FG7D0540B_R01_Part 22 24 27_Sierra_WP7702PART1a-lte

FCC ID: N7NWP77B

Test Report

Download: PDF
FCCID_3856047

FCC RF Test Report Report No. : FG7D0540B FCC LTE M1 Test Report CUSTOMER : Sierra Wireless Inc. EQUIPMENT : Radio Module MODEL NAME : WP7702 FCC ID : N7NWP77B STANDARD : 47 CFR Part 2, 22(H), 24(E), 27 CLASSIFICATION : PCS Licensed Transmitter (PCB) This is a partial report. The product was received on Dec. 05, 2017 and completely tested on Jan. 11, 2018. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample has been evaluated in accordance with the test procedures given in ANSI / TIA-603-E and the testing has shown the tested sample to be in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Joseph Lin / Supervisor Approved by: Jones Tsai / Manager SPORTON INTERNATIONAL INC. st No. 52, Hwa Ya 1 Rd., Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan, R.O.C. SPORTON INTERNATIONAL INC. Page Number : 1 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B TABLE OF CONTENTS REVISION HISTORY.......................................................................................................................................... 3 SUMMARY OF TEST RESULT ......................................................................................................................... 4 1 GENERAL DESCRIPTION .......................................................................................................................... 5 1.1 Customer ........................................................................................................................................... 5 1.2 Manufacturer ...................................................................................................................................... 5 1.3 Product Feature of Equipment Under Test ........................................................................................ 5 1.4 Product Specification of Equipment Under Test ................................................................................ 5 1.5 Modification of EUT ........................................................................................................................... 5 1.6 Testing Location ................................................................................................................................ 6 1.7 Applicable Standards ......................................................................................................................... 6 2 TEST CONFIGURATION OF EQUIPMENT UNDER TEST ........................................................................ 7 2.1 Test Mode .......................................................................................................................................... 7 2.2 Connection Diagram of Test System ................................................................................................. 8 2.3 Support Unit used in test configuration and system .......................................................................... 9 2.4 Measurement Results Explanation Example ..................................................................................... 9 2.5 Frequency List of Low/Middle/High Channels ................................................................................. 10 3 CONDUCTED TEST ITEMS ...................................................................................................................... 12 3.1 Measuring Instruments .................................................................................................................... 12 3.2 Test Setup ....................................................................................................................................... 12 3.3 Conducted Output Power ................................................................................................................ 13 3.4 Peak-to-Average Ratio .................................................................................................................... 14 3.5 Occupied Bandwidth ........................................................................................................................ 15 3.6 Conducted Band Edge .................................................................................................................... 16 3.7 Conducted Spurious Emission ........................................................................................................ 18 3.8 Frequency Stability .......................................................................................................................... 19 4 RADIATED TEST ITEMS .......................................................................................................................... 20 4.1 Measuring Instruments .................................................................................................................... 20 4.2 Test Setup ....................................................................................................................................... 20 4.3 Test Result of Radiated Test ........................................................................................................... 20 4.4 Radiated Spurious Emission ........................................................................................................... 21 5 LIST OF MEASURING EQUIPMENT ........................................................................................................ 22 6 UNCERTAINTY OF EVALUATION ........................................................................................................... 23 APPENDIX A. TEST RESULTS OF CONDUCTED TEST APPENDIX B. TEST RESULTS OF RADIATED TEST SPORTON INTERNATIONAL INC. Page Number : 2 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DATE FG7D0540B Rev. 01 Initial issue of report Apr. 24, 2018 SPORTON INTERNATIONAL INC. Page Number : 3 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B SUMMARY OF TEST RESULT Report FCC Rule Description Limit Result Remark Section 3.3 §2.1046 Conducted Output Power Reporting Only PASS - 3.4 §24.232(d) Peak-to-Average Ratio <13 dB PASS - 3.5 §2.1049 Occupied Bandwidth Reporting Only PASS - §2.1051 §22.917(a) Conducted Band Edge Measurement §24.238(a) 3.6 (Band 2) (Band 4) (Band 12) < 43+10log10(P[Watts]) PASS - §27.53(c)(2)(4) (Band 13) (Band 26) §27.53(g) §27.53(h) §2.1051 §22.917(a) Conducted Spurious Emission §24.238(a) 3.7 (Band 2) (Band 4) (Band 12) < 43+10log10(P[Watts]) PASS - §27.53(c)(2) (Band 13) (Band 26) §27.53(g) §27.53(h) §2.1055 < 2.5 ppm for Part 22 §22.355 Frequency Stability 3.8 §2.1055 PASS - Temperature & Voltage §24.235 Within Authorized Band §27.54 §2.1053 §22.917(a) §24.238(a) Radiated Spurious Emission Under limit 4.4 §27.53(c)(2) (Band 2) (Band 4) (Band 12) < 43+10log10(P[Watts]) PASS 6.91 dB at §27.53(f) (Band 13) (Band 26) 1568.000 MHz §27.53(g) §27.53(h) SPORTON INTERNATIONAL INC. Page Number : 4 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 1 General Description 1.1 Customer Sierra Wireless Inc. 13811 Wireless Way Richmond, BC Canada V6V 3A4 1.2 Manufacturer Sierra Wireless Inc. 13811 Wireless Way Richmond, BC Canada V6V 3A4 1.3 Product Feature of Equipment Under Test WP7702 is an IOT module supporting multiband LTE CATM1/NB1 and 2G operation. 1.4 Product Specification of Equipment Under Test Standards-related Product Specification LTE Band 2 : 1850.7 MHz ~ 1909.3 MHz LTE Band 4 : 1710.7 MHz ~ 1754.3 MHz Tx Frequency LTE Band 12 : 699.7 MHz ~ 715.3 MHz LTE Band 13 : 779.5 MHz ~ 784.5 MHz LTE Band 26 : 824.7MHz ~ 848.3 MHz LTE Band 2 : 1930.7 MHz ~ 1989.3 MHz LTE Band 4 : 2110.7 MHz ~ 2154.3 MHz Rx Frequency LTE Band 12 : 729.7 MHz ~ 745.3 MHz LTE Band 13 : 748.5 MHz ~ 753.5 MHz LTE Band 26 : 869.7MHz ~ 893.3MHz LTE Band 2 : 1.4MHz / 3MHz / 5MHz / 10MHz / 15MHz / 20MHz LTE Band 4 : 1.4MHz / 3MHz / 5MHz / 10MHz / 15MHz / 20MHz Bandwidth LTE Band 12 : 1.4MHz / 3MHz / 5MHz / 10MHz LTE Band 13 : 5MHz / 10MHz LTE Band 26 : 1.4MHz / 3MHz / 5MHz / 10MHz / 15MHz LTE Band 2 : 23.27 dBm LTE Band 4 : 23.40 dBm Maximum Output Power to LTE Band 12 : 23.25 dBm Antenna LTE Band 13 : 23.54 dBm LTE Band 26 : 23.83 dBm Type of Modulation QPSK / 16QAM 1.5 Modification of EUT No modifications are made to the EUT during all test items. SPORTON INTERNATIONAL INC. Page Number : 5 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 1.6 Testing Location Sporton Lab is accredited to ISO 17025 by Taiwan Accreditation Foundation (TAF code : 1190) and the FCC designation No. TW1190 and TW0007 under the FCC 2.948(e) by Mutual Recognition Agreement (MRA) in FCC Test. Test Site SPORTON INTERNATIONAL INC. st No. 52, Hwa Ya 1 Rd., Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan, R.O.C. Test Site Location TEL: +886-3-327-3456 FAX: +886-3-328-4978 Sporton Site No. Test Site No. TH05-HY Test Site SPORTON INTERNATIONAL INC. No.58, Aly. 75, Ln. 564, Wenhua 3rd Rd. Guishan Dist, Taoyuan City, Taiwan (R.O.C.) Test Site Location TEL: +886-3-327-0868 FAX: +886-3-327-0855 Sporton Site No. Test Site No. 03CH11-HY 1.7 Applicable Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards:  47 CFR Part 2, 22(H), 24(E), 27  ANSI / TIA-603-E  FCC KDB 971168 D01 Power Meas. License Digital Systems v03r01 Remark: All test items were verified and recorded according to the standards and without any deviation during the test. SPORTON INTERNATIONAL INC. Page Number : 6 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 2 Test Configuration of Equipment Under Test 2.1 Test Mode Antenna port conducted and radiated test items listed below are performed according to KDB 971168 D01 Power Meas. License Digital Systems v03r01 with maximum output power. Radiated measurements are performed by rotating the EUT in three different orthogonal test planes to find the maximum emission. Bandwidth (MHz) Modulation RB # Test Channel Test Items Band 1.4 3 5 10 15 20 QPSK 16QAM 1 Half Full L M H 2 v v v v v v v v v v v v v v 4 v v v v v v v v v v v v v v Max. Output v v v 12 v - - v v v v v v v v Power 13 - - v v - - v v v v v v v v 26 v v v v v - v v v v v v v v 2 v v v v v v v v 4 v v v v v v v v Peak-to-Aver 12 v - - v v v v v v v age Ratio 13 - - v - - v v v v v v v 26 v - v v v v v v v 2 v v v v v v v 4 v v v v v v v 26dB and 99% 12 v - - v v v v v v Bandwidth - - 13 - - v v v v v v v 26 v - v v v v v v 2 v v v v v v v 4 v v v v v v v Conducted 12 v - - v v v v v v Band Edge 13 - - v - - v v v v v v 26 v - v v v v v v 2 v v v v v v v 4 v v v v v v v Conducted Spurious 12 v - - v v v v v v Emission 13 - - v - - v v v v v v 26 v - v v v v v v SPORTON INTERNATIONAL INC. Page Number : 7 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B Bandwidth (MHz) Modulation RB # Test Channel Test Items Band 1.4 3 5 10 15 20 QPSK 16QAM 1 Half Full L M H 2 v v v v 4 v v v v Frequency 12 v - - v v v Stability 13 - - v - - v v v 26 v - v v v 2 Worst Case v v v 4 Worst Case v v v Radiated Spurious 12 Worst Case v v v Emission 13 Worst Case v v v 26 Worst Case v v v 1. The mark “v “ means that this configuration is chosen for testing 2. The mark “-“ means that this bandwidth is not supported. Note 3. The device is investigated from 30MHz to 10 times of fundamental signal for radiated spurious emission test under different RB size/offset and modulations in exploratory test. Subsequently, only the worst case emissions are reported. 2.2 Connection Diagram of Test System SPORTON INTERNATIONAL INC. Page Number : 8 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 2.3 Support Unit used in test configuration and system Item Equipment Trade Name Model No. FCC ID Data Cable Power Cord 1. LTE Base Station Anritsu MT8821C N/A N/A Unshielded, 1.8 m 2.4 Measurement Results Explanation Example For all conducted test items: The offset level is set in the spectrum analyzer to compensate the RF cable loss and attenuator factor between EUT conducted output port and spectrum analyzer. With the offset compensation, the spectrum analyzer reading level is exactly the EUT RF output level. The spectrum analyzer offset is derived from RF cable loss and attenuator factor. Offset = RF cable loss + attenuator factor. Following shows an offset computation example with cable loss 4.2 dB and 10dB attenuator. Example : Offset(dB) = RF cable loss(dB) + attenuator factor(dB). = 4.2 + 10 = 14.2 (dB) SPORTON INTERNATIONAL INC. Page Number : 9 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 2.5 Frequency List of Low/Middle/High Channels LTE Band 2 Channel and Frequency List BW [MHz] Channel/Frequency(MHz) Lowest Middle Highest Channel 18700 18900 19100 20 Frequency 1860.0 1880.0 1900.0 Channel 18675 18900 19125 15 Frequency 1857.5 1880.0 1902.5 Channel 18650 18900 19150 10 Frequency 1855.0 1880.0 1905.0 Channel 18625 18900 19175 5 Frequency 1852.5 1880.0 1907.5 Channel 18615 18900 19185 3 Frequency 1851.5 1880.0 1908.5 Channel 18607 18900 19193 1.4 Frequency 1850.7 1880.0 1909.3 LTE Band 4 Channel and Frequency List BW [MHz] Channel/Frequency(MHz) Lowest Middle Highest Channel 20050 20175 20300 20 Frequency 1720.0 1732.5 1745.0 Channel 20025 20175 20325 15 Frequency 1717.5 1732.5 1747.5 Channel 20000 20175 20350 10 Frequency 1715.0 1732.5 1750.0 Channel 19975 20175 20375 5 Frequency 1712.5 1732.5 1752.5 Channel 19965 20175 20385 3 Frequency 1711.5 1732.5 1753.5 Channel 19957 20175 20393 1.4 Frequency 1710.7 1732.5 1754.3 SPORTON INTERNATIONAL INC. Page Number : 10 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B LTE Band 12 Channel and Frequency List BW [MHz] Channel/Frequency(MHz) Lowest Middle Highest Channel 23060 23095 23130 10 Frequency 704.0 707.5 711.0 Channel 23035 23095 23155 5 Frequency 701.5 707.5 713.5 Channel 23025 23095 23165 3 Frequency 700.5 707.5 714.5 Channel 23017 23095 23173 1.4 Frequency 699.7 707.5 715.3 LTE Band 13 Channel and Frequency List BW [MHz] Channel/Frequency(MHz) Lowest Middle Highest Channel - 23230 - 10 Frequency - 782.0 - Channel 23205 23230 23255 5 Frequency 779.5 782.0 784.5 LTE Band 26 Channel and Frequency List BW [MHz] Channel/Frequency(MHz) Lowest Middle Highest Channel 26865 26915 26965 15 Frequency 831.5 836.5 841.5 Channel 26840 26915 26990 10 Frequency 829.0 836.5 844.0 Channel 26815 26915 27015 5 Frequency 826.5 836.5 846.5 Channel 26805 26915 27025 3 Frequency 825.5 836.5 847.5 Channel 26797 26915 27033 1.4 Frequency 824.7 836.5 848.3 SPORTON INTERNATIONAL INC. Page Number : 11 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 3 Conducted Test Items 3.1 Measuring Instruments See list of measuring instruments of this test report. 3.2 Test Setup 3.2.1 Conducted Output Power 3.2.2 Peak-to-Average Ratio, Occupied Bandwidth ,Conducted Band-Edge and Conducted Spurious Emission 3.2.3 Frequency Stability 3.2.4 Test Result of Conducted Test Please refer to Appendix A. SPORTON INTERNATIONAL INC. Page Number : 12 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 3.3 Conducted Output Power 3.3.1 Description of the Conducted Output Power Measurement A system simulator was used to establish communication with the EUT. Its parameters were set to force the EUT transmitting at maximum output power. The measured power in the radio frequency on the transmitter output terminals shall be reported. 3.3.2 Test Procedures 1. The transmitter output port was connected to the system simulator. 2. Set EUT at maximum power through the system simulator. 3. Select lowest, middle, and highest channels for each band and different modulation. 4. Measure and record the power level from the system simulator. SPORTON INTERNATIONAL INC. Page Number : 13 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 3.4 Peak-to-Average Ratio 3.4.1 Description of the PAR Measurement Power Complementary Cumulative Distribution Function (CCDF) curves provide a means for characterizing the power peaks of a digitally modulated signal on a statistical basis. A CCDF curve depicts the probability of the peak signal amplitude exceeding the average power level. Most contemporary measurement instrumentation include the capability to produce CCDF curves for an input signal provided that the instrument’s resolution bandwidth can be set wide enough to accommodate the entire input signal bandwidth. In measuring transmissions in this band using an average power technique, the peak-to-average ratio (PAR) of the transmission may not exceed 13 dB. 3.4.2 Test Procedures 1. The testing follows FCC KDB 971168 v03r01 Section 5.7.1. 2. The EUT was connected to spectrum and system simulator via a power divider. 3. Set the CCDF (Complementary Cumulative Distribution Function) option in spectrum analyzer. 4. The highest RF powers were measured and recorded the maximum PAPR level associated with a probability of 0.1 %. 5. Record the deviation as Peak to Average Ratio. SPORTON INTERNATIONAL INC. Page Number : 14 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 3.5 Occupied Bandwidth 3.5.1 Description of Occupied Bandwidth Measurement The occupied bandwidth is the width of a frequency band such that, below the lower and above the upper frequency limits, the mean powers emitted are each equal to a specified percentage 0.5% of the total mean transmitted power. The 26 dB emission bandwidth is defined as the frequency range between two points, one above and one below the carrier frequency, at which the spectral density of the emission is attenuated 26 dB below the maximum in-band spectral density of the modulated signal. Spectral density (power per unit bandwidth) is to be measured with a detector of resolution bandwidth equal to approximately 1.0% of the emission bandwidth. 3.5.2 Test Procedures 1. The testing follows FCC KDB 971168 v03r01 Section 4.2. 2. The EUT was connected to spectrum analyzer and system simulator via a power divider. 3. The spectrum analyzer center frequency is set to the nominal EUT channel center frequency. The span range for the spectrum analyzer shall be between two and five times the anticipated OBW. 4. The nominal resolution bandwidth (RBW) shall be in the range of 1 to 5 % of the anticipated OBW, and the VBW shall be at least 3 times the RBW. 5. Set the detection mode to peak, and the trace mode to max hold. 6. Determine the reference value: Set the EUT to transmit a modulated signal. Allow the trace to stabilize. Set the spectrum analyzer marker to the highest level of the displayed trace. (this is the reference value) 7. Determine the “-26 dB down amplitude” as equal to (Reference Value – X). 8. Place two markers, one at the lowest and the other at the highest frequency of the envelope of the spectral display such that each marker is at or slightly below the “–X dB down amplitude” determined in step 6. If a marker is below this “-X dB down amplitude” value it shall be placed as close as possible to this value. The OBW is the positive frequency difference between the two markers. 9. Use the 99 % power bandwidth function of the spectrum analyzer and report the measured bandwidth. SPORTON INTERNATIONAL INC. Page Number : 15 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 3.6 Conducted Band Edge 3.6.1 Description of Conducted Band Edge Measurement 22.917(a) For operations in the 824 – 849 MHz band, the FCC limit is 43 + 10log10(P[Watts]) dB below the transmitter power P(Watts) in a 100kHz bandwidth. However, in the 1MHz bands immediately outside and adjacent to the licensee's frequency block, a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. 24.238 (a) For operations in the 1850-1910 and 1930-1990 MHz band, the FCC limit is 43 + 10log10(P[Watts]) dB below the transmitter power P(Watts) in a 1MHz bandwidth. However, in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. 27.53 (c) For operations in the 776-788 MHz band, the FCC limit is 43 + 10log10(P[Watts]) dB below the transmitter power P(Watts) in a 100 kHz bandwidth. However, in the 100 kHz bands immediately outside and adjacent to the frequency block, a resolution bandwidth of at least 30 kHz may be employed. In addition, the power of any unwanted emissions in any 6.25 kHz bandwidth for all frequencies between 763-775 MHz and 793-806 MHz shall be attenuated below the transmitter power, P (dBW), by at least 65 + 10 log10 p(watts), dB, for mobile and portable equipment. 27.53 (g) For operations in the 698 -746 MHz band, the FCC limit is 43 + 10log10(P[Watts]) dB below the transmitter power P(Watts) in a 100 kHz bandwidth. However, in the 100 kilohertz bands immediately outside and adjacent to a licensee's frequency block, a resolution bandwidth of at least 30 kHz may be employed. 27.53 (h) For operations in the 1710 – 1755 MHz band, the FCC limit is 43 + 10log10(P[Watts]) dB below the transmitter power P(Watts) in a 1 MHz bandwidth. However, in the 1MHz bands immediately outside and adjacent to the licensee's frequency block, a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. SPORTON INTERNATIONAL INC. Page Number : 16 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 3.6.2 Test Procedures 1. The testing follows FCC KDB 971168 v03r01 Section 6.0. 2. The EUT was connected to spectrum analyzer and system simulator via a power divider. 3. The band edges of low and high channels for the highest RF powers were measured. 4. Set RBW >= 1% EBW in the 1MHz band immediately outside and adjacent to the band edge. 5. Beyond the 1 MHz band from the band edge, RBW=1MHz was used. 6. Set spectrum analyzer with RMS detector. 7. The RF fundamental frequency should be excluded against the limit line in the operating frequency band. 8. Checked that all the results comply with the emission limit line. The limit line is derived from 43 + 10log(P)dB below the transmitter power P(Watts) SPORTON INTERNATIONAL INC. Page Number : 17 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 3.7 Conducted Spurious Emission 3.7.1 Description of Conducted Spurious Emission Measurement The power of any emission outside of the authorized operating frequency ranges must be lower than the transmitter power (P) by a factor of at least 43 + 10 log (P) dB. It is measured by means of a calibrated spectrum analyzer and scanned from 30 MHz up to a th frequency including its 10 harmonic. 3.7.2 Test Procedures 1. The testing follows FCC KDB 971168 v03r01 Section 6.0. 2. The EUT was connected to spectrum analyzer and system simulator via a power divider. 3. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 4. The middle channel for the highest RF power within the transmitting frequency was measured. 5. The conducted spurious emission for the whole frequency range was taken. 6. Make the measurement with the spectrum analyzer's RBW = 1MHz, VBW = 3MHz. 7. Set spectrum analyzer with RMS detector. 8. Taking the record of maximum spurious emission. 9. The RF fundamental frequency should be excluded against the limit line in the operating frequency band. 10. The limit line is derived from 43 + 10log(P)dB below the transmitter power P(Watts) SPORTON INTERNATIONAL INC. Page Number : 18 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 3.8 Frequency Stability 3.8.1 Description of Frequency Stability Measurement The frequency stability shall be measured by variation of ambient temperature and variation of primary supply voltage to ensure that the fundamental emission stays within the authorized frequency block. The frequency stability of the transmitter shall be maintained within ±0.00025% (±2.5ppm) of the center frequency. 3.8.2 Test Procedures for Temperature Variation 1. The testing follows FCC KDB 971168 v03r01 Section 9.0. 2. The EUT was set up in the thermal chamber and connected with the system simulator. 3. With power OFF, the temperature was decreased to -30°C and the EUT was stabilized before testing. Power was applied and the maximum change in frequency was recorded within one minute. 4. With power OFF, the temperature was raised in 10°C step up to 50°C. The EUT was stabilized at each step for at least half an hour. Power was applied and the maximum frequency change was recorded within one minute. 3.8.3 Test Procedures for Voltage Variation 1. The testing follows FCC KDB 971168 v03r01 Section 9.0. 2. The EUT was placed in a temperature chamber at 20±5° C and connected with the system simulator. 3. The power supply voltage to the EUT was varied from 85% to 115% of the nominal value measured at the input to the EUT. 4. The variation in frequency was measured for the worst case. SPORTON INTERNATIONAL INC. Page Number : 19 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 4 Radiated Test Items 4.1 Measuring Instruments See list of measuring instruments of this test report. 4.2 Test Setup 4.2.1 For radiated test from 30MHz to 1GHz 4.2.2 For radiated test above 1GHz 4.3 Test Result of Radiated Test Please refer to Appendix B. SPORTON INTERNATIONAL INC. Page Number : 20 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 4.4 Radiated Spurious Emission 4.4.1 Description of Radiated Spurious Emission The radiated spurious emission was measured by substitution method according to ANSI / TIA-603-E. The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitter power (P) by a factor of at least 43 + 10 log (P) dB. For LTE Band 12,13 For operations in the 746-758 MHz, 775-788 MHz, and 805-806 MHz bands, emissions in the band 1559-1610 MHz shall be limited to −70 dBW/MHz equivalent isotropically radiated power (EIRP) for wideband signals, and −80 dBW EIRP for discrete emissions of less than 700 Hz bandwidth. The spectrum is scanned from 30 MHz up to a frequency including its 10th harmonic. 4.4.2 Test Procedures 1. The testing follows FCC KDB 971168 v03r01 Section 5.8 and ANSI / TIA-603-E Section 2.2.12. 2. The EUT was placed on a turntable with 0.8 meter for frequency below 1GHz and 1.5 meter for frequency above 1GHz respectively above ground. 3. The EUT was set 3 meters from the receiving antenna, which was mounted on the antenna tower. 4. The table was rotated 360 degrees to determine the position of the highest spurious emission. 5. The height of the receiving antenna is varied between one meter and four meters to search the maximum spurious emission for both horizontal and vertical polarizations. 6. Make the measurement with the spectrum analyzer's RBW = 1MHz, VBW = 3MHz, taking the record of maximum spurious emission. 7. A horn antenna was substituted in place of the EUT and was driven by a signal generator. 8. Tune the output power of signal generator to the same emission level with EUT maximum spurious emission. 9. Taking the record of output power at antenna port. 10. Repeat step 7 to step 8 for another polarization. 11. The RF fundamental frequency should be excluded against the limit line in the operating frequency band. The limit line is derived from 43 + 10log(P)dB below the transmitter power P(Watts) SPORTON INTERNATIONAL INC. Page Number : 21 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 5 List of Measuring Equipment Calibration Instrument Manufacturer Model No. Serial No. Characteristics Test Date Due Date Remark Date Spectrum Dec. 05, 2017~ Conducted Rohde & Schwarz FSV40 101397 10Hz~40GHz Nov. 09, 2017 Nov. 08, 2018 Analyzer Jan. 11, 2018 (TH05-HY) Temperature Dec. 05, 2017~ Conducted ESPEC SH-641 92013720 -30℃~70℃ Aug. 28, 2017 Aug. 27, 2018 Chamber Jan. 11, 2018 (TH05-HY) Programmable Dec. 05, 2017~ Conducted GW Instek PSS-2005 EL890001 1V~20V 0.5A~5A Oct. 06, 2017 Oct. 05, 2018 Power Supply Jan. 11, 2018 (TH05-HY) 1-18GHz Dec. 05, 2017~ Conducted Coupler Warison #B 1G~18GHz Feb. 20, 2017 Feb. 19, 2018 20dB Jan. 11, 2018 (TH05-HY) 25WSMA CBL 35414&AT-N Dec. 19, 2017~ Radiation Bilog Antenna TESEQ 30MHz~1GHz Oct. 14, 2017 Oct. 13, 2018 Directional 6111D&N-6- 0602 Dec. 21, 2017 (03CH11-HY) Coupler BBHA 069120 Dec. 19, 2017~ Radiation Horn Antenna SCHWARZBECK 9120D-1326 1GHz ~ 18GHz Oct. 16, 2017 Oct. 15, 2018 D Dec. 21, 2017 (03CH11-HY) BBHA 9120 Dec. 19, 2017~ Radiation Horn Antenna SCHWARZBECK 9120D-1522 1GHz ~ 18GHz Mar. 17, 2017 Mar. 16, 2018 D Dec. 21, 2017 (03CH11-HY) SHF-EHF Horn BBHA91705 Dec. 19, 2017~ Radiation SCHWARZBECK BBHA 9170 18GHz- 40GHz Apr. 27, 2017 Apr. 26, 2018 Antenna 76 Dec. 21, 2017 (03CH11-HY) SHF-EHF Horn BBHA91705 Dec. 19, 2017~ Radiation SCHWARZBECK BBHA 9170 18GHz- 40GHz Nov. 27, 2017 Nov. 26, 2018 Antenna 84 Dec. 21, 2017 (03CH11-HY) Dec. 19, 2017~ Radiation Amplifier SONOMA 310N 187312 9kHz~1GHz Nov. 10, 2016 Nov. 09, 2018 Dec. 21, 2017 (03CH11-HY) AMF-7D-001 Dec. 19, 2017~ Radiation Preamplifier MITEQ 1590074 1GHz~18GHz May 22, 2017 May 21, 2018 01800-30-10 Dec. 21, 2017 (03CH11-HY) P MY5327008 Dec. 19, 2017~ Radiation Preamplifier Keysight 83017A 1GHz~26.5GHz Nov. 10, 2016 Nov. 09, 2018 0 Dec. 21, 2017 (03CH11-HY) TTA1840-35- 18GHz~40GHz,V Dec. 19, 2017~ Radiation Amplifier MITEQ 1871923 Jul. 18, 2017 Jul. 17, 2018 HG SWR : 2.5:1 max Dec. 21, 2017 (03CH11-HY) EMI Test Agilent N9038A MY5329004 Dec. 19, 2017~ Radiation 20MHz~8.4GHz Jan. 19, 2017 Jan. 18, 2018 Receiver Technologies (MXE) 5 Dec. 21, 2017 (03CH11-HY) Spectrum MY5420048 Dec. 19, 2017~ Radiation Keysight N9010A 10Hz ~ 44GHz Oct. 19, 2017 Oct. 18, 2018 Analyzer 6 Dec. 21, 2017 (03CH11-HY) AM-BS-4500 Dec. 19, 2017~ Radiation Antenna Mast EMEC N/A 1~4m N/A N/A -B Dec. 21, 2017 (03CH11-HY) Dec. 19, 2017~ Radiation Turn Table EMEC TT 2000 N/A 0~360 Degree N/A N/A Dec. 21, 2017 (03CH11-HY) WHKX12-10 Dec. 19, 2017~ Radiation Filter Wainwright SN2 1.2G High Pass Sep. 18, 2017 Sep. 17, 2018 80-1200-150 Dec. 21, 2017 (03CH11-HY) 0-60SS SPORTON INTERNATIONAL INC. Page Number : 22 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B 6 Uncertainty of Evaluation Uncertainty of Radiated Emission Measurement (30 MHz ~ 1000 MHz) Measuring Uncertainty for a Level of 3.37 Confidence of 95% (U = 2Uc(y)) Uncertainty of Radiated Emission Measurement (1 GHz ~ 18 GHz) Measuring Uncertainty for a Level of 3.67 Confidence of 95% (U = 2Uc(y)) Uncertainty of Radiated Emission Measurement (18 GHz ~ 40 GHz) Measuring Uncertainty for a Level of 4.03 Confidence of 95% (U = 2Uc(y)) SPORTON INTERNATIONAL INC. Page Number : 23 of 23 TEL : 886-3-327-3456 Report Issued Date : Apr. 24, 2018 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : N7NWP77B Report Template No.: BU5-FGLTE Version 2.0

FCC RF Test Report Report No. : FG7D0540B Appendix A. Test Results of Conducted Test Conducted Output Power(Average power) LTE Band 2 Maximum Average Power [dBm] Index BW [MHz] Mod RB Size RB Offset Lowest Middle Highest L M H 20 1 0 0 0 15 22.82 22.74 23.13 20 QPSK 1 5 0 0 15 22.78 22.69 23.18 20 6 0 0 0 15 22.54 22.51 22.74 20 1 0 0 0 15 22.65 22.29 22.96 20 16-QAM 1 5 0 0 15 22.68 22.36 22.72 20 6 0 0 0 15 22.59 22.43 23.09 15 1 0 0 0 11 22.77 22.22 22.66 15 QPSK 1 5 0 0 11 22.73 22.32 22.63 15 6 0 0 0 11 22.33 22.52 22.18 15 1 0 0 0 11 22.65 22.81 21.59 15 16-QAM 1 5 0 0 11 22.59 22.89 22.51 15 6 0 0 0 11 22.41 22.91 22.23 10 1 0 0 0 7 22.45 22.55 22.36 10 QPSK 1 5 0 0 7 22.41 22.66 22.33 10 6 0 0 0 7 21.59 21.51 21.47 10 1 0 0 0 7 23.22 22.39 22.08 10 16-QAM 1 5 0 0 7 23.09 22.33 22.01 10 6 0 0 0 7 22.11 21.36 21.19 5 1 0 0 0 3 22.95 23.24 23.13 5 QPSK 1 5 0 0 3 22.77 23.27 23.16 5 6 0 0 0 3 21.57 22.16 22.09 5 1 0 0 0 3 22.23 22.54 22.57 5 16-QAM 1 5 0 0 3 22.17 22.78 22.59 5 6 0 0 0 3 21.12 21.74 21.58 3 1 0 0 0 1 22.61 22.91 22.55 3 QPSK 1 5 0 0 1 22.73 22.95 22.59 3 6 0 0 0 1 20.61 20.73 20.41 3 1 0 0 0 1 21.76 21.19 21.02 3 16-QAM 1 5 0 0 1 21.83 21.31 20.98 3 6 0 0 0 1 19.85 19.43 19.42 1.4 1 0 0 0 0 22.67 23.09 22.68 1.4 QPSK 1 5 0 0 0 22.79 23.10 22.66 1.4 6 0 0 0 0 20.66 20.87 20.72 1.4 1 0 0 0 0 21.93 21.51 21.32 1.4 16-QAM 1 5 0 0 0 21.96 21.56 21.31 1.4 6 0 0 0 0 19.89 19.37 19.45 A1-1 of 5

FCC RF Test Report Report No. : FG7D0540B LTE Band 4 Maximum Average Power [dBm] Index BW [MHz] Mod RB Size RB Offset Lowest Middle Highest L M H 20 1 0 0 0 15 22.53 22.34 22.77 20 QPSK 1 5 0 0 15 22.61 22.29 22.71 20 6 0 0 0 15 22.57 22.51 22.68 20 1 0 0 0 15 22.29 23.40 22.24 20 16-QAM 1 5 0 0 15 22.31 23.29 22.19 20 6 0 0 0 15 22.43 23.36 22.32 15 1 0 0 0 11 21.93 22.88 22.86 15 QPSK 1 5 0 0 11 22.86 22.97 22.81 15 6 0 0 0 11 22.48 22.58 22.57 15 1 0 0 0 11 22.41 22.46 22.75 15 16-QAM 1 5 0 0 11 22.43 22.53 22.73 15 6 0 0 0 11 22.53 22.85 22.93 10 1 0 0 0 7 22.77 22.96 23.03 10 QPSK 1 5 0 0 7 22.79 22.95 23.04 10 6 0 0 0 7 21.41 21.63 21.78 10 1 0 0 0 7 22.52 22.61 22.78 10 16-QAM 1 5 0 0 7 22.56 22.68 22.81 10 6 0 0 0 7 21.17 21.31 21.51 5 1 0 0 0 3 22.97 23.13 23.27 5 QPSK 1 5 0 0 3 22.71 23.05 23.03 5 6 0 0 0 3 21.53 21.96 21.72 5 1 0 0 0 3 22.55 22.47 22.75 5 16-QAM 1 5 0 0 3 22.57 22.41 22.78 5 6 0 0 0 3 21.75 21.48 21.93 3 1 0 0 0 1 22.70 22.57 22.19 3 QPSK 1 5 0 0 1 22.69 22.58 22.32 3 6 0 0 0 1 20.51 20.58 20.53 3 1 0 0 0 1 21.04 21.11 22.44 3 16-QAM 1 5 0 0 1 21.06 21.13 22.03 3 6 0 0 0 1 19.96 20.22 20.41 1.4 1 0 0 0 0 22.47 22.38 22.22 1.4 QPSK 1 5 0 0 0 22.49 22.33 22.23 1.4 6 0 0 0 0 20.68 20.54 20.54 1.4 1 0 0 0 0 21.86 20.91 22.01 1.4 16-QAM 1 5 0 0 0 21.93 21.07 22.06 1.4 6 0 0 0 0 19.92 20.12 20.41 A1-2 of 5


Document Created: 2018-04-25 16:43:39
Document Modified: 2018-04-25 16:43:39
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC