LCS190923018AEF_WCDMA

FCC ID: O55503719

Test Report

Download: PDF

FCCID_4507277

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

TEST REPORT

October 28, 2019
Test Report No. : LCS190923018AEF ______________________________________________________________________________________________

Date of issue

Equipment under Test : 5 inch 4G Smart Phone

Test Model : L50T

Listed Models : VICTORY, N50T

: PCB board, structure and internal of these models are the same,
Model Declaration
So no additional models were tested.

Applicant : SWAGTEK
Address : 10205 NW 19th St. STE101, Miami, Florida, United States, 33172

Manufacturer : SWAGTEK
Address : 10205 NW 19th St. STE101, Miami, Florida, United States, 33172

Factory : SWAGTEK
Address : 10205 NW 19th St. STE101, Miami, Florida, United States, 33172

Test Result: PASS

The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test laboratory.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 2 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

Revison History
Revision Issue Date Revisions Revised By
000 October 28, 2019 Initial Issue Gavin Liang

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

Contents

1 TEST STAND ARDS .................................................................. 5

2 SUMM ARY ............................................................................. 6

2.1 General Remarks 6
2.2 Product Description 6
2.3 Equipment under Test 7
2.4 Short description of the Equipment under Test (EUT) 7
2.5 Internal Identification of AE used during the test 7
2.6 Normal Accessory setting 7
2.7 EUT configuration 8
2.8 Related Submittal(s) / Grant (s) 8
2.9 Modifications 8
2.10 General Test Conditions/Configurations 8

3 TEST ENVIRONMENT .............................................................. 9

3.1 Address of the test laboratory 9
3.2 Test Facility 9
3.3 Environmental conditions 9
3.4 Test Description 9
3.5 Equipments Used during the Test 11
3.6 Measurement uncertainty 12

4 TEST CONDITIONS AND RESULTS ........................................... 13

4.1 Output Power 13
4.2 Radiated Spurious Emssion 16
4.3 Occupied Bandwidth and Emission Bandwith 19
4.4 Band Edge Compliance 21
4.5 Spurious Emssion on Antenna Port 23
4.6 Frequency Stability Test 29
4.7 Peak-to-Average Ratio (PAR) 31

5 TEST SETUP PHOTOS OF THE EUT.......................................... 33

6 EXTERNAL PHOTOS OF THE EUT ............................................ 33

7 INTERNAL PHOTOS OF THE EUT ............................................. 33

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

1 TEST STANDARDS

The tests were performed according to following standards:

FCC Part 22 (10-1-16 Edition): Private Land Mobile Radio Services.
FCC Part 24(10-1-16 Edition): Public Mobile Services.
FCC Part 27(10-1-16 Edition): Public Mobile Services.
TIA-603-E March 2016: Land Mobile FM or PM Communications Equipment Measurement and Performance
Standards.
47 CFR FCC Part 15 Subpart B: Unintentional Radiators.
FCC Part 2: Frequency Allocations And Radio Treaty Matters: General Rules And Regulations.
ANSI C63.4:2014: Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electronic Equipment in the Range of 9 kHz to 40 GHz.
FCCKDB971168D01 Power Meas License Digital Systems

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

2 SUMMARY
2.1 General Remarks
Date of receipt of test sample : September 23, 2019

Testing commenced on : September 23, 2019

Testing concluded on : October 25, 2019
2.2 Product Description
The SWAGTEK’s Model: L50T or the “EUT” as referred to in this report; more general information as follows,
for more details, refer to the user’s manual of the EUT.
Name of EUT 5 inch 4G Smart Phone
Test Model L50T
Additional Models VICTORY, N50T
PCB board, structure and internal of these models are the same,
Models Declaration
So no additional models were tested.
GMSK for GSM/GPRS; 8-PSK for EDGE; QPSK for UMTS;
Modulation Type
QPSK and 16QAM for LTE
-0.93dBi (max.) For GSM 850;
1.09dBi (max.) For PCS 1900;
1.09dBi for WCDMA Band II;
Antenna Gain -0.93dBi for WCDMA Band V;
1.09dBi for LTE Band 2; 0.64dBi for LTE Band 4;
-0.93dBi for LTE Band 5; -0.90dBi for LTE Band 17;
1.03dBi (max.) For BT and WLAN
Hardware version FS273-V1.0B
Software version V1.0
GSM/EDGE/GPRS Operation
GSM850/PCS1900/GPRS850/GPRS1900/EDGE850/EDGE1900
Frequency Band
UMTS Operation Frequency Band UMTS FDD Band II / V
LTE Operation Frequency Band LTE FDD band 2, 4, 5, 17
GSM/EDGE/GPRS Supported GSM/GPRS/EDGE
GSM Release Version R99
GSM/EDGE/GPRS Power Class GSM850:Power Class 4/ PCS1900:Power Class 1
GPRS/EDGE Multislot Class GPRS/EDGE: Multi-slot Class 12
GPRS operation mode Class B
WCDMA Release Version R8
HSDPA Release Version Release 8
HSUPA Release Version Release 6
DC-HSUPA Release Version Not Supported
LTE Release Version R9
LTE/UMTS Power Class Class 3
IEEE 802.11b: DSSS(CCK,DQPSK,DBPSK)
WLAN FCC Modulation Type
IEEE 802.11g/n: OFDM(64QAM, 16QAM, QPSK, BPSK)
IEEE 802.11b:2412-2462MHz
WLAN FCC Operation frequency IEEE 802.11g/n20:2412-2462MHz
IEEE 802.11n40:2422-2452MHz
Antenna Type PIFA Antenna
BT Modulation Type GFSK, π/4-DQPSK, 8-DPSK (BT V4.2)
Extreme temp. Tolerance -20°C to +55°C
GPS function Support and only RX
FM function Support and only RX
NFC Function Not Supported
Extreme vol. Limits 3.40VDC to 4.30VDC (nominal: 3.80VDC)

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 6 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

2.7 EUT configuration
The following peripheral devices and interface cables were connected during the measurement:

● - supplied by the manufacturer

○ - supplied by the lab

○ Power Cable Length (m) : /
Shield : /
Detachable : /
○ Multimeter Manufacturer : /
Model No. : /

2.8 Related Submittal(s) / Grant (s)
This submittal(s) (test report) is intended for FCC ID: O55503719 filing to comply with FCC Part 22 and Part 24
Rules.

2.9 Modifications
No modifications were implemented to meet testing criteria.

2.10 General Test Conditions/Configurations

2.10.1 Test Modes

NOTE: The test mode(s) are selected according to relevant radio technology specifications.

Test Mode Test Modes Description
UMTS/TM1 WCDMA system, QPSK modulation
UMTS/TM2 HSDPA system, QPSK modulation
UMTS/TM3 HSUPA system, QPSK modulation

Note:
1. This EUT owns two SIM cards, SIM 1 support GSM/UMTS/LTE, SIM 2 support GSM;
2. We meausred conducted power at both SIM 1 and SIM 2, recorded worst case at SIM 1, after pre-check, we
measured other items at SIM 1;
3. As WCDMA, HSDPA and HSUPA with the same emission designator, test result recorded in this report at
the worst case UMTS/TM1 only after exploratory scan.

2.10.2 Test Environment
Environment Parameter Selected Values During Tests
Relative Humidity Ambient
Temperature TN Ambient
VL 3.40V
Voltage VN 3.85V
VH 4.30V

NOTE: VL=lower extreme test voltage VN=nominal voltage
VH=upper extreme test voltage TN=normal temperature

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 8 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

3 TEST ENVIRONMENT

3.1 Address of the test laboratory
Shenzhen LCS Compliance Testing Laboratory Ltd

1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong,
China
The sites are constructed in conformance with the requirements of ANSI C63.4 (2014) and CISPR
Publication 22.

3.2 Test Facility
The test facility is recognized, certified, or accredited by the following organizations:

FCC Registration Number. is 254912.
Industry Canada Registration Number. is 9642A-1.
ESMD Registration Number. is ARCB0108.
UL Registration Number. is 100571-492.
TUV SUD Registration Number. is SCN1081.
TUV RH Registration Number. is UA 50296516-001
NVLAP Registration Code is 600167-0

3.3 Environmental conditions
During the measurement the environmental conditions were within the listed ranges:

Temperature: 15-35 °C

Humidity: 30-60 %

Atmospheric pressure: 950-1050mbar
(1)expressed at approximately the 95% confidence level using a coverage factor of k=1.96.

3.4 Test Description

3.4.1 Cellular Band (824-849MHz paired with 869-894MHz) (Band V)
Test Item FCC Rule No. Requirements Verdict
Effective(Isotropic) Radiated §2.1046,
FCC: ERP ≤ 7W. Pass
Output Power §22.913
Modulation Characteristics §2.1047 Digital modulation N/A
OBW: No limit.
Bandwidth §2.1049 Pass
EBW: No limit.
≤-13dBm/1%*EBW, in 1MHz bands
§2.1051,
Band Edges Compliance immediately outside and adjacent to Pass
§22.917
The frequency block.
≤ -13dBm/100kHz,
Spurious Emission at Antenna §2.1051, th
from 9kHz to 10 harmonics but outside Pass
Terminals §22.917
authorized operating frequency ranges.
Field Strength of Spurious §2.1053,
≤ -13dBm/100kHz. Pass
Radiation §22.917
§2.1055,
Frequency Stability ≤ ±2.5ppm. Pass
§22.355
Peak-Average Ratio §24.232 ≤13dB Pass
NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” de notes “not tested”.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

3.4.2 PCS Band (1850-1915MHz paired with 1930-1995MHz) (Band II)
Test Item FCC Rule No. Requirements Verdict
Effective(Isotropic) Radiated §2.1046,
EIRP ≤ 2W Pass
Output Power §24.232
§2.1046,
Peak-Average Ratio ≤13dB Pass
§24.232
Modulation Characteristics §2.1047 Digital modulation N/A
OBW: No limit.
Bandwidth §2.1049 Pass
EBW: No limit.
≤ -13dBm/1%*EBW, In 1MHz bands
§2.1051,
Band Edges Compliance immediately outside and adjacent to Pass
§24.238
The frequency block.
th
≤-13dBm/1MHz, from 9kHz to10
Spurious Emission at Antenna §2.1051,
harmonics but outside authorized Pass
Terminals §24.238
operating frequency ranges.
Field Strength of Spurious §2.1053,
≤ -13dBm/1MHz. Pass
Radiation §24.238
§2.1055,
Frequency Stability ≤ ±2.5ppm. Pass
§24.235
NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” de notes “not tested”.

Remark: 1.The measurement uncertainty is not included in the test result.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 10 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

3.6 Measurement uncertainty
The data and results referenced in this document are true and accurate. The reader is cautioned that there may
be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was
calculated for all measurements listed in this test report acc. to ETSI TR 100 028 “ Electromagnetic
compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment
characteristics” and is documented in the Shenzhen LCS Compliance Testing Laboratory Ltd. quality system
acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested
may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the
device.

Hereafter the best measurement capability for Shenzhen LCS Compliance Testing Laboratory Ltd. is reported:

Measurement
Test Range Notes
Uncertainty
Radiated Emission 30~1000MHz 3.10 dB (1)
Radiated Emission 1~18GHz 3.80 dB (1)
Radiated Emission 18-40GHz 3.90 dB (1)
Conducted Disturbance 0.15~30MHz 1.63 dB (1)
Conducted Power 9KHz~18GHz 0.61 dB (1)
Spurious RF Conducted Emission 9KHz~40GHz 1.22 dB (1)
Band Edge Compliance of RF Emission 9KHz~40GHz 1.22 dB (1)
Occuiped Bandwidth 9KHz~40GHz - (1)

(1) This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level
using a coverage factor of k=1.96.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 12 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

to not interfere with the radiation pattern of the antenna. A power (PMea) is applied to the input of the
substitution antenna, and adjust the level of the signal generator output until the value of the receiver reach
the previously recorded (Pr). The power of signal source (PMea) is recorded. The test should be performed
by rotating the test item and adjusting the receiving antenna polarization.
5. A amplifier should be connected to the Signal Source output port. And the cable should be connect between
the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain (Ga) and the
Amplifier Gain (PAg) should be recorded after test.
The measurement results are obtained as described below:
Power(EIRP)=PMea+ PAg - Pcl + Ga
6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and
known input power.
7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP-2.15dBi.

TEST LIMIT

According to 22.913(a)(5), 24.232(c), the ERP(EIRP) should be not exceeding following table limits:
Burst Average EIRP
UMTS Band II FCC: ≤33.01dBm (2W)

Burst Average ERP
UMTS Band V FCC: ≤38.45dBm (7W)

TEST RESULTS

Remark:
1. We were tested all Configuration refer 3GPP TS134 121.
2. EIRP=PMea(dBm)-Pcl(dB)+PAg(dB)+Ga(dBi)
3. ERP = EIRP – 2.15dBi as EIRP by subtracting the gain of the dipole.
4. Margin = Emission Level - Limit
5. We test the H direction and V direction recorded worst case.

UMTS/TM1/UMTS Band II
Ga Burst
Frequency PMea Pcl Antenna PAg Average Limit Margin
Polarization
(MHz) (dBm) (dB) Gain (dB) EIRP (dBm) (dB)
(dB) (dBm)
1852.40 -18.80 4.03 8.38 35.51 21.06 33.00 -11.94 V
1880.00 -18.51 4.08 8.33 35.56 21.30 33.00 -11.70 V
1907.60 -18.55 4.14 8.26 35.63 21.20 33.00 -11.80 V

UMTS/TM1/UMTS Band V
Ga Burst
Frequency PMea Pcl Antenna Correction PAg Average Limit Margin
Polarization
(MHz) (dBm) (dB) Gain (dB) (dB) ERP (dBm) (dB)
(dB) (dBm)
826.40 -16.40 3.45 8.45 2.15 33.79 20.24 38.45 -18.21 V
836.40 -16.18 3.49 8.45 2.15 33.85 20.48 38.45 -17.97 V
846.60 -16.18 3.55 8.36 2.15 33.88 20.36 38.45 -18.09 V

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 15 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

5. A amplifier should be connected to the Signal Source output port. And the cable should be connect between
the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain (Ga) and the
Amplifier Gain (PAg) should be recorded after test.
The measurement results are obtained as described below:
Power(EIRP)=PMea+ PAg - Pcl + Ga
6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and
known input power.
7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP -2.15dBi.
8. In order to make sure test results more clearly,we set frequency range and sweep time for difference
frequency range as follows table:

Working Subrange Sweep time
RBW VBW
Frequency (GHz) (s)
0.00009~0.15 1KHz 3KHz 30
0.00015~0.03 10KHz 30KHz 10
0.03~1 100KHz 300KHz 10
UMTS/TM1/
1~2 1 MHz 3 MHz 2
WCDMA Band V
2~5 1 MHz 3 MHz 3
5~8 1 MHz 3 MHz 3
8~10 1 MHz 3 MHz 3
0.00009~0.15 1KHz 3KHz 30
0.00015~0.03 10KHz 30KHz 10
0.03~1 100KHz 300KHz 10
1~2 1 MHz 3 MHz 2
UMTS/TM1/ 2~5 1 MHz 3 MHz 3
WCDMA Band II 5~8 1 MHz 3 MHz 3
8~11 1 MHz 3 MHz 3
11~14 1 MHz 3 MHz 3
14~18 1 MHz 3 MHz 3
18~20 1 MHz 3 MHz 2

TEST LIMITS

According to 24.238, 22.917 and 27.54 specify that the power of any emission outside of the authorized
operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10
log(P) dB.
The specification that emissions shall be attenuated below the transmitter power (P) by at least 43 + 10 log (P)
dB, translates in the relevant power range (1 to 0.001 W) to -13 dBm. At 1 W the specified minimum attenuation
becomes 43 dB and relative to a 30 dBm (1 W) carrier becomes a limit of -13 dBm. At 0.001 W (0 dBm) the
minimum attenuation is 13 dB, which again yields a limit of -13 dBm. In this way a translation of the specification
from relative to absolute terms is carried out.

Frequency Channel Frequency Range Verdict
Low 9KHz - 10GHz PASS
UMTS/TM1/ WCDMA
Middle 9KHz - 10GHz PASS
Band V
High 9KHz - 10GHz PASS
Low 9KHz - 20GHz PASS
UMTS/TM1/ WCDMA
Middle 9KHz - 20GHz PASS
Band II
High 9KHz - 20GHz PASS

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 17 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

TEST RESULTS

Remark:
1. We were tested all Configuration refer 3GPP TS134 121.
2. EIRP=PMea(dBm)-Pcl(dB)+PAg(dB)+Ga(dBi)
3. ERP = EIRP – 2.15dBi as EIRP by subtracting the gain of the dipole.
4. Margin = EIRP - Limit

UMTS/TM1/ WCDMA Band II _ Low Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
3704.8 -43.88 5.26 3.00 9.88 -39.26 -13.00 -26.26 H
5557.2 -48.06 6.11 3.00 11.36 -42.81 -13.00 -29.81 H
3704.8 -47.12 5.26 3.00 9.88 -42.50 -13.00 -29.50 V
5557.2 -50.96 6.11 3.00 11.36 -45.71 -13.00 -32.71 V

UMTS/TM1/ WCDMA Band II _ Middle Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
3760.0 -42.82 5.32 3.00 10.03 -38.11 -13.00 -25.11 H
5640.0 -45.89 6.19 3.00 11.41 -40.67 -13.00 -27.67 H
3760.0 -46.98 5.32 3.00 10.03 -42.27 -13.00 -29.27 V
5640.0 -51.47 6.19 3.00 11.41 -46.25 -13.00 -33.25 V

UMTS/TM1/ WCDMA Band II _ High Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
3815.2 -41.37 5.36 3.00 9.62 -37.11 -13.00 -24.11 H
5722.8 -44.33 6.24 3.00 11.46 -39.11 -13.00 -26.11 H
3815.2 -45.74 5.36 3.00 9.62 -41.48 -13.00 -28.48 V
5722.8 -47.34 6.24 3.00 11.46 -42.12 -13.00 -29.12 V

UMTS/TM1/ WCDMA Band V _ Low Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
1652.8 -46.27 3.86 3.00 8.56 -41.57 -13.00 -28.57 H
2479.2 -46.95 4.29 3.00 6.98 -44.26 -13.00 -31.26 H
1652.8 -45.36 3.86 3.00 8.56 -40.66 -13.00 -27.66 V
2479.2 -48.52 4.29 3.00 6.98 -45.83 -13.00 -32.83 V

UMTS/TM1/ WCDMA Band V _ Middle Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
1672.8 -46.15 3.90 3.00 8.58 -41.47 -13.00 -28.47 H
2509.2 -46.69 4.32 3.00 6.80 -44.21 -13.00 -31.21 H
1672.8 -46.18 3.90 3.00 8.58 -41.50 -13.00 -28.50 V
2509.2 -49.66 4.32 3.00 6.80 -47.18 -13.00 -34.18 V

UMTS/TM1/ WCDMA Band V _ High Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
1693.2 -44.27 3.91 3.00 9.06 -39.12 -13.00 -26.12 H
2539.8 -45.51 4.32 3.00 6.65 -43.18 -13.00 -30.18 H
1693.2 -45.92 3.91 3.00 9.06 -40.77 -13.00 -27.77 V
2539.8 -47.92 4.32 3.00 6.65 -45.59 -13.00 -32.59 V

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 18 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

TEST RESULTS

Frequency Spurious RF Conducted Emission Limits
Test Mode Channel Verdict
(MHz) (dBm) (dBm)
9262 1852.40 <-13dBm -13dBm
UMTS/TM1/WCDMA
9400 1880.00 <-13dBm -13dBm PASS
Band II
9538 1907.60 <-13dBm -13dBm
4132 826.40 <-13dBm -13dBm
UMTS/TM1/WCDMA
4182 836.40 <-13dBm -13dBm PASS
Band V
4233 846.60 <-13dBm -13dBm

Remark:
1. Test results including cable loss;
2. Please refer to following plots;
3. Not reorded test plots from 9 KHz to 30 MHz as emission levels 20dB lower than emission limit;

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 24 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

TEST LIMITS

For Hand carried battery powered equipment
According to the JTC standard the frequency stability of the carrier shall be accurate to within 0.1 ppm of the
received frequency from the base station. This accuracy is sufficient to meet Sec. 24.235, Frequency Stability.
The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized
frequency block. As this transceiver is considered "Hand carried, battery powered equipment" Section
2.1055(d)(2) applies. This requires that the lower voltage for frequency stability testing be specified by the
manufacturer. This transceiver is specified to operate with an input voltage of between 3.40VDC and 4.30VDC,
with a nominal voltage of 3.80DC. Operation above or below these voltage limits is prohibited by transceiver
software in order to prevent improper operation as well as to protect components from overstress. These
voltages represent a tolerance of -10 % and +12.5 %. For the purposes of measuring frequency stability these
voltage limits are to be used.

For equipment powered by primary supply voltage
According to the JTC standard the frequency stability of the carrier shall be accurate to within 0.1 ppm of the
received frequency from the base station. This accuracy is sufficient to meet Sec. 24.235, Frequency Stability.
The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized
frequency block. For this EUT section 2.1055(d)(1) applies. This requires varying primary supply voltage from
85 to 115 percent of the nominal value for other than hand carried battery equipment.

TEST RESULTS

UMTS/TM1/WCDMA Band II
Temperature Frequency Frequency Limit
DC Power Verdict
(℃) error(Hz) error(ppm) (ppm)
3.40 25 21 0.011 ±2.50 PASS
3.80 25 -6 -0.003 ±2.50 PASS
4.30 25 49 0.026 ±2.50 PASS
3.80 -30 9 0.005 ±2.50 PASS
3.80 -20 -52 -0.028 ±2.50 PASS
3.80 -10 19 0.010 ±2.50 PASS
3.80 0 -20 -0.011 ±2.50 PASS
3.80 10 -27 -0.015 ±2.50 PASS
3.80 20 58 0.031 ±2.50 PASS
3.80 30 -57 -0.030 ±2.50 PASS
3.80 40 30 0.016 ±2.50 PASS
3.80 50 24 0.013 ±2.50 PASS

UMTS/TM1/WCDMA Band V
Temperature Frequency Frequency Limit
DC Power Verdict
(℃) error(Hz) error(ppm) (ppm)
3.40 25 31 0.037 ±2.50 PASS
3.80 25 46 0.055 ±2.50 PASS
4.30 25 19 0.023 ±2.50 PASS
3.80 -30 40 0.048 ±2.50 PASS
3.80 -20 49 0.059 ±2.50 PASS
3.80 -10 -46 -0.055 ±2.50 PASS
3.80 0 53 0.063 ±2.50 PASS
3.80 10 20 0.023 ±2.50 PASS
3.80 20 42 0.051 ±2.50 PASS
3.80 30 -36 -0.043 ±2.50 PASS
3.80 40 -3 -0.003 ±2.50 PASS
3.80 50 20 0.024 ±2.50 PASS

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 30 of 33

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: O55503719 Report No.: LCS190923018AEF

5 Test Setup Photos of the EUT

Please refer to separated files for Test Setup Photos of the EUT.

6 External Photos of the EUT

Please refer to separated files for External Photos of the EUT.

7 Internal Photos of the EUT

Please refer to separated files for Internal Photos of the EUT.

.........................End of Report.........................

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 33 of 33

Document Created: 2019-11-04 19:28:12
Document Modified: 2019-11-04 19:28:12

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC