Test report_NFC

FCC ID: NDPM3A-2

Test Report

Download: PDF
FCCID_4312908

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 RADIO TEST REPORT Applicant : Partner Tech Corp. 10FL, 233-2, Baoqiao Road, Xindian, Address : New Taipei City, Taiwan Equipment : Mobile POS Terminal M3a-2, EM-110, EMC-21X0 (X could be 0-9, -, A-Z or Model No. : blank ) Trade Name : PARTNER FCC ID : NDPM3A-2 I HEREBY CERTIFY THAT : The sample was received on Jan. 17, 2019 and the testing was carried out on Mar. 05, 2019 at Cerpass Technology Corp. The test result refers exclusively to the test presented test model / sample. Without written approval of Cerpass Technology Corp., the test report shall not be reproduced except in full. Approved by: Tested by: Mark Liao / Supervisor Spree Yeh / Engineer Laboratory Accreditation: Cerpass Technology Corporation Test Laboratory Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 1 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 Contents 1. Summary of Test Procedure and Test Results ................................................................................. 4 1.1. Applicable Standards ................................................................................................................. 4 2. Test Configuration of Equipment under Test ................................................................................... 5 2.1. Feature of Equipment under Test ............................................................................................... 5 2.2. Model Difference ........................................................................................................................ 5 2.3. Carrier Frequency of Channels .................................................................................................. 6 2.4. Test Mode and Test Software ..................................................................................................... 6 2.5. Description of Test System ......................................................................................................... 6 2.6. General Information of Test ........................................................................................................ 7 2.7. Measurement Uncertainty .......................................................................................................... 7 3. Test Equipment and Ancillaries Used for Tests ............................................................................... 8 4. Antenna Requirements ....................................................................................................................... 9 4.1. Standard Applicable ................................................................................................................... 9 4.2. Antenna Construction and Directional Gain ............................................................................... 9 5. Test of AC Power Line Conducted Emission ................................................................................. 10 5.1. Test Limit .................................................................................................................................. 10 5.2. Test Procedures ....................................................................................................................... 10 5.3. Typical Test Setup .................................................................................................................... 11 5.4. Test Result and Data ................................................................................................................ 12 5.5. Test Photographs ..................................................................................................................... 14 6. Test of Radiated Emission ............................................................................................................... 15 6.1. Test Limit .................................................................................................................................. 15 6.2. Test Procedures ....................................................................................................................... 16 6.3. Typical Test Setup Layout of Radiated Emission ..................................................................... 17 6.4. Test Result and Data ................................................................................................................ 18 6.5. 20dB Bandwidth & 99% Occupied Bandwidth ......................................................................... 24 6.6. Test Photographs (9KHz ~ 30MHz) ......................................................................................... 26 6.7. Test Photographs (30MHz ~ 1GHz) ......................................................................................... 27 7. Frequency Stability ........................................................................................................................... 28 7.1. Test Procedure ......................................................................................................................... 28 7.2. Test Setup Layout .................................................................................................................... 28 7.3. Test Result and Data ................................................................................................................ 29 Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 2 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 History of this test report Report No. Issue Date Description TEFO1901083 Mar. 14, 2019 Original Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 3 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 1. Summary of Test Procedure and Test Results 1.1. Applicable Standards ANSI C63.4:2014 FCC Rules and Regulations Part 15 Subpart C §15.225 FCC Rule Description of Test Result 15.203 Antenna Requirement PASS 15.207 AC Power Line Conducted Emission PASS 15.209 Radiated Emission PASS 15.225 15.225 20dB Bandwidth PASS 15.225(e) Frequency Stability PASS This EUT has been also tested and complied with the requirement of FCC Part 15, Subpart B, recorded in a separate test report (TEFV1901083). Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 4 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 2. Test Configuration of Equipment under Test 2.1. Feature of Equipment under Test Item M3a-2 Processor Qualcomm® APQ8053 Processor OS Android 7.1 Memory/Storage Standard 4G/32G Display 10.1", 1280 x 800, 350nits Touch Projected capacitive touch (Multi Touch) Bluetooth V4.1 WiFi 802.11 a/b/g/n/ac mini-PCIE for LTE support Standard SIM slot WWAN (optional) For data, GPRS/EDGE/WCDMA/LTE(Module: Quectel_EC25 series) GPS (optional) For GPS, GLONASS , Beidou and Galileo E-compass (Optional) Sensor Ambient Light Gyroscope Battery Rechargeable Li-ion battery 7.4V, 4600mAh Working time 6 hours, Video playback, 50% brightness & Volume, BT & WIFI on Speaker Internal, 2*2W 1* USB 2.0 TYPE A 1* Micro SD card, Max. 128G 1* Micro HDMI I/O 1* SIM slot 1* DC Jack 1* Audio Jack Rear Camera: 8M, Auto focus Camera Front Camera: 2M LEDs 1* red/green LED for power & system status Dimension W x L x T: 278mm x 199mm x 20.9mm Operation temperature 0°C ~ 40°C Temperature Storage temperature -20°C ~ 60°C Humidity 15% to 85% (no condensation) Sealing IP54 Drop specification 1M Optional Device Module 2D barcode scanner (image); IC card reader ISO7816; NFC; (Factory optional) MSR ISO7811-Track 1, 2, 3; Fingerprint 512dpi NFC Frequency Range 13.56MHz Antenna Type/gain Loop Antenna / 1dBi EDAC \ EA1024P1 Adapter Input: 100-240Vac, 1A, 50-60Hz Output: 12Vdc, 3A 2.2. Model Difference M3a-2, EM-110, EMC-21X0 (X could be 0-9, -, A-Z or blank) for marketing purpose. Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 5 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 2.3. Carrier Frequency of Channels Channel Frequency(MHz) *1 13.56 Note: Channel remarked “*” is selected to perform test. 2.4. Test Mode and Test Software a. During testing, the interface cables and equipment positions were varied according to ANSI C63.10. b. The complete test system included NB and EUT for RF test. c. An executive program, “Tag writer “was executed to transmit and receive data through NFC. d. The test mode of RF test as follow: Test Mode 1. NFC, 13.56MHz , Adapter:EDAC \ EA1024P1 2.5. Description of Test System Device Manufacturer Model No. Description Notebook ASUS P2430U Power Cable, Non-shielded, 1.8m Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 6 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 2.6. General Information of Test Cerpass Technology Corporation Test Laboratory Address: No.10, Ln. 2, Lianfu St., Luzhu Dist., Taoyuan City 33848, Taiwan (R.O.C.) Tel:+886-3-3226-888 Fax:+886-3-3226-881 Test Site Address: No.68-1, Shihbachongsi, Shihding Township, New Taipei City 223, Taiwan, R.O.C. Tel: +886-2-2663-8582 FCC TW1079, TW1061, W1439 IC 4934E-1, 4934E-2 T-2205 for Telecommunication test C-4663 for Conducted emission test VCCI R-4399, R-4218 for Radiated emission test G-10812, G-10813 for radiated disturbance above 1GHz Frequency Range Conducted: from 150kHz to 30 MHz Investigated: Radiation: from 30 MHz to 10,000MHz Test Distance: The test distance of radiated emission from antenna to EUT is 3 M. 2.7. Measurement Uncertainty Measurement Item Uncertainty Radiated Spurious Emission(9KHz~30MHz) ±5.007dB Radiated Spurious Emission(30MHz~1GHz) ±5.157dB Radiated Spurious Emission(1GHz~18GHz) ±6.383dB Radiated Spurious Emission(18GHz~40GHz) ±6.648dB Conducted Spurious Emission ±1.253dB 6dB Bandwidth ±6.89% Power Spectral Density ±0.630dB 26 dB Occupied Bandwidth ±6.10% Frequency Stability ±375KHz Channel Frequencies Separation ±6.10% 20dB Bandwidth ±6.12% Dwell Time ±1.34% Peak Output Power(Conducted Power Meter) ±0.86dB Temperature ±1.2℃ Humidity ±2.7% Channel Move Time ±4.53% Channel Closing Transmission Time ±6.61% Threshold ±0.631dB Non occupancy period ±1.17% Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 7 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 3. Test Equipment and Ancillaries Used for Tests Calibration Instrument Manufacturer Model No. Serial No. Valid Date Date EMI Receiver R&S ESCI3 100821 2018/09/12 2019/09/11 LISN Schwarzbeck NSLK 8127 8127-516 2018/09/11 2019/09/10 Pulse Limiter R&S ESH3-Z2 101933 2018/09/04 2019/09/03 Bilog Antenna Schwarzbeck VULB9168 275 2018/09/17 2019/09/16 Active Loop Antenna EMCO 6507 40855 2018/05/22 2019/05/21 Horn Antenna EMCO 3115 31601 2018/09/26 2019/09/25 Horn Antenna EMCO 3116 31970 2018/03/23 2019/03/22 Preamplifier EM EM330 60659 2018/03/20 2019/03/19 EMC Preamplifier EMC051845SE 980333 2018/09/18 2019/09/17 INSTRUMENTS EMC Preamplifier EMC184045 980065 2018/10/31 2019/10/30 INSTRUMENTS MXG MW Analog KEYSIGHT N5183A MY50142931 2018/04/10 2019/04/09 Signal Generator Spectrum Analyzer R&S FSP40 100219 2018/07/03 2019/07/02 BLUETOOTH R&S CBT 101133 2018/04/02 2019/04/01 TESTER Attenuator KEYSIGHT 8491B MY39250705 2018/09/04 2019/09/03 Rotary Attenuator Agilent 8495B MY42146680 2018/03/29 2019/03/28 Temp & Humi chamber T-MACHINE TMJ-9712 T-12-040111 2018/08/30 2019/08/29 Series Power Meter Anritsu ML2495A 1224005 2018/03/23 2019/03/22 Power Sensor Anritsu MA2411B 1207295 2018/03/23 2019/03/22 Software Farad Ez-EMC ver.ct3a1 N/A N/A Software AUDIX E3 V8.2014-8-6 N/A N/A N7607B Signal Software Keysight V3.0.0.0 N/A N/A Studio Inservice Software Keysight N/A N/A N/A MonitorUtility Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 8 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 4. Antenna Requirements 4.1. Standard Applicable For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.249, if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 4.2. Antenna Construction and Directional Gain Antenna Type Loop Antenna Antenna Gain 1dBi Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 9 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 5. Test of AC Power Line Conducted Emission 5.1. Test Limit Conducted Emissions were measured from 150 kHz to 30 MHz with a bandwidth of 9 KHz, according to the methods defined in ANSI C63.4-2014. The EUT was placed on a nonmetallic stand in a shielded room 0.8 meters above the ground plane. The interface cables and equipment positioning were varied within limits of reasonable applications to determine the position produced maximum conducted emissions. Frequency Quasi Peak Average (MHz) (dB µ V) (dB µ V) 0.15 – 0.5 66-56* 56-46* 0.5 – 5.0 56 46 5.0 – 30.0 60 50 *Decreases with the logarithm of the frequency. 5.2. Test Procedures a. The EUT was placed 0.4 meter from the conducting wall of the shielding room was kept at least 80 centimeters from any other grounded conducting surface. b. Connect EUT to the power mains through a line impedance stabilization network (LISN). c. All the support units are connecting to the other LISN. d. The LISN provides 50 ohm coupling impedance for the measuring instrument. e. The FCC states that a 50 ohm, 50 micro-Henry LISN should be used. f. Both sides of AC line were checked for maximum conducted interference. g. The frequency range from 150 kHz to 30 MHz was searched. h. Set the test-receiver system to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 10 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 5.3. Typical Test Setup 10cm EUT Adapter 80cm 80cm AC Line 80cm 40cm LISN LISN 40cm Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 11 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 5.4. Test Result and Data Power : AC 120V Pol/Phase : LINE Test Mode : Mode 1 Temperature : 22 °C Test date : Mar. 05, 2019 Humidity : 52 % Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 12 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 Power : AC 120V Pol/Phase : NEUTRAL Test Mode : Mode 1 Temperature : 22 °C Test date : Mar. 05, 2019 Humidity : 52 % Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 13 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 6. Test of Radiated Emission 6.1. Test Limit (a) The field strength of any emissions within the band 13.553-13.567 MHz shall not exceed 15,848 microvolts/meter at 30 meters. (b) Within the bands 13.410-13.553 MHz and 13.567-13.710 MHz, the field strength of any emissions shall not exceed 334 microvolts/meter at 30 meters. (c) Within the bands 13.110-13.410 MHz and 13.710-14.010 MHz the field strength of any emissions shall not exceed 106 microvolts/meter at 30 meters. (d) The field strength of any emissions appearing outside of the 13.110-14.010 MHz band shall not exceed the general radiated emission limits in §15.209. Frequency (MHz) Distance Limit (μV/ m) 0.09 ~ 0.490 300m 2400/F(kHz) 0.490 ~ 1.705 30m 24000/ F(kHz) 1.705 ~ 30 30m 30 30 ~ 88 3m 100 88 ~ 216 3m 150 216 ~ 960 3m 200 Above 960 3m 500 15.215 Additional provisions to the general radiated emission limitations.: (c) Intentional radiators operating under the alternative provisions to the general emission limits, as contained in §§15.217 through 15.257 and in subpart E of this part, must be designed to ensure that the 20 dB bandwidth of the emission, or whatever bandwidth may otherwise be specified in the specific rule section under which the equipment operates, is contained within the frequency band designated in the rule section under which the equipment is operated. Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 15 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 6.2. Test Procedures a. The EUT was placed on a rotatable table top 0.8 meter above ground. b. The EUT was set 3 meters from the interference receiving antenna which was mounted on the top of a variable height antenna tower. c. The table was rotated 360 degrees to determine the position of the highest radiation. d. The antenna is a broadband antenna and its height is varied between one meter and four meters above ground to find the maximum value of the field strength both horizontal polarization and vertical polarization of the antenna are set to make the measurement. e. For each suspected emission the EUT was arranged to its worst case and then tune the antenna tower (from 1 M to 4 M) and turn table (from 0 degree to 360 degrees) to find the maximum reading. f. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function and specified bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 3 dB lower than the limit specified, then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 3 dB margin will be repeated one by one using the quasi-peak method and reported. h. “Cone of radiation” has been considered to be 3dB beamwidth of the measurement antenna. NOTE: 1. The resolution bandwidth of test receiver/spectrum analyzer is 300Hz or CISPS 200Hz(QP detector) at frequency Below 150 kHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 10KHz or CISPS 9KHz(QP detector) at frequency 150 kHz to 30 MHz. 3. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 16 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 6.3. Typical Test Setup Layout of Radiated Emission Below 30MHz test setup Antenna Equipment under Test 1m * 3m 0.8M Turn Table T bl Ground Plane Receiver Below 1GHz Test Setup Antenna Equipment under Test * 3m 0.8M Turn Table Ground Plane Receiver 1.5M Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 17 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 6.4. Test Result and Data 6.4.1. Test Result of Fundamental Emission Power : AC 120V Loop : Open Test Mode : Mode 1 Temperature : 23°C Test Date : Feb. 19, 2019 Humidity : 61% Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 18 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 Power : AC 120V Loop : Close Test Mode : Mode 1 Temperature : 23°C Test Date : Feb. 19, 2019 Humidity : 61% Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 19 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 6.4.2. Test Result of Unwanted Spurious emission (9KHz ~ 30MHz) Power : AC 120V Loop : Open Test Mode : Mode 1 Temperature : 23°C Test Date : Feb. 19, 2019 Humidity : 61% Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 20 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 Power : AC 120V Loop : Close Test Mode : Mode 1 Temperature : 23°C Test Date : Feb. 19, 2019 Humidity : 61% Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 21 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 6.4.3. Test Result of Unwanted Spurious emission (30GHz ~ 1GHz) Power : AC 120V Pol/Phase : VERTICAL Test Mode : Mode 1 Temperature : 23°C Test Date : Feb. 19, 2019 Humidity : 61% Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 22 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 Power : AC 120V Pol/Phase : HORIZONTAL Test Mode : Mode 1 Temperature : 23°C Test Date : Feb. 19, 2019 Humidity : 61% Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 23 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 6.5. 20dB Bandwidth & 99% Occupied Bandwidth Ch. Freq. 20dB Bandwidth FL at 20dB BW FH at 20dB BW 99% Bandwidth (MHz) (kHz) (MHz) (MHz) (kHz) 13.56 4.24 13.55876 13.563 9.360 20dB Bandwidth 13.56 MHz * RBW 1 kHz Marker 2 [T1 ] * VBW 3 kHz 31.52 dBµV Ref 90 dBµV * Att 10 dB SWT 20 ms 13.563000000 MHz 90 Marker 1 [T1 ] 31.36 dBµV 13.558760000 MHz A 80 1 PK VIEW 70 60 PS 50 40 1 2 3DB D1 31.61 dBµV 30 AC 20 10 0 -10 Center 13.5608 MHz 2 kHz/ Span 20 kHz Date: 5.MAR.2019 09:16:09 Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 24 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 99% Bandwidth 13.56 MHz * RBW 1 kHz Marker 1 [T1 ] * VBW 3 kHz 51.58 dBµV Ref 90 dBµV * Att 10 dB SWT 20 ms 13.560800000 MHz 90 OBW 9.360000000 kHz Temp 1 [T1 OBW] 26.05 dBµV A 80 13.556160000 MHz 1 SA * Temp 2 [T1 OBW] VIEW 70 25.22 dBµV 13.565520000 MHz 60 1 PS 50 40 3DB 30 AC T1 T2 20 10 0 -10 Center 13.5608 MHz 2 kHz/ Span 20 kHz Date: 5.MAR.2019 09:20:05 Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 25 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 7. Frequency Stability 7.1. Test Procedure 1. The EUT was placed inside the Temperature and Humidity chamber. 2. The transmitter output was connected to spectrum analyzer. 3. Turn the EUT on and couple its output to a spectrum analyzer. 4. Turn the EUT off and set the chamber to the highest temperature specified. 5. Allow sufficient time (approximately 30 min) for the temperature of the chamber to stabilize, turn the EUT on and measure the operating frequency after 2, 5, and 10 minutes. 6. Repeat step 2 and 3 with the temperature chamber set to the lowest temperature. 7. The test chamber was allowed to stabilize at +20 degree C for a minimum of 30 minutes. The supply voltage was then adjusted on the EUT from 85% to 115% and the frequency record. 7.2. Test Setup Layout Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 28 of 29 FCC ID. : NDPM3A-2

CERPASS TECHNOLOGY CORP. Report No.: TEFO1901083 7.3. Test Result and Data Operating frequency: 13.56 MHz Power 2 minute 5 minute 10 minute Temp(°C) supply(V) (MHz) (%) (MHz) (%) (MHz) (%) 102 13.56098 0.007227 13.56102 0.007522 13.56100 0.007375 40 120 13.56099 0.007301 13.56098 0.007227 13.56099 0.007301 138 13.56100 0.007375 13.56099 0.007301 13.56100 0.007375 102 13.56099 0.007301 13.56100 0.007375 13.56102 0.007522 30 120 13.56098 0.007227 13.56101 0.007448 13.56100 0.007375 138 13.56100 0.007375 13.56100 0.007375 13.56098 0.007227 102 13.56102 0.007522 13.56099 0.007301 13.56100 0.007375 20 120 13.56101 0.007448 13.56097 0.007153 13.56102 0.007522 138 13.56102 0.007522 13.56098 0.007227 13.56100 0.007375 102 13.56098 0.007227 13.56099 0.007301 13.56101 0.007448 10 120 13.56099 0.007301 13.56097 0.007153 13.56098 0.007227 138 13.56100 0.007375 13.56099 0.007301 13.56099 0.007301 102 13.56100 0.007375 13.56099 0.007301 13.56098 0.007227 0 120 13.56101 0.007448 13.56100 0.007375 13.56099 0.007301 138 13.56100 0.007375 13.56099 0.007301 13.56098 0.007227 Cerpass Technology Corp. Issued date : Mar. 14, 2019 T-FD-504-0 Ver 1.0 Page No. : 29 of 29 FCC ID. : NDPM3A-2


Document Created: 2019-05-29 15:48:12
Document Modified: 2019-05-29 15:48:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC