RF Test Report

FCC ID: NM82PYV100

Test Report

Download: PDF
FCCID_3265233

FCC Test Report Report No.: RF161027C16 FCC ID: NM82PYV100 Test Model: 2PYV100 Received Date: Oct. 27, 2016 Test Date: Dec. 15, 2016 ~ Dec. 19, 2016 Issued Date: Jan. 03, 2017 Applicant: HTC Corporation Address: 1F, 6-3 Baoqiang Road, Xindian District, New Taipei City 231, Taiwan Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) Test Location (1): No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. Test Location (2): No.215, Sec. 3, Beixin Rd., Xindian Dist., New Taipei City 231, Taiwan, R.O.C This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF161027C16 Page No. 1 / 25 Report Format Version: 6.1.1

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ........................................................................................................................... 4 2 Summary of Test Results ........................................................................................................................... 5 2.1 Measurement Uncertainty ..................................................................................................................... 5 2.2 Modification Record .............................................................................................................................. 5 3 General Information ................................................................................................................................... 6 3.1 General Description of EUT .................................................................................................................. 6 3.2 Description of Test Modes..................................................................................................................... 6 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................... 7 3.3 Description of Support Units ................................................................................................................. 8 3.3.1 Configuration of System under Test ........................................................................................... 8 3.4 General Description of Applied Standards ............................................................................................ 8 4 Test Types and Results .............................................................................................................................. 9 4.1 Radiated Emission and Bandedge Measurement ................................................................................ 9 4.1.1 Limits of Radiated Emission and Bandedge Measurement ....................................................... 9 4.1.2 Test Instruments ....................................................................................................................... 10 4.1.3 Test Procedures ......................................................................................................................... 11 4.1.4 Deviation from Test Standard .................................................................................................... 11 4.1.5 Test Set Up ............................................................................................................................... 12 4.1.6 EUT Operating Conditions ........................................................................................................ 12 4.1.7 Test Results .............................................................................................................................. 13 4.2 Conducted Emission Measurement .................................................................................................... 17 4.2.1 Limits of Conducted Emission Measurement ........................................................................... 17 4.2.2 Test Instruments ....................................................................................................................... 17 4.2.3 Test Procedures ........................................................................................................................ 18 4.2.4 Deviation from Test Standard ................................................................................................... 18 4.2.5 Test Setup ................................................................................................................................. 18 4.2.6 EUT Operating Conditions ........................................................................................................ 18 4.2.7 Test Results .............................................................................................................................. 19 4.3 20 dB Bandwidth ................................................................................................................................. 21 4.3.1 Limits of 20 dB Bandwidth Measurement ................................................................................. 21 4.3.2 Test Setup ................................................................................................................................. 21 4.3.3 Test Instruments ....................................................................................................................... 21 4.3.4 Test Procedures ........................................................................................................................ 21 4.3.5 Deviation from Test Standard ................................................................................................... 21 4.3.6 EUT Operating Conditions ........................................................................................................ 21 4.3.7 Test Results .............................................................................................................................. 22 4.4 Antenna Requirement ......................................................................................................................... 23 4.4.1 Standard Requirement ............................................................................................................. 23 4.5 EUT Antenna ....................................................................................................................................... 23 5 Pictures of Test Arrangements................................................................................................................ 24 Appendix – Information on the Testing Laboratories ................................................................................ 25 Report No.: RF161027C16 Page No. 2 / 25 Report Format Version: 6.1.1

Release Control Record Issue No. Description Date Issued RF161027C16 Original Release Jan. 03, 2017 Report No.: RF161027C16 Page No. 3 / 25 Report Format Version: 6.1.1

1 Certificate of Conformity Product: Tracker Brand: HTC Test Model: 2PYV100 Sample Status: Identical Prototype Applicant: HTC Corporation Test Date: Dec. 15, 2016 ~ Dec. 19, 2016 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.249) ANSI C63.10: 2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: Jan. 03, 2017 Vera Huang / Specialist Approved by : , Date: Jan. 03, 2017 Stanley Wu / Assistant Manager Report No.: RF161027C16 Page No. 4 / 25 Report Format Version: 6.1.1

2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (SECTION 15.249) FCC Test Item Result Remarks Clause 15.203 Antenna requirement PASS N/A Meet the requirement oflimit. 15.207 AC Power Conducted Emission PASS Minimum passing margin is —8.12 dB at 0.55998 MHz. 15.215 (c) 200B Bandwidth PASS Meet the requirement oflimit. Radiated Emission Test 15.209 Band Edge Measurement Meet the requirement oflimit. 15.249 Lifnfm:jodB Ieslsfthan the peak value PASS Minimum passing margin is of fundamental frequency or meet _ 15.249 (d) radiated emission limit in section 1.13 dB at 2402 MHz. 15.209 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16—4—2: M T F Expended Uncertainty easuremen requenc quency (k=2) (1) Conducted Emissions at mains ports 150 kHz ~ 30 MHz 2.44 dB 30 MHz ~ 200 MHz 2.0153 dB Radiated Emissions up to 1 GHz 200 MHz ~1000 MHz 2.0224 dB 1 GHz ~ 18 GHz 1.0121 dB Radiated Emissions above 1 GHz 18 GHz ~ 40 GHz 1.1508 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF161027G16 Page No. 5 / 25 Report Format Version: 6.1.1

3 General Information 3.1 General Description of EUT Product Tracker Brand HTC Test Model 2PYV100 Status of EUT Identical Prototype 5.0 Vdc (adapter or host equipment) Power Supply Rating 3.85 Vdc (Li-ion battery) Modulation Type GFSK Operating Frequency 2402 ~ 2480 MHz Number of Channel 40 Antenna Type PIFA antenna with -1.55 dBi gain Antenna Connector N/A Accessory Device Refer to Note as below Data Cable Supplied Refer to Note as below Note: 1. The EUT’s accessories list refers to Ext. Pho. 2. The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or user's manual. 3.2 Description of Test Modes 40 channels are provided to this EUT: Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) Channel Freq. (MHz) 0 2402 10 2422 20 2442 30 2462 1 2404 11 2424 21 2444 31 2464 2 2406 12 2426 22 2446 32 2466 3 2408 13 2428 23 2448 33 2468 4 2410 14 2430 24 2450 34 2470 5 2412 15 2432 25 2452 35 2472 6 2414 16 2434 26 2454 36 2474 7 2416 17 2436 27 2456 37 2476 8 2418 18 2438 28 2458 38 2478 9 2420 19 2440 29 2460 39 2480 Report No.: RF161027C16 Page No. 6 / 25 Report Format Version: 6.1.1

3.2.1 Test Mode Applicability and Tested Channel Detail EUT Configure Applicable To Description Mode RE1G RE<1G PLC - √ √ √ - RE1G: Radiated Emission above 1 GHz & Where RE<1G: Radiated Emission below 1 GHz Bandedge Measurement PLC: Power Line Conducted Emission NOTE: The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on Z-plane. Radiated Emission Test (Above 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Available Channel Tested Channel Modulation Type - 0 to 39 0, 19, 39 GFSK Radiated Emission Test (Below 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Tested Channel Modulation Technology Modulation Type - 0 to 39 0 GFSK Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Tested Channel Modulation Technology Modulation Type - 0 to 39 0 GFSK Test Condition: Applicable To Environmental Conditions Input Power Tested By RE1G 25 deg. C, 65 % RH 120 Vac, 60 Hz Gavin Wu RE<1G 25 deg. C, 65 % RH 120 Vac, 60 Hz Gavin Wu PLC 25 deg. C, 68 % RH 120 Vac, 60 Hz Toby Tian Report No.: RF161027C16 Page No. 7 / 25 Report Format Version: 6.1.1

3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. 3.3.1 Configuration of System under Test Q_ $$ EUT (Power from AC Adapter) *Test Table 3.4 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.249) ANSI C63.10—2013 All test items have been performed and recorded as per the above standards. NOTE: The EUT has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF161027G16 Page No. 8 / 25 Report Format Version: 6.1.1

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement The field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following Field Strength of Fundamental Field Strength of Harmonics Fundamental Frequency (millivolts/meter) (microvolts/meter) 902 ~ 928 MHz 50 500 2400 ~ 2483.5 MHz 50 500 5725 ~ 5875 MHz 50 500 24 ~ 24.25 GHz 250 2500 Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits as below table, whichever is the lesser attenuation Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000 MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF161027C16 Page No. 9 / 25 Report Format Version: 6.1.1

4.1.2 Test Instruments Description & Due Date of Model No. Serial No. Date of Calibration Manufacturer Calibration Test receiver N9038a My51210203 Jan. 21, 2016 Jan. 20, 2017 Agilent Spectrum analyzer N9010a My56070348 Sep. 02, 2016 Sep. 01, 2017 Agilent BILOG Antenna VULB9168 9168-472 Jan. 07, 2016 Jan. 06, 2017 SCHWARZBECK HORN Antenna BBHA 9120 D 9120D-969 Jan. 04, 2016 Jan. 03, 2017 SCHWARZBECK HORN Antenna BBHA 9170 9170-480 Jan. 08, 2016 Jan. 07, 2017 SCHWARZBECK Fixed Attenuator BW-N10W5+ NA Jul. 08, 2016 Jul. 07, 2017 Mini-Circuits Loop Antenna EM-6879 269 Aug. 11, 2016 Aug. 10, 2017 Preamplifier EMC 012645 980115 Oct. 21, 2016 Oct. 20, 2017 EMCI Preamplifier EMC 184045 980116 Oct. 21, 2016 Oct. 20, 2017 EMCI Preamplifier EMC 330H 980112 Oct. 21, 2016 Oct. 20, 2017 EMCI RF signal cable 309219/4 SUCOFLEX 104 Oct. 21, 2016 Oct. 20, 2017 HUBER+SUHNNER 2950114 RF signal cable SUCOFLEX 104 250130/4 Oct. 21, 2016 Oct. 20, 2017 HUBER+SUHNNER RF Coaxial Cable 8D-FB Cable-Ch10-01 Oct. 21, 2016 Oct. 20, 2017 Worken Software E3 NA NA NA BV ADT 6.120103 Antenna Tower MFA-440H NA NA NA MF Turn Table MFT-201SS NA NA NA MF Antenna Tower &Turn Table Controller MF-7802 NA NA NA MF Fixed Attenuator BW-N10W5+ NA Jul. 08, 2016 Jul. 07, 2017 Mini-Circuits Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HsinTien Chamber 1. 3. The horn antenna and preamplifier (model: 83017A) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Site Registration No. is 149147. 5. The IC Site Registration No. is IC7450I-1. Report No.: RF161027C16 Page No. 10 / 25 Report Format Version: 6.1.1

4.1.3 Test Procedures a. The EUT was placed on the top of a rotating table 0.8 meters (for below 1 GHz) / 1.5 meters (for above 1 GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120 kHz for Quasi-peak detection (QP) at frequency below 1 GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1 GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for RMS Average (Duty cycle < 98 %) for Average detection (AV) at frequency above 1 GHz, then the measurement results was added to a correction factor (10 log(1/duty cycle)). 4. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 10 Hz (Duty cycle ≥ 98 %) for Average detection (AV) at frequency above 1 GHz. 5. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF161027C16 Page No. 11 / 25 Report Format Version: 6.1.1

4.1.5 Test Set Up <Frequency Range below 1 GHz> Ant. Tower 1-4m Variable 3m 10m EUT& Support Units Turn Table 80cm Ground Plane Test Receiver <Frequency Range above 1 GHz> Ant. Tower 1-4m Variable EUT& 3m Support Units Turn Table Absorber 150cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF161027C16 Page No. 12 / 25 Report Format Version: 6.1.1

4.1.7 Test Results Above 1 GHz WORST-CASE DATA: EUT Test Condition Measurement Detail Channel Channel 0 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Gavin Wu Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2372.46 45.92 52.49 54 -8.08 26.86 4.07 37.5 124 165 Average 2372.46 60.57 67.14 74 -13.43 26.86 4.07 37.5 124 165 Peak 2402 92.87 99.39 94 -1.13 26.91 4.09 37.52 124 165 Average 2402 93.44 99.96 114 -20.56 26.91 4.09 37.52 124 165 Peak 4804 35.75 51.09 54 -18.25 30.97 6.79 53.1 103 206 Average 4804 44.91 60.25 74 -29.09 30.97 6.79 53.1 103 206 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2372.46 39.94 46.51 54 -14.06 26.86 4.07 37.5 115 321 Average 2382.45 57.25 63.81 74 -16.75 26.86 4.08 37.5 115 321 Peak 2402 90.39 96.91 94 -3.61 26.91 4.09 37.52 115 321 Average 2402 90.93 97.45 114 -23.07 26.91 4.09 37.52 115 321 Peak 4804 35.98 51.32 54 -18.02 30.97 6.79 53.1 109 162 Average 4804 45.77 61.11 74 -28.23 30.97 6.79 53.1 109 162 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value Report No.: RF161027C16 Page No. 13 / 25 Report Format Version: 6.1.1

EUT Test Condition Measurement Detail Channel Channel 19 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Gavin Wu Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2371.74 37.09 43.66 54 -16.91 26.86 4.07 37.5 105 154 Average 2380.38 57.69 64.25 74 -16.31 26.86 4.08 37.5 105 154 Peak 2440 92.52 98.8 94 -1.48 27.06 4.12 37.46 105 154 Average 2440 93.28 99.56 114 -20.72 27.06 4.12 37.46 105 154 Peak 2494.52 47.63 53.52 54 -6.37 27.2 4.16 37.25 105 154 Average 2494.72 61.5 67.39 74 -12.5 27.2 4.16 37.25 105 154 Peak 4880 35.06 50.2 54 -18.94 31.06 6.85 53.05 104 145 Average 4880 44.27 59.41 74 -29.73 31.06 6.85 53.05 104 145 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2315.76 57.26 64.03 74 -16.74 26.67 4.03 37.47 100 320 Peak 2386.41 37.34 43.85 54 -16.66 26.91 4.08 37.5 100 320 Average 2440 91.14 97.42 94 -2.86 27.06 4.12 37.46 100 320 Average 2440 91.63 97.91 114 -22.37 27.06 4.12 37.46 100 320 Peak 2494.6 43.18 49.07 54 -10.82 27.2 4.16 37.25 100 320 Average 2494.76 59.15 65.04 74 -14.85 27.2 4.16 37.25 100 320 Peak 4880 35.66 50.8 54 -18.34 31.06 6.85 53.05 100 201 Average 4880 44.76 59.9 74 -29.24 31.06 6.85 53.05 100 201 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value Report No.: RF161027C16 Page No. 14 / 25 Report Format Version: 6.1.1

EUT Test Condition Measurement Detail Channel Channel 39 Frequency Range 1 GHz ~ 25 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Average (AV) Environmental 25 deg. C, 65 % RH Tested By Gavin Wu Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2480 92.83 98.85 94 -1.17 27.15 4.15 37.32 105 157 Average 2480 93.32 99.34 114 -20.68 27.15 4.15 37.32 105 157 Peak 2494.44 62.2 68.09 74 -11.8 27.2 4.16 37.25 105 157 Peak 2494.52 50.43 56.32 54 -3.57 27.2 4.16 37.25 105 157 Average 4960 36.12 51.09 54 -17.88 31.16 6.91 53.04 106 129 Average 4960 44.78 59.75 74 -29.22 31.16 6.91 53.04 106 129 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 2480 90.22 96.24 94 -3.78 27.15 4.15 37.32 100 346 Average 2480 90.83 96.85 114 -23.17 27.15 4.15 37.32 100 346 Peak 2494.92 44.83 50.72 54 -9.17 27.2 4.16 37.25 100 346 Average 2495.04 58.91 64.8 74 -15.09 27.2 4.16 37.25 100 346 Peak 4960 36.26 51.23 54 -17.74 31.16 6.91 53.04 105 120 Average 4960 45.69 60.66 74 -28.31 31.16 6.91 53.04 105 120 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value Report No.: RF161027C16 Page No. 15 / 25 Report Format Version: 6.1.1

9 kHz ~ 30 MHz DATA: The amplitude of spurious emissions attenuated more than 20 dB below the permissible value is not required to be report. Below 1 GHz WORST-CASE DATA: EUT Test Condition Measurement Detail Channel Channel 0 Frequency Range 30 MHz ~ 1 GHz Peak (PK) Input Power 120 Vac, 60 Hz Detector Function Quasi-peak (QP) Environmental 25 deg. C, 65 % RH Tested By Gavin Wu Conditions Antennal Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 76.56 27.78 49.44 40 -12.22 9.09 0.87 31.62 107 119 Peak 191.99 28.08 48.59 43.5 -15.42 9.91 1.27 31.69 134 269 Peak 305.48 32.9 50.07 46 -13.1 13.08 1.65 31.9 124 359 Peak 413.15 28.2 42.68 46 -17.8 15.6 1.93 32.01 138 356 Peak 557.68 24.61 35.82 46 -21.39 18.64 2.19 32.04 116 228 Peak 799.21 32.18 38.78 46 -13.82 22.22 2.61 31.43 102 183 Peak Antennal Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 101.78 24.44 46.07 43.5 -19.06 9.25 1.06 31.94 101 62 Peak 172.59 29 48.13 43.5 -14.5 11.47 1.16 31.76 113 110 Peak 346.22 23.11 39.14 46 -22.89 14.05 1.75 31.83 106 206 Peak 488.81 27.36 39.97 46 -18.64 17.1 2.07 31.78 134 11 Peak 645.95 30.46 40 46 -15.54 20.16 2.35 32.05 137 213 Peak 799.21 30.19 36.79 46 -15.81 22.22 2.61 31.43 133 325 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level – Limit value Report No.: RF161027C16 Page No. 16 / 25 Report Format Version: 6.1.1

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 4.2.2 Test Instruments Description & Date Of Due Date Of Model No. Serial No. Manufacturer Calibration Calibration Test Receiver ESCI 100424 Oct. 24, 2016 Oct. 23, 2017 ROHDE & SCHWARZ RF signal cable (with 10dB PAD) 5D-FB Cable-cond1-01 Dec. 26, 2015 Dec. 25, 2016 Woken LISN/AMN ROHDE & SCHWARZ ESH3-Z5 835239/001 Feb. 26, 2016 Feb. 25, 2017 (EUT) LISN/AMN ROHDE & SCHWARZ ESH3-Z5 100311 Jul. 28, 2016 Jul. 27, 2017 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.3 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 1. 3. The VCCI Site Registration No. is C-2040. 4. Test Date: Dec. 16, 2016 Report No.: RF161027C16 Page No. 17 / 25 Report Format Version: 6.1.1

4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50 uH of coupling impedance for the measuring instrument. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. The frequency range from 150 kHz to 30 MHz was searched. Emission levels under (Limit — 20 dB) was not recorded. NOTE: The resolution bandwidth and video bandwidth of test receiver is 9 kHz for quasi—peak detection (QP) and average detection (AV) at frequency 0.15 MHz — 30 MHz. 4.2.4 Deviation from Test Standard No deviation. 4.2.5 Test Setup Vertical Ground Reference Plane /Test Receiver m L___] o o o o 40cm EUT __ E* 5 a o o 80cm LISN L L1 L N T \ Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT Operating Conditions Same as 4.1.6. Report No.: RF161027G16 Page No. 18 / 25 Report Format Version: 6.1.1

4.2.7 Test Results Detector Function & . Frequency Range 150kHz ~ 3OMHz Resolu}ion S:;'S;;e(i(vgog,&-/lz Bandwidth " Environmental s Input Power 120Vac, 60Hz Conditions 25°C, 65%RH Tested by Toby Tian Test Date 2016/12/16 Phase Of Power : Line (L) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.17801 10.02 22.88 9.98 82.90 20.00 64.58 54.58 —31.68 —34.58 2 0.54255 10.14 31.08 21.08 41.22 31.22 56.00 46.00 —14.78 —14.78 3 1.11400 10.21 25.36 11.88 35.57 22.09 56.00 46.00 —20.43 —23.91 4 1.47000 10.23 20.35 11.32 30.58 21.55 56.00 46.00 —25.42 —24.45 5 2.04600 10.27 19.64 8.44 29.91 18.71 56.00 46.00 —26.09 —27.29 6 2.77000 10.32 19.04 745 29.36 17.77 56.00 46.00 —26.64 —28.23 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value =aaaeaeaaufig — 0 a Report No.: RF161027G16 Page No. 19 /25 Report Format Version: 6.1.1

Detector Function & . Frequency Range 150kHz ~ 3OMHz Resolu}ion S:;'S;;e(i{(vgog,&-/lz Bandwidth " Input Power 120Vac, 60Hz Eg‘r’]';‘ii?o”r:sma' 25°C, 65%RH Tested by Toby Tian Test Date 2016/12/16 Phase Of Power : Neutral (N) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuyV) (dBuV) (dBuyV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15400 10.03 30.37 22.07 40.40 32.10 65.78 55.78 —25.38 —23.68 2 0.55998 10.15 33.99 27.73 44.14 37.88 56.00 46.00 —11.86 —8.12 3 0.93602 10.20 27.00 19.92 37.20 30.12 56.00 46.00 —18.80 —15.88 4 1.63000 10.25 26.80 19.55 37.05 29.80 56.00 46.00 —18.95 —16.20 5 2.35400 10.31 25.77 18.30 36.08 28.61 56.00 46.00 —19.92 —17.39 6 3.42600 10.39 24.02 15.72 34.41 26.11 56.00 46.00 —21.59 —19.89 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value $#B # s g 8 g s 8 B0 8 59 & Report No.: RF161027G16 Page No. 20 / 25 Report Format Version: 6.1.1

4.3 20 dB Bandwidth 4.3.1 Limits of 20 dB Bandwidth Measurement The 20 dB bandwidth shall be specified in operating frequency band. 4.3.2 Test Setup Refer to section 4.1.5. 4.3.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.3.4 Test Procedures The bandwidth of the fundamental frequency was measured by spectrum analyzer with 300 kHz RBW and 1 MHz VBW. The 20 dB bandwidth is defined as the total spectrum the power of which is higher than peak power minus 20 dB. 4.3.5 Deviation from Test Standard No deviation. 4.3.6 EUT Operating Conditions The software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel frequencies individually. Report No.: RF161027C16 Page No. 21 / 25 Report Format Version: 6.1.1

4.3.7 Test Results Frequency 20 dB Bandwidth (MHz) Channel (MHz) GFSK 0 2402 1.73 19 2440 1.72 39 2480 1.70 Spectrum Plot Of Worst Value Report No.: RF161027C16 Page No. 22 / 25 Report Format Version: 6.1.1

4.4 Antenna Requirement 4.4.1 Standard Requirement 15.203 requirement: For intentional device, according to 15.203: an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 4.5 EUT Antenna The EUT antenna is the permanent integral antenna. It comply with the standard requirement. Report No.: RF161027C16 Page No. 23 / 25 Report Format Version: 6.1.1

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF161027C16 Page No. 24 / 25 Report Format Version: 6.1.1

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF161027C16 Page No. 25 / 25 Report Format Version: 6.1.1


Document Created: 2017-12-21 02:34:12
Document Modified: 2017-12-21 02:34:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC