Modular Approval Request Letter

FCC ID: NKRIMA2A

Cover Letter(s)

Download: PDF
FCCID_4016734

Applicant/Grantee Wistron NeWeb Corporation/ NKR FCC ID NKRIMA2ZA _Section 15.212 ModularTransmitters _ Request for ModularAppm\}él [ [ | Request for Limited Modular Approval | Requ1rements EUT Condmons Comply (Y/N) _ _ — SingleModularApproval Requirements_ 200000 . The radlo elements ofthe modular The radio portion of this module has Y transmitter must have their own been shielded, please see exhibition shielding. The physical erystal and external photos. tuning capacitors may be located external to the shielded radio elements. The modular transmitter must have Buffered data inputs stage has been Y buffered modulation/data inputs (if such integrated in chip ALT1250TG. inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over—modulation. The modular transmitter must have its The part number of the power regulator Y own power supply regulation. is SKY68020—11. Please see the schem.pdf The modular transmitter must comply The requirements of antenna connector Y with the antenna and transmission and spurious emission have been system requirements of Sections 15.203, fulfilled. Please refer to the Test Report 15.204(b) and 15.204(c). The antenna exhibition. must either be permanently attached or employ a "unique" antenna coupler (at all connections between the module and the antenna, including the cable). The "professional installation" provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The modular transmitter must be tested Please refer to the Setup Photo Y in a stand—alone configuration, 7.e., the exhibition for the stand—alone test module must not be inside another configuration. device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between

the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(1)). The modular transmitter must be The LTE Module will be labeled with its equipped with either a permanently own FCC ID, and the instruction on the affixed label or must be capable of labeling rule of the end product has been electronically displaying its FCC stated in the User Manual of this identification number. module. Please refer to the Label and (4) If using a permanently affixed label, the User Manual exhibition. modulartransmitter must be labeled with its own FCC identification number, and, ifthe FCC identification number is not visible when the module is installed inside another device, then the outside ofthe device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as thefollowing: "Contains Transmitter Module FCC ID: XYZMODEL1" or "Contains FCC ID: XYZMODEL1." Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example ofwhich must be included in the applicationfor equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the applicationfor equipment authorization. (B) Ifthe modular transmitter uses an electronic display ofthe FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. Ifthe module is installed inside another device, then the outside ofthe device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as thefollowing: "Contains FCC certified transmitter module(s)." Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy ofthese instructions must be included in the application for equipment authorization. The modular transmitter must comply The required FCC rule has been fulfilled with any specific rules or operating and all the instructions for maintaining requirements that compliance have been clearly stated in ordinarily apply to a complete the User Manual. transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the

application for equipment authorizstion. | 8 The modular transmitter must comply Please refer exhibition RF Exposure for with any applicable RF exposure the compliance of MPE RF exposure requirements in its final configuration. rule. PnNXA We Brian Lin Brian.Lin@wne.com.tw


Document Created: 2019-03-28 08:17:43
Document Modified: 2019-03-28 08:17:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC