SAR Report (Appendix C-2)

FCC ID: NM8X2-HT

RF Exposure Info

Download: PDF
FCCID_3609031

Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 34.2 +6 % 4.93 mho/m + 6 % Head TSL temperature change during test <0.5 °C «+ SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.29 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 82.2 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.35 Wikg SAR for nominal Head TSL parameters normalized to 1W 23.2 Wikg + 19.5 % (k=2) Head TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 965.3 5.27 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 33.9 +6 % 5.13 mho/m + 6 % Head TSL temperature change during test «05 °C ~——— ———— SAR result with Head TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 7.94 W/kg SAR for nominal Head TSL parameters normalized to 1W 78.7 Wikg + 19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Head TSL condition SAR measured 100 mW input power 2.24 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 22.1 Wikg £ 19.5 % (k=2) Certificate No: D5GHzV2—1203_Dec16 Page 5 of 16

Body TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 49.0 5.30 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 47.1 x6 % 5.46 mho/m + 6 % Body TSL temperature change during test «0.5 °C =«= SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.20 W/kg SAR for nominal Body TSL parameters normalized to 1W 71.5 Wikg + 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.02 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.0 W/kg + 19.5 % (k=2) Body TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.42 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.9 + 6 % 5.59 mho/m + 6 % Body TSL temperature change during test <0.5 °C ———— faee SAR result with Body TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.70 Wi/kg SAR for nominal Body TSL parameters normalized to 1W 76.4 W/kg x 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.17 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.5 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1203_Dec16 Page 6 of 16

Body TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.6 5.65 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.5 + 6 % 5.86 mho/m + 6 % Body TSL temperature change during test <0.5 °C ———— ———— SAR result with Body TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.91 W/kg SAR for nominal Body TSL parameters normalized to 1W 78.5 Wikg + 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.19 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.7 Wikg + 19.5 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.4 + 6 % 6.00 mho/m + 6 % Body TSL temperature change during test «0.5 °C ««== se« SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.80 W/kg SAR for nominal Body TSL parameters normalized to 1W 77.4 Wikg + 19.9 % (k=2) SAR averaged d over 10 cm cm‘ (10 g) g) ofof Body Body TSL condition SAR measured 100 mW input power 2.18 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.6 W/kg + 19.5 %(k=2) Certificate No: D5SGHzV2—1203_Dec16 Page 7 of 16

Body TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 46.0 + 6 % 6.28 mho/m + 6 % Body TSL temperature change during test <0.5 °C ses« se« SAR result with Body TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.47 W/kg SAR for nominal Body TSL parameters normalized to 1W 74.1 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.06 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.4 Wikg + 19.5 %(k=2) Certificate No: D5GHzV2—1203_Dec16 Page 8 of 16

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 47.9 Q — 5.9 jQ Return Loss —23.9 dB Antenna Parameters with Head TSL at 5300 MHz Impedance, transformed to feed point 48.7 Q — 0.5 jQ Return Loss — 36.8 dB Antenna Parameters with Head TSL at 5500 MHz Impedance, transformed to feed point 47.2 Q + 0.3 jQ Return Loss —30.9 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 51.9 0 +2.1 jQ Return Loss —31.2 dB Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point 51.2 Q + 4.9 jQ Return Loss —26.0 dB Antenna Parameters with Body TSL at 5200 MHz Impedance, transformed to feed point 48.0 Q — 5.4 jQ Return Loss —24.6 dB Antenna Parameters with Body TSL at 5300 MHz Impedance, transformed to feed point 48.5 Q + 1.5 jQ Return Loss — 33.6 dB Antenna Parameters with Body TSL at 5500 MHz Impedance, transformed to feed point 47.6 0 + 1.8 jQ Return Loss — 30.3 dB Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 52.7 Q + 3.4 jQ Return Loss — 27.5 dB Certificate No: D5GHzV2—1203_Dec16 Page 9 of 16

Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point 51.6 Q + 5.5 jQ Return Loss —25.0 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.192 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on September 11, 2014 Certificate No: D5GHzV2—1203_Dec16 Page 10 of 16

DASY5 Validation Report for Head TSL Date: 16.12.2016 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole DSGHzV2; Type: DSGHzV2; Serial: DSGHzV2 — SN:1203 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 0 = 4.53 S/m; s= 34.8; p = 1000 kg/m} ¢ Medium parameters used: f = 5300 MHz; 0 = 4.63 S/m; & = 34.6; p = 1000 kg/m3 > Medium parameters used: £= 5500 MHz; 0 = 4.82 $/m; &, = 34.4; p = 1000 kg/m3 ; Medium parameters used: f = 5600 MHz; 0 = 4.93 S/m; &, = 34.2; p = 1000 kg/m“ s Medium parameters used: £ = 5800 MHz; 0 = 5.13 S/m; & = 33.9; p = 1000 kg/m} Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(5.59, 5.59, 5.59); Calibrated: 30.06.2016, ConvF(5.14, 5.14, 5.14); Calibrated: 30.06.2016, ConvF(5.02, 5.02, 5.02); Calibrated: 30.06.2016, ConvF(4.89, 4.89, 4.89); Calibrated: 30.06.2016, ConvF(4.85, 4.85, 4.85); Calibrated: 30.06.2016; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 30.12.2015 e Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 DASY52 52.8.8(1258); SEMCAD X 14.6.10(7372) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 69.00 V/m; Power Drift = —0.06 dB Peak SAR (extrapolated) = 28.5 W/kg SAR(I g) =7.88 W/kg; SAR(10 g) = 2.23 W/kg Maximum value of SAR (measured) = 17.8 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 69.55 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) =31.0 W/kg SAR(1 g) = 8.33 W/kg; SAR(10 g) = 2.38 W/kg Maximum value of SAR (measured) = 19.4 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 68.79 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) =32.1 W/kg SAR(1 g) = 8.21 W/kg; SAR(10 g) = 2.33 W/kg Maximum value of SAR (measured) = 19.2 W/kg Certificate No: D5GHzV2—1203_Dec16 Page 11 of 16

Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 68.81 V/m; Power Drift = —0.06 dB Peak SAR (extrapolated) = 32.7 W/kg SAR(I g) = 8.29 W/kg; SAR(10 g) = 2.35 W/kg Maximum value of SAR (measured) = 19.6 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 66.17 V/m; Power Drift = —0.03 dB Peak SAR (extrapolated) = 32.6 W/kg SAR(1 g) = 7.94 W/kg; SAR(10 g) = 2.24 W/kg Maximum value of SAR (measured) = 19.1 W/kg dB —6.00 —12.00 —18.00 —24.00 —30.00 0 dB = 17.8 W/kg = 12.50 dBW/kg Certificate No: D5GHzV2—1203_Dec16 Page 12 of 16

Impedance Measurement Plot for Head TSL 16 Dec 2016 12137125 CHI) sii 1 U Fs 4: 47.850 a —5.8789 0 5.2062 pF 5 200.000 000 MHz ——r—~— CH1 Markers Del 2: 48.670 o ~501.95 m Cor 5.30000 GHz 3: 47,236 o 0.3320 a 5.50000 GHz ftg 16 sses6 0 GHz 197 4 #4 n GHz H1d CH2 CH2 Markers 2:—36.916 dB for 5.30000 6Hz 3:—30,.957 dB 5.50000 GHz 41—31.299 dB fvg 5.60000 GHz 16 5:—26,.030 dB 5.80000 GHz H1d START 5 000.000 000 MHz STOP 6 000.000 000 MHz Certificate No: D5GHzV2—1203_Dec16 Page 13 of 16

DASY5 Validation Report for Body TSL Date: 16.12.2016 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole DSGHzV2; Type: D5SGHzV2; Serial: DSGHzV2 — SN:1203 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 0 = 5.46 S/m; & = 47.1; p = 1000 kg/m3 $ Medium parameters used: f = 5300 MHz; 0 = 5.59 S/m; &, = 46.9; p = 1000 kg/m" 4 Medium parameters used: £ = 5500 MHz; 0 = 5.86 S/m; &, = 46.5; p = 1000 kg/m“ , Medium parameters used: f = 5600 MHz; o = 6 S/m; &, = 46.4; p = 1000 kg/m3 s Medium parameters used: f = 5800 MHz; 0 = 6.28 S/m; &, = 46; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN3503; ConvF(4.99, 4.99, 4.99); Calibrated: 30.06.2016, ConvF(4.75, 4.75, 4.75); Calibrated: 30.06.2016, ConvF(4.4, 4.4, 4.4); Calibrated: 30.06.2016, ConvF(4.35, 4.35, 4.35); Calibrated: 30.06.2016, ConvF(4.27, 4.27, 4.27); Calibrated: 30.06.2016; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 $Sn601; Calibrated: 30.12.2015 e Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 * DASY532 52.8.8(1258); SEMCAD X 14.6.10(7372) Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 65.37 V/m; Power Drift = —0.08 dB Peak SAR (extrapolated) =27.1 W/kg SAR(1 g) =7.2 W/kg; SAR(10 g) = 2.02 W/kg Maximum value of SAR (measured) = 16.4 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.02 V/m; Power Drift = —0.06 dB Peak SAR (extrapolated) = 29.3 W/kg SAR(I g) =7.7 W/kg; SAR(10 g) = 2.17 W/kg Maximum value of SAR (measured) = 17.6 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 67.30 V/m; Power Drift = —0.05 dB Peak SAR (extrapolated) = 32.1 W/kg SAR(I g) =7.91 W/kg; SAR(10 g) = 2.19 W/kg Maximum value of SAR (measured)= 18.5 W/kg Certificate No: D5GHzV2—1203_Dec16 Page 14 of 16

Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5600 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 66.08 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 32.2 W/kg SAR(I g) =7.8 W/kg; SAR(10 g) = 2.18 W/kg Maximum value of SAR (measured) = 18.4 W/kg Dipole Calibration for Body Tissue/Pin=100mW, dist=10mm, £=5800 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 63.53 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 32.8 W/kg SAR(I g) =7.47 W/kg; SAR(10 g) = 2.06 W/kg Maximum value of SAR (measured) = 18.1 W/kg dB —6.00 —12.00 —18.00 —24.00 —30.00 0 dB = 16.4 W/kg = 12.15 dBW/kg Certificate No: D5GHzV2—1203_Dec16 Page 15 of 16

Impedance Measurement Plot for Body TSL 16 Dec 2016 12:36:51 CHI) sii £ U Fs 1:47.996 n —5.4473 0 5§.6197 pF 5 200.000 06o MHz / p CH1 Markers 2: 48.547 a fvg 16 H1d es ze*" CH2 CH2 Markers 2:1—33,602 dB Cor 5.30000 GHz 3:—30.260 dB 5.50000 GHz 4:—27.497 dB Av 5.G0000 GHz 16 * 5:—24,.951 d8 5.90000 GHz H1d START 5 000.000 agd MHz STOP 6 600.000 00 MHz Certificate No: D5GHzV2—1203_Dec16 Page 16 of 16

i) zies —fsmerass.‘ ,/’I mm® in Colisboration with )4 NNX L PBWH uy CALIBRATION LABORATORY j$y oong _ Nee CAIBRATION Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China /,,,"h‘\“\\ CNAS LO570 Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Hittp://www.chinattl.cn Client Auden Certificate No: 2Z17—97052 Object EX3DV4 — SN:3753 Calibration Procedure(s) FF—211—004—01 Calibration Procedures for Dosimetric E—field Probes Calibration date: May 05, 2017 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(Sl). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility;: environment temperature(22+3)‘C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 101919 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Power sensor NRP—Z91 101547 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Power sensor NRP—Z91 101548 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Reference10dBAttenuator 18N50OW—10dB 13—Mar—16(CTTL,No.J16X01547) Mar—18 Reference20dBAttenuator 18N5OW—20d4B 13—Mar—16(CTTL, No.J16X01548) Mar—18 Reference Probe EX3DV4 SN 7433 26—Sep—16(SPEAG,No.EX3—7433_Sep16) Sep—17 DAE4 SN 549 13—Dec—16(SPEAG, No.DAE4—549_Dec16) Dec—17 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration SignalGeneratorMG3700A 6201052605 27—Jun—16 (CTTL, No.J16X04776) Jun—17 Network Analyzer E5071C MY46110673 13—Jan—17 (CTTL, No.J17X00285) Jan —18 Name Function Signature Calibrated by: Yu Zongying SAR Test Engineer % Reviewed by: Lin Hao SAR Test Engineer 'flif’% Approved by: Qi Dianyuan SAR Project Leader C%‘i_/ Issued: May 06, 2017 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z17—97052 Page 1 of 11

m© |., Collsboration with a=‘/"[‘J, magys>" a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Http://www.chinattl.cn Glossary: TSL tissue simulating liquid NORMx,y,z sensitivity in free space Convr sensitivity in TSL / NORMx,y,z DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A,B,C,D modulation dependent linearization parameters Polarization ® ® rotation around probe axis Polarization 0 0 rotation around an axis that is in the plane normal to probe axis (at measurement center), i 0=0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) for hand—held devices used in close proximity to the ear (frequency range of 300MHz to 3GHz)", February 2005 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Methods Applied and Interpretation of Parameters: e NORMx,y,z: Assessed for E—field polarization 0=0 (fs900MHz in TEM—cell; f> 1800MHz: waveguide). NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not effect the E° —field uncertainty inside TSL (see below ConvF). e NORM(Px,y,z = NORMx,y,z* frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of Convr. e DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep (no uncertainty required). DCP does not depend on frequency nor media. e PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics. e Ax,y,z; Bx,y,z; Cx,y,z;VRx,y,z:A,B,C are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. e ConvrF and Boundary Effect Parameters: Assessed in flat phantom using E—field (or Temperature Transfer Standard for f<800MHz) and inside waveguide using analytical field distributions based on power measurements for f >800MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty valued are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z* ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from+50MHz to+100MHz. e Spherical isotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. e Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. e Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: Z17—97052 Page 2 of 11

ie© |., Colisoration with =‘/"[‘]I, es‘ a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Http://www.chinattl.cn Probe EX3DV4 SN: 3753 Calibrated: May 05, 2017 Calibrated for DASY/EASY Systems (Note: non—compatible with DASY2 system!) Certificate No: Z17—97052 Page 3 of 11

e© |n, Collsboration with =‘/"/‘[, iaaaye»" a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2218 Fax: +86—10—62304633—2209 E—mail: cttl@chinattl.com Http://www.chinattl.cn DASY/EASY — Parameters of Probe: EX3DV4 — SN: 3753 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm(pV/(V/m))A 0.47 0.30 0.46 £10.0% DCP(mV)® 101.4 107.2 104.5 Modulation Calibration Parameters UID Communication A B C D VR Unc ® System Name dB dB/uV dB mV (k=2) 0 CW X 0.0 0.0 1.0 0.00 185.8 +£2.0% Y 0.0 0.0 1.0 141.4 Z 0.0 0.0 1.0 182.6 The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. * The uncertainties of Norm X, Y, Z do not affect the E®—field uncertainty inside TSL (see Page 5 and Page 6). ® Numerical linearization parameter: uncertainty not required. € Uncertainly is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: Z17—97052 Page 4 of 11


Document Created: 2017-10-12 16:22:35
Document Modified: 2017-10-12 16:22:35
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC