User Manual

FCC ID: NKR-CB1GI21M2

Users Manual

Download: PDF
FCCID_3819983

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 1 OF 22 UMC-I21M2 User Manual Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 2 OF 22 Revision History Issue Date Version Description 2018/01/29 1.0 Initial Issued 2018/02/09 1.1 Add LTE antenna 2018/02/26 1.2 Add ZB test Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 3 OF 22 Contents 1. Introduction ............................................................................................................................................ 4 2. Test Setup Configuration ....................................................................................................................... 5 2.1 Power Supply and Debug Console Connection ......................................................................... 5 i. Top view of UMC-I21M2 ...................................................................................................... 5 ii. Bottom view of UMC-I21M2 ................................................................................................ 5 iii. Interface board ....................................................................................................................... 6 iv. Connection between interface board and UMC-I21M2......................................................... 7 2.2 Antenna Connection................................................................................................................... 9 2.3 Hardware Component Introduction ......................................................................................... 10 3. LTE B13 Test and ZB Test ................................................................................................................... 12 3.1 Install Qualcomm USB driver ................................................................................................ 13 3.2 Confirm the Qualcomm device .............................................................................................. 13 3.3 Enter ADB shell ....................................................................................................................... 14 3.4 ZigBee Test Command ............................................................................................................ 15 4. Interfaces .............................................................................................................................................. 16 4.1 Qualcomm HS-USB MDM Diagnostics 90B2 (COM port) .................................................... 16 4.2 Qualcomm HS-USB WWAN Adapter 90B2 ........................................................................... 17 4.3 Qualcomm HS-USB Modem 90B2 ......................................................................................... 17 5. Federal Communication Commission Interference Statement ............................................................ 19 6. Appendix I ........................................................................................................................................... 22 Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 4 OF 22 1. Introduction This User Manual of UMC-I21M2 is to describe how to use the following sections for lab test by specific qualified engineers or technicians. Furthermore, this SMCC (Smart Metering Communication Card) is NOT intended for commercial use but designed as part of Smart Meter product which mainly provides 4G LTE WAN access. For the procedure of SMCC installation and set-up for testing and operating, the information is described as well in the following description. FCC Interference Statement This module complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This module may not cause harmful interference and (2) this module must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement This module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This module should be installed and operated with minimum distance of 20cm between radiator and human body. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 5 OF 22 2. Test Setup Configuration 2.1 Power Supply and Debug Console Connection i. Top view of UMC-I21M2 Debug USB LTE module connector ii. Bottom view of UMC-I21M2 SIM slot Make sure to insert the SIM card for LTE test. Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 6 OF 22 iii. Interface board Make sure the jumpers are in right position. Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 7 OF 22 iv. Connection between interface board and UMC-I21M2 UMC-I21M2 OFF ON 12 pin Meter connector Interface Board Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 8 OF 22 USB Debug Port Console Power switch AC-DC 5V Adaptor Interface Board Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 9 OF 22 Power on Sequence: I. Connect UMC-I21M2 to interface board II. Attach AC-DC Adaptor & USB Debug Port Cable III. Turn on the power switch IV. System will be accessible after waiting 20 seconds 2.2 Antenna Connection The Connector of LTE Antenna Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 10 OF 22 Connector for ZigBee conducted test 2.3 Hardware Component Introduction UMC-I21M2 Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 11 OF 22 AC-DC 5V Adaptor Interface Board UMC-I21M2 LTE Antenna Antenna with holder Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 12 OF 22 3. LTE B13 Test and ZB Test It is recommended to use Anritsu MT8821C for RF conductive tests.setc In the field, please use Qualcomm tool, QXDM, and AT-command to control device and log device message. For LTE radiation tests, the LTE antenna gain lists below.  LTE Main Antenna  Band 13 Peak Gain: 1.5dBi~2.49dBi Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 13 OF 22 3.1 Install Qualcomm USB driver Install the Qualcomm USB driver & ADB driver 3.2 Confirm the Qualcomm device Confirm the Android Device “Android Comosite ADB interface” Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 14 OF 22 3.3 Enter ADB shell Command in Command Prompt: adb shell Command in adb shell: cat /etc/gridnet-release Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 15 OF 22 3.4 ZigBee Test Command Enter Zigbee control mode: ember-mfgtool Set mfg start: mfg start 1 Freq. channel setting: mfg channel set 11 Channel Low : 11 -> CH11 Channel Mid : 18 -> CH18 Channel High : 25 -> CH25 Power level/mode setting: mfg power set -3 mode 2 Single tone output: mfg tone start Single tone output stop: mfg tone stop Modulation signal output: mfg stream start Modulation signal output stop : mfg stream stop Exit: <Ctrl>+<X> <Enter> Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 16 OF 22 4. Interfaces This SMCC offers following interfaces to communicate with module. Before using USB emulated ports, it requires to install the Qualcomm’s USB driver on your windows PC in advance. After driver installation is finished, device manager will show below USB emulated COM ports. 4.1 Qualcomm HS-USB MDM Diagnostics 90B2 (COM port) This port is created for modem debugging purpose and used by Qualcomm PC tools to communicate with the module. Qualcomm’s tool is protected by Qualcomm License. Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 17 OF 22 4.2 Qualcomm HS-USB WWAN Adapter 90B2 This port is created as a virtual network interface which could be used by PC to connect with Internet. 4.3 Qualcomm HS-USB Modem 90B2 This port is also called as modem port. Testers could use PC terminal tool to connect with the port and send AT commands to control modem directly. Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 18 OF 22 Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 19 OF 22 5. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio technician for help. Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 20 OF 22 FCC Caution:  Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.  This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and the maximum antenna gain allowed for use with this device is +2.49 dBi. 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 21 OF 22 End Product Labeling: This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: NKR-CB1GI21M2”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information to the End User: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Wistron Neweb Corporation Proprietary & Confidential

Design Document Subject: UMC-I21M2 User Manual REV: 1.0 PAGE 22 OF 22 6. Appendix I Environmental Setup 1. Windows 7 x64 The environment setup was tested on Windows 7 x64 successfully. 2. USB driver QUD.WIN.1.1 Installer will be needed to be installed for the following ports:  Qualcomm HS-USB MDM Diagnostics 90B2  Qualcomm HS-USB MDM WWAN Adapter 90B2  Qualcomm USB Composite Device 90B2  QDSS Data 90B2  Qualcomm HS-USB Modem 90B2 3. ADB driver http://adbdriver.com/ 4. ADB shell Wistron Neweb Corporation Proprietary & Confidential


Document Created: 2018-04-17 17:17:12
Document Modified: 2018-04-17 17:17:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC