LCS190923018AEB_SAR_REPORT_4

FCC ID: O55503719

RF Exposure Info

Download: PDF
FCCID_4507274

((( . \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.287.6.14.8ATU.A SATIMO 7 VALIDATION MEASUREMENT The IEEE Std. 1528, OET 65 Bulletin C and CEIIEC 62209 standards state that the system validation measurements must be performed using a reference dipole meeting the fore mentioned return loss and mechanical dimension requirements. The validation measurement must be performed against a liquid filled flat phantom, with the phantom constructed as outlined in the fore mentioned standards. Per the standards, the dipole shall be positioned below the bottom of the phantom, with the dipole length centered and parallel to the longest dimension of the flat phantom, with the top surface of the dipole at the described distance from the bottom surface of the phantom. 7.1 HEAD LIQUID MEASUREMENT Fre’?/lu:zncy Relative permittivity (€,‘) Conductivity {0) S/m required measured required measured 300 45.3 15 % 0.87 £5 % 450 43.5 25 % 0.87 £5 % 750 41.9 25 % 0.89 £5 % 835 41.5 25 % 0.90 £5 % 900 41.5 25 % 0.97 £5 % 1450 40.5 45 % 1.20 25 % 1500 40.4 15 % 123125 % 1640 40.2 25 % 1.31 15 % 1750 40.1 25 % 1.37 25 % 1800 40.0 25 % PASS 1.40 25 % PASS 1900 40.0 25 % 1.40 25 % 1950 40.0 25 % 140 £5 % 2000 40.0 25 % 140 25 % 2100 39.8 45 % 149 £5 % 2300 39.5 25 % 1.67 25 % 2450 39.2 25 % 1.80 25 % 2600 39.0 25 % 1.96 25 % 3000 38.5 15 % 2.40 £5 % 3500 37.9 25 % 2.91 +5 % 7.2 SAR MEASUREMENT RESULT WITH HEAD LIQUID The IEEE Std. 1528 and CEUIEC 62209 standards state that the system validation measurements should produce the SAR values shown below (for phantom thickness of 2 mm), within the uncertainty for the system validation. All SAR values are normalized to 1 W forward power. In bracket, the measured SAR is given with the used input power. Software OPENSAR V4 Phantom SN 20/09 SAM71 Probe SN 18/11 BPG122 Liquid Head Liquid Values: eps‘ : 41.3 sigma : 1.38 Distance between dipole center and liquid 10.0 mm Area scan resolution dx=8mm/dy=8mm Page: 7/11 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO. ts nc y >

((/.\ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.287.6.14.SATU.A SATIMO Zoon Scan Resolution dx=8mm/dy=8m/dz=5mm Frequency 1800 MHz Input power 20 dBm Liquid Temperature 71 °C Lab Temperature 21 °C Lab Humidity 45 % F um* 1 g SAR (W/ke/w) 10 g SAR (W/kg/w) required measured required measured 300 2.85 1.94 450 4.58 3.06 750 8.49 $55 835 9.56 6.22 900 10.9 6.99 1450 29 16 1500 30.5 16.8 1640 34.2 184 1750 36.4 19.3 1800 38.4 38.13 (3.81) 20.1 20.20 (2.02) 1900 $9.7 20.5 1950 40.5 20.9 2000 41.1 21.1 2100 43.6 21.9 2300 48.7 23.3 2450 52.4 24 2600 55.3 24.6 3000 63.8 25.7 3500 67.1 25 Iemnmeame 7 Sutsen hssrerws _termos_| /,‘ C Sinkd ns fres s s hoe w# 8367 sos— J“T.vmm‘j g 400 .Z- «s L ;; 300 @ ] 200 we} gal) Ta on & n H égg_ 7 I [ ximet B Yieet 0 2 4 608 10 12 12‘[’"‘”3 18 20 22 2 % m 30 Page: 8/11 This document shall not be reproduced, except in full or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyforthe purpose for which it is submitted and is not to be released in whole orpart without written approval ofSATIMO. t nc y >

((ri A Ref: ACR.287.6.14.SATU.A SsArImMo SAR REFERENCE DIPOLE CALIBRATION REPORT 7.3 BODY LIQUID MEASUREMENT F re:,l":z"“’ Relative permittivity (€,‘) Conductivity (0) S/m required measured required measured 150 61.9 £5 % 0.80 £5 % 300 58.2 45 % 0.92 £5% 450 56.7 45 % 0.94 £5% 750 55.5 45 % 0.96 +5 % 835 55.2 45 % 0.97 £5 % 900 55.0 45 % 1.05 £5 % 915 55.0 45 % 1.06 £5 % 1450 54.0 £5 % 1.30 +5 % 1610 53.8 45 % 140 +5 % 1800 53.3 45 % PASS 1.52 45 % PASS 1900 53.3 45 % 1.52 45 % 2000 53.3 15 % 1.52 +5 % 2100 53.2 +5 % 1.62 +5 % 2450 52.7 45 % 1.95 +5 % 2600 52.5 45 % 21645 % 3000 52.0 45 % 2.73 45 % 3500 51.3 45 % 3.31 +5 % 5200 49.0 £10% 5.30 £10 % 5300 48.9 £10% 5.42£10% 5400 48.7 £10% 5.53 210 % 5500 48.6 £10% 5.65 £10 % 5600 48.5 £10% 5.77 £10% 5800 48.2 £10 % 6.00 £10% 74 SAR MEASUREMENT RESULT WITH BODY LIQUID Software OPENSAR V4 Phantom SN 20/09 SAM71 Probe SN 18/11 EPG122 Liquid Body Liquid Values: eps‘ : 53.3 sigma : 1.51 Distance between dipole center and liquid 10.0 mm Area scan resolution dx=8mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8m/dz=5mm Frequency 1800 MHz Input power 20 dBm Liquid Temperature 21 °C Lab Temperature 21 °C Lab Humidity 45 % Page: 9/11 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyfor the purpose for which it is submitted and is not to be released in whole orpart without written approval ofSATIMO.

SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.287.6.14.SATU.A F 'e:,l":zm" 1 g SAR (W/ke/w) 10 g SAR (W/kg/w) measured measured 1800 39.03 (3.90) 20.65 (2.07) udn haswe mesy Gincicw is £50 600— 500— SA(Whkai £00— 3007 200— 1.00 ass— 0 204 \U‘IENTETEZU?ZMESZE?IU BC xtBC viemt 2 jur) Page: 10/11 This document shall not be reproduced, except in full orin part, without the written approval ofSATIMO. The information contained herein is to be used onlyforthe purpose for which it is submitted and is not to be released in whole orpart without written approval ofSATIMO.

SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.287.6.14.SATU.A 8 LIST OF EQUIPMENT Equipment Summary Sheet Equipment Manufacturer / Identification No Current Next Calibration Description Model ‘| Calibration Date Date SAM Phantom Satimo sN—2009.sam7z4 Validated. No cal required. Validated. required. No cal COMOSAR Test Bench] Version 3 NA alidated. No cal required. alidated. required. No cal Network Analyzer RhOdegviChwarz sN100132 o2po16 022019 Calipers Carrera CALIPER—01 12/2016 12/2019 Reference Probe Satimo EPG122 SN 18/11 102018 10/2019 Multimeter Keithley 2000 1188656 1272016 12/2019 Signal Generator Agilent E4438C MY49070581 12/2016 12/2019 Amplifier Aethercomm SN 046 Characterized prior to |\Characterized prior to test. No cal required. |test. No cal required. Power Meter HP E4418A US38261498 12/2016 12/2019 Power Sensor HP ECP—E26A US37181460 12/2016 12/2019 Directional Coupler Narda 4216—20 o1386 Characterized prior to |\Characterized prior to test. No cal required. |test. No cal required. Temperature and Humidity Sensor Control Company 11—661—9 8/2016 872019 Page: 11/11 This document shall not be reproduced, except in full or in part, without the written approvalofSATIMO. The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO.

(GGaA SATIMD The microwave vision company_A SAR Reference Dipole Calibration Report Ref : ACR.262.8.14.SATU.A SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. 1F., XINGYUAN INDUSTRIAL PARK, TONGDA ROAD, BAO‘AN BLVD BAO‘AN DISTRAICT, SHENZHEN, GUANGDONG, CHINA SATIMO COMOSAR REFERENCE DIPOLE FREQUENCY: 1900 MHZ SERIAL NO.: SN 30/14 DIP1G900—333 Calibrated at SATIMO US 2105 Barrett Park Dr. — Kennesaw, GA 30144 \\II/ MQI/,-\\ ‘\? |Accnsmrsol ’t|\ > cem srmea 09/01/2018 Summ ary. This document presents the methodand results from an accredited SAR reference dipole calibration performed in SATIMO USA using the COMOSAR test bench. All calibration results are traceable to national metrologyinstitutions.

& SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.262.8.14.SATU.A SATIMD Name Function Date Signature Prepared by : Jérome LUC Product Manager 9/19/2018 fi’ Checked by: Jérome LUC Product Manager 9/19/2018 ;/lé’ Approved by: Kim RUTKOWSKI Quality Manager 9/19/2018 lum Pathneah) Customer Name Shenzhen LCS Distribution : Compliance Testing Laboratory Ltd. Issue Date Modifications A 9/19/2018 Initial release Page: 2/11 This document shall not be reproduced, except in full or in part, without the written approval ofSATIMO. The information contained hereinis to be used onlyforthepurposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO. ho nc ennnnmen neve nc ce gneeng en nermu mc w mp ce hp ces men e y se

({ ( \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.262.8.14.SATU.A sArImo TABLE OF CONTENTS ) IMfOducHO®:—mmmeormmmnmenememrmmmmnareroemenrarerermmarnmenmmemymmonmmernmnm 4 B DCVIC@ URCCF TESE ... ... s cmemimecmmmmmmmnnmncrmensecirmmmecmnnemmntrenmrermmrocremnmmmsnteernnccnczcne 4 3 PFOUUGCE DeSCFIPHON ... vemmememmmmommenmmmenmmnmierenmmenernmmmmeninmmmnrnememenisiimmmerier 4 3.1 General Information 4 #: MeASUROMeNENCHAIOU —:——+—msmemscommmrenecncerormemiermsnctisesmemseretemecmmetimmmemisrime $ 4.1 Return Loss Requirements 5 4.2 Mechanical Requirements 5 5 MEASUT@ME@Nt UNCETEANEY ... ... en eeemmeemeememeeeeeee n n en en en ernernenneernernerne en en enene. 5 5.1 Return Loss $ 5.2 Dimension Measurement § 5.3 Validation Measurement 5 6 CalibrAtiON MEASUT@MENE RESUIS .............2.nene e en en reeneeneemneeneen e 6 6.1 Return Loss and Impedance In Head Liquid 6 6.2 Return Loss and Impedance In Body Liquid 6 6.3 Mechanical Dimensions 6 7 VAIIGANON M@ASUT@MENE ........... .000 mmemeneemnemnmnemeemeemnernnenneeneennenn mm en 7 7.1 Head Liquid Measurement 7 7.2 SAR Measurement Result With Head Liquid 8 7.3 Body Liquid Measurement 9 74 SAR Measurement Result With Body Liquid 10 1.38t:0f BAUIPMIENE : :m mmmmmmmmmmmmmnmmormememmmememnmmmmummmememememmmmment 11 co Page: 3/11 This document shall not be reproduced, except in full or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyforthe purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO. ts cn n y >

(t( \ SAR REFERENCE DIPOLE CALIBRATION REPORT eMessq148ATDA 1 INTRODUCTION This document contains a summary of the requirements set forth by the IEEE 1528, OET 65 Bulletin C and CEVIEC 62209 standards for reference dipoles used for SAR measurement system validations and the measurements that were performed to verify that the product complies with the fore mentioned standards. 2 DEVICE UNDER TEST Device Under Test Device Type COMOSAR 1900 MHz REFERENCE DIPOLE Manufacturer Satimo Model $1D1900 Serial Number SN 30/14 DIP1G900—333 Product Condition (new / used) New A yearly calibration interval is recommended. 3 PRODUCT DESCRIPTION 3.1 GENERAL INFORMATION Satimo‘s COMOSAR Validation Dipoles are built in accordance to the IEEE 1528, OET 65 Bulletin C and CEIIEC 62209 standards. The product is designed for use with the COMOSAR test bench only. Figure 1 —Satimo COMOSAR Validation Dipole Page: 4/11 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO.

(((— \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.262 8.14.8ATU.A SATIMID 4 MEASUREMENT METHOD The IEEE 1528, OET 65 Bulletin C and CELIIEC 62209 standards provide requirements for reference dipoles used for system validation measurements. The following measurements were performed to verify that the product complies with the fore mentioned standards. 4.1 RETURN LOSS REQUIREMENTS The dipole used for SAR system validation measurements and checks must have a return loss of —20 dB or better. The return loss measurement shall be performed against a liquid filled flat phantom, with the phantom constucted as outlined in the fore mentioned standards. 4.2 MECHANICAL REQUIREMENTS The IEEE Std. 1528 and CEIMIEC 62209 standards specify the mechanical components and dimensions of the validation dipoles, with the dimensions frequency and phantom shell thickness dependent. The COMOSAR test bench employs a 2 mm phantom shell thickness therefore the dipoles sold for use with the COMOSAR test bench comply with the requirements set forth for a 2 mm phantom shell thickness. 5 MEASUREMENT UNCERTAINTY All uncertainties listed below represent an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2, traceable to the Internationally Accepted Guides to Measurement Uncertainty. 5.1 RETURNLOSS The following uncertainties apply to the return loss measurement: Frequency band Expanded Uncertainty on Return Loss 400—6000MHz 0.1 dB 5.2 DIMENSION MEASUREMENT The following uncertainties apply to the dimension measurements: Length (mm) Expanded Uncertainty on Length 3 — 300 0.05 mm 5.3 VALIDATION MEASUREMENT The guidelines outlined in the IEEE 1528, OET 65 Bulletin C, CENELEC EN50361 and CEIIEC 62209 standards were followed to generate the measurement uncertainty for validation measurements. Scan Volume Expanded Uncertainty 1 g 20.30% 10 g 20.1 % Page: 5/11 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO.

(L SATIMO / (. SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.262.8.14.SATU.A 6 CALIBRATION MEASUREMENT RESULTS 6.1 RETURN LOSS AND IMPEDANCE IN HEAD LIQUID Frequency, MHz 1800 1820 1840 1860 1880 1900 1920 1940 1960 1980 2000 o 2 9 40— Frequency (MHz) Return Loss (dB) Requirement (dB) Impedance 1900 —22.98 _ —20 | _50.9 t +6.7jG2 6.2 RETURN LOSS AND IMPEDANCE IN BODY LIQUID Frequency, MHz 1800 1820 1840 1860 1880 1900 1920 1940 1960 1980 2000 S11, dB ,30, Frequency (MHz) Return Loss (dB) _| Requirement (dB) Impedance 1900 —20.28 | —20 49.2 O +9.4 jC2 6.3 MECHANICAL DIMENSIONS Frequency MHz L mm h mm d mm required measured required measured required measured 300 420.0 £1 %. 250.0 £1 %. 6.35 £1 %. 450 290.0 £1 %. 166.7 +1 %. 6.35 £1 %. 750 176.0 #1 %. 100.0 #1 %. 6.35 £1 %. 835 161.0 +1 %. 89.8 £1 %. 3.6 +1 %. Page: 6/11 Thisdocument shall not be reproduced, except in full orin part, without the written approval ofSATIMO. The information contained hereinis to be used onlyforthe purposefor whichit is submitted and is not to be released in whole orpart without writtenapproval ofSATIMO ho nc ennnnmen neve nc ce gneeng en nermu mc w

(t( \ SAR REFERENCE DIPOLE CALIBRATION REPORT eMessq148ATDA sArimo 900 149.0 +1 %. 83.3 +1%. 3.6 41 %. 1450 89.1 +1 %. 51.741%. 3.6 +1 %. 1500 80.5 +1 %. 50.0 +1 %. 3.6 +1 %. 1640 79.0 +1 %. 45.7 41 %. 3.6 41 %. 1750 75.2 41 %. 42.9 41 %. 3.6 41 %. 1800 72.0 41 %. 41.7 41 %. 3.6 41 %. 1900 68.0 +1 %. PASS 39.5 £1%. PASS 3.6 1 %. PASS 1950 66.3 +1 %. 38.5 1 %. 3.6 41 %. 2000 64.5 41 %. 37.5 +1 %. 3.6 41 %. 2100 61.041%. 35.7 41 %. 3.6 41 %. 2300 55.5 +1 %. 32.6+1%. 3.6 +1 %. 2450 51.5 +1 %. 30.4 +1 %. 3.6 41 %. 2600 48.5 1 %. 28.8 £1%. 3.6 41 %. 3000 41.5 £1 %. 25.0 +1 %. 3.6 £1 %. 3500 37.041%. 264 +1 %. 3.6 +1 %. 3700 34.741%. 264 +1%. 3.6 +1 %. 7 VALIDATION MEASUREMENT The IEEE Std. 1528, OET 65 Bulletin C and CEVIEC 62209 standards state that the system validation measurements must be performed using a reference dipole meeting the fore mentioned return loss and mechanical dimension requirements. The validation measurement must be performed against a liquid filled flat phantom, with the phantom constructed as outlined in the fore mentioned standards. Per the standards, the dipole shall be positioned below the bottom of the phantom, with the dipole length centered and parallel to the longest dimension of the flat phantom, with the top surface of the dipole at the described distance from the bottom surface of the phantom. 7.1 HEAD LIQUID MEASUREMENT Fre&":z"“' Relative permittivity (€,‘) Conductivity (0) S/m required measured required measured 300 45.3 £5 % 0.87 £5 % 450 43.5 £5 % 0.87 £5 % 750 41.9 £5 % 0.89 £5 % 835 41.5 £5 % 0.90 £5 % 900 41.5 £5 % 0.97 £5 % 1450 40.5 £5 % 1.20 £5 % 1500 40.4 £5 % 1.23 £5 % 1640 40.2 £5 % 1.31 +5 % 1750 40.1 £5 % 1.37 £5 % 1800 40.0 £5 % 1.40 £5 % 1900 40.0 £5 % PASS 1.40 £5 % PASS 1950 40.0 £5 % 1.40 £5 % 2000 40.0 £5 % 1.40 £5 % Page: 7/11 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO. t cy >

S(t( \ SAR REFERENCE DIPOLE CALIBRATION REPORT eMessq148ATDA ATiIV,ID 2100 39.8 15 % 1.49 £5 % 2300 39.5 15 % 1.67 +5 % 2450 39.2 £5 % 1.80 +5 % 2600 39.0 £5 % 1.96 45 % 3000 38.5 15 % 2.40 £5 % 3500 37.9 £5 % 2.91 5 % 7.2 SAR MEASUREMENT RESULT WITH HEAD LIQUID The IEEE Std. 1528 and CEIIEC 62209 standards state that the system validation measurements should produce the SAR values shown below (for phantom thickness of 2 mm), within the uncertainty for the system validation. All SAR values are normalized to 1 W forward power. In bracket, the measured SAR is given with the used input power. Software OPENSAR V4 Phantom SN 20/09 SAM71 Probe SN 18/11 EPG122 Liquid Head Liquid Values: eps‘ : 41.1 sigma : 1.42 Distance between dipole center and liquid 10.0 mm Area scan resolution dx=8mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8m/dz=5mm Frequency 1900 MHz Input power 20 dBm Liquid Temperature 31 °C Lab Temperature 21 °C Lab Humidity 45 % F’*:A“:Z"“' 1 g SAR (W/ke/w) 10 g SAR (W/kg/w) required measured required measured 300 2.85 1.94 450 4.58 3.06 750 8.49 5.55 835 9.56 6.22 900 10.9 6.99 1450 29 16 1500 30.5 16.8 1640 34.2 18.4 1750 36.4 19.3 1800 38.4 20.1 1900 39.7 39.84 (3.98) 20.5 20.20 (2.02) 1950 40.5 20.9 2000 41.1 211 2100 43.6 21.9 2300 48.7 23.3 Page: 8/11 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO. t cy >

SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.262.8.14.SATU.A SATIMD 2450 52.4 24 2600 55.3 24.6 3000 63.8 25.7 3500 67.1 25 w mnnivent urcomeree / Sutewr Artwe wy incicw wa UR w £75 s00— 500 M 100 Ti > im wesrd 200— $it] e e | 1 i ¥imn 6 Ce 0 2 406 10 12 M 1P t M 2 M & m 0 Z (un) 7.3 BODY LIQUID MEASUREMENT F reslu:zncy Relative permittivity (€,‘) Conductivity 0) S/m required measured required measured 150 61.9 +5 % 0.80 +5 % 300 58.2 45 % 0.92 25 % 450 56.7 25 % 0.94 25 % 750 55.5 45 % 0.96 25 % 835 55.2 45 % 0.97 £5% 900 55.0 45 % 1.05 £5 % 913 55.0 45 % 1.06 45 % 1450 54.0 £5 % 1.30 +5 % 1610 53.8 45 % 14045 % 1800 53.3 45 % 1.52 45 % 1900 53.3 45 % PASS 1.52 +5 % PaSS 2000 53.3 45 % 1.52 45 % 2100 53.2 45 % 1.62 45 % 2450 52.7 45 % 1.95 £5 % 2600 52.5 45 % 216 45 % 3000 52.0 45 % 2.73 45 % 3500 51.3 45 % 3.31 45 % 5200 49.0 £10 % 5.30 £10 % 5300 48.9 £10 % 5.42 £10% 5400 48.7 £10% 5.53 210 % Page: 9/11 This document shall not be reproduced, except in full or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyforthe purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO. t ce y >

SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.262.8.14.SATU.A 5500 48.6 £10 % 5.65 £10 % 5600 48.5 £10 % 5.77 £10% 5800 48.2 £10 % 6.00 £10 % 7.4 SAR MEASUREMENT RESULT WITH BODY LIQUID Software OPENSAR V4 Phantom SN 20/09 SAM71 Probe SN18/11 EPG122 Liquid Body Liquid Values: eps‘ : 54.2 sigma : 1.54 Distance between dipole center and liquid 10.0 mm Area scan resolution dx=8mm/dy=8mm Zoon Scan Resolution dx=8mm/dy=8m/dz=5mm Frequency 1900 MHz Input power 20 dBm Liquid Temperature 21 °C Lab Temperature 21 °C Lab Humidity 45 % Frequent NR 1 g SAR (W/ke/w) 10 g SAR (W/kg/w) measured measured 1900 43.33 (4.33) 21.59 (2.16) ie / . Sudcor htmsy 4 g* h |“ 70 €00— zanters = $00— gs $ M mm & 00— Eol sm fll C= ;327‘]0 2 a 6 8 10 122 |‘A 16 10 20 2? M 2 m ® 2m BID FOC KiBC Y iem! 2j Page: 10/11 This document shall not be reproduced, except in full or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyforthe purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO. t cy >

(/r A SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.262.8.14.SATU.A SATiMD 8 LIST OF EQUIPMENT Equipment Summary Sheet Equipment Manufacturer / Identification No. Current Next Calibration Description Model Calibration Date Date SAM Phantom Satimo SN—20/09—SAM71 yeao:ijf‘éz_d' Noise) Y;fif;gd No: se COMOSAR Test Bench| Version 3 NA f(:jf‘etz_d' hNgie) ;g'jfetzd No: te) Network Analyzer Rhode8Schwarz sN100132 022016 022019 Calipers Carrera CALIPER—1 122016 122019 Reference Probe Satimo EPG122 SN18A1 102018 102019 Multimeter Keithley 2000 1188656 122016 122019 Signal Generator Agilent E4438C my490705s81 122016 122019 mote xucom mice neearan nerorer Power Meter HP E4418A Usss2e1498 122016 122019 Power Sensor HP ECP—E26A uss7181460 122016 122019 Directional Coupler Narda 4216—20 o1386 tcegf‘rafigegsf’fegflfigf ;Z?Fafifng?egflfi;g’ Li?”n‘?fi'@téfnig? Control Company 11—661—9 arois 82019 Page: 11/11 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO. t ce y >

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 055503719 Report No.: LCS190923018AEB 5.6 S1D2450 Dipole Calibration Ceriticate (/(.\ SATIMO The microwave vision company_A SAR Reference Dipole Calibration Report Ref : ACR.287.8.14.SATU.A SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. 1F., XINGYUAN INDUSTRIAL PARK, TONGDA ROAD, BAO‘AN BLVD BAO‘AN DISTRICT, SHENZHEN, GUANGDONG, CHINA SATIMO COMOSAR REFERENCE DIPOLE FREQUENCY: 2450 MHZ SERIAL NO.: SN 07/14 DIP 2G450—306 Calibrated at SATIMO US 2105 Barrett Park Dr. — Kennesaw, GA 30144 i) w fAat//z T es Zrm~cS (accrepbirep) Crdtie® aiitrationcest szzcsos 10/01/2018 Summ ary. This document presents the methodand results from an accredited SAR reference dipole calibration performed in SATIMO USA using the COMOSAR test bench. All calibration results are traceable to national metrologyinstitutions. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 127 of 144

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 055503719 Report No.: LCS190923018AEB : SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR.287.8.14.SATU.A SATI MD Name Function Date Signature Prepared by: Jérome LUC Product Manager 10/14/2018 //%’ Checked by : Jérome LUC Product Manager 10/14/2018 //3/ Approved by: Kim RUTKOWSKI Quality Manager 10/14/2018 Jum Pautthowh? Customer Name Shenzhen LCS Distribution : Compliance Testing Laboratory Ltd. Issue Date Modifications A 10/14/2018 Initial release Page: 2/11 This document shall not be reproduced, except in full or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyforthe purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO. This report shall not be reproduced except in full, without the written approval of Shenthen LCS Compliance Testing Laboratory Ltd. Page 128 of 144

(( [ \ SAR REFERENCE DIPOLE CALIBRATION REPORT Ref: ACR287.8.14.SATU.A TABLE OF CONTENTS ) IMfOducHO®:—mmmeormmmnmenememrmmmmnareroemenrarerermmarnmenmmemymmonmmernmnm 4 B DCVIC@ URCCF TESE ... ... s cmemimecmmmmmmmnnmncrmensecirmmmecmnnemmntrenmrermmrocremnmmmsnteernnccnczcne 4 3 PFOUUGCE DeSCFIPLION ——.. vemmememmmmommenmmmenmmnmiereemmenenenmmmmeminmmmnrnememenisiimmmercer 4 3.1 General Information 4 #: MeASUROMeNENCHAIOU —:——+—msmemscommmrenecncerormemiermsnctisesmemseretemecmmetimmmemisrime $ 4.1 Return Loss Requirements 5 4.2 Mechanical Requirements 5 5 MEASUT@ME@Nt UNCETEANEY ... ... en eeemmeemeememeeeeeee n n en en en ernernenneernernerne en en enene. 5 5.1 Return Loss $ 5.2 Dimension Measurement § 5.3 Validation Measurement 5 6 CalibrAtiON MEASUT@MENE RESUIS .............2.nene e en en reeneeneemneeneen e 6 6.1 Return Loss and Impedance 6 6.2 Mechanical Dimensions 6 7 Validation measurement ... 7.1 Head Liquid Measurement 7 7.2 SAR Measurement Result With Head Liquid 7 7.3 Body Liquid Measurement 9 7.4 SAR Measurement Result With Body Liquid 9 $ 148E Of EGUIPMENE —mmmmmmmemmmcommmerrerorammmenararamparmeramerarmeycarormaa §1 Page: 3/11 This document shall not be reproduced, except in full or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyforthe purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO. t c y >

((( \ SAR REFERENCE DIPOLE CALIBRATION REPORT KiMenesi®AugAtOdt 1 INTRODUCTION This document contains a summary of the requirements set forth by the IEEE 1528, OET 65 Bulletin C and CEVIEC 62209 standards for reference dipoles used for SAR measurement system validations and the measurements that were performed to verify that the product complies with the fore mentioned standards. 2 DEVICE UNDER TEST Device Under Test Device Type COMOSAR 2450 MHz REFERENCE DIPOLE Manufacturer Satimo Model $1D2450 Serial Number SN 07/14 DIP 2G450—306 Product Condition (new / used) New A yearly calibration interval is recommended. 3 PRODUCT DESCRIPTION 3.1 GENERAL INFORMATION Satimo‘s COMOSAR Validation Dipoles are built in accordance to the IEEE 1528, OET 65 Bulletin C and CEIIEC 62209 standards. The product is designed for use with the COMOSAR test bench only. Figure 1 — Satimo COMOSAR Validation Dipole Page: 4/11 This document shall not be reproduced, except infull or in part, without the written approval ofSATIMO. The information contained herein is to be used onlyfor the purposefor which it is submitted and is not to be released in whole orpart without written approval ofSATIMO.


Document Created: 2019-11-04 18:22:18
Document Modified: 2019-11-04 18:22:18
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC