Users Manual

FCC ID: NKR-XRAV1

Users Manual

Download: PDF
FCCID_3150120

XRAV-1 USER MANUAL (V0.9) Model Name: XRAV-1 NFC MODULE Description: NFC reader/writter module compatible Version : V 0.9 This document contains proprietary information which is the property of Wistron NeWeb Corporation and is strictly confidential and shall not be disclosed to others in whole or in part, reproduced, copied, or used as basic for design, manufacturing or sale of apparatus without the written permission of Wistron NeWeb Corporation. NFC module Delivery Specification V0.9

1. Introduction XRAV-1 is a kind of NFC (Near Field Communication) module that could be embedded in one IT system by simply connecting the module through I2C interface and start developing his application software. 2. Hardware Block Diagram XRAV-1 is a full feature NFC module and compliant with NFC standards (NFC Forum, EMVCo, ETSI/SCP). XRAV-1 has an optimized architecture for low-power consumption in different operation modes. The RF contactless front-end is supporting various transmission modes according to NFCIP-1, NFCIP-2, ISO/IEC14443, ISO/IEC 15693, ISO-14443, MIFARE, and FeliCa specifications. The major internal components are illustrated in Figure 1-1. Host FPC/FFC Connector Antenna Connector FPC/FFC CABLE Insert into Connector Figure 1-1 NFC module Major Component and System Interface (Assembly Guide) Note: • Host FPC/FFC Connector: Allow user to connect the XRAV-1 module to the host board via FPC/FFC connector. • Antenna Connector: Connected to FPC antenna, please note that matching circuitry should be design on antenna. NFC module Delivery Specification 1 V0.9

3. Pin Definition 3.1 FPC/FFC connector type Host connector Pin number Name Configuration Description 1 MOD_VDD Power Supply Input Module power supply 2 MOD_GND Power Supply Ground Module ground 3 SWP Input/ Output Single Wire Protocol line to UICC/ SIM 4 MOD_VUP Power Supply Input Power supply for RF Front-end Interrupt request from module to 5 IRQ Output platform The power rail used to power UICC/ VDD_SIM SIM. Applicable in a system where NFC 6 Power supply input (PMUVCC) module used SWP to communicate with an UICC/SIM in the platform 7 I2C_SDA Input/ Output I2C data 8 I2C_SCL Input I2C clock 9 MOD_GND Input Used for extra GND for signal integrity Reset pin input from the host to wake up 10 Reset/ WakeUp Input the device from standby and also to reset the device Control pin to set the NPC300 in 11 DWL_REQ Input firmware download mode Power supply to UICC/ SIM or power supply ‘request’ to PMIC. Applicable in 12 SWP_PWR Power Supply Output a system where NFC module uses SWP (SIM_VCC) to communicate with an UICC/ SIM in the platform. Additional pin for module power supply 13 MOD_VDD Power supply input to support higher current capacity 14 VDD_IO Power supply input Host IO reference voltage 15 MOD_GND Power Supply Ground Module ground Antenna connector Pin number Name Configuration Description 1 ANT1 Output Connection for antenna load modulation #1 2 RXP Input Antenna reception path #1 3 TX1 Output Antenna transmission line #1 4 GND Ground Antenna ground 5 TX2 Output Antenna transmission line #2 6 RXN Input Antenna reception path #2 7 ANT2 Output Connection for antenna load modulation #2 NFC module Delivery Specification 2 V0.9

3.2 SMT type Pin number Name Configuration Description 1 MOD_VUP Power Supply Input Power supply for RF Front-end Interrupt request from module to 2 IRQ Output platform The power rail used to power UICC/ VDD_SIM SIM. Applicable in a system where NFC 3 Power supply input (PMUVCC) module used SWP to communicate with an UICC/SIM in the platform 4 I2C_SDA Input/ Output I2C data 5 I2C_SCL Input I2C clock Reset pin input from the host to wake up 6 Reset/ WakeUp Input the device from standby and also to reset the device Control pin to set the NPC300 in 7 DWL_REQ Input firmware download mode 8 VDD_IO Power supply input Host IO reference voltage 9 MOD_GND Power Supply Ground Module ground 10 MOD_GND Power Supply Ground Module ground Connection for antenna load modulation 11 ANT1 Output #1 12 RXP Input Antenna reception path #1 13 TX1 Output Antenna transmission line #1 14 GND Ground Antenna ground 15 TX2 Output Antenna transmission line #2 16 RXN Input Antenna reception path #2 Connection for antenna load modulation 17 ANT2 Output #2 18 MOD_VDD Power Supply Input Module power supply 19 SWP Input/ Output Single Wire Protocol line to UICC/ SIM NFC module Delivery Specification 3 V0.9

4. Specification Item Standard specifications Main chipset  NXP NPC300 Frequency  13.56MHz  ISO/IEC 14443A, ISO/IEC 14443B PCD  FeliCa PCD mode  Mifare PCD encryption mechanism  ISO/IEC 15693/ICODE VCD mode NFC  NFC Forum tags Standards  NFCIP-1/NFCIP-2 protocol  EMVCo 2.0.1 for PICC and PCD mode  NFC Forum Wave 1 and Wave 2  ETSI/SCP 102 613 and 102 622 for SWP/HCI  NCI protocol interface according to NFC Forum NCI 1.0 standardization Host interface  I2C High-speed mode supported I2C Address  0x29 Host  15 pin FPC/FFC connector Antenna  7 pin FPC/FFC connector Operation  -25 ~ 80o C temperature Storage  -25o ~ 125o C temperature 5. Electrical Characteristics Recommended Operating conditions Symbol Parameter Min Typical Maximum Unit MOD_VDD Power supply input 2.7 3.3 5.5 MOD_VUP Power supply input 2.7 3.3 5.5 1.62 1.8 1.98 VDD_IO IO power supply 3.0 3.3 3.6 V 1.62 1.8 1.98 VDD_SIM Power supply input 3.0 3.3 3.6 Power supply for SWP SWP_PWR[1] 1.62 1.8 1.98 interface [1] No VDD_SIM power supply input. Current consumption characteristics Symbol Min Typical Maximum Unit IMOD_VDD -- -- 190[1] mA IVDD_IO -- -- 15 [1] MOD_VDD=3.3V NFC module Delivery Specification 4 V0.9

6. Recommended Operation Temperature Supply voltage  AC mains DC Type of DC Source  Internal DC supply  External DC adapter  Battery Operational Climatic  Tnom (20°C)  Tmax (80°C)  Tmin (-25°C) NFC module Delivery Specification 5 V0.9

7. Host Reference Circuit 7.1 No SIM Card used 7.2 SIM Card used on mother board NFC module Delivery Specification 6 V0.9

8. Certifications and Regulatory Item Feature Description RF: FCC part 15C 14.1 FCC EMI: FCC part 15B RSS-210 ISSUE 8 14.2 IC RSS-GEN ISSUE 4 RF: EN 302 291-1 V1.1.1, EN 302 291-2 V1.1.1 EN 300 330-1 V1.8.1, EN 300 330-2 V1.6.1 14.3 CE EMC: EN 301 489-1 V1.9.2, EN 301 489-3 V1.6.1 Safety: EN 60950-1:2006/A11:2009+A1:2010+A12:2011+A2:2013 RF: LP0002 14.4 NCC EMI: CNS 13438 14.5 SAR EN62311 General: This modular approval is limited to OEM/Integrators installation only. OEM integrators are responsible for ensuring that the end-user has no manual instructions to remove or install module. The end user manual shall include all required regulatory information/warning as show in this manual. End Product Labeling (FCC) When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text: “Contains FCC ID: _NKR-XRAV1_________ The grantee's FCC ID can be used only when all FCC compliance requirements are met. Required FCC Compliance Statement for Host Integration To integrate this module into the host, the host manufacturer is responsible for the applicable FCC rules, including the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. In the user manual of the host device, the following statements are required to be included.  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NFC module Delivery Specification 7 V0.9

 This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.  Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Module Integration Restriction: This device is intended only for OEM integrators under the following conditions: (1) The antenna must be installed such that 20 cm is maintained between the antenna and users, (2) The transmitter module may not be co-located with any other transmitter or antenna. (3) The Loop antenna was verified in the conformity testing. Radiated transmit power must be equal to or lower than that specified in the FCC/IC Grant of Equipment Authorization for FCC ID: NKR-XRAV1 and IC: 4441A-XRAV1. A separate approval is required for all other antenna type, or higher gain antenna. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/IC authorization is no longer considered valid and the FCC ID/IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/IC authorization. NFC module Delivery Specification 8 V0.9

Radiation Exposure Statement This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. R&TTE Regulation: In all cases assessment of the final product must be met against the Essential requirements of the R&TTE Directive Articles 3.1(a) and (b), safety and EMC respectively, as well as any relevant Article 3.3 requirements. 1. The Loop antenna (gain: N/A dBi) was verified in the conformity testing, and for compliance the antenna shall not be modified. A separate approval is required for all other operating configurations, including different antenna configurations. 2. If any other simultaneous transmission radio is installed in the host platform together with this module, or above restrictions cannot be kept, a separate RF exposure assessment and CE equipment certification is required. CE RF Exposure Compliance This device meets the EU requirements and the International Commission on Non-Ionizing Radiation Protection (ICNIRP) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. To comply with the RF exposure requirements, this equipment must be operated in a minimum of 20 cm separation distance to the user. 1177 NFC module Delivery Specification 9 V0.9

End Product Labeling (IC) Labeling Requirements for the Host Device (Section 3.2, RSP-100, Issue 11, January 2016): The host device shall be properly labeled to identify the module within the host device. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the Industry Canada certification number of the module, preceded by the words ―Contains transmitter module, or the word ―Contains, or similar wording expressing the same meaning, as follows: "Contains transmitter module IC:_4441A-XRAV1___. Required IC Compliance Statement for Host Integration To integrate this module into the host, the host manufacturer is responsible for the applicable Industry Canada rules, including the limits for a Class B digital device, pursuant to ICES-003 of the Industry Canada Rules CAN ICES-3(B)/ NMB-3(B) In the user manual of the host device, the following statements are required to be included.  This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.  Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement." IC Module Integration Restriction: This module has been certified by Industry Canada as modular approval with the following restrictions: 1. The Loop antenna was verified in the conformity testing, and for compliance the antenna shall not be modified. A separate approval is required for all other operating configurations, including different antenna configurations. 2. If any other simultaneous transmission radio is installed in the host platform together with this module, or above restrictions cannot be kept, a separate RF exposure assessment and IC equipment certification is required. NFC module Delivery Specification 10 V0.9

NCC remind 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司 商號或使用者均 不得擅自變更頻率 加大功率或變更原設計之特性及功能 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干 擾現象時，應立即停用，並改善至無干擾時方得繼續使用 前項合法通信，指依電信法規定作業之無線電通信 低功率射頻電機須忍受合法通信或工業 科學及醫療用電波輻射性電機 設備之干擾 NFC module Delivery Specification 11 V0.9

NCC logo location NFC module Delivery Specification 12 V0.9


Document Created: 2017-12-15 10:39:46
Document Modified: 2017-12-15 10:39:46
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC