Test Report

FCC ID: N82-KOHLER030

Test Report

Download: PDF
FCCID_3888100

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. 588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China Telephone: +86 (0) 21 6191 5666 Report No.: SHEM180400259201 Fax: +86 (0) 21 6191 5678 Page: 1 of 29 ee.shanghai@sgs.com TEST REPORT Application No.: SHEM1804002592CR Applicant: Kohler Co. Address of Applicant: 444 Highland Drive Kohler, WI 53044 United States Manufacturer: Shanghai Kohler Electronics., Ltd. Address of Manufacturer: No. 1955, Fengxiang Road, Baoshan Area, Shanghai, PRC Post code: 200444 Factory: Shanghai Kohler Electronics., Ltd. Address of Factory: No. 1955, Fengxiang Road, Baoshan Area, Shanghai, PRC Post code: 200444 FCC ID: N82-KOHLER030 IC: 4554A- KOHLER030 Equipment Under Test (EUT): EUT Name: Remote Controller Model No.: 1340047 Standard(s) : 47 CFR Part 15, Subpart C 15.249 RSS-210 Issue 9 August 2016 (Amendment) RSS-Gen Issue 5, May 2018 Date of Receipt: 2018-04-10 Date of Test: 2018-04-11 to 2018-04-23 Date of Issue: 2018-05-03 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Parlam Zhan E&E Section Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 2 of 29 Revision Record Version Description Date Remark 00 Original 2018-05-03 / Authorized for issue by: Eddy Zong / Project Engineer Parlam Zhan /Reviewer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 3 of 29 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result RSS-210 Issue 9 RSS-Gen Section Antenna Requirement August 2016 N/A Pass 8.3 (Amendment) Radio Spectrum Matter Part Item Standard Method Requirement Result 47 CFR Part 15, ANSI C63.10 (2013) 47 CFR Part 15, 20dB Bandwidth Pass Subpart C 15.249 Section 6.9 Subpart C 15.215 RSS-210 Issue 9 RSS-Gen Issue 5 RSS-Gen Issue 5 99% Bandwidth August 2016 Pass Section 6.6 Section 6.6 (Amendment) RSS-210 Issue 9 Field Strength of the ANSI C63.10 (2013) August 2016 RSS-210 A2.9 (a) Pass Fundamental Signal Section 6.5&6.6 (Amendment) Restricted Band RSS-210 Issue 9 ANSI C63.10 (2013) RSS-Gen Issue 5 Around Fundamental August 2016 Pass Section 6.4&6.5&6.6 Section 8.9 & 8.10 Frequency (Amendment) RSS-210 Issue 9 RSS-Gen Issue 5 ANSI C63.10 (2013) Radiated Emissions August 2016 Section 8.9 & Pass Section 6.4&6.5&6.6 (Amendment) RSS-210 A2.9 (b) This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 4 of 29 3 Contents Page 1 COVER PAGE ............................................................................................................................................. 1 2 TEST SUMMARY ......................................................................................................................................... 3 3 CONTENTS .................................................................................................................................................. 4 4 GENERAL INFORMATION ......................................................................................................................... 5 4.1 DETAILS OF E.U.T. ................................................................................................................................ 5 4.2 DESCRIPTION OF SUPPORT UNITS........................................................................................................... 5 4.3 MEASUREMENT UNCERTAINTY ................................................................................................................ 5 4.4 TEST LOCATION ..................................................................................................................................... 6 4.5 TEST FACILITY ....................................................................................................................................... 6 4.6 DEVIATION FROM STANDARDS ................................................................................................................ 6 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................... 6 5 EQUIPMENT LIST ....................................................................................................................................... 7 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ................................................................................... 8 6.1 ANTENNA REQUIREMENT ........................................................................................................................ 8 6.1.1 Test Requirement: ........................................................................................................................... 8 6.1.2 Conclusion ....................................................................................................................................... 9 7 RADIO SPECTRUM MATTER TEST RESULTS ......................................................................................10 7.1 20DB BANDWIDTH................................................................................................................................10 7.1.1 E.U.T. Operation ...........................................................................................................................10 7.1.2 Measurement Procedure and Data ..............................................................................................10 7.2 99% BANDWIDTH .................................................................................................................................13 7.2.1 E.U.T. Operation ...........................................................................................................................13 7.2.2 Test Setup Diagram ......................................................................................................................13 7.2.3 Measurement Procedure and Data ..............................................................................................13 7.3 FIELD STRENGTH OF THE FUNDAMENTAL SIGNAL ...................................................................................16 7.3.1 E.U.T. Operation ...........................................................................................................................16 7.3.2 Test Setup Diagram ......................................................................................................................16 7.3.3 Measurement Procedure and Data ..............................................................................................17 7.4 RESTRICTED BAND AROUND FUNDAMENTAL FREQUENCY ......................................................................18 7.4.1 E.U.T. Operation ...........................................................................................................................19 7.4.2 Test Setup Diagram ......................................................................................................................19 7.4.3 Measurement Procedure and Data ..............................................................................................19 7.5 RADIATED EMISSIONS ..........................................................................................................................24 7.5.1 E.U.T. Operation ...........................................................................................................................24 7.5.2 Test Setup Diagram ......................................................................................................................25 7.5.3 Measurement Procedure and Data ..............................................................................................25 8 TEST SETUP PHOTOGRAPHS ................................................................................................................29 9 EUT CONSTRUCTIONAL DETAILS .........................................................................................................29 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 5 of 29 4 General Information 4.1 Details of E.U.T. Power supply: DC 6V by 4*1.5V AA battery Operation Frequency 2415.5MHz to 2449.5MHz Modulation Type MSK Antenna Type Integral Antenna Gain 2.88dBi 4.2 Description of Support Units The EUT has been tested as an independent unit. 4.3 Measurement Uncertainty No. Item Measurement Uncertainty 1 Radio Frequency 7.25 x 10-8 2 Timeout 2s 3 Duty cycle 0.37% 4 Occupied Bandwidth 3% 5 RF conducted power 0.75dB 6 RF power density 2.84dB 7 Conducted Spurious emissions 0.75dB 4.5dB (Below 1GHz) 8 RF Radiated power 4.8dB (Above 1GHz) 4.2dB (Below 30MHz) 4.4dB (30MHz-1GHz) 9 Radiated Spurious emission test 4.6dB (1GHz-18GHz) 5.2dB (Above 18GHz) 10 Temperature test 1°C 11 Humidity test 3% 12 Supply voltages 1.5% 13 Time 3% Note: The measurement uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 6 of 29 4.4 Test Location All tests were performed at: SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. E&E Lab 588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China Tel: +86 21 6191 5666 Fax: +86 21 6191 5678 No tests were sub-contracted. 4.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L0599) CNAS has accredited SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • NVLAP (Certificate No. 201034-0) SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. is accredited by the National Voluntary Laboratory Accreditation Program(NVLAP). Certificate No. 201034-0. • FCC –Designation Number: CN5033 SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been recognized as an accredited testing laboratory. Designation Number: CN5033. Test Firm Registration Number: 479755. • Industry Canada (IC) – IC Assigned Code: 8617A The 3m Semi-anechoic chamber of SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 8617A-1. • VCCI (Member No.: 3061) The 3m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: R-3868,C-4336,T-12221,G-10830 respectively. 4.6 Deviation from Standards None 4.7 Abnormalities from Standard Conditions None This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 7 of 29 5 Equipment List Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Conducted Test Spectrum Analyzer R&S FSP-30 SHEM002-1 2017-12-20 2018-12-19 Spectrum Analyzer Agilent N9020A SHEM181-1 2017-09-26 2018-09-25 Power meter R&S NRP SHEM057-1 2017-12-26 2018-12-25 Power Sensor R&S NRP-Z22 SHEM136-1 2017-07-22 2018-07-21 Power Sensor R&S NRP-Z91 SHEM057-2 2017-12-26 2018-12-25 Signal Generator R&S SMR40 SHEM058-1 2017-07-03 2018-07-02 Signal Generator Agilent N5182A SHEM182-1 2017-09-26 2018-09-25 Communication Tester R&S CMW270 SHEM183-1 2017-10-22 2018-10-21 Switcher Tonscend JS0806 SHEM184-1 2017-09-26 2018-09-25 Splitter Anritsu MA1612A SHEM185-1 / / Coupler e-meca 803-S-1 SHEM186-1 / / High-low Temp Cabinet Suzhou Zhihe TL-40 SHEM087-1 2017-09-26 2018-09-25 AC Power Stabilizer WOCEN 6100 SHEM045-1 2017-12-26 2018-12-25 DC Power Supply QJE QJ30003SII SHEM046-1 2017-12-26 2018-12-25 Conducted test Cable / RF01, RF 02 / 2017-12-26 2018-12-25 Radiated Test EMI test receiver R&S ESU40 SHEM051-1 2017-12-20 2018-12-19 Spectrum Analyzer R&S FSP-30 SHEM002-1 2017-12-20 2018-12-19 Loop Antenna (9kHz-30MHz) Schwarzbeck FMZB1519 SHEM135-1 2017-04-10 2020-04-09 Antenna (25MHz-2GHz) Schwarzbeck VULB9168 SHEM048-1 2017-02-28 2020-02-27 Antenna (25MHz-3GHz) Schwarzbeck HL562 SHEM010-1 2017-02-28 2020-02-27 Horn Antenna (1-8GHz) Schwarzbeck HF906 SHEM009-1 2017-10-24 2020-10-23 Horn Antenna (1-18GHz) Schwarzbeck BBHA9120D SHEM050-1 2017-01-14 2020-01-13 Horn Antenna (14-40GHz) Schwarzbeck BBHA 9170 SHEM049-1 2017-12-03 2020-12-02 Pre-amplifier (9KHz-2GHz) CLAVIIO BDLNA-0001-412010 SHEM164-1 2017-08-22 2018-08-21 Pre-amplifier (1-18GHz) CLAVIIO BDLNA-0118-352810 SHEM050-2 2017-08-22 2018-08-21 High-amplifier (14-40GHz) Schwarzbeck 10001 SHEM049-2 2017-12-20 2018-12-19 Band filter LORCH 9BRX-875/X150-SR SHEM156-1 / / Band filter LORCH 13BRX-1950/X500-SR SHEM083-2 / / Band filter LORCH 5BRX-2400/X200-SR SHEM155-1 / / Band filter LORCH 5BRX-5500/X1000-SR SHEM157-2 / / High pass Filter Wainwright WHK3.0/18G-100SS SHEM157-1 / / High pass Filter Wainwright WHKS1700-3SS SHEM157-3 / / Semi/Fully Anechoic ST 11*6*6M SHEM078-2 2017-07-22 2020-07-21 RE test Cable / RE01, RE02, RE06 / 2017-12-26 2018-12-25 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 8 of 29 6 Radio Spectrum Technical Requirement 6.1 Antenna Requirement 6.1.1 Test Requirement: RSS-Gen Section 8.3 Limit: The applicant for equipment certification, as per RSP-100, must provide a list of all antenna types that may be used with the licence-exempt transmitter, indicating the maximum permissible antenna gain (in dBi) and the required impedance for each antenna. Licence-exempt transmitters that have received equipment certification may operate with different types of antennas. However, it is not permissible to exceed the maximum equivalent isotropically radiated power (e.i.r.p.) limits specified in the applicable standard (RSS) for the licence-exempt apparatus. Testing shall be performed using the highest gain antenna of each combination of licence-exempt transmitter and antenna type, with the transmitter output power set at the maximum level.9 When a measurement at the antenna connector is used to determine RF output power, the effective gain of the device’s antenna shall be stated, based on a measurement or on data from the antenna manufacturer. User manuals for transmitters equipped with detachable antennas shall also contain the following notice in a conspicuous location: This radio transmitter (identify the device by certification number) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Immediately following the above notice, the manufacturer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permissible antenna gain (in dBi). This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 9 of 29 6.1.2 Conclusion Standard Requirement: Testing shall be performed using the highest gain antenna of each combination of licence-exempt transmitter and antenna type, with the transmitter output power set at the maximum level. When a measurement at the antenna connector is used to determine RF output power, the effective gain of the device’s antenna shall be stated, based on a measurement or on data from the antenna manufacturer. EUT Antenna: The antenna is Integral and no consideration of replacement. The best case gain of the antenna is 2.88dBi. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 10 of 29 7 Radio Spectrum Matter Test Results 7.1 20dB Bandwidth Test Requirement 47 CFR Part 15, Subpart C 15.215 Test Method: ANSI C63.10 (2013) Section 6.9 Limit: N/A 7.1.1 E.U.T. Operation Operating Environment: Temperature: 21 C Humidity: 45 % RH Atmospheric Pressure: 1010 mbar Test mode a:TX mode_Keep the EUT in transmitting with modulation mode. 7.1.2 Measurement Procedure and Data CH Frequency (MHz) Bandwidth (kHz) Result Low 2414.5 798 PASS Mid 2434.5 798 PASS High 2449.5 798 PASS This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 11 of 29 Test plot as follows: Channel: Lowest * RBW 30 kHz Delta 3 [T1 ] * VBW 100 kHz 1.15 dB Ref 100 dBµV * Att 10 dB SWT 5 ms 798.000000000 kHz 100 Marker 1 [T1 ] 50.28 dBµV 2.414062000 GHz A 90 Marker 2 [T1 ] 1 PK 72.36 dBµV MAXH 80 2.414524000 GHz 2 70 60 1 3 D1 52.36 dBµV 50 40 30 20 10 0 Center 2.4145 GHz 300 kHz/ Span 3 MHz Date: 19.APR.2018 14:06:25 Channel: Middle * RBW 30 kHz Delta 3 [T1 ] * VBW 100 kHz 0.27 dB Ref 100 dBµV * Att 10 dB SWT 5 ms 798.000000000 kHz 100 Marker 1 [T1 ] 52.53 dBµV 2.434056000 GHz A 90 Marker 2 [T1 ] 1 PK 74.43 dBµV MAXH 80 2.434524000 GHz 2 70 60 1 3 D1 54.43 dBµV 50 40 30 20 10 0 Center 2.4345 GHz 300 kHz/ Span 3 MHz Date: 19.APR.2018 14:08:32 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 12 of 29 Channel: Highest * RBW 30 kHz Delta 3 [T1 ] * VBW 100 kHz -0.89 dB Ref 100 dBµV * Att 10 dB SWT 5 ms 798.000000000 kHz 100 Marker 1 [T1 ] 55.32 dBµV 2.449056000 GHz A 90 Marker 2 [T1 ] 1 PK 76.25 dBµV MAXH 80 2 2.449512000 GHz 70 60 1 3 D1 56.25 dBµV 50 40 30 20 10 0 Center 2.4495 GHz 300 kHz/ Span 3 MHz Date: 19.APR.2018 14:11:58 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 13 of 29 7.2 99% Bandwidth Test Requirement RSS-Gen Section 6.6 Test Method: RSS-Gen Section 6.6 Limit: N/A 7.2.1 E.U.T. Operation Operating Environment: Temperature: 21 C Humidity: 45 % RH Atmospheric Pressure: 1010 mbar Test mode a:TX mode_Keep the EUT in transmitting with modulation mode. 7.2.2 Test Setup Diagram 7.2.3 Measurement Procedure and Data CH Frequency (MHz) Bandwidth (MHz) Low 2414.5 0.798 Mid 2434.5 0.788 High 2449.5 0.786 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 14 of 29 Test plot as follows: Channel: lowest * RBW 30 kHz Marker 1 [T1 ] * VBW 100 kHz 72.04 dBµV Ref 100 dBµV * Att 10 dB SWT 5 ms 2.414530000 GHz 100 OBW798.000000000 kHz Temp 1 [T1 OBW] 51.01 dBµV A 90 2.414068000 GHz 1 PK Temp 2 [T1 OBW] MAXH 80 50.62 dBµV 1 2.414866000 GHz 70 60 T1 T2 50 40 30 20 10 0 Center 2.4145 GHz 300 kHz/ Span 3 MHz Channel: Middle Date: 19.APR.2018 14:18:48 * RBW 30 kHz Marker 1 [T1 ] * VBW 100 kHz 74.46 dBµV Ref 100 dBµV * Att 10 dB SWT 5 ms 2.434512000 GHz 100 OBW786.000000000 kHz Temp 1 [T1 OBW] 55.19 dBµV A 90 2.434068000 GHz 1 PK Temp 2 [T1 OBW] MAXH 80 52.81 dBµV 1 2.434854000 GHz 70 60 T1 T2 50 40 30 20 10 0 Center 2.4345 GHz 300 kHz/ Span 3 MHz Date: 19.APR.2018 14:16:24 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 15 of 29 Channel: Highest * RBW 30 kHz Marker 1 [T1 ] * VBW 100 kHz 76.10 dBµV Ref 100 dBµV * Att 10 dB SWT 5 ms 2.449506000 GHz 100 OBW786.000000000 kHz Temp 1 [T1 OBW] 58.09 dBµV A 90 2.449068000 GHz 1 PK Temp 2 [T1 OBW] MAXH 80 1 54.08 dBµV 2.449854000 GHz 70 T1 60 T2 50 40 30 20 10 0 Center 2.4495 GHz 300 kHz/ Span 3 MHz Date: 19.APR.2018 14:14:41 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 16 of 29 7.3 Field Strength of the Fundamental Signal Test Requirement RSS-210 A2.9 (a) Test Method: ANSI C63.10 (2013) Section 6.5&6.6 Limit: Fundamental Field strength of Field strength of frequency(MHz) fundamental(microvolts/meter) harmonics(microvolts/meter) 902-928 50 500 2400-2483.5 50 500 5725-5875 50 500 24000-24250 250 2500 Remark: The frequencies above 1000MHz are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. 7.3.1 E.U.T. Operation Operating Environment: Temperature: 21 C Humidity: 45 % RH Atmospheric Pressure: 1010 mbar Test mode a:TX mode_Keep the EUT in transmitting with modulation mode. 7.3.2 Test Setup Diagram This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 17 of 29 7.3.3 Measurement Procedure and Data a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 or 10 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter fully-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. c. The EUT was set 3 or 10 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. h. Test the EUT in the lowest channel, the middle channel, the Highest channel. i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode, and found the X axis positioning which it is the worst case. j. Repeat above procedures until all frequencies measured was complete. Remark: Level= Read Level+ Cable Loss+ Antenna Factor- Preamp Factor Peak value: Read Level Factor Level Limit Line Over Limit Channel Polarization (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dB) 92.78 -3.93 88.85 94 -5.15 Horizontal Lowest 79.14 -3.94 75.2 94 -18.8 Vertical 88.15 -3.96 84.19 94 -9.81 Horizontal Middle 79.39 -3.96 75.43 94 -18.57 Vertical 87.41 -3.97 83.44 94 -10.56 Horizontal Highest 76.17 -3.97 72.2 94 -21.8 Vertical Remark: 1) The basic equation with a sample calculation is as follows: Level = Read Level + Factor. (The Factor is calculated by adding the Antenna Factor, Cable Loss and Preamp Factor) 2) If the Peak value below the AV Limit, the AV test doesn’t perform for this submission. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 18 of 29 7.4 Restricted Band Around Fundamental Frequency Test Requirement RSS-Gen Section 8.9 & 8.10 Test Method: ANSI C63.10 (2013) Section 6.4&6.5&6.6 Limit: Frequency Limit (dBuV/m @3m) Remark 30MHz-88MHz 40.0 Quasi-peak Value 88MHz-216MHz 43.5 Quasi-peak Value 216MHz-960MHz 46.0 Quasi-peak Value 960MHz-1GHz 54.0 Quasi-peak Value Above 1GHz 54.0 Average Value Above 1GHz 74.0 Peak Value Emission radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209,whichever is the lesser attenuation. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 19 of 29 7.4.1 E.U.T. Operation Operating Environment: Temperature: 21 C Humidity: 45 % RH Atmospheric Pressure: 1010 mbar Test mode a:TX mode_Keep the EUT in transmitting with modulation mode. 7.4.2 Test Setup Diagram 7.4.3 Measurement Procedure and Data a. For below 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 or 10 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. For above 1GHz, the EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter fully-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. c. The EUT was set 3 or 10 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. f. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. h. Test the EUT in the lowest channel, the middle channel, the Highest channel. i. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode, and found the X axis positioning which it is the worst case. j. Repeat above procedures until all frequencies measured was complete. Remark: Level= Read Level+ Cable Loss+ Antenna Factor- Preamp Factor This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 20 of 29 Channel: lowest Horizontal: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 21 of 29 Vertical: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 22 of 29 Channel: Highest Horizontal: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 23 of 29 Vertical: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 24 of 29 7.5 Radiated Emissions Test Requirement RSS-Gen Section 8.9 & RSS-210 A2.9 (b) Test Method: ANSI C63.10 (2013) Section 6.4&6.5&6.6 Limit: Field strength Limit Measurement Distance Frequency(MHz) Detector (microvolts/meter) (dBuV/m) (meters) 0.009-0.490 2400/F(kHz) - - 300 0.490-1.705 24000/F(kHz) - - 30 1.705-30 30 - - 30 30-88 100 40.0 QP 3 88-216 150 43.5 QP 3 216-960 200 46.0 QP 3 960-1000 500 54.0 QP 3 Above 1000 500 54.0 AV 3 7.5.1 E.U.T. Operation Operating Environment: Temperature: 21 C Humidity: 45 % RH Atmospheric Pressure: 1010 mbar Test mode a:TX mode_Keep the EUT in transmitting with modulation mode. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 25 of 29 7.5.2 Test Setup Diagram 7.5.3 Measurement Procedure and Data For testing performed with the loop antenna, the center of the loop was positioned 1 m above the ground and positioned with its plane vertical at the specified distance from the EUT. During testing the loop was rotated about its vertical axis for maximum response at each azimuth and also investigated with the loop positioned in the horizontal plane. Only the worst position of vertical was shown in the report. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 26 of 29 30MHz-1GHz: Mode:a; Polarization:Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 27 of 29 Mode:a; Polarization:Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 28 of 29 Above 1GHz: Channel: lowest Frequency Reading Factor Emission Limit Over Limit Mark Detector Polarization (MHz) (dBuV) (dB) (dBuV/m) (dBuV/m) (dB) 1 4829 41.43 6.45 47.88 54 -6.12 peak Horizontal 2 7243.5 37.6 10.79 48.39 54 -5.61 peak Horizontal 3 9658 34.46 14.35 48.81 54 -5.19 peak Horizontal 4 4829 44.08 6.45 50.53 54 -3.47 peak Vertical 5 7243.5 39.08 10.79 49.87 54 -4.13 peak Vertical 6 9658 36.34 14.35 50.69 54 -3.31 peak Vertical Channel: Middle Frequency Reading Factor Emission Limit Over Limit Mark Detector Polarization (MHz) (dBuV) (dB) (dBuV/m) (dBuV/m) (dB) 1 4869 43.06 6.86 49.92 54 -4.08 peak Horizontal 2 7303.5 38.3 11.06 49.36 54 -4.64 peak Horizontal 3 9738 33.78 14.36 48.14 54 -5.86 peak Horizontal 4 4869 40.59 6.86 47.45 54 -6.55 peak Vertical 5 7303.5 37.89 11.06 48.95 54 -5.05 peak Vertical 6 9738 36.55 14.36 50.91 54 -3.09 peak Vertical Channel: Highest Frequency Reading Factor Emission Limit Over Limit Mark Detector Polarization (MHz) (dBuV) (dB) (dBuV/m) (dBuV/m) (dB) 1 4899 41.81 7.19 49 54 -5 peak Horizontal 2 7348.5 39.97 11.25 51.22 54 -2.78 peak Horizontal 3 9798 34.64 14.37 49.01 54 -4.99 peak Horizontal 4 4899 43.43 7.19 50.62 54 -3.38 peak Vertical 5 7348.5 37.15 11.25 48.4 54 -5.6 peak Vertical 6 9798 35.87 14.37 50.24 54 -3.76 peak Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180400259201 Page: 29 of 29 8 Test Setup Photographs Refer to the < Test Setup photos-FCC>. 9 EUT Constructional Details Refer to the < External Photos > & < Internal Photos >. - End of the Report - This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.


Document Created: 2018-06-14 11:42:34
Document Modified: 2018-06-14 11:42:34
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC