Test Report

FCC ID: N73-EX09

Test Report

Download: PDF
FCCID_2791850

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. 588 West Jindu Road,Songjiang District,Shanghai,China Telephone: +86 (0) 21 6191 5666 Fax: +86 (0) 21 6191 5678 Report No.: SHEM141100297201 ee.shanghai@sgs.com Page: 1 of 18 1 Cover Page FCC REPORT Application No.: SHEM1411002972RF Applicant: MINE SITE TECHNOLOGIES PTY LTD FCC ID: N73-EX09 Equipment Under Test (EUT): NOTE: The following sample(s) submitted was/were identified on behalf of the client as Product Name: Exciter Model No.(EUT): EX09 Standards: FCC PART 15 Subpart C: 2014 Date of Receipt: November 21, 2014 Date of Test: November 28, 2014 to August 29, 2015 Date of Issue: August 29, 2015 Test Result: Pass* *In the configuration tested, the EUT detailed in this report complied with the standards specified above. Parlam Zhan E&E Section Manager SGS-CSTC (Shanghai) Co., Ltd. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 2 of 18 2 Version Revision Record Version Chapter Date Modifier Remark 00 / December 30, 2014 / Original Authorized for issue by: Engineer Eddy Zong Print Name Clerk Susie Liu Print Name Reviewer Keny Xu Print Name This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 3 of 18 3 Test Summary Test Item Test Requirement Test method Result 47 CFR Part 15, Subpart C Antenna Requirement - PASS Section 15.203 AC Power Line Conducted 47 CFR Part 15, Subpart C ANSI C63.10(2013) N/A Emission Section 15.207 Section 6.2 47 CFR Part 15, Subpart C ANSI C63.10(2013) Radiated Emissions Section PASS Section 15.209 6.4&6.5&6.6&6.10 47 CFR Part 15, Subpart C ANSI C63.10(2013) 20dB Bandwidth PASS Section 15.215 Section 6.9.2 N/A: Not applicable, please refer to Section 7.2 of this report for details. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 4 of 18 4 Contents Page 1 COVER PAGE .................................................................................................................................................. 1 2 VERSION ........................................................................................................................................................... 2 3 TEST SUMMARY ............................................................................................................................................. 3 4 CONTENTS ....................................................................................................................................................... 4 5 GENERAL INFORMATION ............................................................................................................................ 5 5.1 CLIENT INFORMATION ................................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF E.U.T. ................................................................................................................ 5 5.3 TECHNICAL SPECIFICATIONS: ........................................................................................................................ 5 5.4 E.U.T OPERATION MODE .............................................................................................................................. 5 5.5 DESCRIPTION OF SUPPORT UNITS .................................................................................................................. 5 5.6 TEST LOCATION ............................................................................................................................................ 5 5.7 TEST FACILITY .............................................................................................................................................. 6 6 EQUIPMENTS LIST ......................................................................................................................................... 7 7 TEST RESULTS AND MEASUREMENT DATA ......................................................................................... 8 7.1 ANTENNA REQUIREMENT .............................................................................................................................. 8 7.2 CONDUCTED EMISSIONS ................................................................................................................................ 9 7.3 RADIATED EMISSIONS ................................................................................................................................. 10 7.4 OCCUPIED BANDWIDTH............................................................................................................................... 16 8 TEST SETUP PHOTOGRAPHS .................................................................................................................. 18 9 EUT CONSTRUCTIONAL DETAILS........................................................................................................... 18 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 5 of 18 5 General Information 5.1 Client Information Applicant: MINE SITE TECHNOLOGIES PTY LTD Address of Applicant: Level 5, 113 Wicks Rd., North Ryde NSW 2113 Manufacturer: Mine Site Technologies China Co.,Ltd Address of Manufacturer: 4th Floor,Building 1, No.1413 Moganshan Road, Hangzhou, China,310011 Factory: Mine Site Technologies China Co.,Ltd Address of Factory: 4th Floor,Building 1, No.1413 Moganshan Road, Hangzhou, China,310011 5.2 General Description of E.U.T. Product Description: RFID Tag Initiator Power Supply: DC 24V 5.3 Technical Specifications Operation Frequency: 125kHz Modulation Type: OOK Antenna Type: Integral loop antenna 5.4 E.U.T Operation Mode Test Mode Description of Test Mode Engineering mode Keep EUT working in continuous transmitting 5.5 Description of Support Units The EUT has been tested independently. 5.6 Test Location Radiated Emissions test was sub-contracted at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch E&E Lab, No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 Other tests were performed at: SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. No.588 West Jindu Road, Songjiang District, Shanghai, China. 201612. Tel: +86 21 6191 5666 Fax: +86 21 6191 5678 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 6 of 18 5.7 Test Facility The test facility is recognized, certified, or accredited by the following organizations:  CNAS (No. CNAS L0599) CNAS has accredited SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. Date of expiry: 2017-07-14.  FCC – Registration No.: 402683 SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been registered and fully described in a report filed with the Federal Communications Commission (FCC). The acceptance letter from the FCC is maintained in our files. Registration No.: 402683, Expiry Date: 2017-09-16.  Industry Canada (IC) – IC Assigned Code: 8617A The 3m Semi-anechoic chamber of SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 8617A-1. Expiry Date: 2017-06-18.  VCCI (Member No.: 3061) The 3m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: R-3868 and C-4336 respectively. Date of Registration: 2012-05-29. Date of Expiry: 2017-11-16 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 7 of 18 6 Equipments List Item Test Equipment Manufacturer Model No. Inventory No. Cal. Date Cal. Due date 10m Semi-Anechoic 1 SAEMC FSAC1018 SEL0303 2014-08-02 2015-08-01 Chamber 2 EMI Test Receiver Rohde & Schwarz ESR SEL0295 2014-06-19 2015-06-18 3 EMI Test software AUDIX E3 SEL0050 N/A N/A 4 Coaxial cable SGS N/A SEL0288 2014-06-11 2015-06-10 5 Coaxial cable SGS N/A SEL0275 2014-06-11 2015-06-10 6 Coaxial cable SGS N/A SEL0274 2014-06-11 2015-06-10 BiConiLog Antenna 7 Schwarzbeck VULB9160 SEL0308 2014-07-15 2015-07-14 (30M-1GHz) BiConiLog Antenna 8 Schwarzbeck VULB9160 SEL0309 2014-07-15 2015-07-14 (30M-1GHz) Horn Antenna 9 Rohde & Schwarz HF907 SEL0310 2014-07-17 2015-07-16 (1-18GHz) Sonoma Instrument 10 Pre-amplifier 310N SEL0298 2014-07-29 2015-07-28 Co Compliance Pre-Amplifier 11 Directions Systems PAP-0126 SEL0168 2014-10-25 2015-10-24 (0.1-26.5GHz) Inc. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 8 of 18 7 Test results and Measurement Data 7.1 Antenna Requirement 15.203 Requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. EUT Antenna: The antenna is integrated loop antenna and no consideration of replacement. Antenna Configuration: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 9 of 18 7.2 Conducted Emissions Test Frequency Range: 150kHz to 30MHz Limit: Limit (dBuV) Frequency range (MHz) Quasi-peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. Test Procedure: 1) The mains terminal disturbance voltage test was conducted in a shielded room. 2) The EUT was connected to AC power source through a LISN 1 (Line Impedance Stabilization Network) which provides 50Ω/50µH + 5Ω linear impedance. The power cables of all other units of the EUT were connected to a second LISN 2, which was bonded to the ground reference plane in the same way as the LISN 1 for the unit being measured. A multiple socket outlet strip was used to connect multiple power cables to a single LISN provided the rating of the LISN was not exceeded. 3) The tabletop EUT was placed upon a non-metallic table 0.8m above the ground reference plane. And for floor-standing arrangement, the EUT was placed on the horizontal ground reference plane, 4) The test was performed with a vertical ground reference plane. The rear of the EUT shall be 0.4 m from the vertical ground reference plane. The vertical ground reference plane was bonded to the horizontal ground reference plane. The LISN 1 was placed 0.8 m from the boundary of the unit under test and bonded to a ground reference plane for LISNs mounted on top of the ground reference plane. This distance was between the closest points of the LISN 1 and the EUT. All other units of the EUT and associated equipment was at least 0.8 m from the LISN 2. 5) In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.10 on conducted measurement. Test Setup: Test Results: N/A This EUT is powered by DC source; therefore the AC Conducted Emission test is not applicable. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 10 of 18 7.3 Radiated Emissions Test frequency range: 9KHz – 1GHz Test Site: Measurement Distance: 3m for above 30MHz (Semi-Anechoic Chamber) 10m for below 30MHz (Semi-Anechoic Chamber) Receiver Setup: Frequency (MHz) RBW VBW Detector 0.009-0.015 200Hz 1KHz Quasi-peak 0.015-30 9kHz 30KHz Quasi-peak 30-1000 120 kHz 300KHz Quasi-peak Note: The emission limits shown in the above table are based on measurement instrumentation employing a CISPR quasi-peak detector. For the frequency bands 9~90 kHz, 110~490 kHz and above 1000 MHz, the radiated emission limits are based on measurements employing an average detector. Limit: Field strength Measurement Limit @3m Frequency (MHz) (µV/m) distance (m) (dBµV/m ) 0.009-0.490 2400/F(kHz) 300 128.5 ~ 93.8 0.490-1.705 24000/F(kHz) 30 73.8 ~63.0 1.705-30 30 30 69.5 30-88 100 3 40.0 88-216 150 3 43.5 216-960 200 3 46.0 960-1000 500 3 54.0 NOTE: (1) For test distance other than what is specified, but fulfilling the requirements of section 15.31(f) (2) the field strength is calculated by adding additionally an extrapolation factor of 40dB/decade (inverse linear distance for field strength measurements). So the Distance Extrapolation Factor in dB is 40*log (DTEST / DSPEC) where DTEST = Test Distance and DSPEC = Specified Distance. Field strength limit (dBµV/m)@test distance= Field strength limit (dBµV/m)@specified distance -Distance Extrapolation Factor (2) The lower limit shall apply at the transition frequencies. Test Procedure: a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set fixed away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 11 of 18 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. g. The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis positioning which it is worse case, only the test worst case mode is recorded in the report. Test Setup: Figure 1. Below 30MHz Figure 2. 30MHz to 1GHz Test Results: Pass This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 12 of 18 Test Data: 9kHz-150kHz: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 13 of 18 150 kHz-30 MHz: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 14 of 18 30MHz-1GHz: Vertical Read Antenna Preamp Cable Result Limit Over Item Freq. Detector Level Factor Factor Loss Level Line Limit (Mark) (MHz) (dBµV) (dB/m) (dB) (dB) (dBµV/m) (dBµV/m) (dB) 1 30.11 38.66 12.50 23.72 0.55 27.99 40.00 -12.01 QP 2 33.33 36.95 12.57 23.71 0.15 25.96 40.00 -14.04 QP 3 81.50 36.29 8.46 23.67 0.72 21.80 40.00 -18.20 QP 4 85.90 32.65 8.56 23.67 0.77 18.31 40.00 -21.69 QP 5 289.00 31.04 11.43 23.66 1.81 20.62 46.00 -25.38 QP 6 938.83 23.72 23.44 23.94 3.56 26.78 46.00 -19.22 QP This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 15 of 18 Horizontal Read Antenna Preamp Cable Result Limit Over Item Freq. Detector Level Factor Factor Loss Level Line Limit (Mark) (MHz) (dBµV) (dB/m) (dB) (dB) (dBµV/m) (dBµV/m) (dB) 1 74.40 34.93 9.68 23.67 0.64 21.58 40.00 -18.42 QP 2 78.41 34.74 8.77 23.67 0.69 20.53 40.00 -19.47 QP 3 239.99 36.80 10.10 23.64 1.53 24.79 46.00 -21.21 QP 4 267.55 36.55 10.86 23.66 1.67 25.42 46.00 -20.58 QP 5 284.98 36.88 11.34 23.66 1.80 26.36 46.00 -19.64 QP 6 303.54 36.34 11.92 23.67 1.90 26.49 46.00 -19.51 QP Remark: The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic equation with a sample calculation is as follows: Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 16 of 18 7.4 Occupied Bandwidth Test Setup: Requirements: Intentional radiators operating under the alternative provisions to the general emission limits, as contained in §15.217 through §15.257 and in subpart E of this part, must be designed to ensure that the 20 dB bandwidth of the emission is contained within the frequency band designated in the rule section under which the equipment is operated. The requirement to contain the 20 dB bandwidth of the emission within the specified frequency band includes the effects from frequency sweeping, frequency hopping and other modulation techniques that may be employed as well as the frequency stability of the transmitter over expected variations in temperature and supply voltage. If frequency stability is not specified in the regulations, it is recommended that the fundamental emission be kept within at least the central 80% of the permitted band in order to minimize the possibility of out-of-band operation. Test Result: Pass Measurement Data: 20dB bandwidth (kHz) Result 7.091 Pass This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 17 of 18 Test plot as follows: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM141100297201 Page: 18 of 18 8 Test Setup Photographs Refer to the < EX09_Test Setup Photos-FCC > 9 EUT Constructional Details Refer to the < EX09_External Photos-FCC> & < EX09_Internal Photos-FCC>. --End of the Report-- This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.


Document Created: 2015-10-21 08:48:00
Document Modified: 2015-10-21 08:48:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC