Test report (Part 27-b) rev1

FCC ID: NM80P4E230

Test Report

Download: PDF
FCCID_2073127

FCC TEST REPORT (PART 27) REPORT NO.: RF130722C16-3 MODEL NO.: 0P4E230 FCC ID: NM80P4E230 RECEIVED: Jul. 16, 2013 TESTED: Aug. 12, 2013 ~ Aug. 13, 2013 ISSUED: Sep. 05, 2013 APPLICANT: HTC Corporation ADDRESS: No. 23, Xinghua Rd., Taoyuan City, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF130722C16-3 1 of 30 Report Format Version 5.0.0

TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................ 4 1 CERTIFICATION ........................................................................................... 5 2 SUMMARY OF TEST RESULTS ................................................................... 6 2.1 MEASUREMENT UNCERTAINTY ................................................................ 6 2.2 TEST SITE AND INSTRUMENTS ................................................................. 7 3 GENERAL INFORMATION ........................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT.............................................................. 8 3.2 CONFIGURATION OF SYSTEM UNDER TEST ........................................... 9 3.3 DESCRIPTION OF SUPPORT UNITS .......................................................... 9 3.4 DESCRIPTION OF TEST MODES.............................................................. 10 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................. 11 4 TEST TYPES AND RESULTS ..................................................................... 12 4.1 OUTPUT POWER MEASUREMENT .......................................................... 12 4.1.1 LIMITS OF OUTPUT POWER MEASUREMENT ........................................ 12 4.1.2 TEST PROCEDURES ................................................................................. 12 4.1.3 TEST SETUP .............................................................................................. 13 4.1.4 TEST RESULTS .......................................................................................... 14 4.2 FREQUENCY STABILITY MEASUREMENT .............................................. 15 4.2.1 LIMITS OF FREQUENCY STABILIITY MEASUREMENT ........................... 15 4.2.2 TEST PROCEDURE ................................................................................... 15 4.2.3 TEST SETUP .............................................................................................. 15 4.2.4 TEST RESULTS .......................................................................................... 16 4.3 OCCUPIED BANDWIDTH MEASUREMENT .............................................. 17 4.3.1 LIMITS OF OCCUPIED BANDWIDTH MEASUREMENT ........................... 17 4.3.2 TEST SETUP .............................................................................................. 17 4.3.3 TEST PROCEDURES ................................................................................. 17 4.3.4 TEST RESULTS .......................................................................................... 18 4.4 PEAK TO AVERAGE RATIO ....................................................................... 19 4.4.1 LIMITS OF PEAK TO AVERAGE RATIO MEASUREMENT ........................ 19 4.4.2 TEST SETUP .............................................................................................. 19 4.4.3 TEST PROCEDURES ................................................................................. 19 4.4.4 TEST RESULTS .......................................................................................... 20 4.5 BAND EDGE MEASUREMENT .................................................................. 21 4.5.1 LIMITS OF BAND EDGE MEASUREMENT ................................................ 21 4.5.2 TEST SETUP .............................................................................................. 21 4.5.3 TEST PROCEDURES ................................................................................. 21 4.5.4 TEST RESULTS .......................................................................................... 22 4.6 CONDUCTED SPURIOUS EMISSIONS ..................................................... 23 4.6.1 LIMITS OF CONDUCTED SPURIOUS EMISSIONS MEASUREMENT ..... 23 4.6.2 TEST PROCEDURE ................................................................................... 23 Report No.: RF130722C16-3 2 of 30 Report Format Version 5.0.0

4.6.3 TEST SETUP .............................................................................................. 23 4.6.4 TEST RESULTS .......................................................................................... 24 4.7 RADIATED EMISSION MEASUREMENT ................................................... 25 4.7.1 LIMITS OF RADIATED EMISSION MEASUREMENT................................. 25 4.7.2 TEST PROCEDURES ................................................................................. 25 4.7.3 DEVIATION FROM TEST STANDARD ....................................................... 25 4.7.4 TEST SETUP .............................................................................................. 26 4.7.5 TEST RESULTS .......................................................................................... 27 5 INFORMATION ON THE TESTING LABORATORIES ................................ 29 6 APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ...................................................... 30 Report No.: RF130722C16-3 3 of 30 Report Format Version 5.0.0

RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF130722C16-3 Original release Sep. 05, 2013 Report No.: RF130722C16-3 4 of 30 Report Format Version 5.0.0

1 CERTIFICATION PRODUCT: Smartphone MODEL NO.: 0P4E230 BRAND: HTC APPLICANT: HTC Corporation TESTED: Aug. 12, 2013 ~ Aug. 13, 2013 TEST SAMPLE: ENGINEERING SAMPLE TEST STANDARDS: FCC Part 27, Subpart C, L FCC Part 2 ANSI C63.4-2003 The above equipment (model: 0P4E230) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Sep. 05, 2013 Ivonne Wu / Senior Specialist APPROVED BY : , DATE: Sep. 05, 2013 Sam Chen / Assistant Manager Report No.: RF130722C16-3 5 of 30 Report Format Version 5.0.0

2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: STANDARD TEST TYPE RESULT REMARK SECTION 2.1046 Equivalent isotropically radiated power PASS Meet the requirement of limit. 27.50(d)(4) 2.1055 Frequency Stability PASS Meet the requirement of limit. 27.54 2.1049 Occupied Bandwidth PASS Meet the requirement of limit. 27.53(h) 27.50(d)(5) Peak to average ratio PASS Meet the requirement of limit. 27.53(h) Band Edge Measurements PASS Meet the requirement of limit. 2.1051 Conducted Spurious Emissions PASS Meet the requirement of limit. 27.53(h) Meet the requirement of limit. 2.1053 Radiated Spurious Emissions PASS Minimum passing margin is 27.53(h) -25.43dB at 40.26MHz. 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: MEASUREMENT FREQUENCY UNCERTAINTY Conducted emissions 150kHz~30MHz 2.44 dB 30MHz ~ 200MHz 2.93 dB 200MHz ~1000MHz 2.95 dB Radiated emissions 1GHz ~ 18GHz 2.26 dB 18GHz ~ 40GHz 1.94 dB This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Report No.: RF130722C16-3 6 of 30 Report Format Version 5.0.0

2.2 TEST SITE AND INSTRUMENTS DESCRIPTION & DATE OF DUE DATE OF MODEL NO. SERIAL NO. MANUFACTURER CALIBRATION CALIBRATION Test Receiver ESCI 100744 Apr. 15, 2013 Apr. 14, 2014 ROHDE & SCHWARZ Spectrum Analyzer FSU43 101261 Dec. 17, 2012 Dec. 16, 2013 ROHDE & SCHWARZ BILOG Antenna VULB9168 9168-472 Mar. 25, 2013 Mar. 24, 2014 SCHWARZBECK HORN Antenna BBHA 9120 D 9120D-969 Jan. 07, 2013 Jan. 06, 2014 SCHWARZBECK HORN Antenna BBHA 9170 9170-480 Dec. 25, 2012 Dec. 24, 2013 SCHWARZBECK Loop Antenna HFH2-Z2 100070 Jan. 31, 2012 Jan. 30, 2014 Preamplifier EMC 012645 980115 Dec. 28, 2012 Dec. 27, 2013 EMCI Preamplifier EMC 184045 980116 Dec. 28, 2012 Dec. 27, 2013 EMCI Preamplifier EMC 330H 980112 Dec. 28, 2012 Dec. 27, 2013 EMCI RF signal cable SUCOFLEX 104 309219/4 Oct. 19, 2012 Oct. 18, 2013 HUBER+SUHNNER RF signal cable SUCOFLEX 104 250130/4 Oct. 19, 2012 Oct. 18, 2013 HUBER+SUHNNER RF signal cable RG-213 NA Dec. 29, 2012 Dec. 28, 2013 Worken Software E3 NA NA NA BV ADT 6.120103 Antenna Tower MFA-440H NA NA NA MF Turn Table MFT-201SS NA NA NA MF Antenna Tower &Turn Table Controller MF-7802 NA NA NA MF Mini-Circuits Power Splitter ZN2PD-9G NA Jul. 18, 2013 Jul. 17, 2014 JFW 20dB attenuation 50HF-020-SMA NA NA NA Communications E5515C MY52102544 Sep. 05, 2012 Sep. 04, 2013 Tester-Wireless Radio Communication MT8820C 6201300640 Aug. 01, 2013 Jul. 31, 2014 Analyzer NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 10. 3. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Site Registration No. is 690701. 5. The IC Site Registration No. is IC 7450F-10. Report No.: RF130722C16-3 7 of 30 Report Format Version 5.0.0

3 GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT PRODUCT Smartphone MODEL NO. 0P4E230 5Vdc (adapter or host equipment) POWER SUPPLY 3.8Vdc (battery) MODULATION WCDMA Band 4 QPSK, BPSK TECHNOLOGY FREQUENCY RANGE WCDMA Band 4 1712.4MHz ~1752.6MHz EMISSION DESIGNATOR WCDMA Band 4 4M18F9W MAX. EIRP POWER WCDMA Band 4 143.52mW ANTENNA TYPE Fixed Internal Antenna DATA CABLE Refer to Note as below I/O PORTS Refer to users’ manual ACCESSORY DEVICES Refer to Note as below NOTE: 1. The EUT’s accessories list refers to Ext. Pho. 2. The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF130722C16-3 8 of 30 Report Format Version 5.0.0

3.2 CONFIGURATION OF SYSTEM UNDER TEST FOR RADIATION EMISSION TEST EUT (Powered from adapter) Earphone zzg Test table $ Universal Radio Communication Tester Kept in a remote area FOR E.R.P. / E.1.R.P. TEST EUT (Powered from battery) Py Test table $s Universal Radio Communication Tester *Kept in a remote area 3.3 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. Report No.: RF130722C16—3 9 of 30 Report Format Version 5.0.0

3.4 DESCRIPTION OF TEST MODES Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates, XYZ axis and antenna ports The worst case was found when positioned on Y-plane for ERP and Z-axis for radiated emission. Following channel(s) was (were) selected for the final test as listed below: WCDMA TEST ITEM AVAILABLE CHANNEL TESTED CHANNEL MODE EIRP 1312 to 1513 1312, 1413, 1513 WCDMA FREQUENCY STABILITY 1312 to 1513 1413 WCDMA OCCUPIED BANDWIDTH 1312 to 1513 1312, 1413, 1513 WCDMA BAND EDGE 1312 to 1513 1312, 1513 WCDMA CONDCUDETED EMISSION 1312 to 1513 1413 WCDMA RADIATED EMISSION 1312 to 1513 1413 WCDMA TEST CONDITION: TEST ITEM ENVIRONMENTAL CONDITIONS INPUT POWER TESTED BY ERP/EIRP 26deg. C, 58%RH 3.8Vdc Howard Kao FREQUENCY STABILITY 26deg. C, 58%RH 3.8Vdc Howard Kao OCCUPIED BANDWIDTH 26deg. C, 58%RH 3.8Vdc Howard Kao BAND EDGE 26deg. C, 58%RH 3.8Vdc Howard Kao CONDCUDETED EMISSION 26deg. C, 58%RH 3.8Vdc Howard Kao RADIATED EMISSION 25deg. C, 65%RH 120Vac, 60Hz Johnson Liao Report No.: RF130722C16-3 10 of 30 Report Format Version 5.0.0

3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC 47 CFR Part 2 FCC 47 CFR Part 27 ANSI C63.4-2003 ANSI/TIA/EIA-603-C 2004 NOTE: All test items have been performed and recorded as per the above standards. Report No.: RF130722C16-3 11 of 30 Report Format Version 5.0.0

4 TEST TYPES AND RESULTS 4.1 OUTPUT POWER MEASUREMENT 4.1.1 LIMITS OF QOUTPUT POWER MEASUREMENT Fixed, mobile, and portable (hand—held) stations operating in the 1710—1755 MHz band are limited to 1 watt EIRP. 4.1.2 TEST PROCEDURES EIRP MEASUREMENT: a. All measurements were done at low, middle and high operational frequency range. RBW and VBW is S5MHz for WCDMA mode. b. Substitution method is used for E.1.R.P measurement. In the semi—anechoic chamber, EUT placed on the 0.8m height of Turn Table, rotated the table around 360 degrees to search the maximum radiation power and receiver antenna shall be rotated vertical and horizontal polarization and moved height from 1m to 4m to find the maximum polar radiated power. The "Read Value" is the spectrum reading the maximum power value. c. The substitution horn antenna is substituted for EUT at the same position and signals generator export the CW signal to the substitution antenna via a tx cable. Rotated the Turn Table and moved receiving antenna to find the maximum radiation power. Adjust output power level of S.G to get a Value of spectrum reading equal to "Read Value" of step b. Record the power level of S.G d. EIRP = Output power level of S.G — TX cable loss + Antenna gain of substitution horn. CONDUCTED POWER MEASUREMENT: a. The EUT was set up for the maximum power with WCDMA link data modulation and link up with simulator. b. Set the EUT to transmit under low, middle and high channel and record the power level shown on simulator. Report No.: RF130722C16—3 12 of 30 Report Format Version 5.0.0

4.1.3 TEST SETUP EIRP / ERP MEASUREMENT: 1~4m 3m CONDUCTED POWER MEASUREMENT: COMMUNICATION EUT SIMULATOR Report No.: RF130722C16-3 13 of 30 Report Format Version 5.0.0

4.1.4 TEST RESULTS AVERAGE CONDUCTED QUTPUT POWER (dBm) Band WCDMA IV Channel 1312 1413 1513 Frequency (MHz) 17124 1732.6 1752.6 RMC 12.2K 24.12 23.84 23.87 HSDPA Subtest—1 23.11 22.83 22.86 HSDPA Subtest—2 21.47 21.19 21.22 HSDPA Subtest—3 20.15 19.87 19.90 HSDPA Subtest—4 19.99 19.71 19.74 HSUPA Subtest—1 22.66 22.38 22.41 HSUPA Subtest—2 20.86 20.58 20.61 HSUPA Subtest—3 21.82 21.54 21.57 HSUPA Subtest—4 20.69 20.41 20.44 HSUPA Subtest—5 23.04 22.66 22.69 AVERAGE EIRP (dBm) WCDMA Frequency LVL Correction Polarization Plane Channel (MHz) (dBm) Factor(dB) EIRP(dBm) EIRP(mW) (wv) 1312 1712.4 —20.73 36.29 15.56 35.97 1413 1732.6 —21.40 36.69 15.29 33.80 H v 1513 1752.6 —21.17 36.98 15.81 38.10 1312 1712.4 —16.08 37.11 21.03 126.71 1413 1732.6 —16.44 37.60 21.16 130.62 V 1513 1752.6 —16.08 37.65 21.57 143.52 Report No.: RF130722C16—3 14 of 30 Report Format Version 5.0.0

4.2 FREQUENCY STABILITY MEASUREMENT 4.2.1 LIMITS OF FREQUENCY STABILIITY MEASUREMENT The frequency stability shall be sufficient to ensure that the fundamental emissions stay within the authorized bands of operation. 4.2.2 TEST PROCEDURE a. Device is placed at the oven room. The oven room could control the temperatures and humidity. Power warm up is at least 15 min and power applied should perform before recording frequency error. b. EUT is connected the external power supply to control the DC input power. The test voltage range is from minimum to maximum working voltage. Each step shall be record the frequency error rate. c. The temperature range step is 10 degrees in this test items. All temperature levels shall be hold the £0.5°C during the measurement testing. The each temperature step shall be at least 0.5 hours, consider the EUT could be test under the stability condition. NOTE: The frequency error was recorded frequency error from the communication simulator. 4.2.3 TEST SETUP OVEN ROOM COMMUNICATION SIMULATOR ANTENNA EXTERNAL POWER SOURCE EUT DC POWER SUPPLY Report No.: RF130722C16—3 15 of 30 Report Format Version 5.0.0

4.2.4 TEST RESULTS voLTacE FREQUENCY ERROR (ppm) man (Volts) WCDMA 3.8 0.004 2.5 3.6 0.004 2.5 4.34 0.004 2.5 NOTE: The applicant defined the normal working voltage of the battery is from 3.6Vdc to 4.34Vdc. iuko FREQUENCY ERROR (ppm) man WCDMA —30 0.004 2.5 20 0.004 2.5 10 0.005 2.5 0 0.004 2.5 10 0.004 2.5 20 0.004 2.5 30 0.004 2.5 40 0.005 2.5 50 0.004 2.5 60 0.004 2.5 Report No.: RF130722C16—3 16 of 30 Report Format Version 5.0.0

4.3 OCCUPIED BANDWIDTH MEASUREMENT 4.3.1 LIMITS OF OCCUPIED BANDWIDTH MEASUREMENT The width of a frequency band such that, below the lower and above the upper frequency limits, the mean powers emitted are each equal to a specified percentage 0.5 %of the total mean power of a given emission. 4.3.2 TEST SETUP COMMUNICATION SIMULATOR POWER SPLITTER _ SPECTRUM ANALYZER 300B ATTENUATION PAD EUT 4.3.3 TEST PROCEDURES a. The conducted occupied bandwidth used the power splitter via EUT RF power connector between simulation base station and spectrum analyzer. b. Use OBW measurement function of Spectrum analyzer to measure 99 % occupied bandwidth. Report No.: RF130722C16—3 17 of 30 Report Format Version 5.0.0

4.3.4 TEST RESULTS WCDMA FREQUENCY 99% OCCUPIED CHANNEL (MHz) BANDWIDTH (MHz) 1312 1712.4 4.1706 1413 1732.6 4.1747 1513 1752.6 4.1782 SPECTRUM PLOT OF WORST VALUE Report No.: RF130722C16-3 18 of 30 Report Format Version 5.0.0

4.4 PEAK TO AVERAGE RATIO 4.4.1 LIMITS OF PEAK TO AVERAGE RATIO MEASUREMENT In measuring transmissions in this band using an average power technique, the peak to-average ratio (PAR) of the transmission may not exceed 13 dB 4.4.2 TEST SETUP COMMUNICATION SIMULATOR POWER SPLITTER SPECTRUM ANALYZER 30dB ATTENUATION PAD EUT 4.4.3 TEST PROCEDURES 1. Set resolution/measurement bandwidth ≥ signal’s occupied bandwidth; 2. Set the number of counts to a value that stabilizes the measured CCDF curve; 3. Record the maximum PAPR level associated with a probability of 0.1%. Report No.: RF130722C16-3 19 of 30 Report Format Version 5.0.0

4.4.4 TEST RESULTS WCDMA FREQUENCY PEAK TO AVERAGE CHANNEL (MHz) RATIO (dB) 1312 1712.4 2.93 1413 1732.6 3.11 1513 1752.6 2.79 SPECTRUM PLOT OF WORST VALUE Report No.: RF130722C16-3 20 of 30 Report Format Version 5.0.0

4.5 BAND EDGE MEASUREMENT 4.5.1 LIMITS OF BAND EDGE MEASUREMENT For operations in the 1710 — 1755 MHz MHz bands, the power of any emission outside a licensee‘s frequency block shall be attenuated below the transmitter power (P) by at least 43 + 10 log10(P) dB. 4.5.2 TEST SETUP COMMUNICATION SIMULATOR POWER SPLITTER _ SPECTRUM ANALYZER 300B ATTENUATION PAD EUT 4.5.3 TEST PROCEDURES a. The EUT was set up for the maximum peak power with LTE link data modulation. The power was measured with R&S Spectrum Analyzer. All measurements were done at 2 channels (low and high operational frequency range.). b. The band edge measurement used the power splitter via EUT RF power connector between simulation base station and spectrum analyzer. c. The center frequency of spectrum is the band edge frequency and span is 5 MHz. RB of the spectrum is 100kHz and VB of the spectrum is 300kHz. d. Record the max trace plot into the test report. Report No.: RF130722C16—3 21 of 30 Report Format Version 5.0.0

4.5.4 TEST RESULTS WCDMA CHANNEL 1312 CHANNEL 1513 Report No.: RF130722C16-3 22 of 30 Report Format Version 5.0.0

4.6 CONDUCTED SPURIOUS EMISSIONS 4.6.1 LIMITS OF CONDUCTED SPURIOUS EMISSIONS MEASUREMENT The power of any emission outside a licensee's frequency block shall be attenuated below the transmitter power (P) by at least 43 +10 log10(P) dB. The limit of emission equal to –13dBm 4.6.2 TEST PROCEDURE a. The EUT makes a phone call to the communication simulator. All measurements were done at low, middle and high operational frequency range. b. Measuring frequency range is from 30 MHz to 8GHz for LTE Band 17 and from 30MHz to 18GHz for LTE Band 4. 10dB attenuation pad is connected with spectrum. RBW=1MHz and VBW=3MHz are used for conducted emission measurement. 4.6.3 TEST SETUP COMMUNICATION SIMULATOR POWER SPLITTER SPECTRUM ANALYZER 10dB ATTENUATION PAD EUT Report No.: RF130722C16-3 23 of 30 Report Format Version 5.0.0

4.6.4 TEST RESULTS CHANNEL 1413 FREQUENCY RANGE : 30MHz~18GHz Report No.: RF130722C16-3 24 of 30 Report Format Version 5.0.0

4.7 RADIATED EMISSION MEASUREMENT 4.7.1 LIMITS OF RADIATED EMISSION MEASUREMENT The power of any emission outside a licensee‘s frequency block shall be attenuated below the transmitter power (P) by at least 43 +10 log10(P) dB. The limit of emission equal to —13dBm 4.7.2 TEST PROCEDURES a. Substitution method is used for E.L.R.P measurement. In the semi—anechoic chamber, EUT placed on the 0.8m height of Turn Table, rotated the table around 360 degrees to search the maximum radiation power and receiver antenna shall be rotated vertical and horizontal polarization and moved height from 1m to 4m to find the maximum polar radiated power. The "Read Value" is the spectrum reading the maximum power value. . The substitution horn antenna is substituted for EUT at the same position and signals generator export the CW signal to the substitution antenna via a TX cable. Rotated the Turn Table and moved receiving antenna to find the maximum radiation power. Adjust output power level of S.G to get a Value of spectrum reading equal to "Read Value " of step a. Record the power level of S.G . EIRP = Output power level of S.G — TX cable loss + Antenna gain of substitution horn. . E.R.P power can be calculated form E.1.R.P power by subtracting the gain of dipole, E.R.P power = E.1.P.R power — 2.150Bi. NOTE: The resolution bandwidth of spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz. 4.7.3 DEVIATION FROM TEST STANDARD No deviation Report No.: RF130722C16—3 25 of 30 Report Format Version 5.0.0

4.7.4 TEST SETUP For the actual test configuration, please refer to the attached file (Test Setup Photo). Report No.: RF130722C16-3 26 of 30 Report Format Version 5.0.0

4.7.5 TEST RESULTS WCDMA PART 27 3m HORIZONTAL Report No.: RF130722C16-3 27 of 30 Report Format Version 5.0.0

PART 27 3m VERTICAL Report No.: RF130722C16-3 28 of 30 Report Format Version 5.0.0

5 INFORMATION ON THE TESTING LABORATORIES We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Hsin Chu EMC/RF Lab: Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety/Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.adt.com.tw The address and road map of all our labs can be found in our web site also. Report No.: RF130722C16-3 29 of 30 Report Format Version 5.0.0

6 APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB No modifications were made to the EUT by the lab during the test. ---END--- Report No.: RF130722C16-3 30 of 30 Report Format Version 5.0.0


Document Created: 2013-09-13 18:08:27
Document Modified: 2013-09-13 18:08:27
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC