User Manual-GAP-429HOB

FCC ID: NDD9574291705

Users Manual

Download: PDF
FCCID_3693531

Quick Installation Guide AC1300 Outdoor AP GAP-429HOB Quick Installation Guide 05-2016 / v1.0

I. Product Information I-1. Package Contents 1 2 3 4 5 6 1. Access Point 5. Pole Mount Ties 2. Quick Installation Guide 6. Antenna 3. Ethernet Cable 4. Wall Mount Screws Kits 2

I-2. System Requirements - Existing Ethernet cable, IEEE802.3at PoE Switch - Computer with web browser for access point configuration I-3. Hardware Overview B A C D A. LAN1 port with Power over Ethernet (IEEE802.3at PoE PD-IN). B. LAN2 port with Power over Ethernet (IEEE802.3af PoE PSE-OUT). C. Reset Button. D. Grounding Terminal. 3

I-4. LED Status LED Behavior ON 5G Wireless is enabled. 5G Off 5G Wireless is disabled. ON 2.4G Wireless is enabled. 2.4G Off 2.4G Wireless is disabled. ON LAN2 port is connected. LAN2(PSE) Flashing Traffic is passing through Ethernet port. Off LAN2 port is unconnected. ON LAN1 port is connected. LAN1(PD) Flashing Traffic is passing through Ethernet port. Off LAN1 port is unconnected. ON Booting up process Status Off No error occur ON The access point is on. Power Flashing Long Flashing: Firmware upgrading Off The access point is off. 4

I-5. Reset If you experience problems with your access point, you can reset the device back to its factory settings. This resets all settings back to default. 1. Press and hold the reset button on the access point for at least 10 seconds. Then release the button. You may need to use a pencil or similar sharp object to push the reset button. 2. Wait for the access point to restart. The access point is ready for setup when the Status LED is OFF. I-6. Mounting The access point includes a mount for wall or pole which requires some assembly. Wall Mount 1. Attach the access point to a wall using the included screws and plugs. 5

Pole Mount 1. Fix the access point to a pole using the included stainless tie. Attention: This product is installed in restricted access location by professionals. II. Quick Setup The AC1300 Outdoor AP/CPE features a range of powerful functions: - AC1300 high-speed wireless technology - 16 SSIDs for management - SNMP v1/v2c/v3 Your access point can be up and running in just a few minutes. It can function as a standalone access point (AP mode), as part of an AP array (Managed AP mode), or as a client bridge for WISP last-mile services (Client Bridge mode). 6

II-1. Initial Setup Do not connect a non-PoE device to the access point’s LAN2 (PoE- OUT) port. The LAN2 port outputs 48V and can damage a non PoE device. 1. Connect the access point’s LAN1 (PoE-IN) port to the PoE Switch via Ethernet cable. 2. Wait a moment for the access point to start up. The access point is ready when the Status LED is OFF. 3. Use an Ethernet cable to connect your computer to the access point’s LAN2 port for initial setup. 7

II-2. AP Mode 1. Enter the access point’s IP address into the URL bar of a web browser. The default IP is 192.168.2.2. If the AP is connected to a DHCP server, ensure you use the correct address. 2. You will be prompted for a user name and password. Enter the default username “admin” and the default password “1234”. 3. You will arrive at the “System Information” screen shown below. The next steps will help you to configure the following basic settings of the access point: 8

- LAN IP Address - 2.4G/5GHz SSID & Security - Administrator Name & Password - Time & Date It is recommended you configure these settings before using the access point. 1. To change the access point’s LAN IP address, go to “Network Settings” > “LAN-side IP Address” and you will see the screen below. 2. Enter the IP address settings you wish to use for your access point. You can use a dynamic (DHCP) or static IP address, depending on your network environment. Click “Apply” to save the changes and wait a few moments for the access point to reload. When you change your access point’s IP address, you need to use the new IP address to access the browser based configuration interface instead of the default IP 192.168.2.2. 3. To change the SSID of your access point’s 5GHz wireless network(s), go to “Wireless Settings” > “5GHz 11ac” > “Basic”. Enter the new SSID for your 5GHz wireless network in the “SSID1” field and click “Apply”. To utilize multiple 5GHz SSIDs, open the drop down menu labelled “Enable SSID number” and select how many SSIDs you require. 9

Then enter a new SSID in the corresponding numbered fields below, before clicking “Apply”. 4. To configure the security of your access point’s 5GHz wireless network(s), go to “Wireless Settings” > “5GHz 11ac 11an” > “Security”. Select an “Authentication Method” and enter a “Pre-shared Key” or “Encryption Key” depending on your choice, then click “Apply”. If using multiple SSIDs, specify which SSID to configure using the “SSID” drop down menu. 10

5.To change the SSID of your access point’s 2.4GHz wireless network(s), go to “Wireless Settings” > “2.4GHz 11ac” > “Basic”. Enter the new SSID for your 5GHz wireless network in the “SSID1” field and click “Apply”. To utilize multiple 2.4GHz SSIDs, open the drop down menu labelled “Enable SSID number” and select how many SSIDs you require. Then enter a new SSID in the corresponding numbered fields below, before clicking “Apply”. 6.To configure the security of your access point’s 2.4GHz wireless network(s), go to “Wireless Settings” > “2.4GHz 11ac 11an” > “Security”. Select an “Authentication Method” and enter a “Pre-shared Key” or “Encryption Key” depending on your choice, then click “Apply”. 11

If using multiple SSIDs, specify which SSID to configure using the “SSID” drop down menu. 7. To change the administrator name and password for the browser based configuration interface, go to “Management” > “Admin”. 8. Complete the “Administrator Name” and “Administrator Password” fields and click “Apply”. 9. To set the correct time for your access point, go to “Management” > “Date and Time Settings”. 12

10. Set the correct time and time zone for your access point using the drop down menus. The access point also supports NTP (Network Time Protocol) so alternatively you can enter the host name or IP address of a time server. Click “Apply” when you are finished. You can use the “Acquire Current Time from your PC” button if you wish to set the access point to the same time as your PC. 11. The basic settings of your access point are now configured. 13

III. Hardware Specification Hardware Specification MCU/RF Qualcomm Atheros IPQ 4018 Quad-Core 710MHz Memory DDR3 256MB Flash SPI NOR 32MB Physical - LAN1: Gigabit Ethernet with IEEE802.3at PoE PD-IN support Interface - LAN2: Gigabit Ethernet with IEEE802.3af PoE PSE-OUT support - Reset Button x 1 - Grounding Terminal x 1 - RP-SMA Connector x 2 Power IEEE802.3at Power over Ethernet Requirement Antenna External Dual Band Dipole Antenna x 2 (2.4G: 3dBi, 5G: 4dBi) ENVIRONMENT & PHYSICAL Temperature Range Operation : -40 to 60℃ (-40℉ to 140℉) Storage : -40 to 70℃ (-40℉ to 158℉) Humidity 90% or less – Operating, 90% or less - Storage Certifications FCC, CE, IEC60950-1, IEC60950-22 Dimensions (TBD) 242.27(L) x 120.93(W) x 48.78(D)mm Weight 632g (AP: 594g, Antenna: 38g) International IP5X, IPX6 Protection Rated 14

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. 15


Document Created: 2017-11-10 13:59:36
Document Modified: 2017-11-10 13:59:36
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC