Modular Approval Request

FCC ID: NKR-KM66

Cover Letter(s)

Download: PDF
FCCID_3031681

                                                                                                             RF_734_02
                                                                                                            04 April 16


Modular Approval Request FCC (KDB 996369 D01 & Part 15.212)
FCC ID: NKR-KM66

 Items to be covered by Single modular transmitters.                                       Answer from applicant
 1. The modular transmitter must have its own RF shielding.                                The modular has a shielding
                                                                                           Case. Please refer to EUT
                                                                                           Photo.
 2.   The modular transmitter must have buffered modulation/data inputs (if such inputs    The component number is
      are provided) to ensure that the module will comply with Part 15 requirements        BCM43566PKFFBG
      under conditions of excessive data rates or over-modulation.
 3.   The modular transmitter must have its own power supply regulation.                   The component number is
                                                                                            AX3701Z6A_DFN6P
 4.   The modular transmitter must comply with the antenna requirements of Section         No antenna connector is used.
      15.203 and 15.204(b)(c). The antenna must either be permanently attached or          And no external amplifier will
      employ a “unique” antenna coupler (at all connections between the module and the     be used with this modular.
      antenna, including the cable).

 5.   The modular transmitter must be tested in a stand-alone configuration, i.e., the     This modular is tested under
      module must not be inside another device during testing. This is intended to         stand-alone configuration.
      demonstrate that the module is capable of complying with Part 15 emission limits     Please refer to Test setup
      regardless of the device into which it is eventually installed.                      photo.

 6. The modular transmitter must be equipped with either a permanently affixed label       The modular transmitter is
    or must be capable of electronically displaying its FCC identification number in       labeled with its own FCC ID
    accordance with 15.212 (a)(1)(vi)(A) / (B).                                            number. Please refer to label
                                                                                           sample and label location.
 7. The modular transmitter must comply with any specific rule or operating                The modular complies with
    requirements applicable to the transmitter and the manufacturer must provide            this requirement. Please refer
    adequate instructions along with the module to explain any such requirements. A         to user manual.
    copy of these instructions must be included in the application for equipment
    authorization. For example, there are very strict operational and timing
    requirements that must be met before a transmitter is authorized for operation under
    Section 15.231. For instance, data transmission is prohibited, except for operation
    under Section 15.231(e), in which case there are separate field strength level and
    timing requirements. Compliance with these requirements must be assured.

 8.   The modular transmitter must comply with any applicable RF exposure                  The device complies with this
      requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and         requirement. Please refer to
      specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and          RF exposure report.
      15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices
      perform routine environmental evaluation for RF Exposure to demonstrate
      compliance. In addition, spread spectrum transmitters operating under Section
      15.247 are required to address RF Exposure compliance. Modular transmitters
      approved under other Sections of Part 15, when necessary, may also need to
      address certain RF Exposure concerns, typically by providing specific
      installation and operating instructions for users, installers and other interested
      parties to ensure compliance.


Note: A limited modular approval (LMA) may be granted for single or split modular transmitters
that comply partially with the requirements above.



Date: ___17 June 2016____                   Signature: ___________________________



Document Created: 2017-12-08 13:40:03
Document Modified: 2017-12-08 13:40:03

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC