Test Report

FCC ID: N6SLFECIM

Test Report

Download: PDF
FCCID_1925598

Certification Test Report FCC ID: N6SLFECIM IC: 827B-LFECIM FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Report Number: 13-0074.W06.1A Manufacturer: Gilbarco Inc. Model: LFECIM Test Begin Date: February 23, 2013 Test End Date: March 6, 2013 Report Issue Date: March 22, 2013 FOR THE SCOPE OF ACCREDITATION UNDER LAB Code 200612-0 This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Reviewed by: Kirby Munroe Director, Wireless Certifications ACS, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 16 pages 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598

TABLE OF CONTENTS 1 GENERAL ............................................................................................................................................ 3 1.1 PURPOSE.......................................................................................................................................... 3 1.2 PRODUCT DESCRIPTION ................................................................................................................... 3 1.3 TEST METHODOLOGY AND CONSIDERATIONS ................................................................................. 3 2 TEST FACILITIES.............................................................................................................................. 4 2.1 LOCATION ....................................................................................................................................... 4 2.2 LABORATORY ACCREDITATIONS/RECOGNITIONS/CERTIFICATIONS ................................................ 4 2.3 RADIATED EMISSIONS TEST SITE DESCRIPTION .............................................................................. 5 2.3.1 Semi-Anechoic Chamber Test Site.......................................................................................... 5 2.3.2 Open Area Tests Site (OATS) ................................................................................................. 6 2.4 CONDUCTED EMISSIONS TEST SITE DESCRIPTION ........................................................................... 7 3 APPLICABLE STANDARD REFERENCES.................................................................................... 7 4 LIST OF TEST EQUIPMENT............................................................................................................ 8 5 SUPPORT EQUIPMENT.................................................................................................................... 9 6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM ........................................................... 9 7 SUMMARY OF TESTS......................................................................................................................10 7.1 ANTENNA REQUIREMENT – FCC: SECTION 15.203 ........................................................................10 7.2 POWER LINE CONDUCTED EMISSIONS – FCC: SECTION 15.207 IC: RSS-GEN 7.2.4.......................10 7.2.1 Measurement Procedure........................................................................................................10 7.2.2 Measurement Results.............................................................................................................10 7.3 RADIATED EMISSIONS – FCC CFR 47 PART 15.209 / RSS-210 SECTION 2.5..................................11 7.3.1 Measurement Procedure........................................................................................................11 7.3.2 Distance Correction for Measurements Below 30 MHz – Part 15.31 ...................................12 7.3.3 Measurement Results.............................................................................................................12 7.3.4 Sample Calculation................................................................................................................13 7.4 20DB / 99% BANDWIDTH – FCC: SECTION 15.215, IC: RSS-GEN 4.6.1.........................................14 7.4.1 Measurement Procedure........................................................................................................14 7.4.2 Measurement Results.............................................................................................................14 8 CONCLUSION ....................................................................................................................................16 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 1 GENERAL 1.1 Purpose The purpose of this report is to demonstrate compliance with Part 15 Subpart C of the FCC’s Code of Federal Regulations and Industry Canada’s Radio Standards Specification RSS-210 for modular approval certification. 1.2 Product description The model LFECIM is a Radio Frequency Identification Device (RFID) which is designed for use in conjunction with passive transponders (not requiring a battery), Texas Instruments Part # RI- TRP-Series. The user carries the handheld transponder and the transmitter portion of the LFECIM operates at 134.2kHz. Technical Information: Band of Operation: 134 kHz Number of Channels: 1 Modulation Format: FSK Antenna Type: Integral Loop Operating Voltage: 24 VDC (Host) Manufacturer Information: Gilbarco Inc. 7300 West Friendly Ave. Greensboro NC 27420 Test Sample Serial Number(s): 64219196 Test Sample Condition: The test samples were provided in good working order with no visible defects. 1.3 Test Methodology and Considerations The EUT was tested in an orientation of typical installation. A tag was presented to the EUT (i.e. tag reader) to provide continuous transmit functionality for test purposes. In order to comply with 15.209 regulations, the LFECIM needed a ferrite placed on the power/data cable. The part number of the ferrite used was Steward Ferrite 29A2025-0A0. See the external photo exhibit included in this filing for photographs of this modification. ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 3

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 2 TEST FACILITIES 2.1 Location The radiated and conducted emissions test sites are located at the following address: Advanced Compliance Solutions 5015 B.U. Bowman Drive Buford, GA 30518 Phone: (770) 831-8048 Fax: (770) 831-8598 2.2 Laboratory Accreditations/Recognitions/Certifications ACS is accredited to ISO/IEC 17025 by the National Institute of Standards and Technology under their National Voluntary Laboratory Accreditation Program (NVLAP), Lab Code 200612-0. Unless otherwise specified, all tests methods described within this report are covered under the ISO/IEC 17025 scope of accreditation. The Semi-Anechoic Chamber Test Site, Open Area Test Site (OATS) and Conducted Emissions Site have been fully described, submitted to, and accepted by the FCC, Industry Canada and the Japanese Voluntary Control Council for Interference by information technology equipment. FCC Registration Number: 511277 Industry Canada Lab Code: IC 4175A-1 VCCI Member Number: 1831 • VCCI OATS Registration Number R-1526 • VCCI Conducted Emissions Site Registration Number: C-1608 ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 4

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 2.3 Radiated Emissions Test Site Description 2.3.1 Semi-Anechoic Chamber Test Site The Semi-Anechoic Chamber Test Site consists of a 20’ x 30’ x 18’ shielded enclosure. The chamber is lined with Toyo Ferrite Grid Absorber, model number FFG-1000. The ferrite tile grid is 101 x 101 x 19mm thick and weighs approximately 550 grams. These tiles are mounted on steel panels and installed directly on the inner walls of the chamber. The turntable is 150cm in diameter and is located 160cm from the back wall of the chamber. The chamber is grounded via 1 - 8’ copper ground rod, installed at the center of the back wall, it is bound to the ground plane using 3/4" stainless steel braided cable. The turntable is all steel, flush mounted table installed in an all steel frame. The table is remotely operated from inside the control room located 25’ from the range. The turntable is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table. The steel fingers make constant contact with the ground plane during operation. Behind the turntable is a 3’ x 6’ x 4’ deep shielded pit used for support equipment if necessary. The pit is equipped with 1 - 4” PVC chases from the turntable to the pit that allow for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can be supplied to the EUT from the pit. A diagram of the Semi-Anechoic Chamber Test Site is shown in Figure 2.3-1 below: 3 Meters 5 Feet Diameter 20 Feet 30 Feet Figure 2.3-1: Semi-Anechoic Chamber Test Site ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 5

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 2.3.2 Open Area Tests Site (OATS) The open area test site consists of a 40’ x 66’ concrete pad covered with a perforated electro- plated galvanized sheet metal. The perforations in the sheet metal are 1/8” holes that are staggered every 3/16”. The individual sheets are placed to overlap each other by 1/4” and are riveted together to provide a continuous seam. Rivets are spaced every 3” in a 3 x 20 meter perimeter around the antenna mast and EUT area. Rivets in the remaining area are spaced as necessary to properly secure the ground plane and maintain the electrical continuity. The entire ground plane extends 12’ beyond the turntable edge and 16’ beyond the antenna mast when set to a 10 meter measurement distance. The ground plane is grounded via 4 - 8’ copper ground rods, each installed at a corner of the ground plane and bound to the ground plane using 3/4" stainless steel braided cable. The turntable is an all aluminum 10’ flush mounted table installed in an all aluminum frame. The table is remotely operated from inside the control room located 40’ from the range. The turntable is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table. The steel fingers make constant contact with the ground plane during operation. Adjacent to the turntable is a 7’ x 7’ square and 4’ deep concrete pit used for support equipment if necessary. The pit is equipped with 5 - 4” PVC chases from the pit to the control room that allow for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can be supplied to the EUT from the pit. The pit is covered with 2 sheets of 1/4" diamond style re-enforced steel sheets. The sheets are painted to match the perforated steel ground plane; however the underside edges have been masked off to maintain the electrical continuity of the ground plane. All reflecting objects are located outside of the ellipse defined in ANSI C63.4. A diagram of the Open Area Test Site is shown in Figure 2.3-2 below: 10 3 Meters 40 7x7x4 Pit 66 Feet Figure 2.3-2: Open Area Test Site ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 6

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 2.4 Conducted Emissions Test Site Description The AC mains conducted EMI site is located in the main EMC lab. It consists of an 8’ x 8’ solid aluminum horizontal ground reference plane (GRP) bonded every 3” to an 8’ X 8’ vertical ground plane. The site is of sufficient size to test table top and floor standing equipment in accordance with section 6.1.4 of ANSI C63.4. A diagram of the room is shown below in figure 4.1.3-1: Vertical Ground Plane (8’ x 8’) Non-Conductive EUT Table (1m x 1.5m x .8m) .4 Meters .8 Meters Horizontal Ground Plane (8’ x 8’) LISN Figure 2.4-1: AC Mains Conducted EMI Site 3 APPLICABLE STANDARD REFERENCES The following standards were used:  ANSI C63.4-2003: Method of Measurements of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the 9KHz to 40GHz  ANSI C63.10-2009: American National Standard for Testing Unlicensed Wireless Devices  US Code of Federal Regulations (CFR): Title 47, Part 2, Subpart J: Equipment Authorization Procedures, 2013  US Code of Federal Regulations (CFR): Title 47, Part 15, Subpart C: Radio Frequency Devices, Intentional Radiators, 2013  Industry Canada Radio Standards Specification: RSS-210 - Low-power License-exempt Radiocommunication Devices (All Frequency Bands): Category I Equipment, Issue 8, Dec 2010  Industry Canada Radio Standards Specification: RSS-GEN – General Requirements and Information for the Certification of Radiocommunication Equipment, Issue 3, Dec 2010. ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 7

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 4 LIST OF TEST EQUIPMENT The calibration interval of test equipment is annually or the manufacturer’s recommendations. Where the calibration interval deviates from the annual cycle based on the instrument manufacturer’s recommendations, it shall be stated below. Table 4-1: Test Equipment Calibration AssetID Manufacturer Model # Equipment Type Serial # Last Calibration Date Due Date 1 Rohde & Schwarz ESMI - Display Spectrum Analyzers 833771/007 8/2/2012 8/2/2014 2 Rohde & Schwarz ESMI-Receiver Spectrum Analyzers 839587/003 8/2/2012 8/2/2014 40 EMCO 3104 Antennas 3211 2/14/2013 2/14/2015 73 Agilent 8447D Amplifiers 2727A05624 9/28/2012 9/28/2013 78 EMCO 6502 Antennas 9104-2608 2/5/2013 2/5/2015 153 EMCO 3825/2 LISN 9411-2268 7/31/2012 7/31/2014 Chamber EMI 167 ACS Cable Set Cable Set 167 12/17/2012 12/17/2013 168 Hewlett Packard 11947A Attenuators 44829 2/1/2013 2/1/2014 283 Rohde & Schwarz FSP40 Spectrum Analyzers 1000033 8/1/2012 8/1/2013 324 ACS Belden Cables 8214 6/26/2012 6/26/2013 412 Electro Metrics LPA-25 Antennas 1241 7/27/2012 7/27/2014 RE90 Agilent E7404A Analyzers US40240143 11/28/2012 11/28/2013 ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 8

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 5 SUPPORT EQUIPMENT Table 5-1: Support Equipment Item Equipment Type Manufacturer Model Number Serial Number MINI-PS-100- 1 Power Supply Phoenix Contact 50013173 240AC/24DC/4 2 Laptop Dell D630 (PP18L) N/A CN-0F7970-71615- 3 Power Supply Dell PA-1650-05D2 55M-6BF4 4 Clip-on Ferrite Steward 29A2025-0A0 N/A 5 RFID Tag TIRIS N/A N/A 6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM 5 EUT 2 3 120VAC / 60Hz B C D 4 A 1 120VAC / 60Hz E A: DC Power Wires, 30cm, Unshielded B: Serial Cable, 475cm, Unshielded C: DC Power Cable, 200c, Unshielded D: AC Power Cable, 100cm, Unshielded E: AC Power Cable, 150cm, Unshielded ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 9

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 7 SUMMARY OF TESTS Along with the tabular data shown below, plots were taken of all signals deemed important enough to document. 7.1 Antenna Requirement – FCC: Section 15.203 The antenna is a loop antenna which is non-detachable and integral in design. 7.2 Power Line Conducted Emissions – FCC: Section 15.207 IC: RSS-Gen 7.2.4 7.2.1 Measurement Procedure ANSI C63.4 sections 6 and 7 were the guiding documents for this evaluation. Conducted emissions were performed from 150kHz to 30MHz with the spectrum analyzer’s resolution bandwidth set to 9kHz and the video bandwidth set to 30kHz. The calculation for the conducted emissions is as follows: Corrected Reading = Analyzer Reading + LISN Loss + Cable Loss Margin = Applicable Limit - Corrected Reading 7.2.2 Measurement Results Results of the test are shown below in and Tables 7.2.2-1 and 7.2.2-2. Table 7.2.2-1: Conducted EMI Results – Line 1 Uncorrected Total Corrected Level Limit Margin (dB) Frequency Reading Correction (MHz) Factor Quasi- (dB) Average Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Peak 10.468 27.238 27.875 10.239 37.477 38.114 60 50 22.523 11.886 9.93209 27.384 28.45 10.178 37.562 38.628 60 50 22.438 11.372 9.66254 27.974 29.091 10.198 38.172 39.289 60 50 21.828 10.711 9.39409 28.136 28.798 10.218 38.353 39.016 60 50 21.647 10.984 8.85894 25.902 25.971 10.229 36.13 36.2 60 50 23.87 13.8 0.177069 34.415 29.151 9.964 44.379 39.115 65.227 55.227 20.848 16.111 Table 7.2.2-2: Conducted EMI Results – Line 2 Uncorrected Total Corrected Level Limit Margin (dB) Frequency Reading Correction (MHz) Factor Quasi- (dB) Average Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Peak 8.85849 25.246 25.784 10.229 35.474 36.012 60 50 24.526 13.988 2.42909 25.971 26.187 10.004 35.975 36.191 56 46 20.025 9.809 2.33994 26.223 26.432 10.003 36.226 36.435 56 46 19.774 9.565 1.98757 25.246 26.356 9.999 35.245 36.355 56 46 20.755 9.645 0.221644 29.503 25.254 9.926 39.429 35.18 63.953 53.953 24.524 18.773 0.17585 33.899 29.303 9.967 43.866 39.27 65.261 55.261 21.396 15.991 ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 10

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 7.3 Radiated Emissions – FCC CFR 47 Part 15.209 / RSS-210 Section 2.5 7.3.1 Measurement Procedure Section 15.33(a)(4) specifies, if the intentional radiator contains a digital device, regardless of whether this digital device controls the functions of the intentional radiator or the digital device is used for additional control or function purposes other than to enable the operation of the intentional radiator, the frequency range shall be investigated up to frequency specified in 15.33(b)(1) for unintentional radiators. The upper frequency range for the digital device is th 1000MHz which greater than the 10 harmonic of the fundamental frequency. The upper frequency range measured was 1000MHz. Measurements below 30MHz were performed in a semi-anechoic chamber with a 3 meter separation distance between the EUT and measurement antenna. The EUT was rotated 360º and the loop antenna rotated about the vertical axis to maximize each emission. The magnetic loop receiving antenna was positioned with its center 1 meter above the ground. The spectrum analyzer’s resolution and video bandwidth was set to 200 Hz and 1 kHz respectively for frequencies below 150 kHz and 9 kHz and 30 kHz respectively for frequencies above 150 kHz and below 30 MHz. For measurements in the frequency bands 9-90 kHz and 110-490 kHz, an average detector was used. When average measurements are specified, the peak emissions were also compared to a limit corresponding to 20 dB above the maximum permitted average limit according to Part 15.35. All other emissions were measured using a Quasi-peak detector. Measurements above 30 MHz were performed in a semi-anechoic chamber with a 3 meter separation distance between the EUT and measurement antenna. The EUT was rotated through 360° and the receive antenna height was varied from 1m to 4m so that the maximum radiated emissions level would be detected. For frequencies below 1000 MHz, quasi-peak measurements were made using a resolution bandwidth (RBW) of 120 kHz and a video bandwidth (VBW) of 300 kHz. For measurements of fundamental emissions where average measurements are specified, the spectrum analyzer’s resolution bandwidth (RBW) was adjusted equal to or greater than the emission bandwidth (EBW). ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 11

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 7.3.2 Distance Correction for Measurements Below 30 MHz – Part 15.31 Radiated measurements were performed at a distance closer than 300 meters and 30m as required, according to Part 15.209. Therefore a correction factor was applied to account for propagation loss at the specified distance. The propagation loss was determined by using the square of an inverse linear distance extrapolation factor (40dB/decade) according to 15.31. A sample calculation of the distance correction factor is shown below for limits expressed at a 300m measurement distance and a 30m measurement distance. Distance correction factor (300m Specified Test Distance) = 40*Log (Test Distance/300) = 40*Log (3/300) = - 80 dB Distance correction factor (30m Specified Test Distance) = 40*Log (Test Distance/30) = 40*Log (3/30) = - 40 dB 7.3.3 Measurement Results Results of the test are given in Tables 7.3.3-1 to 7.3.3-2. Table 7.3.3-1: Fundamental Field Strength Level Antenna Correction Corrected Level Limit Margin Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB) (MHz) pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg 0.134 91.80 91.71 H 10.77 102.57 102.48 125.1 105.1 22.5 2.6 Note: RBW set to 9kHz (RBW>>EBW). Table 7.3.3-2: Radiated Emissions Level Antenna Correction Corrected Level Limit Margin Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB) (MHz) pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg 0.402 56.43 56.10 H 10.60 67.03 66.70 115.5 95.5 48.5 28.8 0.06156 57.31 56.43 H 11.22 68.53 67.65 131.8 111.8 63.3 44.2 0.67 ------ 44.01 H 10.80 ------ 54.81 ------ 71.1 ------ 16.3 0.938 ------ 38.25 H 10.78 ------ 49.03 ------ 68.2 ------ 19.1 1.206 ------ 33.91 H 10.92 ------ 44.83 ------ 66.0 ------ 21.1 1.4768 ------ 30.53 H 10.95 ------ 41.48 ------ 64.2 ------ 22.7 1.7446 ------ 27.61 H 10.97 ------ 38.58 ------ 69.5 ------ 30.90 2.013 ------ 24.94 H 11.01 ------ 35.95 ------ 69.5 ------ 33.60 2.2814 ------ 23.09 H 11.17 ------ 34.26 ------ 69.5 ------ 35.20 19.1906 ------ 21.26 H 11.33 ------ 32.59 ------ 69.5 ------ 36.90 19.459 ------ 23.47 H 11.32 ------ 34.79 ------ 69.5 ------ 34.70 19.7274 ------ 22.53 H 11.31 ------ 33.84 ------ 69.5 ------ 35.70 19.9958 ------ 20.83 H 11.30 ------ 32.13 ------ 69.5 ------ 37.40 26.5716 ------ 25.93 H 10.15 ------ 36.08 ------ 69.5 ------ 33.40 26.84 ------ 25.27 H 10.10 ------ 35.37 ------ 69.5 ------ 34.10 27.1084 ------ 23.52 H 10.04 ------ 33.56 ------ 69.5 ------ 35.90 34.81 ------ 44.57 V -13.75 ------ 30.82 ------ 40.0 ------ 9.20 57.53 ------ 49.47 V -13.60 ------ 35.87 ------ 40.0 ------ 4.10 64.69 ------ 49.32 V -14.53 ------ 34.79 ------ 40.0 ------ 5.20 215.38 ------ 45.94 H -13.50 ------ 32.44 ------ 43.5 ------ 11.10 594.67 ------ 20.34 V -4.70 ------ 15.64 ------ 46.0 ------ 30.40 677.33 ------ 20.83 V -1.12 ------ 19.71 ------ 46.0 ------ 26.30 ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 12

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 7.3.4 Sample Calculation Example Calculation – Average/Quasi-Peak Limit < 30MHz Measurement Distance 300m @ 134 kHz Limit (dBuV/m) = 20*Log(2400/F(kHz)) - Distance Correction Factor (Section 7.3.2) Limit (dBuV/m) = 20*Log(2400/134) + 80 Limit (dBuV/m) = 105.06 Example Calculation - 134 kHz (See Table 7.3.3-1) RC = RU + CFT Where: CFT = Total Correction Factor (AF+CA+AG) RU = Uncorrected Reading RC = Corrected Level AF = Antenna Factor CA = Cable Attenuation AG = Amplifier Gain Peak: Corrected Level: 91.80 + 10.77 = 102.57dBuV Margin: 125.06dBuV – 102.57dBuV = 22.5 dB Average: Corrected Level: 91.71 + 10.77 = 102.48dBuV Margin: 105.06dBuV – 102.48dBuV = 2.6 dB ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 13

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 7.4 20dB / 99% Bandwidth – FCC: Section 15.215, IC: RSS-Gen 4.6.1 7.4.1 Measurement Procedure The span of the spectrum analyzer display was set between two times and five times the occupied bandwidth (OBW) of the emission. The RBW of the spectrum analyzer was set to 100Hz. The trace was set to max hold with a peak detector active. The Delta function of the analyzer was utilized to determine the 20 dB bandwidth of the emission. The occupied bandwidth measurement function of the analyzer was used for the 99% bandwidth. The span of the analyzer shall be set to capture all products of the modulation process, including the emission skirts. The resolution bandwidth shall be set to as close to 1% of the selected span as is possible without being below 1%. The video bandwidth shall be set to > 3 times the resolution bandwidth. A sampling detector was used. 7.4.2 Measurement Results Results are shown below in table 7.4.2-1 and figure 7.4.2-1 to 7.4.2-2: Table 7.4.2-1: 20dB / 99% Bandwidth Frequency 20dB Bandwidth 99% Bandwidth [kHz] [kHz] [kHz] 134 1.75 4.34 * RBW 100 Hz Marker 1 [T1 ] 72.08 dBµV Ref 100 dBµV Att 30 dB AQT 40 ms 135.002500000 kHz 100 Delta 1 [T1 ] 0.77 dB -1.750000000 kHz A 90 SGL 1 PK VIEW 80 1 1 70 60 50 FFT 40 30 20 10 0 Center 134.2 kHz 1 kHz/ Span 10 kHz Date: 6.MAR.2013 08:59:17 Figure 7.4.2-1: 20dB Bandwidth Plot ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 14

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM * RBW 100 Hz Marker 1 [T1 ] 92.14 dBµV Ref 100 dBµV Att 10 dB AQT 40 ms 134.202500000 kHz 100 OBW 4.340000000 kHz 1 Temp 1 [T1 OBW] 90 60.17 dBµV A SGL 132.025000000 kHz 1 SA * Temp 2 [T1 OBW] VIEW 80 64.39 dBµV 136.365000000 kHz 70 T2 T1 60 50 FFT 40 30 20 10 0 Center 134.2 kHz 1 kHz/ Span 10 kHz Date: 6.MAR.2013 09:09:43 Figure 7.4.2-2: 99% Bandwidth Plot ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 15

Model: LFECIM FCC ID: N6SLFECIM IC: 827B-LFECIM 8 CONCLUSION In the opinion of ACS, Inc., the LFECIM, manufactured by Gilbarco Inc. meet the requirements of FCC Part 15 subpart C and Industry Canada’s Radio Standards Specification RSS-210. END REPORT ACS Report: 13-0074.W06.1A Advanced Compliance Solutions Page 16


Document Created: 2013-03-25 15:19:02
Document Modified: 2013-03-25 15:19:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC