Test Report BTLE

FCC ID: O55463141

Test Report

Download: PDF
FCCID_2315020

FCC PART 15.247 TEST REPORT For SWAGTEK 8800NW 23rd Street, Miami, FL33172, USA FCC ID: O55463141 Report Type: Product Type: Original Report Mobile Phone Test Engineer: David Lee Report Number: RSZ140603006-00B Report Date: 2014-06-25 Jimmy Xiao Reviewed By: RF Engineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Note: This test report is prepared for the customer shown above and for the equipment described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp.

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B TABLE OF CONTENTS GENERAL INFORMATION .......................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................4 OBJECTIVE ...................................................................................................................................................................4 RELATED SUBMITTAL(S)/GRANT(S) .............................................................................................................................4 TEST METHODOLOGY ..................................................................................................................................................4 TEST FACILITY .............................................................................................................................................................5 SYSTEM TEST CONFIGURATION ..........................................................................................................................6 DESCRIPTION OF TEST CONFIGURATION ......................................................................................................................6 EUT EXERCISE SOFTWARE ..........................................................................................................................................6 SPECIAL ACCESSORIES .................................................................................................................................................6 EQUIPMENT MODIFICATIONS .......................................................................................................................................6 EXTERNAL I/O CABLE..................................................................................................................................................6 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................6 SUMMARY OF TEST RESULTS ...............................................................................................................................7 FCC§15.247 (i), §1.1307 (b) (1) &§2.1093 – RF EXPOSURE ........................................................................................8 APPLICABLE STANDARD ..............................................................................................................................................8 FCC §15.203 - ANTENNA REQUIREMENT.............................................................................................................9 APPLICABLE STANDARD ..............................................................................................................................................9 ANTENNA CONNECTOR CONSTRUCTION ......................................................................................................................9 FCC §15.207 (a) – AC LINE CONDUCTED EMISSIONS .....................................................................................10 APPLICABLE STANDARD ............................................................................................................................................10 MEASUREMENT UNCERTAINTY ..................................................................................................................................10 EUT SETUP ................................................................................................................................................................10 EMI TEST RECEIVER SETUP .......................................................................................................................................11 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................11 TEST PROCEDURE ......................................................................................................................................................11 CORRECTED FACTOR & MARGIN CALCULATION .......................................................................................................11 TEST RESULTS SUMMARY ..........................................................................................................................................12 TEST DATA ................................................................................................................................................................12 FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS.............................................................................15 APPLICABLE STANDARD ............................................................................................................................................15 MEASUREMENT UNCERTAINTY ..................................................................................................................................15 EUT SETUP ................................................................................................................................................................15 EMI TEST RECEIVER & SPECTRUM ANALYZER SETUP ..............................................................................................16 TEST PROCEDURE ......................................................................................................................................................16 CORRECTED AMPLITUDE & MARGIN CALCULATION .................................................................................................16 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................17 TEST RESULTS SUMMARY ..........................................................................................................................................17 TEST DATA ................................................................................................................................................................17 FCC §15.247(a) (2) – 6 dB EMISSION BANDWIDTH ............................................................................................22 APPLICABLE STANDARD ............................................................................................................................................22 TEST PROCEDURE ......................................................................................................................................................22 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................22 TEST DATA ................................................................................................................................................................22 FCC §15.247(b) (3) - MAXIMUM PEAK OUTPUT POWER ................................................................................25 FCC Part 15.247 Page 2 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B APPLICABLE STANDARD ............................................................................................................................................25 TEST PROCEDURE ......................................................................................................................................................25 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................25 TEST DATA ................................................................................................................................................................25 FCC §15.247(d) – 100 kHz BANDWIDTH OF FREQUENCY BAND EDGE .......................................................28 APPLICABLE STANDARD ............................................................................................................................................28 TEST PROCEDURE ......................................................................................................................................................28 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................28 TEST DATA ................................................................................................................................................................29 FCC §15.247(e) - POWER SPECTRAL DENSITY .................................................................................................31 APPLICABLE STANDARD ............................................................................................................................................31 TEST PROCEDURE ......................................................................................................................................................31 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................31 TEST DATA ................................................................................................................................................................31 PRODUCT SIMILARITY DECLARATION LETTER ..........................................................................................34 FCC Part 15.247 Page 3 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B GENERAL INFORMATION Product Description for Equipment under Test (EUT) The SWAGTEK’s product, model number: X3 (FCC ID: O55463141) or the "EUT" in this report was a mobile phone, which was measured approximately: 137.8 mm (L) x 67.7 mm (W) x 7.8 mm (H), rated with input voltage: DC 3.7 V rechargeable Li-ion battery or DC 5.0V from adapter. Adapter Information: Input: AC 100-240V, 50/60 Hz, 0.15 A Output: DC 5.0V, 700 mA Note: The model 47 is electrically identical with the same PCB layout and schematic with the model: X3 tested by BACL, the only difference is the model number for the purpose of market, the detailed information can be referred to the attached declaration letter that stated and guaranteed by the applicant. *All measurement and test data in this report was gathered from production sample serial number: 1406010 (Assigned by BACL, Shenzhen). The EUT supplied by the applicant was received on 2014-06-03. Objective This report is prepared on behalf of SWAGTEK in accordance with Part 2-Subpart J, Part 15- Subparts A, B and C of the Federal Communication Commissions rules. The tests were performed in order to determine compliance with FCC Part 15, Subpart C, and section 15.203, 15.205, 15.207, 15.209 and 15.247 rules. Related Submittal(s)/Grant(s) FCC Part 15B JBP, Part 15.247 DTS (Wifi), Part 15.247 DSS (BT 3.0) and Part 22H/24E PCE submissions with FCC ID: O55463141 Test Methodology All measurements contained in this report were conducted with ANSI C63.4-2009, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. All emissions measurement was performed and Bay Area Compliance Laboratories Corp. (Shenzhen). The radiated testing was performed at an antenna-to-EUT distance of 3 meters. Measurement uncertainty with radiated emission is 5.91 dB for 30MHz-1GHz, and 4.92 dB for above 1GHz, 1.95dB for conducted measurement. FCC Part 15.247 Page 4 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B Test Facility The Test site used by Bay Area Compliance Laboratories Corp. (Shenzhen) to collect test data is located on the 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China. Test site at Bay Area Compliance Laboratories Corp. (Shenzhen) has been fully described in reports submitted to the Federal Communication Commission (FCC). The details of these reports have been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on December 06, 2010. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4- 2009. The Federal Communications Commission has the reports on file and is listed under FCC Registration No.: 382179. The test site has been approved by the FCC for public use and is listed in the FCC Public Access Link (PAL) database. FCC Part 15.247 Page 5 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B SYSTEM TEST CONFIGURATION Description of Test Configuration The system was configured for testing in an engineer mode. EUT Exercise Software BT test with adb command. Special Accessories No special accessory. Equipment Modifications No modification was made to the EUT tested. External I/O Cable Cable Description Length (m) From Port To Un-shielding Detachable USB Cable 1.8 EUT Adapter Block Diagram of Test Setup For conducted emission Adapter LISN EUT 10cm Receptacle Earphone 1.0 Meter Non-Conductive Table 80 cm above Ground Plane 1.5 Meters FCC Part 15.247 Page 6 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B SUMMARY OF TEST RESULTS FCC Rules Description of Test Result §15.247 (i), §1.1307 (b) (1)& RF Exposure Compliance §2.1093 §15.203 Antenna Requirement Compliance §15.207 (a), AC Line Conducted Emissions Compliance §15.247(d) Spurious Emissions at Antenna Port Compliance §15.205, §15.209, Spurious Emissions Compliance §15.247(d) §15.247 (a)(2) 6 dB Emission Bandwidth Compliance §15.247(b)(3) Maximum Peak Output Power Compliance §15.247(d) 100 kHz Bandwidth of Frequency Band Edge Compliance §15.247(e) Power Spectral Density Compliance FCC Part 15.247 Page 7 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B FCC§15.247 (i), §1.1307 (b) (1) &§2.1093 – RF EXPOSURE Applicable Standard According to FCC §2.1093 and §1.1307(b) (1), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. The SAR data please refer to the SAR report, report No.: RSZ140603006-20. FCC Part 15.247 Page 8 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B FCC §15.203 - ANTENNA REQUIREMENT Applicable Standard According to § 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the user of a standard antenna jack or electrical connector is prohibited. The structure and application of the EUT were analyzed to determine compliance with section §15.203 of the rules. §15.203 state that the subject device must meet the following criteria: a. Antenna must be permanently attached to the unit. b. Antenna must use a unique type of connector to attach to the EUT. Unit must be professionally installed, and installer shall be responsible for verifying that the correct antenna is employed with the unit. Antenna Connector Construction The EUT has one internal antenna arrangement, which the antenna gain is -1.0dBi, fulfill the requirement of this section. Please refer to the internal photos. Result: Compliant. FCC Part 15.247 Page 9 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B FCC §15.207 (a) – AC LINE CONDUCTED EMISSIONS Applicable Standard FCC§15.207 Measurement Uncertainty Input quantities to be considered for conducted disturbance measurements maybe receiver reading, attenuation of the connection between LISN and receiver, LISN voltage division factor, LISN VDF frequency interpolation and receiver related input quantities, etc. Based on CISPR 16-4-2:2011, the expended combined standard uncertainty of conducted disturbance test at Bay Area Compliance Laboratories Corp. (Shenzhen) is shown as below. And the uncertainty will not be taken into consideration for the test data recorded in the report Port Expanded Measurement uncertainty AC Mains 3.26 dB (k=2, 95% level of confidence) CAT 3 3.70 dB (k=2, 95% level of confidence) CAT 5 3.86 dB (k=2, 95% level of confidence) CAT 6 4.64 dB (k=2, 95% level of confidence) EUT Setup The measurement procedure of EUT setup is according with per ANSI C63.4-2009. The related limit was specified in FCC Part 15.207 limit. The adapter was connected to a 120 VAC/60 Hz power source. FCC Part 15.247 Page 10 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B EMI Test Receiver Setup The EMI test receiver was set to investigate the spectrum from 150 kHz to 30 MHz. During the conducted emission test, the EMI test receiver was set with the following configurations: Frequency Range IF B/W 150 kHz – 30 MHz 9 kHz Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date Rohde & Schwarz EMI Test Receiver ESCS30 100176 2014-06-17 2015-06-17 3560.6650.12- Rohde & Schwarz LISN ENV216 2014-05-07 2015-05-07 101613-Yb Rohde & Schwarz Transient Limiter ESH3Z2 DE25985 2013-10-15 2014-10-15 Rohde & Schwarz CE Test software EMC 32 V8.53 - - * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to requirements, traceable to National Primary Standards and International System of Units (SI). Test Procedure Maximizing procedure was performed on the six (6) highest emissions of the EUT. All data was recorded in the Quasi-peak and average detection mode. Corrected Factor & Margin Calculation The Corrected factor is calculated by adding LISN VDF (Voltage Division Factor), Cable Loss and Transient Limiter Attenuation. The basic equation is as follows: Correction Factor = LISN VDF + Cable Loss + Transient Limiter Attenuation The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of 7 dB means the emission is 7 dB below the limit. The equation for margin calculation is as follows: Margin = Limit – Corrected Amplitude FCC Part 15.247 Page 11 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B Test Results Summary According to the recorded data in following table, the EUT complied with the FCC Part 15.207, the worst margin reading as below: 8.6 dB at 0.455190 MHz in the Line conducted mode Refer to CISPR16-4-2:2011 and CISPR 16-4-1:2009, the measured level complies with the limit if Lm + U(Lm) ≤ Llim + Ucispr In BACL., U(Lm) is less than Ucispr, if Lm is less than Llim, it implies that the EUT complies with the limit. Test Data Environmental Conditions Temperature: 27 ℃ Relative Humidity: 56 % ATM Pressure: 101.0 kPa The testing was performed by David Lee on 2014-06-24. FCC Part 15.247 Page 12 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B EUT operation mode: Charging & Transmitting AC 120 V, 60 Hz, Line: EMI Auto Test L 90 80 70 QP 60 AV Level in dBμ 50 40 30 20 10 0 150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M Frequency in Hz Corrected Correction Frequency Limit Margin Detector Amplitude Factor (MHz) (dBμV) (dB) (PK/Ave./QP) (dBμV) (dB) 0.455190 43.4 19.6 56.8 13.4 QP 0.455190 38.2 19.6 46.8 8.6 Ave. 0.534050 43.6 19.6 56.0 12.4 QP 0.534050 35.7 19.6 46.0 10.3 Ave. 0.671830 37.8 19.6 56.0 18.2 QP 0.671830 28.6 19.6 46.0 17.4 Ave. 0.726930 38.3 19.6 56.0 17.7 QP 0.726930 29.9 19.6 46.0 16.1 Ave. 1.297170 38.5 19.5 56.0 17.5 QP 1.297170 29.8 19.5 46.0 16.2 Ave. 1.432430 36.1 19.5 56.0 19.9 QP 1.432430 27.8 19.5 46.0 18.2 Ave. FCC Part 15.247 Page 13 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B AC 120V, 60 Hz, Neutral: EMI Auto Test N 90 80 70 QP 60 AV Level in dBμ 50 40 30 20 10 0 150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M Frequency in Hz Corrected Correction Frequency Limit Margin Detector Amplitude Factor (MHz) (dBμV) (dB) (PK/Ave./QP) (dBμV) (dB) 0.514350 44.2 19.7 56.0 11.8 QP 0.514350 34.2 19.7 46.0 11.8 Ave. 0.891170 38.5 19.5 56.0 17.5 QP 0.891170 28.4 19.5 46.0 17.6 Ave. 0.943950 40.8 19.5 56.0 15.2 QP 0.943950 29.0 19.5 46.0 17.0 Ave. 1.085470 38.9 19.5 56.0 17.1 QP 1.085470 29.4 19.5 46.0 16.6 Ave. 1.120930 38.5 19.5 56.0 17.5 QP 1.120930 28.7 19.5 46.0 17.3 Ave. 1.373210 39.2 19.5 56.0 16.8 QP 1.373210 29.1 19.5 46.0 16.9 Ave. Note: 1) Correction Factor =LISN VDF (Voltage Division Factor) + Cable Loss + Transient Limiter Attenuation The corrected factor has been input into the transducer of the test software. 2) Corrected Amplitude = Reading + Correction Factor 3) Margin = Limit – Corrected Amplitude FCC Part 15.247 Page 14 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS Applicable Standard FCC §15.247 (d); §15.209; §15.205; Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, antenna factor calibration, antenna directivity, antenna factor variation with height, antenna phase center variation, antenna factor frequency interpolation, measurement distance variation, site imperfections, mismatch (average), and system repeatability. Based on CISPR 16-4-2:2011, the expended combined standard uncertainty of radiation emissions at Bay Area Compliance Laboratories Corp. (Shenzhen) is 5.91 dB for 30MHz-1GHz, and 4.92 dB for above 1GHz. And this uncertainty will not be taken into consideration for the test data recorded in the report. EUT Setup The radiated emission tests were performed in the 3 meters test site, using the setup accordance with the ANSI C63.4-2009. The specification used was the FCC 15.209, and FCC 15.247 limits. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. FCC Part 15.247 Page 15 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B EMI Test Receiver & Spectrum Analyzer Setup The system was investigated from 30 MHz to 25 GHz. During the radiated emission test, the EMI test receiver & Spectrum Analyzer Setup were set with the following configurations: Frequency Range RBW Video B/W IF B/W Detector 30 MHz – 1000 MHz 100 kHz 300 kHz 120 kHz QP 1 MHz 3 MHz / PK Above 1 GHz 1 MHz 10 Hz / Ave. Test Procedure Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. Data was recorded in Quasi-peak detection mode for frequency range of 30 MHz-1GHz and peak and Average detection modes for frequencies above 1 GHz. Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Loss, and subtracting the Amplifier Gain from the Meter Reading. The basic equation is as follows: Corrected Amplitude = Meter Reading + Antenna Factor + Cable Loss - Amplifier Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of 7dB means the emission is 7dB below the limit. The equation for margin calculation is as follows: Margin = Limit – Corrected Amplitude FCC Part 15.247 Page 16 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date HP Amplifier HP8447E 1937A01046 2013-09-30 2014-09-30 Rohde & Schwarz EMI Test Receiver ESCI 101120 2013-11-12 2014-11-12 Sunol Sciences Broadband Antenna JB1 A040904-1 NCR NCR Mini Amplifier ZVA-183-S+ 5969001149 2014-04-03 2015-04-03 A.H. System Horn Antenna SAS-200/571 135 2012-02-11 2015-02-10 Rohde & Schwarz Signal Analyzer FSIQ26 8386001028 2013-11-12 2014-11-12 the electro- Horn Antenna 3116 9510-2270 2013-10-14 2016-10-13 Mechanics Co. ALN- DUCOMMUN Pre-amplifier 991373-01 2013-08-03 2014-08-03 22093530-01 R&S Auto test Software EMC32 V9.10 -- -- * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to requirements, traceable to National Primary Standards and International System of Units (SI). Test Results Summary According to the recorded data in following table, the EUT complied with the FCC Title 47, Part 15, Subpart C, section 15.205, 15.209 and 15.247, the worst margin reading as below: 12.55 dB at 9760.00 MHz in the Vertical polarization Refer to CISPR16-4-2:2011 and CISPR 16-4-1:2009, the measured level complies with the limit if Lm + U(Lm) ≤ Llim + Ucispr In BACL, U(Lm) is less than Ucispr, if Lm is less than Llim, it implies that the EUT complies with the limit. Test Data Environmental Conditions Temperature: 27 ℃ Relative Humidity: 56 % ATM Pressure: 101.0 kPa The testing was performed by David Lee on 2014-06-24. EUT operation mode: Transmitting FCC Part 15.247 Page 17 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B 30 MHz-25 GHz FCC Part Receiver Turn Rx Antenna Corrected Corrected Frequency 15.247/205/209 table Factor Amplitude (MHz) Reading Detector Degree Height Polar (dB) (dBμV/m) Limit Margin (dBμV) (PK/QP/Ave.) (m) (H/V) (dBμV/m) (dB) Low Channel (2402 MHz) 239.9 35.66 QP 78 1.9 V -15.3 20.36 46 25.64 2402.00 90.04 PK 289 2.0 H 5.48 95.52 / / 2402.00 79.94 Ave. 289 2.0 H 5.48 85.42 / / 2402.00 89.38 PK 139 1.9 V 5.48 94.86 / / 2402.00 78.09 Ave. 139 1.9 V 5.48 83.57 / / 2344.82 38.07 PK 270 1.8 V 5.48 43.55 74 30.45 2344.82 20.19 Ave. 270 1.8 V 5.48 25.67 54 28.33 2375.18 36.09 PK 166 2.3 H 5.48 41.57 74 32.43 2375.18 25.72 Ave. 166 2.3 H 5.48 31.20 54 22.80 2485.80 35.75 PK 320 1.9 H 7.21 42.96 74 31.04 2485.80 24.15 Ave. 320 1.9 H 7.21 31.36 54 22.64 4804.00 36.24 PK 162 1.5 V 12.44 48.68 74 25.32 4804.00 21.91 Ave. 162 1.5 V 12.44 34.35 54 19.65 7206.00 36.28 PK 217 1.9 H 17.06 53.34 74 20.66 7206.00 20.46 Ave. 217 1.9 H 17.06 37.52 54 16.48 9608.00 35.18 PK 255 2.4 H 19.28 54.46 74 19.54 9608.00 21.37 Ave. 255 2.4 H 19.28 40.65 54 13.35 Middle Channel (2440 MHz) 239.9 35.55 QP 138 1.4 V -15.3 20.25 46 25.75 2440.00 89.92 PK 65 1.6 H 6.13 96.05 / / 2440.00 79.29 Ave. 65 1.6 H 6.13 85.42 / / 2440.00 87.80 PK 246 1.3 V 6.13 93.93 / / 2440.00 78.04 Ave. 246 1.3 V 6.13 84.17 / / 2361.10 39.80 PK 308 1.2 V 5.48 45.28 74 28.72 2361.10 23.30 Ave. 308 1.2 V 5.48 28.78 54 25.22 2373.75 40.06 PK 338 1.5 H 5.48 45.54 74 28.46 2373.75 23.97 Ave. 338 1.5 H 5.48 29.45 54 24.55 2488.18 36.72 PK 8 2.2 H 7.21 43.93 74 30.07 2488.18 19.49 Ave. 8 2.2 H 7.21 26.70 54 27.30 4880.00 37.22 PK 126 2.4 H 12.4 49.62 74 24.38 4880.00 20.97 Ave. 126 2.4 H 12.4 33.37 54 20.63 7320.00 35.35 PK 326 1.4 H 16.49 51.84 74 22.16 7320.00 21.91 Ave. 326 1.4 H 16.49 38.40 54 15.60 9760.00 36.91 PK 335 1.1 V 19.4 56.31 74 17.69 9760.00 22.05 Ave. 335 1.1 V 19.4 41.45 54 12.55 FCC Part 15.247 Page 18 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B FCC Part Receiver Turn Rx Antenna Corrected Corrected Frequency 15.247/205/209 table Factor Amplitude (MHz) Reading Detector Degree Height Polar (dB) (dBμV/m) Limit Margin (dBμV) (PK/QP/Ave.) (m) (H/V) (dBμV/m) (dB) High Channel (2480 MHz) 239.9 36.56 QP 87 1.1 V -15.3 21.26 46 24.74 2480.00 89.28 PK 249 1.9 H 7.21 96.49 / / 2480.00 77.37 Ave. 249 1.9 H 7.21 84.58 / / 2480.00 86.94 PK 358 2.4 V 7.21 94.15 / / 2480.00 78.02 Ave. 358 2.4 V 7.21 85.23 / / 2369.37 40.47 PK 308 1.0 V 5.48 45.95 74 28.05 2369.37 24.98 Ave. 308 1.0 V 5.48 30.46 54 23.54 2387.36 45.38 PK 158 1.8 H 5.48 50.86 74 23.14 2387.36 30.85 Ave. 158 1.8 H 5.48 36.33 54 17.67 2488.31 38.14 PK 203 2.4 H 7.21 45.35 74 28.65 2488.31 23.94 Ave. 203 2.4 H 7.21 31.15 54 22.85 4960.00 37.04 PK 151 2.2 V 12.5 49.54 74 24.46 4960.00 23.33 Ave. 151 2.2 V 12.5 35.83 54 18.17 7440.00 34.91 PK 171 2.3 H 15.9 50.81 74 23.19 7440.00 21.19 Ave. 171 2.3 H 15.9 37.09 54 16.91 9920.00 35.65 PK 84 1.6 V 19.39 55.04 74 18.96 9920.00 20.70 Ave. 84 1.6 V 19.39 40.09 54 13.91 FCC Part 15.247 Page 19 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B Conducted Spurious Emissions at Antenna Port: Delta Peak to Frequency Limit Channel Band Emission Result (MHz) (dB) (dB) Low 2402 24.69 20 Pass Middle 2440 24.44 20 Pass High 2480 24.26 20 Pass Low Channel Delta 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl -24.69 dB VBW 300 kHz 23.5 dBm 2.40353006 GHz SWT 6.4 s Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 5.48 dBm A 2.38188377 GHz 1 [T1] -24.69 dB 10 Fundamental 1 2.40353006 GHz 0 -10 1MAX 1MA 1 -20 -30 -40 -50 -60 -70 -76.5 Start 30 MHz 2.497 GHz/ Stop 25 GHz Date: 24.JUN.2014 01:59:18 FCC Part 15.247 Page 20 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B Middle Channel Delta 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl -24.44 dB VBW 300 kHz 23.5 dBm 2.45357014 GHz SWT 6.4 s Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 4.70 dBm A 2.43192385 GHz 1 [T1] -24.44 dB 10 Fundamental 1 2.45357014 GHz 0 -10 1MAX 1MA 1 -20 -30 -40 -50 -60 -70 -76.5 Start 30 MHz 2.497 GHz/ Stop 25 GHz Date: 24.JUN.2014 02:00:11 High Channel Delta 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl -24.26 dB VBW 300 kHz 23.5 dBm 2.45357014 GHz SWT 6.4 s Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 3.72 dBm A 2.48196393 GHz 1 [T1] -24.26 dB 10 2.45357014 GHz 1 Fundamental 0 -10 1MAX 1MA 1 -20 -30 -40 -50 -60 -70 -76.5 Start 30 MHz 2.497 GHz/ Stop 25 GHz Date: 24.JUN.2014 02:00:50 FCC Part 15.247 Page 21 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B FCC §15.247(a) (2) – 6 dB EMISSION BANDWIDTH Applicable Standard Systems using digital modulation techniques may operate in the 902–928 MHz, 2400–2483.5 MHz, and 5725–5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. Test Procedure According to KDB 558074 D01 DTS Meas Guidance v03r01 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. Position the EUT without connection to measurement instrument. Turn on the EUT and connect it to measurement instrument. Then set it to any one convenient frequency within its operating range. Set a reference level on the measuring instrument equal to the highest peak value. 3. Measure the frequency difference of two frequencies that were attenuated 6 dB from the reference level. Record the frequency difference as the emission bandwidth. 4. Repeat above procedures until all frequencies measured were complete. Signal Analyzer EUT Attenuator Test Equipment List and Details Calibration Calibration Manufacturer Description Model Serial Number Date Due Date Rohde & Schwarz Signal Analyzer FSIQ26 837405/023 2014-05-31 2015-05-31 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to requirements, traceable to National Primary Standards and International System of Units (SI). Test Data Environmental Conditions Temperature: 27 ℃ Relative Humidity: 56 % ATM Pressure: 101.0 kPa The testing was performed by David Lee on 2014-06-24. EUT operation mode: Transmitting Test Result: Compliance FCC Part 15.247 Page 22 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B Please refer to the following tables and plots. Channel 6 dB Emission Limit Channel Frequency Bandwidth (kHz) (MHz) (kHz) Low 2402 691.4 ≥500 Middle 2440 691.4 ≥500 High 2480 691.4 ≥500 Low Channel Marker 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl 1.31 dBm VBW 300 kHz 23.5 dBm 2.40163026 GHz SWT 5 ms Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 1.31 dBm A 2.40163026 GHz OPB 1.10621242 MHz 10 D1 7.41 dBm T1 [T1] -6.44 dBm 1 1 2.40144389 GHz D2 1.41 dBm 0 T2 [T1] -6.16 dBm T1 T2 2.40255010 GHz 1 [T1] -0.21 dB -10 1MAX 1MA 691.38276553 kHz -20 -30 -40 -50 -60 -70 -76.5 Center 2.402 GHz 300 kHz/ Span 3 MHz Date: 24.JUN.2014 00:32:53 FCC Part 15.247 Page 23 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B Middle Channel Marker 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl 1.08 dBm VBW 300 kHz 23.5 dBm 2.43962425 GHz SWT 5 ms Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 1.08 dBm A 2.43962425 GHz OPB 1.10621242 MHz 10 D1 7.47 dBm T1 [T1] -6.53 dBm 1 1 2.43944389 GHz D2 1.47 dBm 0 T2 [T1] -6.01 dBm T1 T2 2.44055010 GHz 1 [T1] 0.67 dB -10 1MAX 1MA 691.38276553 kHz -20 -30 -40 -50 -60 -70 -76.5 Center 2.44 GHz 300 kHz/ Span 3 MHz Date: 24.JUN.2014 00:30:41 High Channel Marker 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl 1.28 dBm VBW 300 kHz 23.5 dBm 2.47963026 GHz SWT 5 ms Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 1.28 dBm A 2.47963026 GHz OPB 1.10621242 MHz 10 D1 7.23 dBm T1 [T1] -6.88 dBm 1 1 2.47944389 GHz D2 1.23 dBm T2 [T1] -6.21 dBm 0 T1 T2 2.48055010 GHz 1 [T1] -0.18 dB -10 1MAX 1MA 691.38276553 kHz -20 -30 -40 -50 -60 -70 -76.5 Center 2.48 GHz 300 kHz/ Span 3 MHz Date: 24.JUN.2014 00:24:09 FCC Part 15.247 Page 24 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B FCC §15.247(b) (3) - MAXIMUM PEAK OUTPUT POWER Applicable Standard According to §15.247(b) (3), for systems using digital modulation in the 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz bands: 1 Watt. As an alternative to a peak power measurement, compliance with the one Watt limit can be based on a measurement of the maximum conducted output power. Maximum Conducted Output Power is defined as the total transmit power delivered to all antennas and antenna elements averaged across all symbols in the signaling alphabet when the transmitter is operating at its maximum power control level. Power must be summed across all antennas and antenna elements. The average must not include any time intervals during which the transmitter is off or is transmitting at a reduced power level. If multiple modes of operation are possible (e.g., alternative modulation methods), the maximum conducted output power is the highest total transmit power occurring in any mode. Test Procedure According to KDB 558074 D01 DTS Meas Guidance v03r01 1. Place the EUT on a bench and set it in transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to a test equipment. 3. Add a correction factor to the display. EUT Signal Analyzer Attenuator Test Equipment List and Details Calibration Calibration Manufacturer Description Model Serial Number Date Due Date Rohde & Schwarz Signal Analyzer FSIQ26 837405/023 2014-05-31 2015-05-31 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to requirements, traceable to National Primary Standards and International System of Units (SI). Test Data Environmental Conditions Temperature: 27 ℃ Relative Humidity: 56 % ATM Pressure: 101.0 kPa The testing was performed by David Lee on 2014-06-24. FCC Part 15.247 Page 25 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B EUT operation mode: Transmitting Conducted Frequency Limit Channel Output Power Result (MHz) (dBm) (dBm) Low 2402 8.28 30 Pass Middle 2440 9.00 30 Pass High 2480 8.47 30 Pass RF Output Power, Low Channel Marker 1 [T1] RBW 1 MHz RF Att 30 dB Ref Lvl 8.28 dBm VBW 3 MHz 23.5 dBm 2.40176453 GHz SWT 5 ms Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 8.28 dBm A 2.40176453 GHz 10 1 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76.5 Center 2.402 GHz 500 kHz/ Span 5 MHz Date: 24.JUN.2014 00:55:33 FCC Part 15.247 Page 26 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B RF Output Power, Middle Channel Marker 1 [T1] RBW 1 MHz RF Att 30 dB Ref Lvl 9.00 dBm VBW 3 MHz 23.5 dBm 2.43973447 GHz SWT 5 ms Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 9.00 dBm A 2.43973447 GHz 1 10 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76.5 Center 2.44 GHz 500 kHz/ Span 5 MHz Date: 24.JUN.2014 00:56:37 RF Output Power, High Channel Marker 1 [T1] RBW 1 MHz RF Att 30 dB Ref Lvl 8.47 dBm VBW 3 MHz 23.5 dBm 2.47976453 GHz SWT 5 ms Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 8.47 dBm A 2.47976453 GHz 10 1 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76.5 Center 2.48 GHz 500 kHz/ Span 5 MHz Date: 24.JUN.2014 00:57:07 FCC Part 15.247 Page 27 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B FCC §15.247(d) – 100 kHz BANDWIDTH OF FREQUENCY BAND EDGE Applicable Standard In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) (see §15.205(c)). Test Procedure According to KDB 558074 D01 DTS Meas Guidance v03r01 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. Position the EUT without connection to measurement instrument. Turn on the EUT and connect its antenna terminal to measurement instrument via a low loss cable. Then set it to any one measured frequency within its operating range, and make sure the instrument is operated in its linear range. 3. Set RBW to 100 kHz and VBW of spectrum analyzer to 300 kHz with a convenient frequency span including 100 kHz bandwidth from band edge. 4. Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the graph with marking the highest point and edge frequency. 5. Repeat above procedures until all measured frequencies were complete. Signal Analyzer EUT Attenuator Test Equipment List and Details Calibration Calibration Manufacturer Description Model Serial Number Date Due Date Rohde & Schwarz Signal Analyzer FSIQ26 837405/023 2014-05-31 2015-05-31 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to requirements, traceable to National Primary Standards and International System of Units (SI). FCC Part 15.247 Page 28 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B Test Data Environmental Conditions Temperature: 27 ℃ Relative Humidity: 56 % ATM Pressure: 101.0 kPa The testing was performed by David Lee on 2014-06-24. EUT operation mode: Transmitting Test Result: Compliance. Please refer to following table and plots. Delta Peak to Band Emission Limit Band edges (dB) (dB) Left Band 52.71 20 Right Band 53.39 20 FCC Part 15.247 Page 29 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B Band Edge, Left Side Delta 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl -52.71 dB VBW 300 kHz 23.5 dBm -3.50701403 MHz SWT 5 ms Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 7.24 dBm A 2.40201403 GHz 1 [T1] -52.71 dB 10 1 -3.50701403 MHz 0 -10 1MAX 1MA -20 -30 -40 1 -50 -60 -70 -76.5 Center 2.4 GHz 1 MHz/ Span 10 MHz Date: 24.JUN.2014 01:51:53 Band Edge, Right Side Delta 1 [T1] RBW 100 kHz RF Att 30 dB Ref Lvl -53.39 dB VBW 300 kHz 23.5 dBm 3.54709419 MHz SWT 5 ms Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 6.56 dBm A 2.48002305 GHz 1 [T1] -53.39 dB 10 1 3.54709419 MHz 0 -10 1MAX 1MA -20 -30 -40 1 -50 -60 -70 -76.5 Center 2.4835 GHz 1 MHz/ Span 10 MHz Date: 24.JUN.2014 01:52:57 FCC Part 15.247 Page 30 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B FCC §15.247(e) - POWER SPECTRAL DENSITY Applicable Standard For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. This power spectral density shall be determined in accordance with the provisions of paragraph (b) of this section. The same method of determining the conducted output power shall be used to determine the power spectral density. Test Procedure According to KDB 558074 D01 DTS Meas Guidance v03r01 1. Set analy center frequency to DTS channel center frequency. 2. Set the span to 1.5 times the DTS channel bandwidth. 3. Set the RBW ≥ 3 kHz. 4. Set the VBW ≥ 3 x RBW. 5. Detector = peak. 6. Sweep time = auto couple. 7. Trace mode = max hold. 8. Allow trace to fully stabilize. 9. Use the peak marker function to determine the maximum power level. 10. If measurement value exceeds limit, reduce RBW (no less than 3 kHz) and repeat. EUT Attenuator Signal Analyzer Test Equipment List and Details Calibration Calibration Manufacturer Description Model Serial Number Date Due Date Rohde & Schwarz Signal Analyzer FSIQ26 837405/023 2014-05-31 2015-05-31 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to requirements, traceable to National Primary Standards and International System of Units (SI). Test Data Environmental Conditions Temperature: 27 ℃ Relative Humidity: 56 % ATM Pressure: 101.0 kPa The testing was performed by David Lee on 2014-06-24. FCC Part 15.247 Page 31 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B EUT operation mode: Transmitting Test Result: Pass. Please refer to following table and plots. Power spectral Frequency Limit Channel density (MHz) (dBm/3kHz) (dBm/3kHz) Low 2402 1.79 ≤8 Middle 2440 1.80 ≤8 High 2480 1.30 ≤8 Low Channel Marker 1 [T1] RBW 3 kHz RF Att 30 dB Ref Lvl 1.79 dBm VBW 10 kHz 23.5 dBm 2.40225145 GHz SWT 300 ms Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 1.79 dBm A 2.40225145 GHz 10 1 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76.5 Center 2.402 GHz 105 kHz/ Span 1.05 MHz Date: 24.JUN.2014 01:05:31 FCC Part 15.247 Page 32 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B Middle Channel Marker 1 [T1] RBW 3 kHz RF Att 30 dB Ref Lvl 1.80 dBm VBW 10 kHz 23.5 dBm 2.44025356 GHz SWT 300 ms Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 1.80 dBm A 2.44025356 GHz 10 1 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76.5 Center 2.44 GHz 105 kHz/ Span 1.05 MHz Date: 24.JUN.2014 01:04:41 High Channel Marker 1 [T1] RBW 3 kHz RF Att 30 dB Ref Lvl 1.30 dBm VBW 10 kHz 23.5 dBm 2.48025566 GHz SWT 300 ms Unit dBm 23.5 20 3.5 dB Offset 1 [T1] 1.30 dBm A 2.48025566 GHz 10 1 0 -10 1MAX 1MA -20 -30 -40 -50 -60 -70 -76.5 Center 2.48 GHz 105 kHz/ Span 1.05 MHz Date: 24.JUN.2014 01:01:49 FCC Part 15.247 Page 33 of 34

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ140603006-00B PRODUCT SIMILARITY DECLARATION LETTER ***** END OF REPORT ***** FCC Part 15.247 Page 34 of 34


Document Created: 2018-08-01 19:31:51
Document Modified: 2018-08-01 19:31:51
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC