RF Test Report-8

FCC ID: NKR-LVSK-ODU

Test Report

Download: PDF
FCCID_4317864

Band n261 Beam ID 47+176 Frequency Range 75GHz-110GHz Channel High Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 47+176 Frequency Range 75GHz-110GHz Channel High Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 356 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56 Frequency Range 50GHz-75GHz Channel Low Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56 Frequency Range 50GHz-75GHz Channel Low Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 357 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56 Frequency Range 50GHz-75GHz Channel Mid Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56 Frequency Range 50GHz-75GHz Channel Mid Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 358 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56 Frequency Range 50GHz-75GHz Channel High Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56 Frequency Range 50GHz-75GHz Channel High Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 359 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56+184 Frequency Range 50GHz-75GHz Channel Low Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56+184 Frequency Range 50GHz-75GHz Channel Low Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 360 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56+184 Frequency Range 50GHz-75GHz Channel Mid Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56+184 Frequency Range 50GHz-75GHz Channel Mid Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 361 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56+184 Frequency Range 50GHz-75GHz Channel High Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56+184 Frequency Range 50GHz-75GHz Channel High Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 362 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56 Frequency Range 75GHz-110GHz Channel Low Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56 Frequency Range 75GHz-110GHz Channel Low Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 363 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56 Frequency Range 75GHz-110GHz Channel Mid Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56 Frequency Range 75GHz-110GHz Channel Mid Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 364 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56 Frequency Range 75GHz-110GHz Channel High Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56 Frequency Range 75GHz-110GHz Channel High Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 365 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56+184 Frequency Range 75GHz-110GHz Channel Low Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56+184 Frequency Range 75GHz-110GHz Channel Low Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 366 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56+184 Frequency Range 75GHz-110GHz Channel Mid Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56+184 Frequency Range 75GHz-110GHz Channel Mid Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 367 / 415 Report Format Version: 6.1.1

Band n261 Beam ID 56+184 Frequency Range 75GHz-110GHz Channel High Antenna polarity Horizontal Test distance 1m Note: The test results already include the correction factor (corrections: On). Band n261 Beam ID 56+184 Frequency Range 75GHz-110GHz Channel High Antenna polarity Vertical Test distance 1m Note: The test results already include the correction factor (corrections: On). Report No.: RF190401E07-6 Page No. 368 / 415 Report Format Version: 6.1.1

4.5 Out-of-Band Emission at the Band Edge Measurement 4.5.1 Limits of Out-of Band Emission at the Band Edge Measurement The conductive power or the total radiated power of any emission outside a licensee's frequency block shall be −13 dBm/MHz or lower. However, in the bands immediately outside and adjacent to the licensee's frequency block, having a bandwidth equal to 10 percent of the channel bandwidth, the conductive power or the total radiated power of any emission shall be −5 dBm/MHz or lower. 4.5.2 Test Instruments Refer to section 4.5.2. 4.5.3 Test Procedures a. Substitution method is used for E.I.R.P measurement. In the semi-anechoic chamber, EUT placed on the 0.8m(below or equal 1GHz) and/or 1.5m(above 1GHz) height of Turn Table, rotated the table around 360 degrees to search the maximum radiation power and receiver antenna shall be rotated vertical and horizontal polarization and moved height from 1m to 4m to find the maximum polar radiated power. The “Read Value” is the spectrum reading the maximum power value. b. The substitution antenna is substituted for EUT at the same position and signals generator export the CW signal to the substitution antenna via a TX cable. Rotated the Turn Table and moved receiving antenna to find the maximum radiation power. Adjust output power level of S.G to get a Value of spectrum reading equal to “Read Value“ of step a. Record the power level of S.G. c. EIRP = Output power level of S.G – TX cable loss + Antenna gain of substitution horn. d. E.R.P power can be calculated form E.I.R.P power by subtracting the gain of dipole, E.R.P power = E.I.R.P power - 2.15dBi. e. The requirements in 30.203 are expressed in terms of conductive power, and then conducted power will be calculated by EIRP-Array Gain. f. Antenna Gain Information at the Band Edge : The following antenna gain information is provided to demonstrate the antenna performance of the 37~40 GHz band. These antenna gains were subtracted from the measured E.I.R.P levels at lower and upper band edge frequencies to determine an equivalent conductive power that was compared directly with the part 30.203 limits. Band 260 Frequency (GHz) Gain (dBi) 37.6 8.07 40 8.88 Band 261 Frequency (GHz) Gain ( dBi) 27.5 10.33 28.35 9.84 Note: The resolution bandwidth of spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz. Report No.: RF190401E07-6 Page No. 369 / 415 Report Format Version: 6.1.1

4.5.4 Deviation from Test Standard No deviation. 4.5.5 Test Set Up Ant. Tower 1-4m Variable EUT& 1m Support Units Turn Table Absorber 150cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.5.6 EUT Operating Conditions a. Connected the Adapter to EUT. b. Prepared notebook to act as communication partner and placed it outside of testing area. c. The communication partner connected with EUT via a RJ45 cable and ran a test program (provided by manufacturer) to enable EUT under transmission condition continuously at specific channel frequency. d. The communication partner sent data to EUT by command "PING". Report No.: RF190401E07-6 Page No. 370 / 415 Report Format Version: 6.1.1

4.5.7 Test Results Lowest-edge Band n260 Component Carriers 1CC Modulation QPSK RB 1RB0 Conducted Frequency EIRP Value Array Gain Limit Margin Beam ID Power Result (GHz) (dBm) (dBi) (dBm) (dB) (dBm) 37.59960 0.706 8.07 -7.364 -5 -2.364 Pass 164 37.59475 -9.863 8.07 -17.933 -13 -4.933 Pass 37.59965 2.018 8.07 -6.052 -5 -1.052 Pass 184 37.58720 -12.689 8.07 -20.759 -13 -7.759 Pass 37.59925 -0.349 8.07 -8.419 -5 -3.419 Pass 189 37.59465 -8.305 8.07 -16.375 -13 -3.375 Pass 37.59940 0.182 8.07 -7.888 -5 -2.888 Pass 40+164 37.59390 -11.633 8.07 -19.703 -13 -6.703 Pass 37.59950 1.743 8.07 -6.327 -5 -1.327 Pass 58+184 37.59360 -13.647 8.07 -21.717 -13 -8.717 Pass 37.59900 0.800 8.07 -7.270 -5 -2.270 Pass 61+189 37.59425 -11.182 8.07 -19.252 -13 -6.252 Pass Note: The Conducted Power = EIRP-Array Gain Report No.: RF190401E07-6 Page No. 371 / 415 Report Format Version: 6.1.1

Beam 164 Beam 184 Beam 189 Beam 40+164 Beam 58+184 Beam 61+189 Report No.: RF190401E07-6 Page No. 372 / 415 Report Format Version: 6.1.1

Lowest-edge Band n260 Component Carriers 2CC Modulation QPSK RB 1RB0 Conducted Frequency EIRP Value Array Gain Limit Margin Beam ID Power Result (GHz) (dBm) (dBi) (dBm) (dB) (dBm) 37.59990 -7.492 8.07 -15.562 -5 -10.562 Pass 164 37.59280 -12.758 8.07 -20.828 -13 -7.828 Pass 37.59990 -5.610 8.07 -13.680 -5 -8.680 Pass 184 37.58110 -13.307 8.07 -21.377 -13 -8.377 Pass 37.59985 -5.485 8.07 -13.555 -5 -8.555 Pass 189 37.57800 -13.423 8.07 -21.493 -13 -8.493 Pass 37.59995 -4.835 8.07 -12.905 -5 -7.905 Pass 40+164 37.57745 -13.392 8.07 -21.462 -13 -8.462 Pass 37.59985 -2.402 8.07 -10.472 -5 -5.472 Pass 58+184 37.58965 -13.082 8.07 -21.152 -13 -8.152 Pass 37.59975 -5.475 8.07 -13.545 -5 -8.545 Pass 61+189 37.58970 -13.606 8.07 -21.676 -13 -8.676 Pass Note: The Conducted Power = EIRP-Array Gain Report No.: RF190401E07-6 Page No. 373 / 415 Report Format Version: 6.1.1

Beam 164 Beam 184 Beam 189 Beam 40+164 Beam 58+184 Beam 61+189 Report No.: RF190401E07-6 Page No. 374 / 415 Report Format Version: 6.1.1

Lowest-edge Band n260 Component Carriers 4CC Modulation QPSK RB 1RB0 Conducted Frequency EIRP Value Array Gain Limit Margin Beam ID Power Result (GHz) (dBm) (dBi) (dBm) (dB) (dBm) 37.59985 -7.932 8.07 -16.002 -5 -11.002 Pass 164 37.58265 -13.023 8.07 -21.093 -13 -8.093 Pass 37.59995 -8.795 8.07 -16.865 -5 -11.865 Pass 184 37.58855 -13.508 8.07 -21.578 -13 -8.578 Pass 37.59995 -10.266 8.07 -18.336 -5 -13.336 Pass 189 37.58150 -14.753 8.07 -22.823 -13 -9.823 Pass Note: The Conducted Power = EIRP-Array Gain Beam 164 Beam 184 Beam 189 Report No.: RF190401E07-6 Page No. 375 / 415 Report Format Version: 6.1.1

Lowest-edge BAND n260 Component Carriers 1CC MODULATION QPSK RB 66RB Conducted Frequency EIRP Value Array Gain Limit Margin Beam ID Power Result (GHz) (dBm) (dBi) (dBm) (dB) (dBm) 37.59940 -11.532 8.07 -19.602 -5 -14.602 Pass 164 37.58950 -13.583 8.07 -21.653 -13 -8.653 Pass 37.59915 -13.349 8.07 -21.419 -5 -16.419 Pass 184 37.59420 -13.406 8.07 -21.476 -13 -8.476 Pass 37.59950 -13.089 8.07 -21.159 -5 -16.159 Pass 189 37.58050 -12.654 8.07 -20.724 -13 -7.724 Pass 37.59950 -11.685 8.07 -19.755 -5 -14.755 Pass 40+164 37.58750 -12.875 8.07 -20.945 -13 -7.945 Pass 37.59980 -10.490 8.07 -18.560 -5 -13.560 Pass 58+184 37.58755 -13.037 8.07 -21.107 -13 -8.107 Pass 37.59955 -11.954 8.07 -20.024 -5 -15.024 Pass 61+189 37.58625 -12.712 8.07 -20.782 -13 -7.782 Pass Note: The Conducted Power = EIRP-Array Gain Report No.: RF190401E07-6 Page No. 376 / 415 Report Format Version: 6.1.1

Beam 164 Beam 184 Beam 189 Beam 40+164 Beam 58+184 Beam 61+189 Report No.: RF190401E07-6 Page No. 377 / 415 Report Format Version: 6.1.1

Lowest-edge BAND n260 Component Carriers 2CC MODULATION QPSK RB 66RB Conducted Frequency EIRP Value Array Gain Limit Margin Beam ID Power Result (GHz) (dBm) (dBi) (dBm) (dB) (dBm) 37.59520 -12.666 8.07 -20.736 -5 -15.736 Pass 164 37.58940 -13.013 8.07 -21.083 -13 -8.083 Pass 37.59695 -13.477 8.07 -21.547 -5 -16.547 Pass 184 37.57970 -12.753 8.07 -20.823 -13 -7.823 Pass 37.59570 -15.090 8.07 -23.160 -5 -18.160 Pass 189 37.59215 -14.605 8.07 -22.675 -13 -9.675 Pass 37.59950 -11.741 8.07 -19.811 -5 -14.811 Pass 40+164 37.59050 -11.244 8.07 -19.314 -13 -6.314 Pass 37.59790 -12.917 8.07 -20.987 -5 -15.987 Pass 58+184 37.59060 -11.857 8.07 -19.927 -13 -6.927 Pass 37.59985 -10.996 8.07 -19.066 -5 -14.066 Pass 61+189 37.59105 -12.105 8.07 -20.175 -13 -7.175 Pass Note: The Conducted Power = EIRP-Array Gain Report No.: RF190401E07-6 Page No. 378 / 415 Report Format Version: 6.1.1

Beam 164 Beam 184 Beam 189 Beam 40+164 Beam 58+184 Beam 61+189 Report No.: RF190401E07-6 Page No. 379 / 415 Report Format Version: 6.1.1

Lowest-edge BAND n260 Component Carriers 4CC MODULATION QPSK RB 66RB Conducted Frequency EIRP Value Array Gain Limit Margin Beam ID Power Result (GHz) (dBm) (dBi) (dBm) (dB) (dBm) 37.59895 -12.608 8.07 -20.678 -5 -15.678 Pass 164 37.58260 -11.528 8.07 -19.598 -13 -6.598 Pass 37.59985 -12.586 8.07 -20.656 -5 -15.656 Pass 184 37.58505 -12.550 8.07 -20.620 -13 -7.620 Pass 37.59620 -11.873 8.07 -19.943 -5 -14.943 Pass 189 37.59170 -12.768 8.07 -20.838 -13 -7.838 Pass Note: The Conducted Power = EIRP-Array Gain Beam 164 Beam 184 Beam 189 Report No.: RF190401E07-6 Page No. 380 / 415 Report Format Version: 6.1.1


Document Created: 2019-07-09 02:44:49
Document Modified: 2019-07-09 02:44:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC