10U13412-6A SAR Report

FCC ID: N7N-MHS802

RF Exposure Info

Download: PDF
FCCID_1412543

FCC OET BULLETIN 65 SUPPLEMENT C SAR EVALUATION REPORT (Part 22 & 24) For CDMA+ WIMAX + WIFI MOBILE HOT SPOT MODEL NUMBER: AirCard W802S FCC ID: N7N-MHS802 REPORT NUMBER: 10U13412-6, Revision A ISSUE DATE: JANUARY 12, 2011 Prepared for SIERRA WIRELESS INC. 2200 FARADAY AVE. STE. 150 CARLSBAD, CA 92008 Prepared by COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 Revision History Rev. Issue Date Revisions Revised By -- October 15, 2010 Initial Issue -- A January 12, 2011 Changed model name A. Zaffar Page 2 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................................. 4 2. TEST METHODOLOGY ...................................................................................................................... 5 3. FACILITIES AND ACCREDITATION.................................................................................................. 5 4. CALIBRATION AND UNCERTAINTY................................................................................................. 6 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 6 4.2. MEASUREMENT UNCERTAINTY.............................................................................................. 7 5. SYSTEM SPECIFICATIONS ............................................................................................................... 8 6. COMPOSITION OF INGREDIENTS FOR TISSUE SIMULATING LIQUIDS ...................................... 9 7. TISSUE DIELECTRIC PARAMETERS CHECK ............................................................................... 10 7.1. TISSUE PARAMETERS CHECK RESULTS FOR 835 MHZ .................................................... 11 7.2. TISSUE PARAMETERS CHECK RESULTS FOR 1900 MHZ .................................................. 12 8. SYSTEM VERIFICATION.................................................................................................................. 13 8.1. SYSTEM VERIFICATION RESULTS FOR D835V2 ................................................................. 13 8.2. SYSTEM VERIFICATION RESULTS FOR D1900V2 ............................................................... 13 9. RF OUTPUT POWER VERIFICATION ............................................................................................. 18 9.1. RF POWER OUTPUT FOR 1xRTT........................................................................................... 18 9.2. RF POWER OUTPUT FOR EVDO REL 0 ................................................................................ 20 9.3. RF POWER OUTPUT FOR EVDO REV A................................................................................ 21 10. KDB 941225 TEST REDUCTION CONSIDERATION.................................................................. 22 11. SUMMARY OF TEST RESULTS.................................................................................................. 23 11.1. WORST-CASE SAR PLOTS..................................................................................................... 24 12. KDB 648474 SIMULTANEOUS TRANSMISSION CONSIDERATION ........................................ 28 13. ATTACHMENTS ........................................................................................................................... 29 14. ATENNA LOCATIONS AND SEPARATION DISTANCES .......................................................... 30 15. SAR TEST SETUP PHOTOS ....................................................................................................... 31 1. Top position................................................................................................................................... 31 2. Bottom position ............................................................................................................................. 31 3. Edge position (closest distance).................................................................................................... 32 16. HOST DEVICE PHOTOS.............................................................................................................. 33 Page 3 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 1. ATTESTATION OF TEST RESULTS Applicant name: Sierra Wireless Inc. 200 Faraday Avenue, Suite 150 Carlsbad, CA 92008 EUT description: CDMA+ WIMAX + WIFI MOBILE HOT SPOT Model number: AirCard W802S Device category: Portable Exposure category: General Population/Uncontrolled Exposure Date tested: September 27, 2010 FCC Rule Parts Freq. Range [MHz] The Highest 1g SAR mW/g) Limit (mW/g) 0.791 (Top position) 22H 824 - 849 w/ 10 mm separation distance 1.6 1.20 (Top position) 24E 1850 - 1910 w/ 10 mm separation distance Applicable Standards Test Results FCC OET Bulletin 65 Supplement C 01-01 and the following test procedures: - KDB 648474 D01 SAR Handsets Multi Xmiter and Ant, v01r05 Pass - KDB 941225 D01 SAR test for 3G devices v02 Compliance Certification Services, Inc. (UL CCS) tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by UL CCS based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL CCS and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL CCS will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government (NIST Handbook 150, Annex A). This report is written to support regulatory compliance of the applicable standards stated above. Approved & Released For UL CCS By: Tested By: Sunny Shih Devin Chang Engineering Team Leader EMC Engineer Compliance Certification Services (UL CCS) Compliance Certification Services (UL CCS) Page 4 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with FCC OET Bulletin 65 Supplement C 01-01, and the following specific FCC Test Procedures. - KDB 648474 D01 SAR Handsets Multi Xmiter and Ant, v01r05 - KDB 941225 D01 SAR test for 3G devices v02 3. FACILITIES AND ACCREDITATION The test sites and measurement facilities used to collect data are located at 47173 Benicia Street, Fremont, California, USA. CCS is accredited by NVLAP, Laboratory Code 200065-0. The full scope of accreditation can be viewed at http://www.ccsemc.com. Page 5 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 4. CALIBRATION AND UNCERTAINTY 4.1. MEASURING INSTRUMENT CALIBRATION The measuring equipment utilized to perform the tests documented in this report has been calibrated in accordance with the manufacturer's recommendations, and is traceable to recognized national standards. Cal. Due date Name of Equipment Manufacturer Type/Model Serial No. MM DD Year Robot - Six Axes Stäubli RX90BL N/A N/A Robot Remote Control Stäubli CS7MB 3403-91535 N/A DASY4 Measurement Server SPEAG SEUMS001BA 1041 N/A Probe Alignment Unit SPEAG LB (V2) 261 N/A SAM Phantom (SAM1) SPEAG QD000P40CA 1185 N/A SAM Phantom (SAM2) SPEAG QD000P40CA 1050 N/A Oval Flat Phantom (ELI 4.0) SPEAG QD OVA001 B 1003 N/A Dielectric Probe Kit HP 85070C N/A N/A Thermometer ERTCO 639-1S 1718 7 19 2011 S-Parameter Network Analyzer Agilent 8753ES-6 MY40001647 11 22 2010 Signal Generator Agilent 8753ES-6 MY40001647 11 22 2010 E-Field Probe SPEAG EX3DV4 3531 2 23 2011 Thermometer ERTCO 639-1S 1718 7 19 2011 Data Acquisition Electronics SPEAG DAE3 V1 427 7 21 2011 System Validation Dipole SPEAG D835V2 4d002 4 23 2011 System Validation Dipole SPEAG D1900V2 5d043 11 24 2011 Amplifier Mini-Circuits ZVE-8G 90606 N/A Amplifier Mini-Circuits ZHL-42W D072701-5 N/A Simulating Liquid SPEAG M1900 N/A Within 24 hrs of first test Simulating Liquid SPEAG M835 N/A Within 24 hrs of first test Note: Per KDB 450824 D02 requirements for dipole calibration, UL CCS has adopted two years calibration intervals. On annual basis, each measurement dipole has been evaluated and is in compliance with the following criteria: 1. There is no physical damage on the dipole 2. System validation with specific dipole is within 10% of calibrated value. 3. Return-loss is within 20% of calibrated measurement ( test data on file in UL CCS) 4. Impedance is within 5Ω of calibrated measurement (test data on file in UL CCS ) Page 6 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 4.2. MEASUREMENT UNCERTAINTY Measurement uncertainty for 300 MHz to 3 GHz averaged over 1 gram Component error, % Probe Distribution Divisor Sensitivity U (Xi), % Measurement System Probe Calibration (k=1) @ Body 835 MHz 5.50 Normal 1 1 5.50 Axial Isotropy 1.15 Rectangular 1.732 0.7071 0.47 Hemispherical Isotropy 2.30 Rectangular 1.732 0.7071 0.94 Boundary Effect 0.90 Rectangular 1.732 1 0.52 Probe Linearity 3.45 Rectangular 1.732 1 1.99 System Detection Limits 1.00 Rectangular 1.732 1 0.58 Readout Electronics 0.30 Normal 1 1 0.30 Response Time 0.80 Rectangular 1.732 1 0.46 Integration Time 2.60 Rectangular 1.732 1 1.50 RF Ambient Conditions - Noise 3.00 Rectangular 1.732 1 1.73 RF Ambient Conditions - Reflections 3.00 Rectangular 1.732 1 1.73 Probe Positioner Mechanical Tolerance 0.40 Rectangular 1.732 1 0.23 Probe Positioning with respect to Phantom 2.90 Rectangular 1.732 1 1.67 Extrapolation, Interpolation and Integration 1.00 Rectangular 1.732 1 0.58 Test Sample Related Test Sample Positioning 2.90 Normal 1 1 2.90 Device Holder Uncertainty 3.60 Normal 1 1 3.60 Output Power Variation - SAR Drift 5.00 Rectangular 1.732 1 2.89 Phantom and Tissue Parameters Phantom Uncertainty (shape and thickness) 4.00 Rectangular 1.732 1 2.31 Liquid Conductivity - deviation from target 5.00 Rectangular 1.732 0.64 1.85 Liquid Conductivity - measurement 2.09 Normal 1 0.64 1.34 Liquid Permittivity - deviation from target 5.00 Rectangular 1.732 0.6 1.73 Liquid Permittivity - measurement 1.54 Normal 1 0.6 0.92 Combined Standard Uncertainty Uc(y) = 9.58 Expanded Uncertainty U, Coverage Factor = 2, > 95 % Confidence = 19.16 % Expanded Uncertainty U, Coverage Factor = 2, > 95 % Confidence = 1.52 dB Page 7 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 5. SYSTEM SPECIFICATIONS The DASY4 system for performing compliance tests consists of the following items: • A standard high precision 6-axis robot (Stäubli RX family) with controller, teach pendant and software. An arm extension for accommodating the data acquisition electronics (DAE). • A dosimetric probe, i.e., an isotropic E-field probe optimized and calibrated for usage in tissue simulating liquid. The probe is equipped with an optical surface detector system. • A data acquisition electronics (DAE) which performs the signal amplification, signal multiplexing, AD-conversion, offset measurements, mechanical surface detection, collision detection, etc. The unit is battery powered with standard or rechargeable batteries. The signal is optically transmitted to the EOC. • The function of the measurement server is to perform the time critical tasks such as signal filtering, control of the robot operation and fast movement interrupts. • A probe alignment unit which improves the (absolute) accuracy of the probe positioning. • A computer operating Windows 2000 or Windows XP. • DASY4 software. • Remote controls with teach pendant and additional circuitry for robot safety such as warning lamps, etc. • The SAM twin phantom enabling testing left-hand and right-hand usage. • The device holder for handheld mobile phones. • Tissue simulating liquid mixed according to the given recipes. • Validation dipole kits allowing to validate the proper functioning of the system. Page 8 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 6. COMPOSITION OF INGREDIENTS FOR TISSUE SIMULATING LIQUIDS The following tissue formulations are provided for reference only as some of the parameters have not been thoroughly verified. The composition of ingredients may be modified accordingly to achieve the desired target tissue parameters required for routine SAR evaluation. Ingredients Frequency (MHz) (% by weight) 450 835 915 1900 2450 Tissue Type Head Body Head Body Head Body Head Body Head Body Water 38.56 51.16 41.45 52.4 41.05 56.0 54.9 40.4 62.7 73.2 Salt (NaCl) 3.95 1.49 1.45 1.4 1.35 0.76 0.18 0.5 0.5 0.04 Sugar 56.32 46.78 56.0 45.0 56.5 41.76 0.0 58.0 0.0 0.0 HEC 0.98 0.52 1.0 1.0 1.0 1.21 0.0 1.0 0.0 0.0 Bactericide 0.19 0.05 0.1 0.1 0.1 0.27 0.0 0.1 0.0 0.0 Triton X-100 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 36.8 0.0 DGBE 0.0 0.0 0.0 0.0 0.0 0.0 44.92 0.0 0.0 26.7 Dielectric Constant 43.42 58.0 42.54 56.1 42.0 56.8 39.9 54.0 39.8 52.5 Conductivity (S/m) 0.85 0.83 0.91 0.95 1.0 1.07 1.42 1.45 1.88 1.78 Salt: 99+% Pure Sodium Chloride Sugar: 98+% Pure Sucrose Water: De-ionized, 16 MΩ+ resistivity HEC: Hydroxyethyl Cellulose DGBE: 99+% Di(ethylene glycol) butyl ether, [2-(2-butoxyethoxy)ethanol] Triton X-100 (ultra pure): Polyethylene glycol mono [4-(1,1, 3, 3-tetramethylbutyl)phenyl]ether Page 9 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 7. TISSUE DIELECTRIC PARAMETERS CHECK The simulating liquids should be checked at the beginning of a series of SAR measurements to determine of the dielectric parameters are within the tolerances of the specified target values. For frequencies in 300 MHz to 2 GHz, the measured conductivity and relative permittivity should be within ± 5% of the target values. For frequencies in the range of 2–3 GHz and above the measured conductivity should be within ± 5% of the target values. The measured relative permittivity tolerance can be relaxed to no more than ± 10%. Reference Values of Tissue Dielectric Parameters The body tissue parameters that have not been specified in IEEE Std 1528 are derived from the tissue dielectric parameters computed from the 4-Cole-Cole equations and extrapolated according to the head parameters specified in IEEE Std 1528. Body Target Frequency (MHz) ¬r ¬ (S/m) 150 61.9 0.8 300 58.2 0.92 450 56.7 0.94 835 55.2 0.97 900 55 1.05 915 55 1.06 1450 54 1.3 1610 53.8 1.4 1800 – 2000 53.3 1.52 2450 52.7 1.95 3000 52 2.73 5800 48.2 6 (εr = relative permittivity, σ = conductivity and ρ = 1000 kg/m3) Page 10 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 7.1. TISSUE PARAMETERS CHECK RESULTS FOR 835 MHZ Simulating Liquid Dielectric Parameter Check Result @ Body 835 MHz Measured by: Devin Chang f (MHz) Liquid Parameters Measured Target Delta (%) Limit (%) e' 56.05 Relative Permittivity (єr): 56.052 55.2 1.54 ±5 835 e" 21.32 Conductivity (σ): 0.990 0.97 2.09 ±5 Liquid Check Ambient temperature: 24 deg. C; Liquid temperature: 23 deg. C; Relative humidity = 39% September 27, 2010 15:03 PM Frequency e' e'' 790000000. 56.3945 21.8003 795000000. 56.3613 21.7732 800000000. 56.3435 21.7197 805000000. 56.2978 21.6906 810000000. 56.2914 21.5857 815000000. 56.2526 21.5309 820000000. 56.2163 21.4706 825000000. 56.1447 21.3937 830000000. 56.0717 21.3457 835000000. 56.0523 21.3189 840000000. 56.0123 21.2856 845000000. 55.9246 21.2612 850000000. 55.8570 21.2218 855000000. 55.8030 21.2203 860000000. 55.7645 21.2281 865000000. 55.7050 21.2746 870000000. 55.6266 21.2921 875000000. 55.5394 21.3063 880000000. 55.5200 21.3130 885000000. 55.4320 21.3504 890000000. 55.3627 21.3337 895000000. 55.3424 21.2936 900000000. 55.3241 21.2701 905000000. 55.3250 21.1964 910000000. 55.3343 21.1656 915000000. 55.3401 21.0765 920000000. 55.3163 21.0311 925000000. 55.3279 20.9862 930000000. 55.2992 20.9444 935000000. 55.2732 20.9055 940000000. 55.2477 20.9007 945000000. 55.1822 20.9120 950000000. 55.1228 20.9032 955000000. 55.0377 20.9191 The conductivity (σ) can be given as: σ = ωε0 e''= 2 π f ε0 e'' where f = target f * 106 ε0 = 8.854 * 10-12 Page 11 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 7.2. TISSUE PARAMETERS CHECK RESULTS FOR 1900 MHZ Simulating Liquid Dielectric Parameter Check Result @ Body 1900 MHz Measured by: Devin Chang f (MHz) Muscle Liquid Parameters Measured Target Delta (%) Limit (%) e' 53.753 Relative Permittivity (єr): 53.7532 53.3 0.85 ±5 1900 e" 14.232 Conductivity (σ): 1.50436 1.52 -1.03 ±5 Liquid Check Ambient temperature: 24 deg. C; Liquid temperature: 23 deg. C; Relative humidity = 39% September 27, 2010 08:03 AM Frequency e' e'' 1710000000. 54.4118 13.5844 1720000000. 54.3789 13.6179 1730000000. 54.3659 13.6491 1740000000. 54.3360 13.7090 1750000000. 54.3085 13.7307 1760000000. 54.2601 13.7753 1770000000. 54.2191 13.8029 1780000000. 54.1722 13.8243 1790000000. 54.1300 13.8609 1800000000. 54.0906 13.9031 1810000000. 54.0491 13.9500 1820000000. 54.0146 13.9884 1830000000. 53.9647 14.0225 1840000000. 53.9406 14.0610 1850000000. 53.9062 14.1042 1860000000. 53.8905 14.1249 1870000000. 53.8639 14.1637 1880000000. 53.8241 14.1866 1890000000. 53.7912 14.2174 1900000000. 53.7532 14.2324 1910000000. 53.7015 14.2664 The conductivity (σ) can be given as: σ = ωε0 e''= 2 π f ε0 e'' where f = target f * 106 ε0 = 8.854 * 10-12 Page 12 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 8. SYSTEM VERIFICATION The system performance check is performed prior to any usage of the system in order to verify SAR system measurement accuracy. The system performance check verifies that the system operates within its specifications of ±10%. Measurement Conditions • The measurements were performed in the flat section of the SAM twin phantom filled with Head or Body simulating liquid of the following parameters. • The DASY4 system with an Isotropic E-Field Probe EX3DV3-SN: 3531 was used for the measurements. • The dipole was mounted on the small tripod so that the dipole feed point was positioned below the center marking of the flat phantom section and the dipole was oriented parallel to the body axis (the long side of the phantom). The standard measuring distance was 10 mm (above 1 GHz) and 15 mm (below 1 GHz) from dipole center to the simulating liquid surface. • The coarse grid with a grid spacing of 15 mm was aligned with the dipole. For 5 GHz band - The coarse grid with a grid spacing of 10 mm was aligned with the dipole. • Special 7x7x7 fine cube was chosen for cube • Distance between probe sensors and phantom surface was set to 3 mm. For 5 GHz band - Distance between probe sensors and phantom surface was set to 2.5 mm • The dipole input power (forward power) was 100 mW • The results are normalized to 1 W input power. Reference SAR Values for HEAD & BODY-tissue from calibration certificate of SPEAG. System Cal. SAR Avg (mW/g) Cal. certificate # validation dipole date Tissue: Head Body SAR1g: 9.64 9.96 D835V2 D835V2-4d002_Apr09 4/23/09 SAR10g: 6.28 6.56 SAR1g: 39.8 40.4 D1900V2 D1900V2-5d043_Nov09 11/24/09 SAR10g: 20.7 21.4 8.1. SYSTEM VERIFICATION RESULTS FOR D835V2 Ambient Temperature = 24°C; Relative humidity = 40% Measured by: Devin Chang System Measured (Normalized to 1 W) Tolerance Date Tested Target Delta (%) validation dipole Tissue: Body (%) SAR1g: 10.2 9.96 2.41 D835V2 9/27/10 ±10 SAR10g: 6.75 6.56 2.90 8.2. SYSTEM VERIFICATION RESULTS FOR D1900V2 Ambient Temperature = 24°C; Relative humidity = 35% Measured by: Devin Chang System Measured (Normalized to 1 W) Tolerance Date Tested Target Delta (%) validation dipole Tissue: Body (%) SAR1g: 40.7 40.4 0.74 D1900V2 9/27/10 ±10 SAR10g: 21.6 21.4 0.93 Page 13 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

on Datertime. s272010 32557 PM Test Latoretoy: Compience Cortfeaton Servces System Performance Check — DB35V2 DUT: Dile 235 iz Type: DBJ5V2 Seral DeSSV2 — Stt Communicaton System: CW 635. Frequency: 635 HeDuty Cyole 11 Medum porametars use (= 235Mc o = 090 mhaim, 5 = 58 1. = 1000 kyim® Pranion secton: Flt Secton Reom Ambient Temperature 24.0 deg. . Ligud Temperatire 220 deg. C DASY4 Confguraton —Area Scan seting — Find Secondary Maximum Wihin 20 6B and with a peak SAR value greatethan 0.0012Wikg —Brove Exa0Va— SN2Sat, ConF(10 18, 10 18, 10 18) Calivated 2222010 — SensorSurface omm (Mechanical Surface Delecion) —Electonics DAE® Snd27.Caibrates 7evrzor0 ~Pnantom: SAM2 (Tuir) Tyge SAM 2: Serat 1050 —Meassrement SW DASY4, V4 7 Buld B0Postprocessing SW SENCAD, V Buid tos d=15mm, Pin=100 mW!Area Scan (7X9x1): Meassement i. de=tSnm,dy=1Snm Maximum valueof SAR (neasized) = 118 mlg d=15mm, Pin=100 mWIZoom Scan (7x7x7)/Cube 0: Measwrement gid deeSm, dy—Smm, Sim Reterance Vae 242 Vim, Power Drit = 0054 d Peak SAR (ertapolated) = 152 Wiko SAR(T 9 = 102 milly; SAR(TO g) = 07 mWig Maximum valueof SAR (mcasired) = 120 minig mW 116 ssm acroe vare s2n aore tramie l.0... Jose

on Datertime: samiz0r0 2 5 as pm Test Latoretoy: Complance Contfcaton Senices System Performance Check — DB3GV2 DUT: Dile 235 iz Type: DB3SV2. Seral DeJS2— Shoox Communicaton System: CW 835, Frequency: 835 itz Duty Cyole 11 d=15mm, Pin=100 mWIZ Scan (1x1x34): Meassrementgi. d=20mm, dy=20mm. dz=3nm Maximumvave of SAR (measired = 1.19 miWg SAR(Gcy,2.0) canymt dnes, wen v.o 12 w 10 ts ts e« 8 oo e co olo ob on ols o ols oie oir ols ols cio Jeavsto sso

an Datertime: smt20r0 8 :17 an Test Latoretoy: Complance Contfcaton Snvices System Performance Check — D1900V2 DUT. Dile,Type: D1900v2. Serat scors Communicaton System: System Check Signal— CW,Frequency: 1900 Mz Duty Cycle: 111 Medum parametersused.1= 1900 MKza = 1. mhoim , 538. o = 1000 kyim® Pranion secton: Flt Sectin Reom Ambient Temperature. 250 deg. ; Liqué Temperatre 240 deg. C DASY4 Confguraton — Area Scan seting — Find Seconday Maximum Witin. 20 48 and wih a peak SAR value greatethan 00012Who —Brove Ex2DVa— SNaS3t: ConyE(204, 804 804) Calivaled 2222010 — SensorSurface omm (Mechanical Sulace Detecton) — Eectonics DAE® Sndzr. Caltrated 7212010 —Pnantom: SAM2 (Tuiny Tyge SAM2 Senal 1050 —Meassrement SW DASY4, V4 7 Build 60 Poslprocessng SW SENCAD, V Buid tos d=10mm, Pin=100mW!Area Scan (7X7x1): Messurement grc. 6 Smm. dy=1Smm Maximum valueof SAR (measured) = 378 mio d=10mm, Pin=100mW/Zoom Scan (7x7x7)/Cube 0: Measwrement gid desmm, dy—nm, se=Smm Refernce Value= 58 1 Vim, Power Drit = 0080 dB Peas SAR (exrapobted SaR(1 q = 407 mt mW 378 ans 227 18e acres n.ons Jeavste isea

on Datertime: s2miz0r0 a se s an Test Latortoy: Complance Contfcaton Sanices System Performance Check — D1900V2 DUT. Diie,Type: D1900V2Serat saors Gommunaton System: System Gnex Sgnat— CW,Frequency. 1900 mtz Duty Cyoe: 11 d=10mm, Pin=100mWIZ Scan (1x1x34): Measurement grd. t20mm, dy—20mm, de—trim Maximum vaiueof SAR (measured) = 5.14 mMig SARGcyz.M) canyt tnntine lover, so \ «s \ «o is 10 is o sofucc on ol rc_ hitrren i olo ob ob ols o oi uds ogr ols ols cio — ce n — — meanto wevuccs= — — — — —ss80 dn repn s i n repvamwse unvign ns way m nvin vimm umm uni ue ue uon

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 9. RF OUTPUT POWER VERIFICATION Maximum output power is verified on the Low, Middle and High channels according to procedures in section 4.4.5.2 of 3GPP2 C.S0011/TIA-98-E for 1xRTT, section 3.1.2.3.4 of 3GPP2 C.S0033-0/TIA-866 for Rel. 0 and section 4.3.4 of 3GPP2 C.S0033-A for Rev. A 9.1. RF POWER OUTPUT FOR 1xRTT This procedure assumes the Agilent 8960 Test Set has the following applications installed and with valid license. Application Rev, License CDMA2000 Mobile Test B.13.08, L • Call Setup > Shift & Preset • Cell Info > Cell Parameters > System ID (SID) > 8 > Network ID (NID) > 65535 • Protocol Rev > 6 (IS-2000-0) • Radio Config (RC) > Please see following table or details • FCH Service Option (SO) Setup > Please see following table or details • Traffic Data Rate > Full • TDSO SCH Info > F-SCH Parameters > F-SCH Data Rate > 153.6 kbps > R-SCH Parameters > R-SCH Data Rate > 153.6 kbps • Rvs Power Ctrl > Active bits o Rvs Power Ctrl > All Up bits (Maximum TxPout) RF Output Power for Cellular Band Radio Conducted Output Power (dBm) Configuration Service Option Ch. 1013 / 824.7 MHz Ch. 384 / 836.52 MHz Ch. 777 / 848.31 MHz (RC) (SO) Average Average Average 2 (Loopback) 23.7 23.8 23.7 RC1 55 (Loopback) 23.8 23.9 23.8 9 (Loopback) 23.7 23.8 23.7 RC2 55 (Loopback) 23.7 23.8 23.7 2 (Loopback) 23.8 23.9 23.7 55 (Loopback) 23.8 23.9 23.7 RC3 32 (+ F-SCH) 23.8 23.9 23.7 32 (+ SCH) 23.8 23.9 23.7 2 (Loopback) 23.8 23.9 23.7 55 (Loopback) 23.8 23.9 23.7 RC4 32 (+ F-SCH) 23.8 23.9 23.7 32 (+ SCH) 23.7 23.9 23.7 9 (Loopback) 23.8 23.9 23.7 RC5 55 (Loopback) 23.8 23.9 23.7 Page 18 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 RF Output Power for PCS Band Radio Conducted Output Power (dBm) Configuration Service Option Ch. 25 / 1851.25 MHz Ch. 600 / 1880 MHz Ch. 1175 / 1908.75 MHz (RC) (SO) Average Average Average 2 (Loopback) 24.2 24.2 23.8 RC1 55 (Loopback) 24.2 24.2 23.8 9 (Loopback) 24.2 24.1 23.8 RC2 55 (Loopback) 24.2 24.2 23.9 2 (Loopback) 24.2 24.2 23.8 55 (Loopback) 24.2 24.2 23.8 RC3 32 (+ F-SCH) 24.3 24.2 23.9 32 (+ SCH) 24.3 24.2 23.9 2 (Loopback) 24.1 24.2 23.8 55 (Loopback) 24.2 24.1 23.9 RC4 32 (+ F-SCH) 24.2 24.2 23.9 32 (+ SCH) 24.3 24.2 23.9 9 (Loopback) 24.2 24.2 23.8 RC5 55 (Loopback) 24.2 24.2 23.7 Page 19 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 9.2. RF POWER OUTPUT FOR EVDO REL 0 This procedure assumes the Agilent 8960 Test Set has the following applications installed and with valid license. Application Rev, License 1xEV-DO Terminal Test A.09.13 EVDO Release 0 - RTAP • Call Setup > Shift & Preset • Call Control: o Access Network Info > Cell Parameters > Sector ID > 00000000 > Subnet Mask > 0 o Generator Info > Termination Parameters > Max Forward Packet Duration > 16 Slots • Call Parms: o Cell Power > -105.5 dBm/1.23 MHz o Cell Band > (Select US Cellular or US PCS) o Channel > (Enter channel number) o Application Config > Enhanced Test Application Protocol > RTAP o RTAP Rate > 153.6 kbps o Rvs Power Ctrl > Active bits o Protocol Rel > 0 (1xEV-DO) • Press “Start Data Connection” when “Session Open” appear in “Active Cell” • Rvs Power Ctrl > All Up bits (Maximum TxPout) EVDO Release 0 - FTAP • Call Setup > Shift & Preset • Call Control: o Access Network Info > Cell Parameters > Sector ID > 00000000 > Subnet Mask > 0 o Generator Info > Termination Parameters > Max Forward Packet Duration > 16 Slots • Call Parms: o Cell Power > -105.5 dBm/1.23 MHz o Cell Band > (Select US Cellular or US PCS) o Channel > (Enter channel number) o Application Config > Enhanced Test Application Protocol > FTAP (default) o FTAP Rate > 307.2 kbps (2 Slot, QPSK) o Rvs Power Ctrl > Active bits o Protocol Rel > 0 (1xEV-DO) • Press “Start Data Connection” when “Session Open” appear in “Active Cell” • Rvs Power Ctrl > All Up bits (Maximum TxPout) RF Power Output for EV-DO Rel 0 Cell Band Conducted pwr (dBm) FTAP Rate RTAP Rate Channel f (MHz) Average 307.2 kbps 1013 824.70 23.7 (2 slot, 153.6 kbps 384 836.52 23.8 QPSK) 777 848.31 23.7 PCS Band Conducted pwr (dBm) FTAP Rate RTAP Rate Channel f (MHz) Average 307.2 kbps 25 1851.25 24.3 (2 slot, 153.6 kbps 600 1880.00 24.1 QPSK) 1175 1908.75 23.8 Page 20 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 9.3. RF POWER OUTPUT FOR EVDO REV A This procedure assumes the Agilent 8960 Test Set has the following applications installed and with valid license. Application Rev, License 1xEV-DO Terminal Test A.09.13 EVDO Release A – RETAP • Call Setup > Shift & Preset • Cell Power > -60 dBm/1.23 MHz • Protocol Rev > A (1xEV-DO-A) • Application Config > Enhanced Test Application Protocol > RETAP • R-Data Pkt Size > 4096 • Protocol Subtype Config > Release A Physical Layer Subtype > Subtype 2 > PL Subtype 2 Access Channel MAC Subtype > Default (Subtype 0) • Access Network Info > Cell Parameters > Sector ID > 00000000 > Subnet Mask > 0 • Generator Info > Termination Parameters > Max Forward Packet Duration >16 Slots > ACK R-Data After > Subpacket 0 (All ACK) • Rvs Power Ctrl > All Up bits (to get the maximum power) EVDO Release A - FETAP • Call Setup > Shift & Preset • Cell Power > -60 dBm/1.23 MHz • Protocol Rev > A (1xEV-DO-A) • Application Config > Enhanced Test Application Protocol > FETAP • F-Traffic Format > 4 (1024, 2,128) Canonical (307.2k, QPSK) • Protocol Subtype Config > Release A Physical Layer Subtype > Subtype 2 > PL Subtype 2 Access Channel MAC Subtype > Default (Subtype 0) • Access Network Info > Cell Parameters > Sector ID > 00000000 > Subnet Mask > 0 • Generator Info > Termination Parameters > Max Forward Packet Duration >16 Slots > ACK R-Data After > Subpacket 0 (All ACK) • Rvs Power Ctrl > All Up bits (to get the maximum power) RF Power Output Results for EV-DO Rev A Cell Band RETAP-Data Conducted pwr (dBm) FETAP-Traffic Format Payload Size Channel f (MHz) Average 307.2k, QPSK/ ACK 1013 824.70 23.8 channel is transmitted at 4096 384 836.52 23.9 all the slots 777 848.31 23.8 PCS Band RETAP-Data Conducted pwr (dBm) FETAP-Traffic Format Payload Size Channel f (MHz) Average 307.2k, QPSK/ ACK 25 1851.25 24.2 channel is transmitted at 4096 600 1880.00 24.1 all the slots 1175 1908.75 23.9 Page 21 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 10. KDB 941225 TEST REDUCTION CONSIDERATION CDMA2000 1x handsets Test configurations based on KDB 941225 SAR test for 3G devices v02 Body SAR 1. SAR for RC3 1) With DUT configured using TDSO/SO32, to transmit at full rate on FCH with all other code channels disabled. 2) For multiples code channels (FCH + SCHn) (1) Not required when the maximum average output of each RF channel is less than 0.25 dB higher than as measured with FCH only. (2) Else SAR is measured on the maximum output channel (FCH + SCHn) with FCH at full rate and SCH0 enabled at 9600 bps, for exposure configuration that produced highest SAR for that channel with FCH only. 2. SAR for RC1 1) Not required when the maximum average output of each channel is less than 0.25 dB higher than as measured in RC3. 2) Else SAR is measured on the maximum output channel in RC1, with Loopback Service Option SO55, at full rate, for exposure configuration that produced highest SAR for that channel in RC3. 3. Handsets with Ev-Do 1) SAR for Release 0 (Rel. 0) (1) Not required when the maximum average output of each channel is less than 0.25 dB higher than as measured in RC3 (1xRTT) (2) Else SAR is measured on the maximum output channel, at 153.6 kbps, for exposure configuration that produced highest SAR for that channel in RC3. 2) SAR for Revision A (Rev. A) (1) Not required when the maximum average output of each channel is less than as measured in Release 0, or is lees than 0.25 dB higher than as measured in RC3 (1xRTT). (2) Else SAR is measured on the maximum output channel, using a Reverse Data Channel payload size of 4096 bits and a Termination Target of 16 slots defined for Subtype 2 Physical Layer configurations (TBD: may be “for exposure configuration that produced highest SAR for that channel in RC3”) Notes: Based upon the power measurement in section 9.1, SAR for multiple code channel (FCH+SCH) is not required due to the output power is not ¼ dB higher than RC3/SO32. Based upon the power measurement in section 9.2 and 9.3, SAR for 1xEVDO Rel. 0 and Rev. A power measurement is not ¼ dB higher than RC3. Thus, RC3/SO32 is used for all body SAR measurement. Page 22 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 11. SUMMARY OF TEST RESULTS 1. Top position Band Mode UL Ch No. f (MHz) SAR (mW/g) 1-g 10-g 1013 824.70 1xRTT 384 836.52 0.791 0.526 Cellular (RC3, SO32) 777 848.31 1xRTT(RC3, SO55) 384 836.52 0.765 0.513 25 1851.25 0.899 0.588 1xRTT 600 1880.00 1.200 0.779 PCS (RC3, SO32) 1175 1908.75 0.879 0.559 1xRTT(RC3, SO55) 600 1880.00 1.160 0.760 2. Bottom position Band Mode UL Ch No. f (MHz) SAR (mW/g) 1-g 10-g 1013 824.70 1xRTT Cellular 384 836.52 0.776 0.517 (RC3, SO32) 777 848.31 25 1851.25 0.857 0.564 1xRTT PCS 600 1880.00 1.120 0.731 (RC3, SO32) 1175 1908.75 0.797 0.509 3. Edge position Band Mode UL Ch No. f (MHz) SAR (mW/g) 1-g 10-g 1013 824.70 1xRTT Cellular 384 836.52 0.182 0.112 (RC3, SO32) 777 848.31 25 1851.25 0.603 0.351 1xRTT PCS 600 1880.00 0.915 0.528 (RC3, SO32) 1175 1908.75 0.784 0.446 Page 23 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

m Datertine sereoro «1211 pa TestLaboratoy: Complance Contfcaton Sanvices Cell 850_Top mode DUT, Serra Wreless, Type NA Seral NA Communication System: CONMA Call Bang, Frequency: 28 52 IMHeDutyCycle 11 Medum parametarsused (nterpolated) «638 52 MHe: a 0 982 mhoim,= 56 o = 1000 kain® Prarto secton:Flt Secton Reon Anbient Temperature. 240 deg. ; LidTemperatre 230 deg. C DASr4 Contguraton —Area Scan seting — Find Seconday Maxinum Within 20 48 and wih a peak SAR value greatethan 0O012Who — Probe EX2DV3— SN2S31; ConnE(10 18 10.10, 10 10)Calbeated 2222010 — SemsorBurtace amm (Mechanical Surface Detecion) —Eectronics DAE® Snd27. Caltrated 7212010 ~Pnanm: SAM2 (Tuin)Tyge SAM2 Seral 1oso —Measurement SW DASY4, V4 7 Buld 60Postrocessng SW SENCAD, V Buid tos 1xRTT $032_M—ch/Area Scan {9x8x1 ): Measwement i. dc=tSrmdy=15mm In Interpolated meciur parametersusedfor SAR avaiuaton Maxmumvaiveof SAR (measured)= 0802 mWig 1xRTT $032_M—ch/zoom Scan (7x7x8)/Cube Measurement gid. eeSmim, y—Smm. de=2nm Reterence Vakve ©20.4 Vim, Power Drft =—0 130 dB Peat SAR (exrapoited) 119 Wio SARCT 9) = 0701 mivig SARCTO ) = 0.528 muv‘g Ino Inlerpolated mediur parametersused fr SA avaiuaton Maximum vaiueof SAR (measured) 0918 mWiy mds £.393 sns aser use a100 nore Te mm mm mm en n mm on nage

m Datertime a2rot0 7—15 34 pm Test Latoretoy: Complance CertfeatonServices Cell 850_Top mode DUT: Sre Wreless, Type NX Seral NA Communicaton System COMA Call Band. Frequency 238 52 MHHz Duty Cycle 11 1xRTT $032_M—ch/Z Scan (1x1x23): Measrement i. d=20nm,dy20nm.6z=3 5mm Ino: Interpolated medium parametersused fr SAR evaluaton Maximumvae of SAR (mcasired) = 0870 mWig SARGcyz.M) un tnntie livet, co « E__l sofuccl Loo Fuca hoacl ud dotbrens i olo ob ob ols ob ads nds oir ols on oi Jeacsre se

m Datertime: smizor0 101824 a fest Latorstary. Gomptance Genttcaton owces PCS 1900_Top mode DUT. Sara Wreless, Type NA Seral NA Communicaton System: COMA PGS Band. Frequency: 1880 WzDuty Cycle 11 Medun parameters used. (= 1080 Mz = 1 48 mhaim, 5 588, o = 1000 kain Pranion secton Fat Secton Reom Ambint Temperature 24 0 deg. ; Liqué Temperatre 230 deg. C DASY4 Corfquaton — Area Scan ettng—Find Seconday Maximum Witin. 20 08 and wih a peak SAR value greatethan 00012Wkg —Prove Ex30V3 — sNas3t, ConyF(@04, 804 804) Calivaled 22302010 — SensorSuface 2mm (Mechanical Surlace Delecion) — Elecvonics DAE Snd27. Caltrated 7212010 —Pnartom: SAM 2 (Twiny Tyge SAM2 Senal 1050 —Meassrement SW DAS4, V4 7 Build 60 Postrocessng SW SEMCAD, V Buid tos 1xRTT $032_M—ch/Area Scan (Bx9x1): Measrament grd. dc=1Snm,dy=1mm Maximum valu of SAR (measured) = 141 mMig 1xRTT $032_M—ch/Zoom Scan (7XTX)/Cuibe 0: Meassrement gid. cx—Smm,dj—Smm, dz—3mm Refernce Value ©309 Vim, Pover Drtt =—0.179 dB Peak SAR (extepciated) = 1 75 Wio SaRI1 ) =1.2 miilg: Santt0 ol .779 mhig Marinum vae of SAR (measurec) 138 mW wl rat sam ases azes scone weavste se

an Datertime: smizor0 10.«2:18 An Test Latorstoy: Complance Contfcaton Senvices PCS 1900_Top mode DUT: Sre Wreless; Type NA Seral NA Communicaton System: CMA PCS Band, Freguency. 1000 MEHz.Duty Cycl 11 1xRTT $032_M—ch/Z Scan (1x1x23): Measrement i. d=20nm,dy—20nm.6z=3 5mm Maximumvae of SAR (measired 1 35 mW SAR(cyz.0) uns tm lime,wenvo 1« 12 10 \ use & is c« 62 \\ sohcoch oo hocl hocs bvtorerres i slo ob oiz ob ol uds ols olr ols o on Jeavste isea

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 12. KDB 648474 SIMULTANEOUS TRANSMISSION CONSIDERATION SUMMARY OF SAR EVALUATION FOR HANDSET DEVICE WITH MULTIPLE TRANSMITTERS Individual Transmitter Stand-alone SAR WWAN Yes WiFi Yes WiMAX Yes SIMULTANEOUS TRANSMISSION • WWAN can transmit simultaneously with WiFi • WWAN can not transmit simultaneously with WiMAX Highest SAR value and the sum of the 1-g SAR for WWAN & WiFi Highest 1-g SAR (W/kg) ∑ 1-g SAR (W/kg) WWAN WiFi Part 22 0.791 0.991 0.200 Part 24 1.12 1.320 ` CONCLUSION: Simultaneous transmission Require for Simultaneous Transmission SAR with volume scans WWAN & WiFi No (the sum of the 1-g SAR is < 1.6 W/kg) WWAN & WiMAX No (WWAN can not transmit simultaneously with WiMAX) Page 28 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 10U13412-6A DATE: JANUARY 12, 2011 FCC ID: N7N-MHS802 13. ATTACHMENTS No. Contents No. of page (s) 1-1 SAR Test Plots for Cellular band 5 1-2 SAR Test Plots for PCS band 11 2 Certificate of E-Field Probe - EX3DV3 SN3531 11 3 Certificate of System Validation Dipole D835V2 SN:4d002 9 4 Certificate of System Validation Dipole D1900V2 SN:5d043 9 Page 29 of 33 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.


Document Created: 2011-01-18 08:35:47
Document Modified: 2011-01-18 08:35:47
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC