User Manual

FCC ID: NOI-406-112503

Users Manual

Download: PDF
FCCID_384657

FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The equipment version marketed in US is restricted to usage of the channels 1-11 only. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) 802.11b Wireless Router This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. User Manual IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The equipment version marketed in US is restricted to usage of the channels 1-11 only CE Mark Warning This equipment complies with the requirements relating to electromagnetic compatibility, EN55022 class B for ITE, the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or reproduced in any form without written consent from the company. Trademarks: All trade names and trademarks are the properties of their respective companies. Copyright © 2003, All Rights Reserved. Document Version: 2.0

Table of Contents Unpacking Information Unpacking Information ············································································· 1 Thank you for purchasing the Wireless Router. Before you start, please check all the Introduction To Wireless Router ······························································ 2 contents of this package. General Description ················································································· 2 Key Features ························································································· 3 The product package should include the following: The Front Panel ······················································································ 4 System LEDs ················································································· 4 Port LEDs (WAN) ············································································ 4 Port LEDs (LAN) ············································································· 4 Port LEDs (Wireless) ······································································· 5 Factory Setting button ······································································ 5 The Rear Panel ······················································································ 6 Power Connection ··········································································· 6 Placement (Optional) ······································································· 6 Installing And Using Wireless Router ······················································ 8 Network configuration setup ··································································· 8 Computer configuration setup································································· 9 Wireless Router configuration setup······················································ 14 Status························································································ 15 Wireless····················································································· 17 TCP/IP Setting············································································ 24 Firewall Configuration·································································· 29 Syslog ······················································································· 33 Statistics ···················································································· 34 1. One Wireless Router Upgrade Firmware ······································································ 34 2. One power adapter Save and Reload ········································································ 35 3. One User Manual (CD) Password··················································································· 35 4. One QIG Product Specifications ··········································································· 36 5. Stand and Screws (Optional) Appendix ································································································· 37 1

Key Features Introduction To Wireless Router The switch provides the following key features: General Description - Complies with 10BASE-T specifications of IEEE802.3 standard - Complies with 100BASE-TX specifications of IEEE802.3u standard The Wireless Router built-in with 4-port 10/100Mbps Fast Ethernet Switch - Complies with IEEE802.3x full duplex operation and flow control is the latest generation of Wireless router product for Home/Office and SOHO - 4 * RJ-45 ports for 100BASE-TX and 10BASE-T connectivity on LAN side users who are thirsting high speed Internet access. This full-feature and - 1 * WAN port on WAN side self-contained compact Wireless Router will be fully for broadband access in - Friendly GUI offers painless setup and management both of LAN and Wireless environment. This device has been specifically - LAN/WAN management via WEB-Based management interface designed to provide LAN and Wireless users the most cost-effective method with - Supports DHCP client/server function multiple accesses to the Internet at the cost of a single public IP address（IP - Supports N-Way Auto-Negotiation on each LAN and WAN port Sharing）and enjoy the true Plug-and-Play installation. Moreover, the built-in - Supports PPPoE protocol 4-port 10/100Mbps switch lets users plug the network cable into the device - Supports NAT/NAPT function without buying additional switch. - Supports Port, IP and MAC filtering, Port Forwarding and Virtual DMZ (Firewall); This device is also an Access Point. It has a built-in wireless LAN. Users WEP and WPA (Wireless) can connect to Internet using wireless network interfaces anywhere within the - Supports extensive LED indicators for network diagnostics range of its radio transmission. It’s idea for SOHO users who require instant and - External power adapter convenient access to Internet without the restriction of connecting cables. - FCC CLASS B, CE The friendly WEB-based graphics interface for setup makes any - Built-in 11Mbps IEEE802.11b wireless LAN Access Point inexperienced users soon enter plug-and–play operation. Embedded DHCP - An instant LAN with an integrated 4 ports 10/100Mbps switch server simplified IP address management and no MIS people needed for daily technical services. What is more, NAT/firewall is also implemented on this compact Router Box for protecting whole LAN from outside attack. 2 3

The Front Panel Port LEDs (Wireless) The front panel of the Wireless Router is shown below. Act LED I. When Wireless AP is ready for data transmitting and receiving, it is steady green. II. When the data is transmitting or receiving, it is blinking green. Factory Setting button System LEDs System LED indicators locate on the front panel for showing the operating 1. Push the button for more than 5 seconds and then release it, the status of the whole device. system will return to factory default setting. In the meantime, system PWR (Power) LED rewrites flash to default value and Status LED halts for a while. This indicator lights green when the Wireless Router is receiving power; Approximately 60 seconds later, the Status LED blinks green otherwise, it is off. periodically, now the whole system parameters have returned to factory default value. If the process has been interrupted by any Status LED reason (power off…), the system will fail. Before performing the The LED will be dark for a few seconds when the system is started. process, ensure a safe operating environment please！ After that, the LED will blink periodically to show the Wireless Router 2. To reboot the Router, Press the button for 2-5 seconds and then is working normally. If the LED stays green/dark that means the release it, and all the setting won’t be erased. Wait for the Router to system failed, you need to contact your agent or try to reboot the complete the reboot, and then you can start to use it. system. Warning：Incomplete factory setting recovery procedure will cause the Port LEDs (WAN) Wireless Router malfunction！If you are unfortunately in this Port LED (WAN) indicators locate on the front panel for showing the situation, do not try to repair it by yourself. Consult your local operating status of WAN port. distributor for help！ Act/Link LED The LED stays light (green) means the port has good linkage to its associated devices. The LED will blink green when there is traffic transverse the port. Port LEDs (LAN) Port LEDs (LAN) indicators locate on the front panel for showing the operating status of 10/100Mbps Fast Ethernet switching ports. Act/Link LED Every port has a Act/Link LED. Steady green (link state) indicates that the port has good linkage to its associated devices. Flashing green indicates that the port is receiving or transmitting data between its associated devices. 4 5

The Rear Panel 4. Insert the provided screws in each hole of the stand parts. 5. Attaches the unit to the anchors on the wall. The rear panel of the Wireless Router is shown below Stand Option 1. The Router includes two stand parts. 2. Combine two parts into one stand. Combine it with the side of router near the power port. Push the stand up to snap it into place. 3. Place the Router. Power Connection Plug the circle end of the power adapter firmly into the rear panel of the Wireless Router, and the other end put into an electric service outlet then the system is ready. Placement (Optional) There are three ways to place the Router. The first way is to place the Router horizontally on a surface. The second way is to attach the router to the wall. The third way is to stand the Router vertically on a surface. These options are explained in further detail below. Desktop Option 1. The Router has one plastic stand that can be divided into two parts. 2. Combine one part of stand with the side of router. 3. Do the same with the second part. 4. Place the Router Wall-mount option Before attach this router on the wall, you have to finish the desktop option steps first. 1. Select a location with access for cables and a power outlet. 2. Unplug the unit. Place it upside down on a flat surface and mark the two holes for anchors. 3. Installing the Wall mount anchor (plastic) into the wall with tools such as drill or hammer. 6 7

Installing And Using Wireless Router Computer configuration setup In order to communicate with Wireless Router, the connected computer needs to This Chapter provides a step-by-step guide to the installation and install the TCP/IP protocol and setup the related address information. configuration of the Wireless Router. It assumes that your computers use the Windows 95/98 or newer version and a WEB browser is installed for 1. Double click the “My Computer” icon on the desktop screen configuration purposes. We suggest you go over the whole chapter and then do more advanced operation. Network configuration setup Steps to build up the network: Connect the ADSL or Cable modem to the Ethernet WAN port on the back of the Wireless Router by using the UTP cable. Connect the phone line from the wall socket to the line-in port on the ADSL modem, or the coaxial cable to the line-in port on the Cable modem. Plug-in the power adapter to the modem and turn on the power. Install the Ethernet card into the computer by referring to the User Guide that came with the card. Connect the computer to the Wireless Router by using standard twisted-pair Ethernet cable from the computer’s Ethernet card to an 10/100Mbps Ethernet port on the back of the Wireless Router. Plug-in the power adapter to the Router and the other side to the wall outlet. 2. Double click the “Control Panel” icon on the My Computer window 8 9

3. Double click the “Network” icon on the Control Panel window 5. Select “Protocol” item on the Select Network Component Type window. After that, click “Add” button 6. Select “Microsoft” item on the left side of Select Network Protocol window. After that, select “TCP/IP” protocol on the Network Protocols block and click “OK” button. 4. Click the “Configuration” tab and check the TCP/IP protocol is available or not. If yes, skip the procedures 5 ~ 6. If no, click the “Add” button. 7. Select the “TCP/IP” component in the Configuration tab of the Network window. Click “Properties” button. 10 11

8. The screen will show up the TCP/IP Properties window then start the setting. First NOTE：1. The default IP address of Wireless Router is 192.168.1.1 and subnet of all, you need to choose the IP address is dynamically assigned by a DHCP mask is 255.255.255.0 server or fixed. 2. For the new network computers to use dynamic IP addresses provided by the Wireless Router DHCP server, they should not use the range of fixed IP addresses. For example, If the fixed IP addresses already use 192.168.1.2 to 192.168.1.68 the DHCP server must be setup to allocate the dynamic addresses out of this range. 9. The screen will return back to Network window then click “OK” button. At this moment, the system will prompt you for restarting the Windows. Click “Yes” Dynamically assigned: - Select the “IP Address” tab and select “Obtain an IP address automatically” (default setting) - Select the “Gateway” tab and click “Remove” to clear any existing entry of gateway IP address - Select the “DNS Configuration” tab and click “Disable DNS” - Click “OK” button Fixed: If there are some clients who need to get fixed IP addresses for some reasons and the nodes also need to access Internet through the Wireless Router then the following steps used to configure system - Select “Specify an IP address” in the IP Address Tab of the TCP/IP Properties window and enter 192.168.1.*** in the IP Address field (the *** is a number between 2 and 254 used by the Wireless Router to identify individual computers) - Select the “Subnet Mask” field and enter 255.255.255.0 - Select the “DNS Configuration” tab and click “Enable DNS” - Enter the DNS IP Address obtained from your ISP in the “Server Search Order” location. Click ”OK” button. 12 13

Status Wireless Router configuration setup In the home page of the Wireless Router, the left navigation bar shows the options to configure the system. In the right navigation screen is the In order to make the whole network operate successfully, it is necessary to summary of system status for viewing the configurations. configure the Wireless Router through your computer has a WEB browser installed. Please follow up the steps listed below. 1. Double click the Internet WEB browser icon on your desktop screen (Netscape Communicator 4.0 and Internet Explorer 3.0 or update version) 2. Type 192.168.1.1 into the URL WEB address location and press Enter. 3. The Username and Password Required window appears. - Enter admin in the User Name location (default value). - Enter admin in the Password location (default value). - Click “OK” button1 System Alias Name Name of Router Up-time Total of operation time Firmware version Version of Firmware Wireless Configuration SSID This is the name of the wireless LAN. All the devices in the same wireless LAN should have the same SSID. Channel Number The channel used by the wireless LAN. All devices in the same wireless LAN should use the same channel. Encryption Type of Encryption 1 Don’t forget to change the Username and Password in configuration’s Authentication to ensure the security. 14 15

Wireless Wireless Access Point builds a wireless LAN and can let all PCs equipped with Associate Clients Number of all active wireless stations that are IEEE802.11b wireless network adaptor connect to your Intranet. It supports WEP connecting to the access point. encryption and MAC address filter to enhance the security of your wireless BSSID Basic Service Set Identification of AP network. Basic Setting LAN Configuration IP Address IP Address of Router You can set up the configuration of your Wireless and monitor the Wireless Clients associate with your AP. Subnet Mask Subnet Mask DHCP Server Enabled or Disable of DHCP MAC Address MAC Address of LAN-port WAN Configuration Attain IP Protocol Static IP address IP Address IP address of WAN-port Subnet Mask Subnet Mask of WAN-port Default Gateway Default Gateway of WAN-port MAC Address MAC Address of WAN-port Configuration Alias Name The name of Router □Disable Wireless LAN To Disable interface of Wireless LAN Interface SSID The name of Wireless Country Select the country where you are to decide the Channel number Channel Number The channel used by the wireless LAN. All devices in the same wireless LAN should use the same channel. Associated Clients Click "Show Active Clients" button, then an "Active Wireless Client Table" will pop up. You can see the status of all active wireless stations that are connecting to the access point. 16 17

Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) Advanced Settings You can set advanced wireless LAN parameters of this router. The parameters include Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval, Tx Operation Rate, Tx Basic Rate, Preamble Type, and Broadcast SSID. You should not change these parameters unless you know what effect the changes will have on this router. Active Wireless Client Table MAC Address MAC address of this active wireless station. Tx Packet The number of transmitted packets that are sent out from this active wireless station. Rx Packet The number of received packets that are received by this active wireless station. TX Rate The transmission rate Configuration Power Saving Shows if the wireless client is in Power Saving mode Wireless AP can associate with this Open System Expired Time This is the time in second before dissociation. If the wireless router without WEP mode wireless keeps idle longer than the expired time, this encryption. wireless router will dissociate it. The wireless client You should also setup WEP key in station has to associate again when it is active. the "Security" page and wireless AP Authentication Shared Key Refresh Refresh the "Active Wireless Client Table". associating with this wireless router Type mode should use WEP encryption in the Close Close the "Active Wireless Client Table". authentication phase. The wireless client can associate Auto with this wireless router by using any one of these two Modes. Fragment To specifies the maximum size of packet during the Threshold data transition. The lower values you set, the worst performance it will be. 18 19

If the packet size is smaller the RTS threshold, the Wireless Security Setup RTS wireless router will not send this packet by using the At the page, you can set up the WEP, WPA Encryption to ensure the Threshold RTS/CTS mechanism. security of your Wireless. Beacon The period of time how long a beacon is Interval broadcasted. The "Data Rate" is the data packets limitation this wireless router can transmit. The wireless router will Data Rate use the highest possible selected transmission rate to transmit the data packets. It defines the length of CRC block in the frames Preamble during the wireless communication. "Short Preamble" Type is suitable for heavy traffic wireless network. "Long Preamble" provides much communication reliability If you enable "Broadcast SSID", every wireless station located within the coverage of this wireless Broadcast router can discover this wireless router easily. If you SSID are building a public wireless network, enabling this feature is recommended. Disabling "Broadcast SSID" can provide better security. To enables multiple AP to communicate and pass IAPP information regarding the location of associated Configuration Stations. Encryption To enable WEP or WPA encryption, select Click <Apply> at the bottom of the screen to save the above configurations. You can now configure the option in the drop list. If you select none, other advance sections or start using the router. any data will be transmitted without Encryption and any station can access the router. Use 802.1x To enable the 802.1x, Click the check box of Authentication the item. WPA There are two items, “WPA-Radius” and Authentication “pre-shared key”. You can select the mode by Mode clicking the item. WPA Unicast To enable “TKIP”, click the check box. Cipher Suite Pre-Shared key To decide the format, select what you need in Format the drop list. 20 21

WDS Setting Authentication If you use RADIUS Sever to ensure your RADIUS Sever security, you have to set up the parameters in the item. To set up the Port, IP address and Password of your RADIUS, Enter the Port Number, IP and Password. Click <Apply Change> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router. Access Control To restrict the Number of Access authentication of Stations, Set up the control list in this page. Wireless Distribution System allows the router to communicate with other APs wirelessly. To make it work, you must ensure that these APs and the Router are in the same Channel and add these APs MAC Address and Comment values into the WDS list. Don’t Forget to Enable the WDS by click the check box of “Enable WDS” and press “Apply Changes” button to save. To Delete the AP on the list, Click the check box in the select item and click the “Delete Selected”. If you want to delete all APs on the list, click “Delete All” to remove all of them. Configuration Enable Wireless To enable it, click the check box. Access control MAC Address & To set up the Value of MAC Address & Comment Comment; enter the MAC Address and Comment of station and click Apply Changes to save. Current Access To Delete the station on the list, Click the check Control list box in the select item and click the “Delete Selected”. If you want to delete all stations on the list, click “Delete All” to remove all of them. Click <Apply Change> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router. 22 23

TCP/IP Setting WAN Interface Setup LAN Interface Setup In the page, you can set up the three types of Internet Access, PPPoE, To set up the configuration of LAN interface, Private IP of you router LAN DHCP, and Fixed IP. Port and Subnet mask for your LAN segment. Configuration IP address The IP of your Router LAN port (Default 192.168.1.1) Subnet Mask Subnet Mask of you LAN (Default 255.255.255.0) 802.1d To prevent from network loops and preserve the Spanning tree quality of bridged network Default To set up the Default Gateway, enter the IP Value. Gateway To give your LAN Client an IP, you have to enable “DHCP”. If not, manual setting up your client IP is DHCP necessary when you want to use the router as your client’s default gateway. To assign an IP for a specified MAC-address, Enter DHCP Static the MAC-address, IP, Comment name in the Text-box Assignment and Click “Apply Changes” to save. 24 25

Connect on demand is for bill by connection time. You can set up the Idle time for the value specifies the number of time that elapses before the system automatically disconnects the PPPoE session. Manual To connect to ISP, click “Connect” manually from the WEB user interface. The WAN connection will not disconnected due to the idle timeout. If the WAN line breaks down and latter links again, the router will not auto-connect to the ISP. Idle time The value specifies the number of idle time (Minute) that elapses before the system automatically disconnects the PPPoE session. DNS If your DNS provide by ISP is dynamic, choose “Attain DNS automatically” To specify the DNS, and enter the DNS provided by your Configuration ISP in DNS 1 2 3. DHCP If your connection type is DHCP; select “Attain IP When ISP use MAC address authentication (with DHCP), automatically (DHCP)”. then the MAC address of the Ethernet card attached to your When you ISP use Static IP, you have to select “Fixed IP” Cable modem must be registered with the ISP before Fixed IP and enter the IP address, Subnet Mask and Default connecting to the WAN (Internet). If the Ethernet card is Gateway provided by Your ISP. changed, the new MAC address must be registered with Clone the ISP. When your connection type is PPPoE, You need to enter MAC cloning feature allows the MAC address reported by Mac PPPoE the information provided by your ISP, Such as User name, WAN side network interface card to be set to the MAC Address Password, Connection type (continuous, connect on address already registered with the ISP eliminating the demand and manual), and Idle Time. need to register the new MAC address with the ISP. This Username EX. Peter feature does not change the actual MAC address on the NIC, but instead changes the MAC address reported by Password EX.12345 Wireless Router to client requests. Connection Continuous is for Always keep connection To Change the MAC address, enter it in the text box. Type Enable To Enable the user to access this Router through Internet, WAN Enter the specific IP and the port number Access 26 27

The Dynamic DNS feature allows you to dynamically Firewall Configuration register your assigned IP address to an Internet resolvable Fully Qualified Domain Name (FQDN). This is especially The firewall could not only obstruct outside intruders from intruding useful if you have a dynamically assigned IP address and you want to maintain a constantly resolvable web address. your system, but also restricting the LAN users. Port Filtering To restrict certain type of data packets from your LAN To enable Dynamic DNS, select Enable in the Dynamic to Internet through the Router, add them on the Current Filtering Enable DNS checkbox control, select a dynamic DNS service DDNS provider from the Service Provider drop list, and enter the Table. host name, username and password in the Host Name, Username and Password fields. Note: You must create an account with the selected provider before using this feature. Note. Wildcard and Mail Exchanger service depend on the service providers. To Enable the Maximum Transmission Unit of Router setup. Any packet over this number will be chopped up into Enable suitable size before sending. Larger number will enhance MTU the transmission performance. Setup Enter your MTU number in the text-box to set the limitation. Default is 1500. Configuration STEPS 1. Click the check box of “Enable Port Filtering” to enable the function. 2. Enter the Port range (EX 25-110), Protocol (UDP/TCP), and comment (EX. E-Mail) 3. To Delete the Port range on the list, Click the check box in the select item and click the “Delete Selected”. If you want to delete all entries on the list, click “Delete All” to remove all of them. Click <Apply Change> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router. 28 29

IP filtering MAC filtering The Wireless Router could filter the outgoing packets for security or The Wireless Router could filter the outgoing packets for security or management consideration. You can set up the filter against the IP management consideration. You can set up the filter against the addresses to block specific internal users from accessing the MAC addresses to block specific internal users from accessing the Internet. Internet. Configuration Configuration STEPS 1. Click the check box of “Enable IP Filtering” to enable STEPS 1. Click the check box of “Enable MAC Filtering” to the function. enable the function. 2. Enter the specific Local IP address (EX 10.10.3.9), 2. Enter the specific MAC address (EX 00:0e:b6:a8:72), Protocol (UDP/TCP), and comment (EX. Peter) and comment (EX. Peter) 3. To Delete the IP address on the list, Click the check 3. To Delete the Mac address on the list, Click the box in the select item and click the “Delete Selected”. check box in the select item and click the “Delete If you want to delete all entries on the list, click Selected”. If you want to delete all Entries on the list, “Delete All” to remove all of them. click “Delete All” to remove all of them. Click <Apply Change> at the bottom of the screen to save the above configurations. You Click <Apply Change> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router. can now configure other advance sections or start using the router. 30 31

Port forwarding Virtual DMZ The Port Forwarding allows you to re-direct a particular range of service The virtual DMZ is used to enable protocols, which need to open ports on the router. The router will forward all unspecified incoming traffic to the port numbers (from the Internet/WAN Ports) to a particular LAN IP host specified in this page. address. It helps you to host some servers behind the router NAT firewall. To configure it, enter the Host IP (private IP address) and Click “Apply changes” to enact the setting. Syslog Configuration View and save the log in remote machine on the page. To enable the system log, STEPS 1. Click the check box of “Enable port forwarding” to 1. Click the check box enable the function. 2. Click show log to monitor. 2. Enter the specific IP address (EX 10.10.10.10), To enable the Remote system log, Protocol (UDP/TCP), Port range (EX 25-110), and comment (EX. E-Mail) 1. Click the check box 2. Enter the remote machine IP address 3. To Delete the IP address on the table, Click the check box in the select item and click the “Delete Selected”. If you want to delete all Entries on the table, click “Delete All” to remove all of them. Click <Apply Change> at the bottom of the screen to save the above configurations. 32 33

Statistics Save and Reload On this page, you can monitor the sent & received packets counters of To save setting to file, click “Save...” button. wireless, Ethernet LAN, and Ethernet WAN. To see the latest report, click To load setting from file, refresh button. 1. Click “Browse…” on the to select the file 2. Click upload to start the process and wait for it to complete To reset setting to Default, click reset to start the process and it will be completed till the status LED start blinking. Upgrade Firmware To Upgrade Firmware, Password To set up the Administrator Account information, enter the Username, New STEPS 1. Click “browse…” button to select the firmware you want to upgrade. password, and reenter the password on the text box. Don’t forget to click the “Apply Changes” to save the configuration. 2. Click Upload to start the upgrade process. Please don’t close the WEB-browser and wait for process to complete. When Upgrade is completed, you can start to use the router. 34 35

Product Specifications Appendix IEEE802.3, 10BASE-T Service Name, Protocol and Port number IEEE802.3u, 100BASE-TX Standard IEEE802.3x full duplex operation and flow control Service Protocol Port Service Protocol Port IEEE802.11b wireless LAN infrastructure ANY Any Any AOL TCP 5190-5194 1 * WAN port BGP TCP 179 Finger TCP 79 Interface 4 * 10/100 RJ-45 Fast Ethernet switching ports FTP TCP 20-21 Gopher TCP 70 One wireless LAN comply with IEEE 802.11b HTTP TCP 80 HTTPS TCP 443 WAN Connection Ethernet 10/100 Mbps IMAP TCP 143 InterLocator TCP 389 RJ-45 (10BASE-T): Category 3,4,5 UTP Cable Connections RJ-45 (100BASE-TX): Category 5 UTP IRC TCP 6660-6669 L2TP TCP 1701 LAN: Auto-Negotiation (10Mbps, 100Mbps) VDOLive TCP 7000-7010 WAIS TCP 210 Network Data Rate Wireless: 11Mbps, 5.5Mbps, 2Mbps, 1Mbps data rated and WINFRAME TCP 1494 X-WIN TCP 6000-6030 auto-fallback support DNS UDP 53 IKE UDP 500 Transmission Mode Auto-Negotiation (Full-duplex, Half-duplex) NFS UDP 111 NTP UDP 123 System PC-Anywhere UDP 123 RIP UDP 520 Power SNMP UDP 161 SYSLOG UDP 514 Status TALK UDP 517-518 TFTP UDP 69 Port (WAN) UDP-Any UDP Any UUCP UDP 540 LED indications ACT/LINK PING ICMP ANY TRACEROUTE ICMP Any Port (LAN) ACT/LINK Port(Wireless) ACT Embedded WEB based management interface LAN/WAN management via WEB-based management interface DHCP client / server function Firmware upgradeable Software Support PPPoE protocol NAT / NAPT function Port filtering IP filtering MAC filtering Virtual DMZ Built-in 11Mbps wireless Access Point Direct Sequence Spread Spectrum (DSSS) operating at Wireless Access Point unlicensed 2.4 GHz ISM band 64/128bit Wired Equivalent Privacy (WEP) data encryption Emission FCC CLASS B, CE Operating Temperature 00 ~ 500C (320 ~ 1220F) Operating Humidity 10% - 90% Power Supply External Power Adapter, 12VDC/500mA 61NB-04600-207 36 37


Document Created: 2003-12-16 18:30:48
Document Modified: 2003-12-16 18:30:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC