735 32.648 -22.423 65.158 10.087 QP 2 0.166 30.439 20.352 -24.719 55.158 10.087 AV 3 0.434 43.345 33.232 -13.831 57.176 10.113 QP 4 * 0.434 35.093 24.979 -12.083 47.176 10.113 AV 5 15.022 37.881 27.817 -22.119 60.000 10.064 QP 6 15.022 18.009 7.945 -31.991 50.000 10.064 AV 7 16.550 41.192 31.115 -18.808 60.000 10.077 QP 8 16.550 23.177 13.100 -26.823 50.000 10.077 AV 9 17.830 39.297 29.203 -20.703 60.000 10.094 QP 10 17.830 21.331 11.237 -28.669 50.000 10.094 AV 11 29.986 40.884 30.614 -19.116 60.000 10.270 QP 12 29.986 14.016 3.746 -35.984 50.000 10.270 AV Note: Measure Level (dBμV) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + LISN Factor (dB) FCC ID: O9C-BJNGAFB0008 Page Number: 17 of 31

Report No.: 1503RSU02004 Site: SR2 Time: 2015/04/19 - 17:17 Limit: FCC_Part15.107_CE_AC Power_ClassB Engineer: Milo Li Probe: ENV216_101683_Filter On Polarity: Neutral EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV) (dB) (dBuV) (dBuV) 1 0.434 42.390 32.252 -14.786 57.176 10.138 QP 2 * 0.434 34.146 24.008 -13.030 47.176 10.138 AV 3 16.550 41.199 31.079 -18.801 60.000 10.120 QP 4 16.550 22.105 11.984 -27.895 50.000 10.120 AV 5 17.038 40.056 29.936 -19.944 60.000 10.120 QP 6 17.038 20.294 10.174 -29.706 50.000 10.120 AV 7 17.830 39.427 29.295 -20.573 60.000 10.132 QP 8 17.830 21.039 10.907 -28.961 50.000 10.132 AV 9 18.442 36.730 26.593 -23.270 60.000 10.137 QP 10 18.442 21.771 11.634 -28.229 50.000 10.137 AV 11 29.982 41.029 30.589 -18.971 60.000 10.440 QP 12 29.982 14.564 4.124 -35.436 50.000 10.440 AV Note: Measure Level (dBμV) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + LISN Factor (dB) FCC ID: O9C-BJNGAFB0008 Page Number: 18 of 31

Report No.: 1503RSU02004 Site: SR2 Time: 2015/04/19 - 17:23 Limit: FCC_Part15.107_CE_AC Power_ClassB Engineer: Milo Li Probe: ENV216_101683_Filter On Polarity: Line EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 2 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV) (dB) (dBuV) (dBuV) 1 0.154 45.523 34.784 -20.258 65.781 10.740 QP 2 0.154 33.247 22.507 -22.534 55.781 10.740 AV 3 0.426 43.771 33.664 -13.559 57.330 10.107 QP 4 0.426 35.421 25.314 -11.909 47.330 10.107 AV 5 11.302 37.074 26.976 -22.926 60.000 10.097 QP 6 11.302 31.760 21.662 -18.240 50.000 10.097 AV 7 19.478 41.315 31.182 -18.685 60.000 10.133 QP 8 19.478 40.368 30.235 -9.632 50.000 10.133 AV 9 27.654 43.545 33.301 -16.455 60.000 10.244 QP 10 * 27.654 43.176 32.932 -6.824 50.000 10.244 AV 11 28.854 42.200 31.924 -17.800 60.000 10.276 QP 12 28.854 41.638 31.362 -8.362 50.000 10.276 AV Note: Measure Level (dBμV) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + LISN Factor (dB) FCC ID: O9C-BJNGAFB0008 Page Number: 19 of 31

Report No.: 1503RSU02004 Site: SR2 Time: 2015/04/19 - 17:34 Limit: FCC_Part15.107_CE_AC Power_ClassB Engineer: Milo Li Probe: ENV216_101683_Filter On Polarity: Neutral EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 2 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV) (dB) (dBuV) (dBuV) 1 0.430 43.026 32.891 -14.227 57.253 10.135 QP 2 0.430 34.722 24.587 -12.531 47.253 10.135 AV 3 11.466 42.305 32.178 -17.695 60.000 10.127 QP 4 11.466 39.760 29.633 -10.240 50.000 10.127 AV 5 19.478 41.299 31.134 -18.701 60.000 10.165 QP 6 19.478 40.491 30.325 -9.509 50.000 10.165 AV 7 19.958 40.446 30.276 -19.554 60.000 10.170 QP 8 19.958 39.023 28.853 -10.977 50.000 10.170 AV 9 27.654 43.497 33.120 -16.503 60.000 10.377 QP 10 * 27.654 42.778 32.401 -7.222 50.000 10.377 AV 11 28.858 42.508 32.079 -17.492 60.000 10.429 QP 12 28.858 42.095 31.666 -7.905 50.000 10.429 AV Note: Measure Level (dBμV) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + LISN Factor (dB) FCC ID: O9C-BJNGAFB0008 Page Number: 20 of 31

Report No.: 1503RSU02004 6.3. Radiated Emission Measurement 6.3.1. Test Limit FCC Part 15.109 Limits Frequency Distance Level (MHz) (m) (dBμV/m) 30 - 88 3 40 88 - 216 3 43.5 216 - 960 3 46 Above 960 3 54 Note 1: The lower limit shall apply at the transition frequency. Note 2: Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. Note 3: E field strength (dBμV/m) = 20 log E field strength (uV/m) 6.3.2. Test Setup 30MHz ~ 1GHz Test Setup: FCC ID: O9C-BJNGAFB0008 Page Number: 21 of 31

1~4 m (Antenna Tower) Et l Antenna (Turntable) Pre—Amplifier s

Report No.: 1503RSU02004 6.3.3. Test Result of Radiated Emissions Site: AC1 Time: 2015/04/20 - 10:10 Limit: FCC_Part15.109_RE(3m)_ClassB Engineer: Milo Li Probe: VULB9162_0.03-8GHz Polarity: Horizontal EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 * 192.490 36.999 25.100 -6.501 43.500 11.899 QP 2 423.340 36.845 19.860 -9.155 46.000 16.985 QP 3 429.750 37.492 20.430 -8.508 46.000 17.062 QP 4 508.025 31.132 12.800 -14.868 46.000 18.332 QP 5 514.302 35.977 17.540 -10.023 46.000 18.437 QP 6 897.103 27.021 3.060 -18.979 46.000 23.961 QP Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: O9C-BJNGAFB0008 Page Number: 23 of 31

Report No.: 1503RSU02004 Site: AC1 Time: 2015/04/20 - 10:12 Limit: FCC_Part15.109_RE(3m)_ClassB Engineer: Milo Li Probe: VULB9162_0.03-8GHz Polarity: Vertical EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 30.310 28.777 16.700 -11.223 40.000 12.077 QP 2 41.602 29.968 15.820 -10.032 40.000 14.148 QP 3 192.520 28.701 16.800 -14.799 43.500 11.901 QP 4 442.500 34.840 17.620 -11.160 46.000 17.220 QP 5 * 500.040 38.400 20.170 -7.600 46.000 18.230 QP 6 950.110 36.990 12.630 -9.010 46.000 24.361 QP Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: O9C-BJNGAFB0008 Page Number: 24 of 31

Report No.: 1503RSU02004 Site: AC1 Time: 2015/04/20 - 10:06 Limit: FCC_Part15.109_RE(3m)_ClassB Engineer: Milo Li Probe: VULB9162_0.03-8GHz Polarity: Horizontal EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 2 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 194.780 30.154 18.120 -13.346 43.500 12.034 QP 2 280.210 35.995 21.850 -10.005 46.000 14.145 QP 3 323.230 32.666 17.560 -13.334 46.000 15.106 QP 4 423.300 32.704 15.720 -13.296 46.000 16.984 QP 5 520.650 34.875 16.350 -11.125 46.000 18.524 QP 6 * 559.670 38.861 19.620 -7.139 46.000 19.241 QP Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: O9C-BJNGAFB0008 Page Number: 25 of 31

Report No.: 1503RSU02004 Site: AC1 Time: 2015/04/20 - 10:06 Limit: FCC_Part15.109_RE(3m)_ClassB Engineer: Milo Li Probe: VULB9162_0.03-8GHz Polarity: Vertical EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 2 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 * 33.860 36.403 23.690 -3.597 40.000 12.713 QP 2 34.670 35.727 22.870 -4.273 40.000 12.857 QP 3 250.010 36.838 23.210 -9.162 46.000 13.627 QP 4 450.030 34.375 17.040 -11.625 46.000 17.335 QP 5 514.330 38.316 19.878 -7.684 46.000 18.438 QP 6 559.870 37.175 17.930 -8.825 46.000 19.245 QP Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: O9C-BJNGAFB0008 Page Number: 26 of 31

Report No.: 1503RSU02004 Site: AC1 Time: 2015/04/17 - 19:35 Limit: FCC_Part15.109_RE(3m)_ClassB Engineer: Milo Li Probe: BBHA9120D_1-18GHz Polarity: Horizontal EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 * 1246.240 37.654 46.240 -16.346 54.000 -8.586 AV 2 1246.500 43.952 52.536 -30.048 74.000 -8.583 PK 3 3184.260 30.882 32.460 -23.118 54.000 -1.578 AV 4 3184.500 41.497 43.076 -32.503 74.000 -1.579 PK 5 3363.000 40.995 42.819 -33.005 74.000 -1.824 PK 6 3364.210 30.191 32.010 -23.809 54.000 -1.819 AV Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) – Pre_Amplifier Gain (dB). FCC ID: O9C-BJNGAFB0008 Page Number: 27 of 31

Report No.: 1503RSU02004 Site: AC1 Time: 2015/04/17 - 19:35 Limit: FCC_Part15.109_RE(3m)_ClassB Engineer: Milo Li Probe: BBHA9120D_1-18GHz Polarity: Vertical EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 1246.500 46.042 54.626 -27.958 74.000 -8.583 PK 2 * 1250.030 39.508 48.060 -14.492 54.000 -8.552 AV 3 1680.000 40.828 48.394 -33.172 74.000 -7.566 PK 4 1680.040 27.834 35.400 -26.166 54.000 -7.566 AV 5 3363.000 44.341 46.165 -29.659 74.000 -1.824 PK 6 3363.080 32.096 33.920 -21.904 54.000 -1.824 AV Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) – Pre_Amplifier Gain (dB). FCC ID: O9C-BJNGAFB0008 Page Number: 28 of 31

Report No.: 1503RSU02004 Site: AC1 Time: 2015/04/15 - 11:17 Limit: FCC_Part15.109_RE(3m)_ClassB Engineer: Jame Probe: BBHA9120D_1-18GHz Polarity: Horizontal EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 2 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 3363.000 40.182 42.006 -33.818 74.000 -1.824 PK 2 3363.108 26.777 28.600 -27.223 54.000 -1.824 AV 3 3915.500 39.397 39.163 -34.603 74.000 0.234 PK 4 3915.810 24.925 24.690 -29.075 54.000 0.235 AV 5 * 9185.410 36.579 26.540 -17.421 54.000 10.039 AV 6 9185.500 48.262 38.222 -25.738 74.000 10.039 PK Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) – Pre_Amplifier Gain (dB). FCC ID: O9C-BJNGAFB0008 Page Number: 29 of 31

Report No.: 1503RSU02004 Site: AC1 Time: 2015/04/15 - 11:17 Limit: FCC_Part15.109_RE(3m)_ClassB Engineer: Jame Probe: BBHA9120D_1-18GHz Polarity: Vertical EUT: Wireless LAN Access Point Power: AC 120V/60Hz Note: Mode 2 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 * 1246.480 29.816 38.400 -24.184 54.000 -8.585 AV 2 1246.500 42.835 51.419 -31.165 74.000 -8.583 PK 3 1680.000 41.398 48.964 -32.602 74.000 -7.566 PK 4 1680.060 29.604 37.170 -24.396 54.000 -7.566 AV 5 3363.000 41.924 43.748 -32.076 74.000 -1.824 PK 6 3363.084 27.676 29.500 -26.324 54.000 -1.824 AV Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) – Pre_Amplifier Gain (dB). FCC ID: O9C-BJNGAFB0008 Page Number: 30 of 31

Report No.: 1503RSU02004 7. CONCLUSION The data collected relate only the item(s) tested and show that the Wireless LAN Access Point FCC ID: O9C-BJNGAFB0008 has been tested to comply with the requirements specified in §15.107 and §15.109 of the FCC Rules. The End FCC ID: O9C-BJNGAFB0008 Page Number: 31 of 31


Document Created: 2015-06-09 10:38:16
Document Modified: 2015-06-09 10:38:16
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC