Modular Approval Request

FCC ID: NKR-DNUAPO1

Cover Letter(s)

Download: PDF
FCCID_2379475

RF_734_00, Issue 1 Modular Approval Request FCC (per DA 00-1407) FCC ID: NKR-DNUAPO1 Items to be covered Answer from applicant 1. The modular transmitter must have its own RF shielding. The modular has a shielding Case. Please refer to EUT Photo. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs The component number is are provided) to ensure that the module will comply with Part 15 requirements AR9375 under conditions of excessive data rates or over-modulation. 3. The modular transmitter must have its own power supply regulation. The component number is AR9375 / AX3503Z6A 4. The modular transmitter must comply with the antenna requirements of Section Antenna connector is MCX. 15.203 and 15.204(c). The antenna must either be permanently attached or employ And no external amplifier will a “unique” antenna coupler (at all connections between the module and the antenna, be used with this modular. including the cable).. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the This modular is tested under module must not be inside another device during testing. This is intended to stand-alone configuration. demonstrate that the module is capable of complying with Part 15 emission limits Please refer to Test setup regardless of the device into which it is eventually installed. photo. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the The modular transmitter is FCC ID is not visible when the module is installed inside another device, then the labeled with its own FCC ID outside of the device into which the module is installed must also display a label number. Please refer to label referring to the enclosed module. This exterior label can use wording such as the sample and label location. following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating The modular complies with requirements applicable to the transmitter and the manufacturer must provide this requirement. Please refer adequate instructions along with the module to explain any such requirements. A to user manual. copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure The device complies with this requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific requirement. Please refer to Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), RF exposure report. require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA). Name and surname of applicant (or authorized representative): __________________ Date: ___29 August 2014____ Signature: ___________________________


Document Created: 2019-09-13 10:11:20
Document Modified: 2019-09-13 10:11:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC