Test Report part 24

FCC ID: NM8PL01210

Test Report

Download: PDF
FCCID_1756550

FCC TEST REPORT (PART 24) REPORT NO.: RF120522C28-1 MODEL NO.: PL01210 FCC ID: NM8PL01210 RECEIVED: May 22, 2012 TESTED: Jun. 07 ~ Jul. 12, 2012 ISSUED: Jul. 12, 2012 APPLICANT: HTC Corporation ADDRESS: No. 23, Xinghua Rd., Taoyuan City, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF120522C28-1 1 of 29 Report Format Version 5.0.0

TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................. 3 1 CERTIFICATION ........................................................................................................ 4 2 SUMMARY OF TEST RESULTS................................................................................. 5 2.1 MEASUREMENT UNCERTAINTY .............................................................................. 5 2.2 TEST SITE AND INSTRUMENTS ............................................................................... 6 3 GENERAL INFORMATION ......................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ........................................................................... 7 3.2 CONFIGURATION OF SYSTEM UNDER TEST ......................................................... 8 3.3 DESCRIPTION OF SUPPORT UNITS ........................................................................ 9 3.4 TEST ITEM AND TEST CONFIGURATION .............................................................. 10 3.5 EUT OPERATING CONDITIONS.............................................................................. 11 3.6 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................... 11 4 TEST TYPES AND RESULTS................................................................................... 12 4.1 OUTPUT POWER MEASUREMENT ........................................................................ 12 4.1.1 LIMITS OF OUTPUT POWER MEASUREMENT ...................................................... 12 4.1.2 TEST PROCEDURES .............................................................................................. 12 4.1.3 TEST SETUP ........................................................................................................... 13 4.1.4 TEST RESULTS ....................................................................................................... 14 4.2 FREQUENCY STABILITY MEASUREMENT ............................................................ 15 4.2.1 LIMITS OF FREQUENCY STABILIITY MEASUREMENT ......................................... 15 4.2.2 TEST PROCEDURE ................................................................................................. 15 4.2.3 TEST SETUP ........................................................................................................... 15 4.2.4 TEST RESULTS ....................................................................................................... 16 4.3 OCCUPIED BANDWIDTH MEASUREMENT ............................................................ 17 4.3.1 TEST PROCEDURES .............................................................................................. 17 4.3.2 TEST SETUP ........................................................................................................... 17 4.3.3 TEST RESULTS ....................................................................................................... 18 4.4 BAND EDGE MEASUREMENT ................................................................................ 19 4.4.1 LIMITS OF BAND EDGE MEASUREMENT .............................................................. 19 4.4.2 TEST SETUP ........................................................................................................... 19 4.4.3 TEST PROCEDURES .............................................................................................. 19 4.4.4 TEST RESULTS ....................................................................................................... 20 4.5 CONDUCTED SPURIOUS EMISSIONS ................................................................... 21 4.5.1 LIMITS OF CONDUCTED SPURIOUS EMISSIONS MEASUREMENT .................... 21 4.5.2 TEST PROCEDURE ................................................................................................. 21 4.5.3 TEST SETUP ........................................................................................................... 21 4.5.4 TEST RESULTS ....................................................................................................... 22 4.6 RADIATED EMISSION MEASUREMENT ................................................................. 23 4.6.1 LIMITS OF RADIATED EMISSION MEASUREMENT ............................................... 23 4.6.2 TEST PROCEDURES .............................................................................................. 23 4.6.3 DEVIATION FROM TEST STANDARD ..................................................................... 23 4.6.4 TEST SETUP ........................................................................................................... 24 4.6.5 TEST RESULTS ....................................................................................................... 25 5 PHOTOGRAPHS OF THE TEST CONFIGURATION ................................................ 27 6 INFORMATION ON THE TESTING LABORATORIES .............................................. 28 7 APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ............................................................................................. 29 Report No.: RF120522C28-1 2 of 29 Report Format Version 5.0.0

RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF120522C28-1 Original release Jul. 12, 2012 Report No.: RF120522C28-1 3 of 29 Report Format Version 5.0.0

1 CERTIFICATION PRODUCT: Smartphone MODEL: PL01210 BRAND: HTC APPLICANT: HTC Corporation TESTED: Jun. 07 ~ Jul. 12, 2012 TEST SAMPLE: Production Unit STANDARDS: FCC Part 24, Subpart E The above equipment (model: PL01210) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE : Jul. 12, 2012 Ivonne Wu / Senior Specialist APPROVED BY : , DATE : Jul. 12, 2012 Gary Chang / Technical Manager Report No.: RF120522C28-1 4 of 29 Report Format Version 5.0.0

2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 24 & Part 2 STANDARD TEST TYPE RESULT REMARK SECTION 2.1046 Equivalent isotropically radiated PASS Meet the requirement of limit. 24.232 power 2.1055 Frequency Stability PASS Meet the requirement of limit. 24.235 2.1049 Occupied Bandwidth PASS Meet the requirement of limit. 24.238(b) 24.238(b) Band Edge Measurements PASS Meet the requirement of limit. 2.1051 Conducted Spurious Emissions PASS Meet the requirement of limit. 24.238 Meet the requirement of limit. 2.1053 Radiated Spurious Emissions PASS Minimum passing margin is 24.238 -22.53dB at 3760.00MHz. 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: MEASUREMENT FREQUENCY UNCERTAINTY Conducted emissions 150kHz~30MHz 2.44 dB 30MHz ~ 200MHz 2.93 dB 200MHz ~1000MHz 2.95 dB Radiated emissions 1GHz ~ 18GHz 2.26 dB 18GHz ~ 40GHz 1.94 dB This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Report No.: RF120522C28-1 5 of 29 Report Format Version 5.0.0

2.2 TEST SITE AND INSTRUMENTS DESCRIPTION & DATE OF DUE DATE OF MODEL NO. SERIAL NO. MANUFACTURER CALIBRATION CALIBRATION Test Receiver N9038A MY51210203 Dec. 22, 2011 Dec. 21, 2012 Agilent Spectrum Analyzer FSU43 101261 Dec. 21, 2011 Dec. 20, 2012 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-472 Dec. 20, 2011 Dec. 19, 2012 SCHWARZBECK HORN Antenna BBHA 9120 D 9120D-969 Dec. 20, 2011 Dec. 19, 2012 SCHWARZBECK ORN Antenna BBHA 9170 9170-480 Dec. 20, 2011 Dec. 19, 2012 SCHWARZBECK Loop Antenna HFH2-Z2 100070 Jan. 31, 2012 Jan. 30, 2014 Preamplifier EMC 012645 980115 Dec. 30, 2011 Dec. 29, 2012 EMCI Preamplifier EMC 330H 980112 Dec. 30, 2011 Dec. 29, 2012 EMCI RF signal cable SUCOFLEX 104 309219/4 Oct. 21, 2011 Oct. 20, 2012 HUBER+SUHNNER RF signal cable SUCOFLEX 104 250130/4 Jan. 02, 2012 Jan. 01, 2013 HUBER+SUHNNER RF signal cable RG-213 NA Jan. 02, 2012 Jan. 01, 2013 Worken E3 Software NA NA NA 6.120103 Antenna Tower MFA-440H NA NA NA MF Turn Table MFT-201SS NA NA NA MF Antenna Tower &Turn Table Controller MF-7802 NA NA NA MF JFW 20dB attenuation 50HF-020-SMA NA NA NA Communications 8960 Series 10 MY50260642 Oct. 25, 2011 Oct. 24, 2012 Tester-Wireless Radio Communication MT8820C 6201010284 Aug. 01, 2011 Jul. 31, 2012 Analyzer NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 9. 3. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Site Registration No. is 460141. 5. The IC Site Registration No. is IC 7450F-4. Report No.: RF120522C28-1 6 of 29 Report Format Version 5.0.0

3 GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT EUT Smartphone MODEL NO. PL01210 5.0Vdc (adapter) POWER SUPPLY 3.7Vdc (battery) MODULATION TYPE QPSK, OQPSK, HPSK FREQUENCY RANGE 1851.25MHz ~ 1908.75MHz MAX. EIRP POWER 0.23Watts ANTENNA TYPE Fixed Internalantenna with -1dBi gain I/O PORTS Refer to users’ manual DATA CABLE Refer to NOTE as below ACCESSORY DEVICES Refer to NOTE as below NOTE: 1. The EUT’s accessories list refers to EUT photo. 2. The above EUT information was declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF120522C28-1 7 of 29 Report Format Version 5.0.0

3.2 CONFIGURATION OF SYSTEM UNDER TEST FOR RADIATION EMISSION TEST _9 Earphone (Powered from AC Adapter) Test table PH 5 Communications Tester—Wireless *Kept in a remote area FOR E.L.R.P. TEST EUT (Powered from battery) Py Test table $ Communications Tester—Wireless *Kept in a remote area Report No.: RF120522C28—1 8 of 29 Report Format Version 5.0.0

3.3 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. FOR EMISSION TEST NO. PRODUCT BRAND MODEL NO. SERIAL NO. FCC ID 1 EARPHONE Cotron HS $250 NA NA NO. SIGNAL CABLE DESCRIPTION OF THE ABOVE SUPPORT UNITS 1_JNA NOTE: 1. All power cords of the above support units are non shielded (1.8m). 2. Item 1 was provided by client. Report No.: RF120522C28—1 9 of 29 Report Format Version 5.0.0

3.4 TEST ITEM AND TEST CONFIGURATION Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates, XYZ axis and antenna ports The worst case was found when positioned on Y-plane for ERP and Y-axis for radiated emission. Following channel(s) was (were) selected for the final test as listed below: EUT CONFIGURE TEST ITEM AVAILABLE CHANNEL TESTED CHANNEL MODE MODE - EIRP 25 to 1175 25, 600, 1175 RC3+SO55 - FREQUENCY STABILITY 25 to 1175 600 RC3+SO55 - OCCUPIED BANDWIDTH 25 to 1175 25, 600, 1175 RC3+SO55 - BAND EDGE 25 to 1175 25, 1175 RC3+SO55 - CONDCUDETED EMISSION 25 to 1175 600 RC3+SO55 - RADIATED EMISSION 25 to 1175 600 RC3+SO55 - RADIATED EMISSION 25 to 1175 600 RC3+SO55 TEST CONDITION: TEST ITEM ENVIRONMENTAL CONDITIONS INPUT POWER TESTED BY EIRP 25deg. C, 65%RH 3.7Vdc Phoenix Chen FREQUENCY STABILITY 25deg. C, 65%RH 3.7Vdc Phoenix Chen OCCUPIED BANDWIDTH 25deg. C, 65%RH 3.7Vdc Phoenix Chen BAND EDGE 25deg. C, 65%RH 3.7Vdc Phoenix Chen CONDCUDETED EMISSION 25deg. C, 65%RH 3.7Vdc Phoenix Chen RADIATED EMISSION 25deg. C, 65%RH 120Vac, 60Hz Kay Wu Report No.: RF120522C28-1 10 of 29 Report Format Version 5.0.0

3.5 EUT OPERATING CONDITIONS The EUT makes a call to the communication simulator. The communication simulator station system controlled a EUT to export maximum output power under transmission mode and specific channel frequency 3.6 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC 47 CFR Part 2 FCC 47 CFR Part 24 ANSI/TIA/EIA-603-C 2004 NOTE: All test items have been performed and recorded as per the above standards. Report No.: RF120522C28-1 11 of 29 Report Format Version 5.0.0

4 TEST TYPES AND RESULTS 4.1 OUTPUT POWER MEASUREMENT 4.1.1 LIMITS OF QOUTPUT POWER MEASUREMENT Mobile and portable stations are limited to 2 watts EIRP 4.1.2 TEST PROCEDURES EIRP MEASUREMENT: a. All measurements were done at low, middle and high operational frequency range. RWB and VBW is SMHz for CDMA mode. b. Substitution method is used for E.LR.P measurement. In the semi—anechoic chamber, EUT placed on the 0.8m height of Turn Table, rotated the table around 360 degrees to search the maximum radiation power and receiver antenna shall be rotated vertical and horizontal polarization and moved height from 1m to 4m to find the maximum polar radiated power. The "Read Value" is the spectrum reading the maximum power value. c. The substitution horn antenna is substituted for EUT at the same position and signals generator export the CW signal to the substitution antenna via a tx cable. Rotated the Turn Table and moved receiving antenna to find the maximum radiation power. Adjust output power level of S.G to get a Value of spectrum reading equal to "Read Value" of step b. Record the power level of S.G d. EIRP = Output power level of S.G — TX cable loss + Antenna gain of substitution horn. CONDUCTED POWER MEASUREMENT: The EUT was set up for the maximum power with CDMA link data modulation and link up with simulator. Set the EUT to transmit under low, middle and high channel and record the power level shown on simulator. Report No.: RF120522C28—1 12 of 29 Report Format Version 5.0.0

4.1.3 TEST SETUP EIRP MEASUREMENT: 1~4m 3m For the actual test configuration, please refer to the attached file (Test Setup Photo). CONDUCTED POWER MEASUREMENT: COMMUNICATION EUT SIMULATOR For the actual test configuration, please refer to the attached file (Test Setup Photo). Report No.: RF120522C28-1 13 of 29 Report Format Version 5.0.0

4.1.4 TEST RESULTS CONDUCTED QOUTPUT POWER (dBm) Band CDMA2000 BCO Channel 25 600 1175 Frequency (MHz) 1851.25 1880 1908.75 RC1+S055 24.89 24.88 24.94 RC3+S5055 24.86 24.87 24.97 RC3+5032(+ F—SCH) 24.85 24.86 24.92 RC3+S5032(+SCH) 24.82 24.85 24.92 RTAP 153.6 24.96 24.93 24.96 RETAP 4096 24.95 24.90 24.95 EIRP POWER (dBm) FOR 1xRTT RC3+S055 MODE Frequency LVL Correction Polarization Plane Channel (MH2z) (dBm) Factor(dB) EIRP(dBm) EIRP(W) (Hv) 25 1851.25 —24.20 38.19 13.99 0.03 H 600 1880.00 —24.07 38.70 14.63 0.03 1175 1908.75 —24.73 39.35 14.62 0.03 H Y 25 1851.25 —14.82 38.48 23.66 0.23 V 600 1880.00 —15.22 38.59 23.37 0.22 V 1175 1908.75 —15.95 38.87 22.92 0.20 V Report No.: RF120522C28—1 14 of 29 Report Format Version 5.0.0

4.2 FREQUENCY STABILITY MEASUREMENT 4.2.1 LIMITS OF FREQUENCY STABILIITY MEASUREMENT The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. 4.2.2 TEST PROCEDURE a. Device is placed at the oven room. The oven room could control the temperatures and humidity. Power warm up is at least 15 min and power applied should perform before recording frequency error. b. EUT is connected the external power supply to control the DC input power. The test voltage range is from minimum to maximum working voltage. Each step shall be record the frequency error rate. c. The temperature range step is 10 degrees in this test items. All temperature levels shall be hold the £0.5°C during the measurement testing. The each temperature step shall be at least 0.5 hours, consider the EUT could be test under the stability condition. NOTE: The frequency error was recorded frequency error from the communication simulator. 4.2.3 TEST SETUP COMMUNICATION OvEN ROOM SIMULATOR ANTENNA EXTERNAL POWER SOURCE EUT DC POWER SUPPLY Report No.: RF120522C28—1 15 of 29 Report Format Version 5.0.0

4.2.4 TEST RESULTS 1xRTT RC3+S055 MODE FREQUENCY ERROR VS. VOLTAGE VOLTAGE (Volts) FREQUENCY ERROR (ppm) LIMIT (ppm) 3.8 —0.002 25 3.6 —0.002 25 4.2 —0.002 25 NOTE: The applicant defined the normal working voltage of the battery is from 3.6Vdc to 4.2Vdc. FREQUENCY ERROR vs. TEMPERATURE. TEMP. (‘C) FREQUENCY ERROR (ppm) LIMIT (ppm) —10 —0.002 2.5 0 —0.002 2.5 10 —0.002 2.5 20 —0.002 2.5 30 —0.002 2.5 40 —0.002 2.5 50 —0.002 2.5 55 —0.002 2.5 Report No.: RF120522C28—1 16 of 29 Report Format Version 5.0.0

4.3 OCCUPIED BANDWIDTH MEASUREMENT 4.3.1 TEST PROCEDURES The EUT makes a call to the communication simulator. All measurements were done at low, middle and high operational frequency range. The communication simulator station system controlled a EUT to export maximum output power under transmission mode and specific channel frequency. Use OBW measurement function of Spectrum analyzer to measure 99 % occupied bandwidth. 4.3.2 TEST SETUP COMMUNICATION SIMULATOR POWER SPLITTER SPECTRUM ANALYZER 10dB ATTENUATION PAD EUT Report No.: RF120522C28-1 17 of 29 Report Format Version 5.0.0

4.3.3 TEST RESULTS 1xRTT RC3+SO55 MODE FREQUENCY 99% OCCUPIED 26dB BANDWIDTH CHANNEL (MHz) BANDWIDTH (MHz) (MHz) 25 1851.25 1.272 1.419 600 1880 1.273 1.423 1175 1908.75 1.272 1.421 SPECTRUM PLOT OF WORST VALUE Report No.: RF120522C28-1 18 of 29 Report Format Version 5.0.0

4.4 BAND EDGE MEASUREMENT 4.4.1 LIMITS OF BAND EDGE MEASUREMENT Power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. In the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. 4.4.2 TEST SETUP COMMUNICATION SIMULATOR POWER SPLITTER SPECTRUM ANALYZER 10dB ATTENUATION PAD EUT 4.4.3 TEST PROCEDURES a. All measurements were done at low and high operational frequency range. b. The center frequency of spectrum is the band edge frequency and span is 3 MHz. RB of the spectrum is 13kHz and VB of the spectrum is 51kHz. c. Record the max trace plot into the test report. Report No.: RF120522C28-1 19 of 29 Report Format Version 5.0.0

4.4.4 TEST RESULTS 1xRTT RC3+SO55 CHANNEL 25 CHANNEL 1175 Report No.: RF120522C28-1 20 of 29 Report Format Version 5.0.0

4.5 CONDUCTED SPURIOUS EMISSIONS 4.5.1 LIMITS OF CONDUCTED SPURIOUS EMISSIONS MEASUREMENT The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. The emission limit equal to –13dBm. 4.5.2 TEST PROCEDURE a. The EUT makes a phone call to the communication simulator. All measurements were done at low, middle and high operational frequency range. b. Measuring frequency range is from 30MHz to 19.1GHz. 10dB attenuation pad is connected with spectrum. RBW=1MHz and VBW=3MHz is used for conducted emission measurement. 4.5.3 TEST SETUP COMMUNICATION SIMULATOR POWER SPLITTER SPECTRUM ANALYZER 10dB ATTENUATION PAD EUT Report No.: RF120522C28-1 21 of 29 Report Format Version 5.0.0

4.5.4 TEST RESULTS 1xRTT RC3+SO55 CHANNEL 600 FREQUENCY RANGE : 30MHz~7GHz FREQUENCY RANGE : 7GHz~14GHz FREQUENCY RANGE : 14GHz~19.1GHz Report No.: RF120522C28-1 22 of 29 Report Format Version 5.0.0

4.6 RADIATED EMISSION MEASUREMENT 4.6.1 LIMITS OF RADIATED EMISSION MEASUREMENT The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. The emission limit equal to —13dBm. 4.6.2 TEST PROCEDURES a. Substitution method is used for E.L.R.P measurement. In the semi—anechoic chamber, EUT placed on the 0.8m height of Turn Table, rotated the table around 360 degrees to search the maximum radiation power and receiver antenna shall be rotated vertical and horizontal polarization and moved height from 1m to 4m to find the maximum polar radiated power. The "Read Value" is the spectrum reading the maximum power value. b. The substitution horn antenna is substituted for EUT at the same position and signals generator export the CW signal to the substitution antenna via a TX cable. Rotated the Turn Table and moved receiving antenna to find the maximum radiation power. Adjust output power level of S.G to get a Value of spectrum reading equal to "Read Value" of step a. Record the power level of S.G c. EIRP = Output power level of S.G — TX cable loss + Antenna gain of substitution horn. d. E.R.P power can be calculated form E.1.R.P power by subtracting the gain of dipole, E.R.P power = E.1.P.R power — 2.150Bi. NOTE: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 1MHz/3MHz. 4.6.3 DEVIATION FROM TEST STANDARD No deviation Report No.: RF120522C28—1 23 of 29 Report Format Version 5.0.0

4.6.4 TEST SETUP For the actual test configuration, please refer to the attached file (Test Setup Photo). Report No.: RF120522C28-1 24 of 29 Report Format Version 5.0.0

4.6.5 TEST RESULTS 1xRTT RC3+SO55 Report No.: RF120522C28-1 25 of 29 Report Format Version 5.0.0

Bureau Veritas Consumer Products Services Ltd., Taoyuan Branch Data: 16 Level (dBmim) Date: 2012—06—14 10 PART2224 64B —20 —30) 40 T —50 —60 B —70) B 301000. 3000. 5000. 7000. 2000 11000. 13000. 15000. 17000. 19000 Frequency (MHz) Site : 966 Chamber 5 Condition PART22/24 3m EIRP_RSE_1G~19G_3 VERTICAL Brand/Model: PLO1210 Remark : 1XRTT1900 Link Tested by Kay Wu Temprature : 25°C Humidity 65% Plane 1¥ Read Limit Over Freq Level Level Line Limit Factor Remark MHz dBm/m dBm dBm/m dB dB/m 1 35.67 —44.84 —42.48 —13.00 —31.84 —2.36 Peak 2 42.96 —43.95 —42.62 —13.00 —30.95 —1.33 Peak 3 139.62 —68.88 —63.21 —13.00 —55.88 —5.67 Peak 4 607.30 —64.64 —64.41 —13.00 —51.64 —0.23 Peak 5 671.70 —63.04 —63.98 —13.00 —50.04 0.94 Peak 6 716.50 —62.75 —64.31 —13.00 —49.75 1.56 Peak 7 pp 3760.00 —41.65 —34.92 —13.00 —28.65 —6.73 Peak

5 PHOTOGRAPHS OF THE TEST CONFIGURATION Please refer to the attached file (Test Setup Photo). Report No.: RF120522C28-1 27 of 29 Report Format Version 5.0.0

6 INFORMATION ON THE TESTING LABORATORIES We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety/Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report No.: RF120522C28-1 28 of 29 Report Format Version 5.0.0

7 APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No any modifications were made to the EUT by the lab during the test. ---END--- Report No.: RF120522C28-1 29 of 29 Report Format Version 5.0.0


Document Created: 2012-07-26 15:47:02
Document Modified: 2012-07-26 15:47:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC