User_Manual

FCC ID: O5541SKN1

Users Manual

Download: PDF
FCCID_4418877

Smart Ring ORIGINALITY DESIGN SMART - AND BEAUTIFUL QUICK GUIDE

Functions 功能介绍 Remote wake-up The doorbell will be in a sleep mode to save power; you can have a preview in App and have a remote wake-up to monitor after 3-4 Seconds. Full-duplex audio When the visitor push the doorbell button, you will get a call. You can see and hear the vistor in your App from the doorbell if you answer. PIR When the doorbell detects someone stopping by, it sends an alarm message to your cell phone. Low battery alarm You can set a low-battery alarm threshold on your phone App. The threshold is set to a minimum of 10% and a maximum of 50%. When the battery power of the doorbell is lower than the set threshold, the App will have a reminder. Battery Lock After battery box connected ,it will be locked immediately. User have to unlock the battery box in the App setting page to if want to take out the battery box,only 30 seconds allowed. Shared device The doorbell device can be shared with friends, and friends can also preview online. There is no limit to the number of sharing devices, but only 6 accounts are supported for online preview at the same time. 1

What's in the box Consult the checklist below for all components. Smart Ring Power converter Mylar Battery box Power adapter USB cable Ax4 Bx4 Cx2 Dx1 Pin Screws(4 kinds) I/M Wire nuts Adhesive table 2

Microphone Status light Doorbell button Speaker Reset 1 SD card slot External power port Back of doorbell Description Power Port DC 5V±10%，use the screws to fix the power converter Doorbell button Press the button to activate the doorbell Status light Red light solids on: the camera network is abnormal Red light blinking: awaiting WiFi connection, or currently connecting (faster blinking) Blue light solids on: camera running correctly Microphone Captures sound for your video SD card slot Supports local SD Card storage (Max.128G) Reset1 Press and hold on for 5 seconds with pin to reset the doorbell (unable to unbind the bell from account) 3

Reset 2 Charging indicator Mini USB Bayonet lock Description Mini USB DC5V±10%,USB power supply Charging indicator Red indicator solids on: battery is charging Blue indicator solids on: finishing charging Reset 2 Tap reset button for 5 seconds to factory reset (it will not unbind the device) Bayonet lock Lock the battery box through bayonet lock Battery capacity 6000mAh (Two 18650 lithium-ion batteries) 4

Connect Download Smart Life is available for both iOS and Android OS. Rearch the name 'Smart Life'in App Store or Android Market, or scan the QR-Code to download the App. ·Support IOS Android Dowoload App(IOS&android) Set up router This device only supports 2.4GHz frequency band router, does not support 5GHz frequency band router, please set the relevant parameters of the router before WiFi configuration, WiFi passwords do not include special characters such as ~!@#$%^&*(). When the device is configured in WiFi, the mobile phone and device are as close as to the router, which can speed up the configuration of the device. Please keep network available 4

Registration process Step 1 Open the Smart Life App, click "Register", read the "Privacy Policy" and click "Agree" . Step 2 input a legal and valid Mobile number or Email address and click "Continue". Input Verification Code, then log in the app. 5

QR Code Configuration Getting started 1. Please follow the instructions and make sure the password is inputed correctly. 2. One device can only be added with one App account, if the device has been added with another account already, then it can't be added to any another account again. 3.The device will be unbind from previous account after been deleted from App. Further ,the device will be resetted automattically once from blue light to red light. Process Step 1 Open the Smart Life App, click "+" or "Add Device". Then select "All" on the "Select Device Type" page. Step 2 Select "Security Camera". Power the device on and make sure the indicator is flashing quickly or a prompt tone is heard. 7

Step 3 Input WiFi password and click "Confirm", scan the QR Code with a device. (You can change the network connection) About 20cm 8

Step 4 Click "I heard the beep" when the device comes out "dong dong dong". And you can complete the configuration about 30s. Step 5 The device is added, and the device nickname can also be changed in this interface. Notice：After the device configured successfully, it will be automatically locked.Motor in the battery box will make a sound.Click "Click to Unlock the Battery"first before unplug the battery. 9

FAQ Q: In the network process, the process bar is always not 100%, add failure? A: This camera only supports 2.4GHz WiFi router, please make sure you are using a 2.4GHz WiFi router.And confirm the WiFi password again. Q: Repeated additions are failures? A: After adding a failure, it is recommended to restart the device or power off, and then try to add again. Q: The device cannot be previewed properly? A: Check whether the network is normal, you can place the camera close to the router, and if not, it is recommended to reset the device and add it again. Q: How to cut the camera network to another router? A: First remove and reset the device on the App and then configure the device again by the App. Q: Why I can't get the notifications with my cell phone App? A: Please confirm that the App has been running on the phone, and the relevant reminder function has been opened;Message notification and authority confirmation in the mobile phone system have been opened. Q: Why doesn't the device identify the SD card? A: It is recommended to plug in SD card after power cut. Confirm whether the SD card is normally available and the format is FAT32. And the TF card can't be identified when the internet environment is not good. 10

Unlock Step 1 Click "...", enter the "Setting" page and click "Basic Feature Settings". Step 2 Enter the "Basic Feature Settings" setting page and click "Unlock the Battery" to unlock it automatically. When the motor is finished, the battery box can be pulled out. 12

Install 安装 Installation of Power supply mode Warning：Don’t fall down during using Mylar output- 8~24 cable V AC input- cable Red lead Black lead Step 1 Each input-cable (AC Step 2 Remove the bottom cover and bracket of the 8~24V) connect to the wires doorbell host and lead the output terminal.Connect which come out of the wall. to the power interface on the back of the doorbell host.Note: red lead connects the power "+", black connects the power "-". Step 3 Remove the double-sided adhesive Step 4 Use the marker to draw the on the back of the mylar sheet.Cover the positions of the 4 screw holes on t position of the power interface on the back he wall surface to be installed. of the doorbell host. 13

Step 5 Screw 4 expansion screws into the Step 6 Fix the mounting bracket to newly marked position. the wall. Step 7 Install the bottom door of the doorbell Step 8 Pull the power cable from the main unit and fix it with screws. center hole of the bracket and slowly insert the doorbell into the door as shown in the above figure (be careful not to catch your finger). 14

Install the device in battery-powered mode Step 1 Remove the doorbell bottom Step 2 Use the marker to draw 4 screw cover and bracket as shown in the holes on the surface of the wall to be figure installed Step 3 Screw 4 expansion screws into the Step 4 Fix the mounting bracket to newly marked position the wall 15

Step 5 Snap the doorbell into the bracket Step 6 Align the battery box with the bayonet lock, and push the battery box into doorbell. 16

FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.


Document Created: 2019-08-14 18:50:55
Document Modified: 2019-08-14 18:50:55
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC