RF Exposure Info

FCC ID: N82-KOHLER035

RF Exposure Info

Download: PDF
FCCID_4418743

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch 588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China Telephone: +86 (0) 21 6191 5666 Report No.: SHEM181200000202 Fax: +86 (0) 21 6191 5678 ee.shanghai@sgs.com Page: 1 of 9 1 Cover Page RF MPE REPORT Application No.: SHEM1812000002CR Applicant: Kohler Co. FCC: N82-KOHLER035 IC ID: 4554A-KOHLER035 Equipment Under Test (EUT): NOTE: The following sample(s) was/were submitted and identified by the client as Product Name: EIR Intelligent Toilet Model No.(EUT): K-77795, K-77795-RGD, K-77795-SG Trade mark: KOHLER Standards: FCC Rules 47 CFR §2.1091 KDB447498 D01 General RF Exposure Guidance v06 RSS-102 Issue 5 (March 2015) Date of Receipt: 2018-12-18 Date of Test: 2018-12-18 to 2018-12-25 Date of Issue: 2019-04-08 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Parlam Zhan E&E Section Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM181200000202 Page: 2 of 9 Revision Record Version Description Date Remark 00 Original 2019-04-10 / Authorized for issue by: Vincent Zhu / Project Engineer Parlam Zhan / Reviewer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM181200000202 Page: 3 of 9 2 Contents Page 1 COVER PAGE................................................................................................................................................. 1 2 CONTENTS ..................................................................................................................................................... 3 3 GENERAL INFORMATION ......................................................................................................................... 4 3.1 CLIENT INFORMATION ................................................................................................................................... 4 3.1 GENERAL DESCRIPTION OF E.U.T.................................................................................................................. 4 3.2 TECHNICAL SPECIFICATIONS ......................................................................................................................... 4 3.3 TEST LOCATION ............................................................................................................................................. 6 3.4 TEST FACILITY............................................................................................................................................... 6 4 TEST STANDARDS AND LIMITS .............................................................................................................. 7 4.1 FCC RADIOFREQUENCY RADIATION EXPOSURE LIMITS: ................................................................................ 7 5 MEASUREMENT AND CALCULATION ................................................................................................... 8 5.1 MAXIMUM TRANSMIT POWER ........................................................................................................................ 8 5.2 MPE CALCULATION ...................................................................................................................................... 9 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM181200000202 Page: 4 of 9 3 General Information 3.1 Client Information Applicant: Kohler Co. Address of Applicant: 444 Highland Drive KOHLER, WI 53044 Manufacturer: Shanghai Kohler Electronics., Ltd. Address of Manufacturer: No. 1955, Fengxiang Road, Baoshan Area, Shanghai, PRC Post code: 200444 Factory: Shanghai Kohler Electronics., Ltd. Address of Factory: No. 1955, Fengxiang Road, Baoshan Area, Shanghai, PRC Post code: 200444 3.1 General Description of E.U.T. Power supply: AC 120V 60Hz 3.2 Technical Specifications 2.4GHz： Modulation Type MSK Number of Channels 8 Operation Frequency 2414.5MHz~2449.5MHz Channel Spacing 5MHz Antenna Type： PCB Antenna Antenna Gain: 2.88 dBi Modulation Type MSK BLE Antenna Gain 0dBi Antenna Type PIFA Antenna Channel Spacing 2MHz Modulation Type GFSK Number of Channels 40 Operation Frequency 2402MHz to 2480MHz 2.4G WiFi Antenna Gain 2dBi Antenna Type PCB Antenna Channel Spacing 5MHz Modulation Type 802.11b: DSSS (CCK, DQPSK, DBPSK) 802.11g/n: OFDM (64QAM, 16QAM, QPSK, BPSK) Number of Channels 802.11b/g/n(HT20):11 Operation Frequency 802.11b/g/n(HT20): 2412MHz to 2462MHz This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM181200000202 Page: 5 of 9 24GHz： Operation Frequency 24.125GHz(24GHz-24.25GHz) Antenna Type PCB Antenna Modulation Type FMCW Number of Channels 1 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM181200000202 Page: 6 of 9 3.3 Test Location All tests were performed at: SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. E&E Lab 588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China Tel: +86 21 6191 5666 Fax: +86 21 6191 5678 No tests were sub-contracted. 3.4 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L0599) CNAS has accredited SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • NVLAP (Certificate No. 201034-0) SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. is accredited by the National Voluntary Laboratory Accreditation Program(NVLAP). Certificate No. 201034-0. • FCC –Designation Number: CN5033 SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been recognized as an accredited testing laboratory. Designation Number: CN5033. Test Firm Registration Number: 479755. • Industry Canada (IC) – IC Assigned Code: 8617A The 3m Semi-anechoic chamber of SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 8617A-1. CAB identifier: CN0020. • VCCI (Member No.: 3061) The 3m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: R-13868, C-14336, T-12221, G-10830 respectively. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM181200000202 Page: 7 of 9 4 Test Standards and Limits 4.1 FCC Radiofrequency radiation exposure limits: According to§1.1310, the limit for general population/uncontrolled exposures Frequency Power density(mW/cm2) Averaging time(minutes) 300MHz~1.5GHz f/1500 30 1.5GHz~100GHz 1.0 30 4.2 IC Radiofrequency radiation exposure limits: According to RSS-102 section 2.5.2, RF exposure evaluation is required if the separation distance between the user and/or bystander and the device’s radiating element is greater than 20 cm, except when the device operates as follows: below 20 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1 W (adjusted for tune-up tolerance); • at or above 20 MHz and below 48 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 4.49/ƒ0.5 W (adjusted for tune-up tolerance), where ƒ is in MHz; • at or above 48 MHz and below 300 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 0.6 W (adjusted for tune-up tolerance); • at or above 300 MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1.31 x 10-2 ƒ0.6834 W (adjusted for tune-up tolerance), where ƒ is in MHz; • at or above 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 5 W (adjusted for tune-up tolerance). For 2.4G device, the limit of worse case is 2.68 W This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM181200000202 Page: 8 of 9 5 Measurement and Calculation 5.1 Maximum transmit power The device using a wireless module (UART CLOUD MODULE) has been certified. The wireless module FCC ID: N82-KOHLER032, IC:4554A–KOHLER032 The max output power: BLE:0.8 mW, WiFi: 48 mW 2.4GHz max output power Base on: SHEM181200000201: Test Frequency Output Power Output Power Reading Power (mW) Polarization (MHz) (dBuV/m) (dBm) 83.27 -12.03 0.06 Horizontal 2414.5 77.8 -17.5 0.02 Vertical 81.88 -13.42 0.05 Horizontal 2434.5 78.05 -17.25 0.02 Vertical 81.17 -14.13 0.04 Horizontal 2449.5 78.2 -17.1 0.02 Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shanghai Branch Report No.: SHEM181200000202 Page: 9 of 9 5.2 MPE Calculation For FCC: PG According to the formula S= , we can calculate S which is MPE. 4R 2 Note: dBm 1) P (Watts) =Power Input to antenna = 10 10 / 1000 2) G (Antenna gain in numeric) = 10^ (Antenna gain in dBi /10) 3) R = distance to the center of radiation of antenna (in meter) = 20cm 4) MPE limit = 1mW/cm² For 2.4GHz : The max E.I.R.P. is 0.06mW, so S=0.00001 <1 mW/cm2 For BLE The max. antenna gain is 0 dBi Max. Gain in Operation Power Conducted Linear Limit Distance Density 2 Result Power Scale (mW/cm ) R(cm) (mW/cm2) P(mW) G 0.8 1.000 20 0.00016 1 Pass For 2.4G WiFi The max. antenna gain is 2 dBi Max. Gain in Operation Power Conducted Linear Limit Distance Density Result Power Scale (mW/cm2) R(cm) (mW/cm2) P(mW) G 48 1.585 20 0.01513 1 Pass The 2.4GHz, BT and the DTS modules can simultaneous transmitting at frequency 2.4GHz band.But the maximum rate of MPE is 0.00001/1+0.00016/1+0.01513/1 =0.015<=1.0. according to the KDB447498 section 7.2 determine the device is exclusion from SAR test. For IC: 2.4GHz: E.I.R.P.=0.00006W＜2.68W BLE: E.I.R.P.= P*G=0.0008W＜2.68W WiFi: E.I.R.P.= P*G=0.076W＜2.68W The 2.4GHz, BT and the DTS modules can simultaneous transmitting at frequency 2.4GHz, But the maximum MPE is 0.00006W+0.076W+0.0008W=0.0768W<2.68W. So the device is exclusion from SAR test. --End of the Report-- This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only


Document Created: 2019-08-29 11:12:07
Document Modified: 2019-08-29 11:12:07
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC