Installation Manual

FCC ID: O34-I7770BASE

Users Manual

Download: PDF
FCCID_561658

3.5. Connections: Ensure that the paper is protruding from UNDERNEATH Recommended brands: Turn the i7780 base off when connecting peripherals. the roll: KANZAN .................... KF50 JUJO....................AF50KS-E KOEHLER..........KT55HS01 MITSUBISHI..............P6402 The power supply must be connected last, only after all Thermal paper should NOT be exposed to vinyl, plastics, adhesives, the other connections are made. shrink-wraps, wet-toner copies or certain carbon papers, office light UV light, high humidity and temperature (above 65%, 25°C or 77°F) for long periods of time. 8. If you experience problems: Call one of the customer service centers listed below: In Canada: In the USA: VERSATILE BASE TotalCARE Ingenico Inc. 4. Close the cover, press it until it snaps. Press the “Paper 6520 Gottardo Court TotalCARE feed” key to verify that paper feeds properly. Mississauga, Ontario 1003 Mansell Road L5T 2A2 Atlanta, GA 30076 5. Normal Operation: 1-888-900-8221 (905-795-8221) 1-800-435-3014 (770-594-6000) US Federal Communications Commission (FCC) Warnings: Depending of the application installed in the terminals, the This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of icons indicating battery charge level, Bluetooth signal the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency RADIO BASE strength and terminal docking status can be displayed. energy and, if not installed and used in accordance with the installation guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case To extend the battery life, the i7780 hand held goes into a the user will be required to correct the interference at his own expense. Maximum cable length is 2.5m. stand-by mode when it is not on its base. To quickly power Warning: Changes or modifications not expressly approved by Ingenico could void the user’s authority to operate the • ETHERNET CONNECTION (versatile base only) on the hand held: equipment. Turn off the versatile base and connect the Ethernet • Press the green <ENTER> key, or Canadian Department of Communications (DOC) Warnings: This digital apparatus does not exceed the Class B limits for radio noise emissions from the digital apparatus as set out cable (supplied with the terminal) to the port on the • Place the hand held briefly on the base. in the radio interference regulations of the Canadian Department of Communications. Ethernet Plug-It module. Plug the other end of the cable RF Exposure Warning: into the hub or router. 6. Cleaning procedure: To comply with RF exposure requirements the base unit must be installed and operated with a separation distance of 20 cm or more between the device and all person's body (excluding extremities of hands, wrist and feet). The terminal unit • DIAL LINE CONNECTION • The i7780 must be off for all cleaning operations. has been tested and meets RF exposure guidelines for hand held operation pursuant to FCC OET Bulletin 65 Supplement C ed. 01-01, IEEE 1528/D1.2 (2003) and Industry Canada RSS-102 (1999). The base and terminal units Plug the one end of a telephone cable (supplied with the • Do not clean the i7780 with water but with a dry or only must not be co-located or operated in conjunction with any other antenna or transmitter. For body worn operation, this device has been tested and meets FCC RF exposure guidelines when used with accessories that contain no metal and that position the device a minimum of 10 mm from the body. Use of other terminal) into the port, and connect the other end of the slightly damp cloth. accessories may not ensure compliance with FCC RF exposure guidelines. cable to a wall telephone jack. • Do not use solvent, detergent or abrasive products. ACTA Revision Part 68 • PHONE CONNECTION (radio base only) • If the terminal has battery recharging or communication This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachments (ACTA). On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: INBMM01Bi7780. If requested, this number must be provided to the telephone Plug one end of a telephone cable into the radio base port problems, clean the golden contact under the terminal company. , and plug the other end of the cable in the phone. with a damp cloth. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. • PERIPHERAL/HOST CONNECTION • Do not scratch or scrape the surface of the contacts. The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5). To be certain of the number of devices that Unplug the i7780 base. Connect the serial cable to the 7. Technical specifications: may be connected to a line, as determined by the total RENs, contact the local telephone company. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the base port marked COM2 or COM1/3. Plug the other end equipment until the problem is resolved. The i7780 system uses Bluetooth technology: Ingenico 7780 If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this I7780 of the serial cable to the device (PC, check reader etc.). does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your For detailed instructions, ask the equipment supplier. Type...........................20 dBm hopping frequency telephone company or a qualified installer. • POWER CONNECTION Bandwidth .................ISM 2.45 GHz Industry Canada Warning: NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is Plug the power adapter radial jack into the i7780 base Emitting power ..........≤ 100mW (20dBm) Installation Guide confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. port marked . The green light on the front right Range.........................≈ 200 meters (open field) It does not imply that Industry Canada approved the equipment. NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is <0.1>. The REN assigned to each hand side of the base indicates the power is on. The power supply: terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement Attach the cable securing plate and fix it with a screw. • INPUT ................AC 120V 60Hz that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five. NOTICE: To prevent radio interference to the licensed service, this device is intended to be operated indoors and away • OUTPUT . DC 18V 0.9A 16.2VA from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Thermal Paper Specification: • Single ply thermal sensitive – POS or facsimile grade. 3.6. Changing the printer paper: • Basis Weight: (lb/rm 17 ins. X 22 ins. - 500) --- 14.5 ± 5% Ingenico Inc. When the coloured stripe on the paper appears, replace (GSM) --- 55 ± 5% 1003 Mansell Road, Atlanta, GA 30076 the paper: • Caliper ............................ 2.4 ± 0.2 Mils or 60 ± 5 Microns Tel: (770) 594 – 6000 Fax: (770) 594 – 6003 1. Remove the i7780 from the base and wait till it turns • Brightness........................................................... Min. 85% www.ingenico-us.com off, do not touch the printer parts, they can be very • Smoothness (Bekk Minimum) ....................................300 s hot. Be aware of the sharp paper cutter. Ingenico Canada Ltd. • Roll Width ................... 2.28 ± 0.040 in (58 mm ± 1.0 mm) 2. Push the button on the paper compartment cover 79 Torbarrie Road, Toronto, Ontario, Canada, M3L 1G5 • Roll Diameter .......................... 1.97 in (50 mm) maximum toward the back and lift the cover. Tel: (416) 245 – 6700 Fax: (416) 245 – 6701 • Roll Core ID ............................. 0.500 in (13 mm) nominal DIV750026A 3. Remove the empty paper roll and insert the new roll. www.ingenico-ca.com • Roll Core OD............................ 0.625 in (16 mm) nominal

1. Ingenico 7780 description: The card has to be swiped at uniform speed and pressure, 8. The Ethernet cable (optional, with Ethernet module only). Always charge the battery at the room temperature. ensuring that the card remains in contact with the bottom of 9. The cable securing plate and a screw (optional, with the Charge the battery for 3 hours when it is used the first time. The i7780 is a portable (Bluetooth technology) point of the track throughout the entire swipe action. base only). Full charging time after the first time is 2 hours. A new sale electronic payment terminal designed to process 1.4. Smart Card Reader: 10. The holster (optional). battery will benefit from an initial "conditioning". The first 3 debit, credit and smart card purchases. It is highly Insert the smart card horizontally into the slot on the front of 11. This installation guide. times the battery is used, allow the battery to fully discharge secured, EMV level 1and 2 certified. the i7780, the microchip facing up, and leave it in the reader and then charge it to its full capacity. The i7780 communicates with the acquirer through its throughout the transaction. 3. Installation procedure: base via the telephone and/or Ethernet network. The The i7780 has EMV level 1&2 approvals and complies Place the i7780 base on a clear, flat surface near an electrical 3.2. Installing the Battery: hand-held terminal and the base communicate through Leave the i7780 handheld terminal off its base and wait until with the ISO 7816, Sync and Async T=1 & T=0. and telephone sockets. The ideal location is in the center of the Bluetooth link, or via direct contact. A network can it turns itself off before handling the battery pack. 1.5. Printer: the zone to be covered with a large open area around. The be set up, with one base managing up to 7 terminals at the Hold the battery with the connectors facing downwards, do The i7780 integrates a quiet, high speed, “easy-load” style antenna is inside, on the left side of the base. same time. Various peripherals can be connected to the not touch the contacts on the battery or the i7780. thermal printer with graphics capability. The i7780 hand held and the base must be protected from base through its RS-232 ports. 1.6. Battery: high temperature, vibrations, dust, dampness and Paper electromagnetic radiation (computer screen, microwave Navigation keys Compartment Rechargeable and easily replaceable Ni-MH or Li-Ion battery pack. oven, anti-theft barrier etc.). Equipment such as cordless and cellular phones can emit harmonics that could disturb the Magnetic 1.7. SAM Connectors: terminal at 2.45 GHz. Stripe Card Three SAM card connectors are located on the bottom of the Do not place the base near a great vertical metal plane (doors Reader i7780. The SAM (Secure Access Module) supports Paper of refrigerator, large home appliances, vending machines). smart card chips necessary for applications such as Ensure the base or the terminal is more than 3 m (around 10 Feed Key CANCEL loyalty. feet) from any microwave oven in use. Key 1.8. The Base Do not place the hand held terminal on a metal surface. Insert the two plastic teeth in the gaps on the i7780 case, The i7780 communicates with its base via Bluetooth radio Do not put your hand under the printer during place the battery in the cavity and press the handle until a CORR Key click is heard. link, or through the contacts (connect mode) which is useful communication, as the range is greatly reduced. when loading large amounts of data, or when a Bluetooth If there are several radio bases installed, position them at Smart Card ENTER Key link is unavailable. 3.3. SAM Installation: least 2 meters (around 6.5 feet) from each other. Wait till the i7780 turns off and remove its battery (do not Reader The i7780 works with either radio base or versatile base. The Green Power Ensure that the terminal is seated securely on the base. touch the contacts on the battery or the i7780). Unlock the versatile base has a Plug-It slot to add a Plug-It module with Indicator Light SAM connector by sliding the metallic latch in the direction Base Contacts additional communication port. Operating temperature ................................+5°C to +40°C of the OPEN arrow. Lift the SAM cover upward and insert The base station recharges the battery pack and includes the Humidity ........................ 20% to 90% without condensation the chip as shown on the picture below. Swing the cover 1.1. Display: following communication ports: Storage temperature ....................................-10°C to +60°C down and slide the latch into locked position (the LOCK A 4 line x 16 character LCD graphic display, with a - COM2 and COM1/3: Two RS-232 serial communication links for customer 3.1. Battery Set up and Charging: arrow). Put the battery back in the i7780 handheld. back light. applications download and for the communication with The i7780 is supplied with a removable rechargeable NiMH 1.2. Keypad: external peripherals (speed 300 to 115200 bps). The or Li-Ion battery. Only use the battery pack supplied with 18 keys, with a back light. The special function keys are: COM1/3 provides power for external devices. your terminal. • Programmable function keys <F1>, <F2> and <F3> - DIAL LINE port: i7780 battery is built with circuitry for intelligent battery for navigation and access to various i7780 functions A V34 / 33600 bps (asynch. and synchr.) modem that management. To charge the battery, place the handheld on and the system and application menus. supports fast connect and busy line detection. the base (the base must be powered up). • Paper Feed key is used for a printer paper feed (20mm) - TELEPHONE port (on radio base only): Ensure that the terminal is seated securely on the base. The green <ENTER> key confirms the data entered or The telephone port allows sharing of the telephone line with Use the power adapter supplied with the i7780. Many displayed. It also powers on the i7780. other devices such as a fax machine or telephone. adapters can appear similar and will plug into the i7780 base • The red <CAN> key cancels the current function and - ETHERNET port (on versatile base only): but will not work properly causing erratic behavior, poor 3.4. Changing The Plug-It Module: returns the terminal to the idle state. It also powers off The Ethernet port allows the i7780 to connect to a local charging or even damage to the unit. 1. Turn off the versatile base the i7780 if it is not docked on the base. network. Note that the battery will recharge only if necessary. 2. Remove the cable from Plug-It module. • The yellow <CORR> key corrects invalid data entry. Furthermore, the battery has internal temperature control so 3. Remove the screw using Philips screwdriver. • The blue <ADMIN> key is used to access the terminal 2. Ingenico 7780 Packaging Content: it never exceeds 50°C. 4. Take the Plug-It module out. administration function menu. The i7780 with a fully charged battery can execute up to 200 5. Put in the new Plug-It module and secure it with a screw. 1. The I7780 hand held terminal. transactions (depending on the ticket size and transaction 1.3. Magnetic Stripe Card Reader: 2. The battery pack. duration). i7780 features a bi-directional reader capable of reading 3. Thermal printer paper, one roll. The battery status is updated on the handheld display: tracks 1 and 2 simultaneously. The reader is located on 4. The base (optional versatile, radio or charging). the right-hand side. The card can be swiped from the 5. The plug-it module (optional, with the versatile base). 1 bar represents 25 % of full capacity, bottom to the top, or from the top to the bottom. The 6. The power supply (optional, with the base only). 2 bars represent 50 % of full capacity, magnetic stripe on the card has to face down and point 7. The phone cable (optional, with the radio or versatile 3 bars represent 75 % of full capacity, toward the keypad. base only). 4 bars represent 100 % of full capacity


Document Created: 2005-05-10 14:28:59
Document Modified: 2005-05-10 14:28:59
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC