SAR report part 2

FCC ID: NOIKBN647

RF Exposure Info

Download: PDF
FCCID_1340795

APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION D1: PHANTOM

Schmid & Partner Engineering AG s p e a g Zeughausstrasse 43, 8004 Zurich, Switzerland Phone +41 1 245 9700, Fax +41 1 245 9779 info@speag.com, hittp://www.speag.com Certificate of Conformity / First Article Inspection Item Oval Flat Phantom EL1 4.0 Type No QD OVA 001B Series No 1003 and higher Manufacturer SPEAG Zeughausstrasse 43 CH—8004 Zurich Switzerland Tests Complete tests were made on the prototype units QD OVA 001 AA 1001, QD OVA 001 AB 1002, pre—series units QD OVA 001 BA 1003—1005 as well as on the series units QD OVA 001 BB, 1006 ff. Test Requirement Details Units tested Dimensions Compliant with the standard IEC Dimensions of bottom Prototypes, 62209 — 2 [1] requirements for 300 MHz — 6 GHz: Samples longitudinal = 600 mm (max. dimension) width= 400 mm (min dimension) depth= 190 mm Shape: ellipse Material thickness Compliant with the standard IEC Bottom plate: Prototypes, 62209 —— 2 [1] requirements 2.0mm +/ 0.2mm All items Material Dielectric parameters for required 300 MHz — 6 GHz Material parameters frequencies Rel. permittivity = 4 +/—1, sample Loss tangent s 0.05 Material resistivity The material has been tested to be DEGMBE based Equivalent compatible with the liquids defined in simulating liquids phantoms, the standards if handled and cleaned Material according to the instructions. sample Observe Technical Note for material compatibility. Sagging Compliant with the requirements <1% typical < 0.8% if Prototypes, according to the standard. filled with 155mm of Sample Sagging of the flat section when filled HSL900 and without testing with tissue simulating liquid DUT below Standards [1] EC 62209 — 2, Draft Version 0.9, "Evaluation of Human Exposure to Radio Frequency Fields from Handheld and Body—Mounted Wireless Communication Devices in the Frequency Range of 30 MHz to 6 GHz: Human models, Instrumentation and Procedures Part 2: Procedure to determine the Specific Absorption Rate (SAR) for ... including accessories and multiple transmitters", December 2004 Conformity Based on the sample tests above, we certify that this item is in compliance with the standard [1]. Date 07.07.2005 $ e__a 5chm%qAG Signature / Stamp Zoughasfstrasse 4378004 Z\Wfld/ f Phong 41 124 aArdis — info@speag.com, httpiiiwww.speag.com Doc No 881—QD OVA 001B—C Page 1(1)

D2: DOSIMETRIC E-FIELD PROBE

Calibration Laboratory of \\\\‘&7/& Schweizerischer Kalibrierdienst Schmid & Partner : Service suisse d‘étalonnage Engineering AG M Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client BV—ADT (Auden) Certificate No: EX3-3590__Mar10 |CALIBRATION CERTIFICATE | Object EX3DV4 — SN:3590 Calibration procedure(s) QA CAL—01.v6, QA CAL—14.v3, QA CAL—23.v3 and QA CAL—25.v2 Calibration procedure for dosimetric E—field probes Calibration date: March 25, 2010 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter E4419B GB41293874 1—Apr—09 (No. 217—01030) Apr—10 Power sensor E4412A MY41495277 1—Apr—09 (No. 217—01030) Apr—10 Power sensor E4412A MY41498087 1—Apr—09 (No. 217—01030) Apr—10 Reference 3 dB Attenuator SN: $5054 (3c) 31—Mar—09 (No. 217—01026) Mar—10 Reference 20 dB Attenuator SN: $5086 (20b) 31—Mar—09 (No. 217—01028) Mar—10 | Reference 30 dB Attenuator SN: $5129 (30b) 31—Mar—09 (No. 217—01027) Mar—10 Reference Probe ES3DV2 SN: 3013 30—Dec—09 (No. ES3—3013_Dec09) Dec—10 DaAE4 SN: 660 29—Sep—09 (No. DAE4—660_SepO9) Sep—10 Secondary Standards ID # Check Date (in house) Scheduled Check RF generator HP 8648C US3642U01700 4—Aug—99 (in house check Oct—09) In house check: Oct—11 Network Analyzer HP 8753E US37390585 18—Oct—01 (in house check Oct—09) In house check: Oct10 Name Function Signature Calibrated by: Katia Pokovic Technical Manager g Approved by: Niels Kuster Quality Manager Issued: March 25, 2010 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: EX3—3590_Mar10 Page 1 of 11

Calibration Laboratory of »“\‘@’% S Schweizerischer Kalibrierdienst Schmid & Partner i‘r\\\:///% C Service suisse d‘étalonnage Engineering AG € Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland 7L/ NS S Swiss Calibration Service UTnlutabs® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 108 The Swiss Accreditation Service is one of the signatories to the EA Multifateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid NORMx,y,z sensitivity in free space ConvF sensitivity in TSL / NORMx,y,z DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A, B,C modulation dependentlinearization parameters Polarization q ip rotation around probe axis Polarization 9 8 rotation around an axis thatis in the plane normal to probe axis (at measurement center), i.e., 8 = 0 is normal to probe axis Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2003, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", December 2003 b) 1EC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz)", February 2005 Methods Applied and Interpretation of Parameters: * NORMx,y,z: Assessed for E—field polarization 8 = 0 (f < 900 MHz in TEM—cell; f > 1800 MHz: R22 waveguide). NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not effect the E*—field uncertainty inside TSL (see below ConvF). «_ NORM(Mx,y,z = NORMx,y,z * frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. * DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. + Asy,2; Bxiy.z; Cx,y,2, VRxy,z A, B, C are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. «_ ConvF and Boundary Effect Parameters: Assessed in flat phantom using E—field (or Temperature Transfer Standard for f < 800 MHz) and inside waveguide using analytical field distributions based on power measurements for f > 800 MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z * ConyF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from + 50 MHz to + 100 MHz. * Spherical isotropy (3D deviation from isotropy}: in a field of low gradients realized using a flat phantom exposed by a patch antenna. * Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. Certificate No: EX3—3590_Mar1Q Page 2 of 11

EX3DV4 SN:3590 March 25, 2010 Probe EX3BDV4 SN:3590 Manufactured: March 23, 2009 Last calibrated: April 28, 2009 Recalibrated: March 25, 2010 Calibrated for DASY Systems (Note: non—compatible with DASY2 system!) Certificate No: EX3—3590_Mar1O Page 3 of 11

EX3DV4 SN:3590 March 25, 2010 DASY — Parameters of Probe: EX3DV4 SN:3590 Basic Calibration Parameters Sensor X Sensor Y Sensor 2 |Unc (k=2) Norm (uV/(V/im)2)® 0.49 0.49 0.50 _|£10.1% DCP (mv)® 88.1 87.5 87.6 Modulation Calibration Parameters UID Communication System Name PAR A B C VR Unc® dB dBuV mV (k=2) 10000 CW 0.00 X 0.00 0.00 1.00| 300 * 1.5% Y 0.00 0.00 1.00| 300 Z 0.00 0.00 1.00| 300 The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of NormX,Y,Z do not affect the E—field uncertainty inside TSL (see Pages 5 and 6). ® Numerical linearization parameter: uncertainty not required. & Uncertainty is determined using the maximum deviation from linear response applying recatangular distribution and is expressed for the square ofthe field value. Certificate No: EX3—3590_Mar10 Page 4 of 11

EX3DV4 SN:3590 March 25, 2010 DASY — Parameters of Probe: EX3DV4 SN:3590 Calibration Parameter Determined in Head Tissue Simulating Media f [MHz] Validity [MHz]C Permittivity Conductivity ConvF X ConvF Y__ ConvF 2 Alpha Depth Unc (k=2) 900 * 50 / # 100 41.5 £ 5% 0.97 £ 5% 10.25 10.25 10.25 0.74 0.61 #11.0% 1750 + 50 / £ 100 40.1 # 5% 1.37 + 5% 8.89 8.89 8.89 0.76 0.58 £11.0% 1950 + 50 /# 100 40.0 * 5% 140 £ 5% 8.33 8.33 8.33 0.62 0.64 £11.0% 2450 £ 50 /+ 100 39.2 # 5% 1.80 + 5% 7.90 7.90 7.90 0.36 0.84 £11.0% 2600 £ 50 / £ 100 39.0 £ 5% 1.96 # 5% 7.19 7.79 7.79 0.19 1.32 £11.0% 5200 * 50 /# 100 36.0 £ 5% 4.66 4 5% 5.30 5.30 5.30 0.40 1.90 £131% 5300 * 50 / * 100 35.9 £ 5% 4.76 £ 5% 4.92 4.92 4.92 0.45 1.90 £13.1% 5500 £ 50 / x 100 35.6 £ 5% 4.96 + 5% 4.93 4.93 4.93 0.45 1.90 £13.1% 5600 £ 50 /# 100 35.5 £ 5% 5.07 + 5% 4.63 4.63 4.63 0.50 1.90 £131% 5800 £ 50/ 100 35.3 £ 5% 5.27 + 5% 4.54 4.54 4.54 0.50 1.90 £13.1% © The validity of + 100 MHz only applies for DASY v4.4 and higher (see Page 2). The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Certificate No: EX3—3590_Mar10 Page 5 of 11

EX3DV4 SN:3590 March 25, 2010 DASY — Parameters of Probe: EX3DV4 SN:3590 Calibration Parameter Determined in Body Tissue Simulating Media f [MHz] Validity [MHZ]C Permittivity Conductivity ConyFX ConvF Y ConvF 2 Aipha Depth Unc (k=2) 900 * 50 / £ 100 55.0 + 5% 1.05 4 5% 10.20 10.20 10.20 0.60 0.71 #11.0% 1750 £ 50 /# 100 53.4 £ 5% 1.49 + 5% 8.69 8.69 8.69 0.79 0.58 #11.0% 1950 £ 50 / £ 100 53.3 £ 5% 1.52 £5% 8.61 8.61 8.61 0.40 0.80 #11.0% 2450 + 50 / 100 52.7 + 5% 1.95 4 5% 8.20 8.20 8.20 0.28 1.02 £11.0% 2600 £ 50 /+ 100 52.5 4 5% 2.16 £ 5% 8.04 8.04 8.04 0.21 1,25 £11.0% 5200 # 50 / £ 100 49.0 £ 5% 5.30 + 5% 4.80 4.80 4.80 0.53 1.95 £13.1% 5300 * 50 / £ 100 48.5 4 5% 5.42 # 5% 4.50 4.50 4.50 0.53 1.95 #13.1% 5500 + 50 / + 100 48.6 + 5% 5.65 £ 5% 4.32 4.32 4.32 0.55 1.95 £13.1% 5600 # 50 /# 100 48.5 + 5% 5.77 #5% 4.16 4.16 416 0.50 1.95 £13.1% 5800 + 50 / & 100 48.2 4 5% 6.00 £ 5% 4.41 4.41 4.41 0.60 1.95 £13.1% ° The validity of £ 100 MHz only applies for DASY v4.4 and higher (see Page 2). The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band Certificate No: EX3—3590_Mar1O Page 6 of 11

EX3DV4 SN:3590 March 25, 2010 Frequency Response of E—Field {TEM—Cell:ifi110 EXX, Waveguide: R22) 15 ; 14 1.3 : Frequency response (normalized) 1.2 1.1 1.0 0.9 ; 0.8 o.7 . 0.6 0.5 500 1000 1500 2000 2500 s000 f [MHz] —@—TEM —O—R22 Uncertainty of Frequency Response of E—field: £ 6.3% (k=2) Certificate No: EX3—3590_Mar10 Page 7 of 11

EX3DV4 SN:3590 March 25, 2010 Receiving Pattern (¢), 9 = 0° f= 600 MHz, TEM ifi110EXX f= 1800 MHz, WG R22 o3° 0‘- ; }, A eud o—t2ihe—0 —0—30 MHz —BI— 100 MHz —@—600 MHz —IBI— 1800 MHz —&—2500 MHz 120 Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: EX3—3590_Mar1O Page 8 of 11

EX3DV4 SN:3590 March 25, 2010 Dynamic Range f(SARpeaq) (Waveguide R22, f = 1800 MHz) 1.£+06 1.2+05 ; 1.E+04 Input Signal [uV] | Bie0s | 1.E+02 1.E+01 ; 1.2+00 ! i 11O b00 ; 0.0001 0.001 0.01 0.1 1 10 100 SAR [mW/cm‘] —®—not compensated ~—#— compensated Egror [dB] ho o ho 0 0.001 0.01 0.1 1 10 100 SAR [mWicm* Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: EX3—3590_Mar1O Page 9 of 11

EX3DV4 SN:3590 March 25, 2010 Conversion Factor Assessment f= 900 MHz, WGLS R9 (head) f= 1750 MHz, WGLS R22 (head) i 30.0 — ‘ 25.0 SAR[mW/cm®] / W ro § o } e o 8 & o o 0.0 ragr— mm 1 0.0 0 10 20 30 40 50 60 0 10 30 40 z[mm] z[mm] ‘ —@— Analytical —O—Measurements ‘ ‘[ —@— Analytical —O—Measurements Deviation from Isotropy in HSL Error (¢, 8), f = 900 MHz 5Re L : ns o9 fEE $585 borsno A66¢Rfe Error [dB] bhp BI—1.00—0.80 R—0.80——0.60 —0.60——0.40 181—0.40——0.20 1M—0.20—0.00 ©0.00.0.20 M0.20.0.40 ©0.40.0.60 ©0.60—0.80 M0.80—1.00 Uncertainty of Spherical Isotropy Assessment: + 2.6% (k=2) Certificate No: EX3—3590_Mar10 Page 10 of 11

EX3DV4 SN:3590 March 25, 2010 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) Not applicable Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 9 mm Tip Diameter 2.5 mm Probe Tip to Sensor X Calibration Point 1 mm Probe Tip to Sensor Y Calibration Point 1 mm Probe Tip to Sensor Z Calibration Point 1 mm Recommended Measurement Distance from Surface 2 mm Certificate No: £X3—3590_Mar10 Page 11 of 11


Document Created: 2010-08-31 17:27:10
Document Modified: 2010-08-31 17:27:10
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC