Modular Request

FCC ID: NS9HP900

Cover Letter(s)

Download: PDF
FCCID_4190124

Tel: (403) 248-0028 Fax: (403) 248-2762 E-mail: info@microhardcorp.com www.microhardcorp.com Leaders in Wireless Telecom Modular Approval Request Applicant: Microhard Systems Inc. FCC ID: NS9HP900 Dec 15 2018 To Whom It May Concern: Pursuant to Section 15.212(a)(1) of the FCC rules, the Applicant, request for single modular approval, compliance with the requirements are addressed below. Single Modular Approval Requirements Justification (i) The radio elements of the modular transmitter must have The modular transmitter has its their own shielding. The physical crystal and tuning own RF shielding capacitors may be located external to the shielded radio elements. (ii) The modular transmitter must have buffered The modular transmitter has modulation/data inputs (if such inputs are provided) to buffered modulation/data inputs ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation. (iii) The modular transmitter must have its own power supply The modular transmitter has its regulation. own analog and digital power supply regulation. (iv) The modular transmitter must comply with the antenna and The radio and its associated antennas are provided with the transmission system requirements of §§ 15.203, 15.204(b) special coupling antenna connectors and 15.204(c). The antenna must either be permanently attached or employ a ‘‘unique’’ antenna coupler (at all connections between the module and the antenna, including the cable). The ‘‘professional installation’’ provision of § 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. (v) The modular transmitter must be tested in a stand-alone The modular transmitter was configuration, i.e., the module must not be inside another tested in a stand-alone configuration device during testing for compliance with part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in § 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see § 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see § 15.31(i)).

Tel: (403) 248-0028 Fax: (403) 248-2762 E-mail: info@microhardcorp.com www.microhardcorp.com Leaders in Wireless Telecom (vi) The modular transmitter must be equipped with either a A Label is attached to the device showing the FCC ID permanently affixed label or must be capable of of the device. The manual includes End Device electronically displaying its FCC identification number. labeling instructions. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: ‘‘Contains Transmitter Module FCC ID: XYZMODEL1’’ or ‘‘Contains FCC ID: XYZMODEL1.’’ Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: ‘‘Contains FCC certified transmitter module(s).’’ Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. (vii) The modular transmitter must comply with any specific rules End-users must comply with the following instruction sated or operating requirements that ordinarily apply to a complete in the users’ manual: transmitter and the manufacturer must provide adequate Labeling requirement for equipment using this modular instructions along with the module to explain any such transmitter. RF Exposure Warning for requirements. A copy of these instructions must be included compliance with FCC Rules 2.1091 and 1.1307 when the in the application for equipment authorization. radio is used in a mobile or base system (viii) The modular transmitter must comply with any applicable The module complies with the requirements for a mobile RF exposure requirements in its final configuration. device. Refer to the RF Exposure test report submitted with this application. The EUT is compliant with all applicable RF exposure requirements. Refer to RF Exposure exhibit. See manual for details and limits. Hany Shenouda Director of Engineering Microhard Systems Inc.


Document Created: 2019-02-22 15:49:38
Document Modified: 2019-02-22 15:49:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC