HL6528-G2.8V Module FCC MPE Evaluation

FCC ID: N7NHL6528G28V

RF Exposure Info

Download: PDF
FCCID_2285931

MPE Evaluation for HL6528-G2.8V Wireless Module May 21, 2014

1. Introduction In this application we seek for modular approval to the HL6528-G2.8V wireless module for use in standalone and collocated simultaneous transmission under mobile configuration. This Maximum Permissive Exposure (MPE) report demonstrates compliance analysis for HL6528-G2.8V wireless module with FCC CFR 47 §2.1091 and IC RSS-102 for standalone and collocated transmission in mobile exposure conditions. The MPE analysis is limited for US / Canada bands only. The general population/uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercise control over their exposure. Any collocated transmitter must have a valid FCC ID documenting equivalent or degraded RF characteristics with the collocated parameters defined in this MPE report. A separation distance of 20cm or more shall be maintained between the end user and each WWAN, WiMAX or WLAN, and Bluetooth transmitting antenna. Portable user conditions or additional collocated transmitters not allowed based on this RF exposure analysis require a Class II permissive change and updated RF exposure report.

2. RF Exposure Limits and Equations FCC RULES: According to FCC OET Bulletin 65 Supplement C, the criteria listed in Table 1 shall be used to evaluate the environmental impact of human exposure to radio frequency (RF) radiation as specified in §1.1307. Table 1 : Limits for Maximum Permissible Exposure (MPE) IC RULES: IC has adopted the RF field strength limits established in Health Canada’s RF exposure guideline. The limits are shown in Table 2 below per RSS 102. Table 2 : RF Field Strength Limits for Devices Used by the General Public (Uncontrolled Environment)

EQUATIONS: Power density is given by : S = EIRP /(4 * Pi* D^2) where S = Power density (mW/cm^2) EIRP = Equivalent Isotropic Radiated Power (mW) D = Separation distance (cm)

3. Product Declarations The HL6528-G2.8V wireless module can be installed for use in any mobile host as long as the antenna gain of the host antenna does not exceed the gain listed in table 3. This MPE analysis is applicable to any collocated transmitters with transmit power: -less than or equal to 29.0dBm for WLAN/WiMAX; and -less than or equal to 15.0dBm for BT. Specific FCC IDs for those devices are not necessary or identified in this analysis providing they are classified as mobile transmitters. A 100% duty cycle is used for calculations to present a worse-case analysis when applicable. Max Transmitter Maximum Maximum Antenna Gain Equipment Conducted Power (dBi) Mode Transmitter Range Category Duty Cycle (MHz) (dBm) (W) Standalone Collocated 824-849 34.0 2.51 5.5 2.5 GPRS Class10 25% 1850 -1910 31.0 1.26 2.0 2.0 Table 3: HL6528-G2.8V Standalone and Collocated Transmission Declarations

4. MPE Calculations The WWAN MPE calculations are based on conservative conducted transmit power exceeding those listed in the FCC ID N7NHL6528G28V and IC number 2417C-HL6528G28V filing. The higher transmit power levels are used to present a worst case assessment. The WiMAX, WLAN, and BT transmit power and antenna gain parameters represent a maximum transmit power for a given frequency band. Integration of either a WiMAX or WLAN, and BT module that exceeds the parameters requires a new FCC authorization or permissive change application. A maximum antenna gain of 5 dBi for WLAN/WiMAX/BT has been assumed for all collocated antennas. Table 4, 5, and 6 summarize transmitter parameters associated with this analysis.

4.1. Individual Transmitter Calculations 4.1.1. Maximum Output Power The maximum power calculations for HL6528-G2.8V per wireless technology are shown in Table 4 Maximum Maximum Max Maximum Max Max Max Max Frequency Conducted Antenna Duty output Technology Conducted EIRP EIRP ERP ERP (MHz) Power Gain Cycle power Power (W) (dBm) (W) (dBm) (W) (dBm) (dBi) limit HL6528-G2.8V standalone 824-849 34.0 2.51 5.5 1.000 39.500 8.913 37.360 5.445 7 W ERP GPRS 1UL 1850-1910 31.0 1.26 2.0 1.000 33.000 1.995 30.860 1.219 2 W EIRP Table 4: HL6528-G2.8V Maximum Output Power Calculation

4.1.2. Standalone Power Density The power density calculations for the individual transmitters per wireless technology at an exposure minimum separation distance of 20cm are shown in Table 5. For frequency dependent limit, the lowest transmitter frequency was used to represent 2 the lowest MPE limit in this analysis (eg. 824MHz = 0.549mW/cm ) Maximum Maximum Power Maximum Average Average FCC MPE Frequency Conducted Antenna Duty Density @ Technology Conducted EIRP EIRP Limit (MHz) Power Gain Cycle 20cm Power (W) (dBm) (mW) (mW/cm^2) (dBm) (dBi) (mW/cm^2) HL6528-G2.8V standalone 824-849 34.0 2.51 5.5 0.250 33.48 2228.127 0.443 0.549 GPRS 1UL 1850-1910 31.0 1.26 2.0 0.250 26.98 498.816 0.099 1.000 Table 5: HL6528-G2.8V Standalone MPE Calculation

4.2. Collocated MPE Calculation The WiMAX, WLAN, and BT power levels listed represent the worse-case scenario for corresponding frequency ranges given. Maximum Maximum Maximum Average Average Power Density FCC MPE Frequency Duty Technology Conducted Conducted Antenna EIRP EIRP @ 20cm Limit (MHz) Cycle Power (dBm) Power (W) Gain (dBi) (dBm) (mW) (mW/cm^2) (mW/cm^2) HL6528-G2.8V (Collocated) 824-849 34.0 2.51 2.5 0.250 29.98 1116.709 0.222 0.549 module GPRS 1850-1910 31.0 1.26 2.0 0.250 26.98 498.816 0.099 1.000 Table 6: HL6528-G2.8V Collocated MPE Calculation

Per OET Bulletin 65, when RF sources have difference frequencies, the fraction of the FCC power density limit shall be determined and the sum of all fractional components shall be less than 1. WLAN/WiMAX WLAN/WiMAX Pd WLAN/WiMAX + BT Pd (mW/cm^2) Limit Band (GHz) (mW/cm^2) BT Pd (mW/cm^2) 2.3-2.4 2.4-2.5 2.5-2.7 0.500 0.020 0.520 1.000 3.3-3.8 5.15-5.85 Table 7: (WLAN or WiMAX) + BT Collocated MPE Calculation WLAN / WLAN / (WLAN / (850 MHz FCC MPE 850 MHz FCC MPE (WWAN 850 WiMAX WiMAX + WiMAX + BT WWAN + WLAN Limit WWAN Pd Limit MHz) / MPE Limit Pass/Fail Band BT Pd Pd) / (MPE / WiMAX + BT (mW/cm^2) (mW/cm^2) (mW/cm^2) Limit) (GHz) (mW/cm^2) Limit) fraction) 2.3-2.4 2.4-2.5 2.5-2.7 0.520 1.000 0.520 0.222 0.549 0.404 0.924 1.000 Pass 3.3-3.8 5.15-5.85 Table 8: WWAN 850MHz + WLAN / WiMAX + BT Collocated MPE Calculation FCC WLAN / (WLAN / (1900 MHz WLAN / MPE 1900 MHz FCC MPE (WWAN WiMAX WiMAX + BT WWAN + WLAN WiMAX + BT Limit WWAN Pd Limit 1700 MHz) / Limit Pass/Fail Band Pd) / (MPE / WiMAX + BT Pd (mW/cm^2) (mW/c (mW/cm^2) (mW/cm^2) MPE Limit) (GHz) Limit) fraction) m^2) 2.3-2.4 2.4-2.5 2.5-2.7 0.520 1.000 0.520 0.126 1.000 0.126 0.645 1.000 Pass 3.3-3.8 5.15-5.85 Table 9: WWAN 1900MHz + WLAN / WiMAX + BT Collocated MPE Calculation

5. Conclusion Based on FCC OET Bulletin 65 Supplement C and 47 CFR §2.1091, the analysis concludes that the HL6528-G2.8V wireless module, when transmitting either in standalone or simultaneously with other co-located radio transmitters within a host device, is compliant with the FCC/IC RF exposure requirements in mobile exposure condition, provided the conducted power and antenna gain do not exceed the limits in Table 12 for each given frequency band per wireless technology. Maximum Maximum Antenna Gain (dBi) Technology Frequency (MHz) Conducted Power (dBm) Standalone Collocated 824-849 34.0 5.5 2.5 HL65 28-G 2.8V GPRS 1850 -1910 31.0 2.0 2.0 WLAN 2400 -2500 29.0 5.0 WLAN 5150 -5850 29.0 5.0 Transmitters Collocated WiMAX 2300 -2400 29 5.0 WiMAX 2500 -2700 29 5.0 WiMAX 3300 -3800 29 5.0 BT BT 2400 -2500 15 5.0 Table 10: Summary of Maximum Conducted Power and Antenna Gain


Document Created: 2014-05-21 10:48:21
Document Modified: 2014-05-21 10:48:21
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC